Suman Ghosh [Tue, 19 Dec 2023 14:26:33 +0000 (19:56 +0530)]
octeontx2-af: Fix marking couple of structure as __packed
Couple of structures was not marked as __packed. This patch
fixes the same and mark them as __packed.
Fixes: 42006910b5ea ("octeontx2-af: cleanup KPU config data") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 Dec 2023 07:29:04 +0000 (07:29 +0000)]
Merge branch 'nfc-refcounting'
@ 2023-12-19 17:49 Siddh Raman Pant
2023-12-19 17:49 ` [PATCH net-next v7 1/2] nfc: llcp_core: Hold a ref to llcp_local->dev when holding a ref to llcp_local Siddh Raman Pant
2023-12-19 17:49 ` [PATCH net-next v7 2/2] nfc: Do not send datagram if socket state isn't LLCP_BOUND Siddh Raman Pant
0 siblings, 2 replies; 4+ messages in thread
Siddh Raman Pant says:
====================
[PATCH net-next v7 0/2] nfc: Fix UAF during datagram sending caused by missing refcounting
Changes in v7:
- Stupidly reverted ordering in recv() too, fix that.
- Remove redundant call to nfc_llcp_sock_free().
Changes in v6:
- Revert label introduction from v4, and thus also v5 entirely.
Changes in v5:
- Move reason = LLCP_DM_REJ under the fail_put_sock label.
- Checkpatch now warns about == NULL check for new_sk, so fix that,
and also at other similar places in the same function.
Changes in v4:
- Fix put ordering and comments.
- Separate freeing in recv() into end labels.
- Remove obvious comment and add reasoning.
- Picked up r-bs by Suman.
Changes in v3:
- Fix missing freeing statements.
Changes in v2:
- Add net-next in patch subject.
- Removed unnecessary extra lock and hold nfc_dev ref when holding llcp_sock.
- Remove last formatting patch.
- Picked up r-b from Krzysztof for LLCP_BOUND patch.
---
For connectionless transmission, llcp_sock_sendmsg() codepath will
eventually call nfc_alloc_send_skb() which takes in an nfc_dev as
an argument for calculating the total size for skb allocation.
virtual_ncidev_close() codepath eventually releases socket by calling
nfc_llcp_socket_release() (which sets the sk->sk_state to LLCP_CLOSED)
and afterwards the nfc_dev will be eventually freed.
When an ndev gets freed, llcp_sock_sendmsg() will result in an
use-after-free as it
(1) doesn't have any checks in place for avoiding the datagram sending.
(2) calls nfc_llcp_send_ui_frame(), which also has a do-while loop
which can race with freeing. This loop contains the call to
nfc_alloc_send_skb() where we dereference the nfc_dev pointer.
nfc_dev is being freed because we do not hold a reference to it when
we hold a reference to llcp_local. Thus, virtual_ncidev_close()
eventually calls nfc_release() due to refcount going to 0.
Since state has to be LLCP_BOUND for datagram sending, we can bail out
early in llcp_sock_sendmsg().
Please review and let me know if any errors are there, and hopefully
this gets accepted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
nfc: Do not send datagram if socket state isn't LLCP_BOUND
As we know we cannot send the datagram (state can be set to LLCP_CLOSED
by nfc_llcp_socket_release()), there is no need to proceed further.
Thus, bail out early from llcp_sock_sendmsg().
Signed-off-by: Siddh Raman Pant <code@siddh.me> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Suman Ghosh <sumang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfc: llcp_core: Hold a ref to llcp_local->dev when holding a ref to llcp_local
llcp_sock_sendmsg() calls nfc_llcp_send_ui_frame() which in turn calls
nfc_alloc_send_skb(), which accesses the nfc_dev from the llcp_sock for
getting the headroom and tailroom needed for skb allocation.
Parallelly the nfc_dev can be freed, as the refcount is decreased via
nfc_free_device(), leading to a UAF reported by Syzkaller, which can
be summarized as follows:
When a reference to llcp_local is acquired, we do not acquire the same
for the nfc_dev. This leads to freeing even when the llcp_local is in
use, and this is the case with the UAF described above too.
Thus, when we acquire a reference to llcp_local, we should acquire a
reference to nfc_dev, and release the references appropriately later.
References for llcp_local is initialized in nfc_llcp_register_device()
(which is called by nfc_register_device()). Thus, we should acquire a
reference to nfc_dev there.
nfc_unregister_device() calls nfc_llcp_unregister_device() which in
turn calls nfc_llcp_local_put(). Thus, the reference to nfc_dev is
appropriately released later.
Reported-and-tested-by: syzbot+bbe84a4010eeea00982d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=bbe84a4010eeea00982d Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket") Reviewed-by: Suman Ghosh <sumang@marvell.com> Signed-off-by: Siddh Raman Pant <code@siddh.me> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 21 Dec 2023 17:15:37 +0000 (09:15 -0800)]
Merge tag 'net-6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from WiFi and bpf.
Current release - regressions:
- bpf: syzkaller found null ptr deref in unix_bpf proto add
- eth: i40e: fix ST code value for clause 45
Previous releases - regressions:
- core: return error from sk_stream_wait_connect() if sk_wait_event()
fails
- ipv6: revert remove expired routes with a separated list of routes
- wifi rfkill:
- set GPIO direction
- fix crash with WED rx support enabled
- bluetooth:
- fix deadlock in vhci_send_frame
- fix use-after-free in bt_sock_recvmsg
- eth: mlx5e: fix a race in command alloc flow
- eth: ice: fix PF with enabled XDP going no-carrier after reset
- eth: bnxt_en: do not map packet buffers twice
Previous releases - always broken:
- core:
- check vlan filter feature in vlan_vids_add_by_dev() and
vlan_vids_del_by_dev()
- check dev->gso_max_size in gso_features_check()
- mptcp: fix inconsistent state on fastopen race
- phy: skip LED triggers on PHYs on SFP modules
- eth: mlx5e:
- fix double free of encap_header
- fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list()"
* tag 'net-6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
net: check dev->gso_max_size in gso_features_check()
kselftest: rtnetlink.sh: use grep_fail when expecting the cmd fail
net/ipv6: Revert remove expired routes with a separated list of routes
net: avoid build bug in skb extension length calculation
net: ethernet: mtk_wed: fix possible NULL pointer dereference in mtk_wed_wo_queue_tx_clean()
net: stmmac: fix incorrect flag check in timestamp interrupt
selftests: add vlan hw filter tests
net: check vlan filter feature in vlan_vids_add_by_dev() and vlan_vids_del_by_dev()
net: hns3: add new maintainer for the HNS3 ethernet driver
net: mana: select PAGE_POOL
net: ks8851: Fix TX stall caused by TX buffer overrun
ice: Fix PF with enabled XDP going no-carrier after reset
ice: alter feature support check for SRIOV and LAG
ice: stop trashing VF VSI aggregator node ID information
mailmap: add entries for Geliang Tang
mptcp: fill in missing MODULE_DESCRIPTION()
mptcp: fix inconsistent state on fastopen race
selftests: mptcp: join: fix subflow_send_ack lookup
net: phy: skip LED triggers on PHYs on SFP modules
bpf: Add missing BPF_LINK_TYPE invocations
...
Paolo Abeni [Thu, 21 Dec 2023 11:27:28 +0000 (12:27 +0100)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-12-21
Hi David, hi Jakub, hi Paolo, hi Eric,
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 5 day(s) which contain
a total of 4 files changed, 45 insertions(+).
The main changes are:
1) Fix a syzkaller splat which triggered an oob issue in bpf_link_show_fdinfo(),
from Jiri Olsa.
2) Fix another syzkaller-found issue which triggered a NULL pointer dereference
in BPF sockmap for unconnected unix sockets, from John Fastabend.
bpf-for-netdev
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add missing BPF_LINK_TYPE invocations
bpf: sockmap, test for unconnected af_unix sock
bpf: syzkaller found null ptr deref in unix_bpf proto add
====================
Eric Dumazet [Tue, 19 Dec 2023 12:53:31 +0000 (12:53 +0000)]
net: check dev->gso_max_size in gso_features_check()
Some drivers might misbehave if TSO packets get too big.
GVE for instance uses a 16bit field in its TX descriptor,
and will do bad things if a packet is bigger than 2^16 bytes.
Linux TCP stack honors dev->gso_max_size, but there are
other ways for too big packets to reach an ndo_start_xmit()
handler : virtio_net, af_packet, GRO...
Add a generic check in gso_features_check() and fallback
to GSO when needed.
Hangbin Liu [Tue, 19 Dec 2023 06:57:37 +0000 (14:57 +0800)]
kselftest: rtnetlink.sh: use grep_fail when expecting the cmd fail
run_cmd_grep_fail should be used when expecting the cmd fail, or the ret
will be set to 1, and the total test return 1 when exiting. This would cause
the result report to fail if run via run_kselftest.sh.
Before fix:
# ./rtnetlink.sh -t kci_test_addrlft
PASS: preferred_lft addresses have expired
# echo $?
1
After fix:
# ./rtnetlink.sh -t kci_test_addrlft
PASS: preferred_lft addresses have expired
# echo $?
0
Fixes: 9c2a19f71515 ("kselftest: rtnetlink.sh: add verbose flag") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231219065737.1725120-1-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The commit has some race conditions given how expires is managed on a
fib6_info in relation to gc start, adding the entry to the gc list and
setting the timer value leading to UAF. Revert the commit and try again
in a later release.
Fixes: 3dec89b14d37 ("net/ipv6: Remove expired routes with a separated list of routes") Cc: Kui-Feng Lee <thinker.li@gmail.com> Signed-off-by: David Ahern <dsahern@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231219030243.25687-1-dsahern@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 21 Dec 2023 07:34:08 +0000 (08:34 +0100)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-18 (ice)
This series contains updates to ice driver only.
Jakes stops clearing of needed aggregator information.
Dave adds a check for LAG device support before initializing the
associated event handler.
Larysa restores accounting of XDP queues in TC configurations.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix PF with enabled XDP going no-carrier after reset
ice: alter feature support check for SRIOV and LAG
ice: stop trashing VF VSI aggregator node ID information
====================
Thomas Weißschuh [Mon, 18 Dec 2023 17:06:54 +0000 (18:06 +0100)]
net: avoid build bug in skb extension length calculation
GCC seems to incorrectly fail to evaluate skb_ext_total_length() at
compile time under certain conditions.
The issue even occurs if all values in skb_ext_type_len[] are "0",
ruling out the possibility of an actual overflow.
As the patch has been in mainline since v6.6 without triggering the
problem it seems to be a very uncommon occurrence.
As the issue only occurs when -fno-tree-loop-im is specified as part of
CFLAGS_GCOV, disable the BUILD_BUG_ON() only when building with coverage
reporting enabled.
Linus Torvalds [Tue, 19 Dec 2023 23:26:59 +0000 (15:26 -0800)]
posix-timers: Get rid of [COMPAT_]SYS_NI() uses
Only the posix timer system calls use this (when the posix timer support
is disabled, which does not actually happen in any normal case), because
they had debug code to print out a warning about missing system calls.
Get rid of that special case, and just use the standard COND_SYSCALL
interface that creates weak system call stubs that return -ENOSYS for
when the system call does not exist.
This fixes a kCFI issue with the SYS_NI() hackery:
CFI failure at int80_emulation+0x67/0xb0 (target: sys_ni_posix_timers+0x0/0x70; expected type: 0xb02b34d9)
WARNING: CPU: 0 PID: 48 at int80_emulation+0x67/0xb0
Reported-by: kernel test robot <oliver.sang@intel.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 21 Dec 2023 05:09:47 +0000 (21:09 -0800)]
Merge tag '6.7-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two multichannel reconnect fixes, one fixing an important refcounting
problem that can lead to umount problems
- atime fix
- five fixes for various potential OOB accesses, including a CVE fix,
and two additional fixes for problems pointed out by Robert Morris's
fuzzing investigation
* tag '6.7-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: do not let cifs_chan_update_iface deallocate channels
cifs: fix a pending undercount of srv_count
fs: cifs: Fix atime update check
smb: client: fix potential OOB in smb2_dump_detail()
smb: client: fix potential OOB in cifs_dump_detail()
smb: client: fix OOB in smbCalcSize()
smb: client: fix OOB in SMB2_query_info_init()
smb: client: fix OOB in cifsd when receiving compounded resps
Linus Torvalds [Thu, 21 Dec 2023 00:06:40 +0000 (16:06 -0800)]
Merge tag 'soc-fixes-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only a handful of bugfixes this time, which feels almost too
small, so I hope we are not missing something important.
- One more mediatek dts warning fix after the previous larger set,
this should finally result in a clean defconfig build.
- TI OMAP dts fixes for a spurious hang on am335x and invalid data on
DTA7
- One DTS fix for ethernet on Oriange Pi Zero (Allwinner H616)
- A regression fix for ti-sysc interconnect target module driver to
not access registers after reset if srst_udelay quirk is needed
- Reset controller driver fixes for a crash during error handling and
a build warning"
* tag 'soc-fixes-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: mediatek: mt8395-genio-1200-evk: add interrupt-parent for mt6360
ARM: dts: Fix occasional boot hang for am3 usb
reset: Fix crash when freeing non-existent optional resets
ARM: OMAP2+: Fix null pointer dereference and memory leak in omap_soc_device_init
ARM: dts: dra7: Fix DRA7 L3 NoC node register size
bus: ti-sysc: Flush posted write only after srst_udelay
reset: hisilicon: hi6220: fix Wvoid-pointer-to-enum-cast warning
arm64: dts: allwinner: h616: update emac for Orange Pi Zero 3
Linus Torvalds [Wed, 20 Dec 2023 23:58:18 +0000 (15:58 -0800)]
Merge tag 'platform-drivers-x86-v6.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
- Fan reporting on some ThinkPads
- Laptop 13 spurious keypresses while suspended
- Intel PMC correction to avoid crash
* tag 'platform-drivers-x86-v6.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/pmc: Disable keyboard wakeup on AMD Framework 13
platform/x86/amd/pmc: Move keyboard wakeup disablement detection to pmc-quirks
platform/x86/amd/pmc: Only run IRQ1 firmware version check on Cezanne
platform/x86/amd/pmc: Move platform defines to header
platform/x86/intel/pmc: Fix hang in pmc_core_send_ltr_ignore()
platform/x86: thinkpad_acpi: fix for incorrect fan reporting on some ThinkPad systems
Linus Torvalds [Wed, 20 Dec 2023 20:04:03 +0000 (12:04 -0800)]
Merge tag 'ovl-fixes-6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fix from Amir Goldstein:
"Fix a regression from this merge window"
* tag 'ovl-fixes-6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix dentry reference leak after changes to underlying layers
Linus Torvalds [Wed, 20 Dec 2023 19:24:28 +0000 (11:24 -0800)]
Merge tag 'bcachefs-2023-12-19' of https://evilpiepirate.org/git/bcachefs
Pull more bcachefs fixes from Kent Overstreet:
- Fix a deadlock in the data move path with nocow locks (vs. update in
place writes); when trylock failed we were incorrectly waiting for in
flight ios to flush.
- Fix reporting of NFS file handle length
- Fix early error path in bch2_fs_alloc() - list head wasn't being
initialized early enough
- Make sure correct (hardware accelerated) crc modules get loaded
- Fix a rare overflow in the btree split path, when the packed bkey
format grows and all the keys have no value (LRU btree).
- Fix error handling in the sector allocator
This was causing writes to spuriously fail in multidevice setups, and
another bug meant that the errors weren't being logged, only reported
via fsync.
* tag 'bcachefs-2023-12-19' of https://evilpiepirate.org/git/bcachefs:
bcachefs: Fix bch2_alloc_sectors_start_trans() error handling
bcachefs; guard against overflow in btree node split
bcachefs: btree_node_u64s_with_format() takes nr keys
bcachefs: print explicit recovery pass message only once
bcachefs: improve modprobe support by providing softdeps
bcachefs: fix invalid memory access in bch2_fs_alloc() error path
bcachefs: Fix determining required file handle length
bcachefs: Fix nocow locks deadlock
Linus Torvalds [Wed, 20 Dec 2023 19:01:28 +0000 (11:01 -0800)]
Merge tag 'dm-6.7/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM raid target (and MD raid) fix for reconfig_mutex MD deadlock that
should have been merged along with recent v6.7-rc6 MD fixes (see MD
related commits: f2d87a759f68^..b39113349de6)
- DM integrity target fix to avoid modifying immutable biovec in the
integrity_metadata() edge case where kmalloc fails.
- Fix drivers/md/Kconfig so DM_AUDIT depends on BLK_DEV_DM.
- Update DM entry in MAINTAINERS to remove stale info.
* tag 'dm-6.7/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
MAINTAINERS: remove stale info for DEVICE-MAPPER
dm audit: fix Kconfig so DM_AUDIT depends on BLK_DEV_DM
dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
dm-raid: delay flushing event_work() after reconfig_mutex is released
netfilter: nf_tables: skip set commit for deleted/destroyed sets
NFT_MSG_DELSET deactivates all elements in the set, skip
set->ops->commit() to avoid the unnecessary clone (for the pipapo case)
as well as the sync GC cycle, which could deactivate again expired
elements in such set.
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane") Reported-by: Kevin Rich <kevinrich1337@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net: stmmac: fix incorrect flag check in timestamp interrupt
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag") Cc: <stable@vger.kernel.org> # 6.6 Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com> Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 Dec 2023 11:12:12 +0000 (11:12 +0000)]
Merge tag 'for-net-2023-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Add encryption key size check when acting as peripheral
- Shut up false-positive build warning
- Send reject if L2CAP command request is corrupted
- Fix Use-After-Free in bt_sock_recvmsg
- Fix not notifying when connection encryption changes
- Fix not checking if HCI_OP_INQUIRY has been sent
- Fix address type send over to the MGMT interface
- Fix deadlock in vhci_send_frame
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: set transport offset from mac header for netdev/egress
Before this patch, transport offset (pkt->thoff) provides an offset
relative to the network header. This is fine for the inet families
because skb->data points to the network header in such case. However,
from netdev/egress, skb->data points to the mac header (if available),
thus, pkt->thoff is missing the mac header length.
Add skb_network_offset() to the transport offset (pkt->thoff) for
netdev, so transport header mangling works as expected. Adjust payload
fast eval function to use skb->data now that pkt->thoff provides an
absolute offset. This explains why users report that matching on
egress/netdev works but payload mangling does not.
This patch implicitly fixes payload mangling for IPv4 packets in
netdev/egress given skb_store_bits() requires an offset from skb->data
to reach the transport header.
I suspect that nft_exthdr and the trace infra were also broken from
netdev/egress because they also take skb->data as start, and pkt->thoff
was not correct.
Note that IPv6 is fine because ipv6_find_hdr() already provides a
transport offset starting from skb->data, which includes
skb_network_offset().
The bridge family also uses nft_set_pktinfo_ipv4_validate(), but there
skb_network_offset() is zero, so the update in this patch does not alter
the existing behaviour.
When we fail to allocate because of insufficient open buckets, we don't
want to retry from the full set of devices - we just want to retry in
blocking mode.
But if the retry in blocking mode fails with a different error code, we
end up squashing the -BCH_ERR_open_buckets_empty error with an error
that makes us thing we won't be able to allocate (insufficient_devices)
- which is incorrect when we didn't try to allocate from the full set of
devices, and causes the write to fail.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Linus Torvalds [Tue, 19 Dec 2023 20:25:43 +0000 (12:25 -0800)]
Merge tag 'trace-v6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
"While working on the ring buffer, I found one more bug with the
timestamp code, and the fix for this removed the need for the final
64-bit cmpxchg!
The ring buffer events hold a "delta" from the previous event. If it
is determined that the delta can not be calculated, it falls back to
adding an absolute timestamp value. The way to know if the delta can
be used is via two stored timestamps in the per-cpu buffer meta data:
before_stamp and write_stamp
The before_stamp is written by every event before it tries to allocate
its space on the ring buffer. The write_stamp is written after it
allocates its space and knows that nothing came in after it read the
previous before_stamp and write_stamp and the two matched.
A previous fix dd9394257078 ("ring-buffer: Do not try to put back
write_stamp") removed putting back the write_stamp to match the
before_stamp so that the next event could use the delta, but races
were found where the two would match, but not be for of the previous
event.
It was determined to allow the event reservation to not have a valid
write_stamp when it is finished, and this fixed a lot of races.
The last use of the 64-bit timestamp cmpxchg depended on the
write_stamp being valid after an interruption. But this is no longer
the case, as if an event is interrupted by a softirq that writes an
event, and that event gets interrupted by a hardirq or NMI and that
writes an event, then the softirq could finish its reservation without
a valid write_stamp.
In the slow path of the event reservation, a delta can still be used
if the write_stamp is valid. Instead of using a cmpxchg against the
write stamp, the before_stamp needs to be read again to validate the
write_stamp. The cmpxchg is not needed.
This updates the slowpath to validate the write_stamp by comparing it
to the before_stamp and removes all rb_time_cmpxchg() as there are no
more users of that function.
The removal of the 32-bit updates of rb_time_t will be done in the
next merge window"
* tag 'trace-v6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Fix slowpath of interrupted event
Linus Torvalds [Tue, 19 Dec 2023 20:19:25 +0000 (12:19 -0800)]
Merge tag 'arc-6.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- build error for hugetlb, sparse and smatch fixes
- removal of VIPT aliasing cache code
* tag 'arc-6.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: add hugetlb definitions
ARC: fix smatch warning
ARC: fix spare error
ARC: mm: retire support for aliasing VIPT D$
ARC: entry: move ARCompact specific bits out of entry.h
ARC: entry: SAVE_ABI_CALLEE_REG: ISA/ABI specific helper
Shyam Prasad N [Fri, 15 Dec 2023 17:16:56 +0000 (17:16 +0000)]
cifs: do not let cifs_chan_update_iface deallocate channels
cifs_chan_update_iface is meant to check and update the server
interface used for a channel when the existing server interface
is no longer available.
So far, this handler had the code to remove an interface entry
even if a new candidate interface is not available. Allowing
this leads to several corner cases to handle.
This change makes the logic much simpler by not deallocating
the current channel interface entry if a new interface is not
found to replace it with.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Shyam Prasad N [Fri, 15 Dec 2023 17:16:55 +0000 (17:16 +0000)]
cifs: fix a pending undercount of srv_count
The following commit reverted the changes to ref count
the server struct while scheduling a reconnect work: 823342524868 Revert "cifs: reconnect work should have reference on server struct"
However, a following change also introduced scheduling
of reconnect work, and assumed ref counting. This change
fixes that as well.
Reported-by: Robert Morris <rtm@csail.mit.edu> Fixes: 705fc522fe9d ("cifs: handle when server starts supporting multichannel") Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Zizhi Wo [Wed, 13 Dec 2023 02:23:53 +0000 (10:23 +0800)]
fs: cifs: Fix atime update check
Commit 9b9c5bea0b96 ("cifs: do not return atime less than mtime") indicates
that in cifs, if atime is less than mtime, some apps will break.
Therefore, it introduce a function to compare this two variables in two
places where atime is updated. If atime is less than mtime, update it to
mtime.
However, the patch was handled incorrectly, resulting in atime and mtime
being exactly equal. A previous commit 69738cfdfa70 ("fs: cifs: Fix atime
update check vs mtime") fixed one place and forgot to fix another. Fix it.
Fixes: 9b9c5bea0b96 ("cifs: do not return atime less than mtime") Cc: stable@vger.kernel.org Signed-off-by: Zizhi Wo <wozizhi@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara [Tue, 19 Dec 2023 16:10:31 +0000 (13:10 -0300)]
smb: client: fix potential OOB in smb2_dump_detail()
Validate SMB message with ->check_message() before calling
->calc_smb_size().
This fixes CVE-2023-6610.
Reported-by: j51569436@gmail.com Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218219
Cc; stable@vger.kernel.org Signed-off-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Liu Jian [Sat, 16 Dec 2023 07:52:18 +0000 (15:52 +0800)]
net: check vlan filter feature in vlan_vids_add_by_dev() and vlan_vids_del_by_dev()
I got the below warning trace:
WARNING: CPU: 4 PID: 4056 at net/core/dev.c:11066 unregister_netdevice_many_notify
CPU: 4 PID: 4056 Comm: ip Not tainted 6.7.0-rc4+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:unregister_netdevice_many_notify+0x9a4/0x9b0
Call Trace:
rtnl_dellink
rtnetlink_rcv_msg
netlink_rcv_skb
netlink_unicast
netlink_sendmsg
__sock_sendmsg
____sys_sendmsg
___sys_sendmsg
__sys_sendmsg
do_syscall_64
entry_SYSCALL_64_after_hwframe
It can be repoduced via:
ip netns add ns1
ip netns exec ns1 ip link add bond0 type bond mode 0
ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
ip netns exec ns1 ip link set bond_slave_1 master bond0
[1] ip netns exec ns1 ethtool -K bond0 rx-vlan-filter off
[2] ip netns exec ns1 ip link add link bond_slave_1 name bond_slave_1.0 type vlan id 0
[3] ip netns exec ns1 ip link add link bond0 name bond0.0 type vlan id 0
[4] ip netns exec ns1 ip link set bond_slave_1 nomaster
[5] ip netns exec ns1 ip link del veth2
ip netns del ns1
This is all caused by command [1] turning off the rx-vlan-filter function
of bond0. The reason is the same as commit 01f4fd270870 ("bonding: Fix
incorrect deletion of ETH_P_8021AD protocol vid from slaves"). Commands
[2] [3] add the same vid to slave and master respectively, causing
command [4] to empty slave->vlan_info. The following command [5] triggers
this problem.
To fix this problem, we should add VLAN_FILTER feature checks in
vlan_vids_add_by_dev() and vlan_vids_del_by_dev() to prevent incorrect
addition or deletion of vlan_vid information.
Fixes: 348a1443cc43 ("vlan: introduce functions to do mass addition/deletion of vids by another device") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Benjamin Berg [Wed, 20 Dec 2023 02:38:01 +0000 (04:38 +0200)]
wifi: mac80211: add/remove driver debugfs entries as appropriate
When an interface is removed, we should also be deleting the driver
debugfs entries (as it might still exist in DOWN state in mac80211). At
the same time, when adding an interface, we can check the
IEEE80211_SDATA_IN_DRIVER flag to know whether the interface was
previously known to the driver and is simply being reconfigured.
Fixes: a1f5dcb1c0c1 ("wifi: mac80211: add a driver callback to add vif debugfs") Signed-off-by: Benjamin Berg <benjamin.berg@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20231220043149.a9f64c359424.I7076526b5297ae8f832228079c999f7b8e147a4c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Benjamin Berg [Wed, 20 Dec 2023 02:38:00 +0000 (04:38 +0200)]
wifi: mac80211: do not re-add debugfs entries during resume
The driver debugfs entries still exist when the interface is re-added
during reconfiguration. This can be either because of a HW restart
(in_reconfig) or because we are resuming.
Fixes: a1f5dcb1c0c1 ("wifi: mac80211: add a driver callback to add vif debugfs") Signed-off-by: Benjamin Berg <benjamin.berg@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20231220043149.ddd48c66ec6b.Ia81080d92129ceecf462eceb4966bab80df12060@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ronald Wahl [Thu, 14 Dec 2023 18:11:12 +0000 (19:11 +0100)]
net: ks8851: Fix TX stall caused by TX buffer overrun
There is a bug in the ks8851 Ethernet driver that more data is written
to the hardware TX buffer than actually available. This is caused by
wrong accounting of the free TX buffer space.
The driver maintains a tx_space variable that represents the TX buffer
space that is deemed to be free. The ks8851_start_xmit_spi() function
adds an SKB to a queue if tx_space is large enough and reduces tx_space
by the amount of buffer space it will later need in the TX buffer and
then schedules a work item. If there is not enough space then the TX
queue is stopped.
The worker function ks8851_tx_work() dequeues all the SKBs and writes
the data into the hardware TX buffer. The last packet will trigger an
interrupt after it was send. Here it is assumed that all data fits into
the TX buffer.
In the interrupt routine (which runs asynchronously because it is a
threaded interrupt) tx_space is updated with the current value from the
hardware. Also the TX queue is woken up again.
Now it could happen that after data was sent to the hardware and before
handling the TX interrupt new data is queued in ks8851_start_xmit_spi()
when the TX buffer space had still some space left. When the interrupt
is actually handled tx_space is updated from the hardware but now we
already have new SKBs queued that have not been written to the hardware
TX buffer yet. Since tx_space has been overwritten by the value from the
hardware the space is not accounted for.
Now we have more data queued then buffer space available in the hardware
and ks8851_tx_work() will potentially overrun the hardware TX buffer. In
many cases it will still work because often the buffer is written out
fast enough so that no overrun occurs but for example if the peer
throttles us via flow control then an overrun may happen.
This can be fixed in different ways. The most simple way would be to set
tx_space to 0 before writing data to the hardware TX buffer preventing
the queuing of more SKBs until the TX interrupt has been handled. I have
chosen a slightly more efficient (and still rather simple) way and
track the amount of data that is already queued and not yet written to
the hardware. When new SKBs are to be queued the already queued amount
of data is honoured when checking free TX buffer space.
I tested this with a setup of two linked KS8851 running iperf3 between
the two in bidirectional mode. Before the fix I got a stall after some
minutes. With the fix I saw now issues anymore after hours.
Fixes: 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver") Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org # 5.10+ Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231214181112.76052-1-rwahl@gmx.de Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To synchronize the timestamps with the ring buffer reservation, there are
two timestamps that are saved in the buffer meta data.
1. before_stamp
2. write_stamp
When the two are equal, the write_stamp is considered valid, as in, it may
be used to calculate the delta of the next event as the write_stamp is the
timestamp of the previous reserved event on the buffer.
This is done by the following:
/*A*/ w = current position on the ring buffer
before = before_stamp
after = write_stamp
ts = read current timestamp
if (before != after) {
write_stamp is not valid, force adding an absolute
timestamp.
}
/*B*/ before_stamp = ts
/*C*/ write = local_add_return(event length, position on ring buffer)
if (w == write - event length) {
/* Nothing interrupted between A and C */
/*E*/ write_stamp = ts;
delta = ts - after
/*
* If nothing interrupted again,
* before_stamp == write_stamp and write_stamp
* can be used to calculate the delta for
* events that come in after this one.
*/
} else {
/*
* The slow path!
* Was interrupted between A and C.
*/
This is the place that there's a bug. We currently have:
after = write_stamp
ts = read current timestamp
/*F*/ if (write == current position on the ring buffer &&
after < ts && cmpxchg(write_stamp, after, ts)) {
delta = ts - after;
} else {
delta = 0;
}
The assumption is that if the current position on the ring buffer hasn't
moved between C and F, then it also was not interrupted, and that the last
event written has a timestamp that matches the write_stamp. That is the
write_stamp is valid.
But this may not be the case:
If a task context event was interrupted by softirq between B and C.
And the softirq wrote an event that got interrupted by a hard irq between
C and E.
and the hard irq wrote an event (does not need to be interrupted)
We have:
/*B*/ before_stamp = ts of normal context
---> interrupted by softirq
/*B*/ before_stamp = ts of softirq context
---> interrupted by hardirq
/*B*/ before_stamp = ts of hard irq context
/*E*/ write_stamp = ts of hard irq context
/* matches and write_stamp valid */
<----
/*E*/ write_stamp = ts of softirq context
/* No longer matches before_stamp, write_stamp is not valid! */
<---
w != write - length, go to slow path
// Right now the order of events in the ring buffer is:
//
// |-- softirq event --|-- hard irq event --|-- normal context event --|
//
after = write_stamp (this is the ts of softirq)
ts = read current timestamp
if (write == current position on the ring buffer [true] &&
after < ts [true] && cmpxchg(write_stamp, after, ts) [true]) {
delta = ts - after [Wrong!]
The delta is to be between the hard irq event and the normal context
event, but the above logic made the delta between the softirq event and
the normal context event, where the hard irq event is between the two. This
will shift all the remaining event timestamps on the sub-buffer
incorrectly.
The write_stamp is only valid if it matches the before_stamp. The cmpxchg
does nothing to help this.
Instead, the following logic can be done to fix this:
before = before_stamp
ts = read current timestamp
before_stamp = ts
after = write_stamp
if (write == current position on the ring buffer &&
after == before && after < ts) {
delta = ts - after
} else {
delta = 0;
}
The above will only use the write_stamp if it still matches before_stamp
and was tested to not have changed since C.
As a bonus, with this logic we do not need any 64-bit cmpxchg() at all!
This means the 32-bit rb_time_t workaround can finally be removed. But
that's for a later time.
Linus Torvalds [Tue, 19 Dec 2023 00:47:21 +0000 (16:47 -0800)]
Merge tag 'hid-for-linus-2023121901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- fix for division by zero in Nintendo driver when generic joycon is
attached, reported and fixed by SteamOS folks (Guilherme G. Piccoli)
- GCC-7 build fix (which is a good cleanup anyway) for Nintendo driver
(Ryan McClelland)
* tag 'hid-for-linus-2023121901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: nintendo: Prevent divide-by-zero on code
HID: nintendo: fix initializer element is not constant error
Guillaume says:
> I believe commit 5f7fc5d69f6e ("SUNRPC: Resupply rq_pages from
> node-local memory") in Linux 6.5+ is incorrect. It passes
> unconditionally rq_pool->sp_id as the NUMA node.
>
> While the comment in the svc_pool declaration in sunrpc/svc.h says
> that sp_id is also the NUMA node id, it might not be the case if
> the svc is created using svc_create_pooled(). svc_created_pooled()
> can use the per-cpu pool mode therefore in this case sp_id would
> be the cpu id.
Fix this by reverting now. At a later point this minor optimization,
and the deceptive labeling of the sp_id field, can be revisited.
Reported-by: Guillaume Morin <guillaume@morinfr.org> Closes: https://lore.kernel.org/linux-nfs/ZYC9rsno8qYggVt9@bender.morinfr.org/T/#u Fixes: 5f7fc5d69f6e ("SUNRPC: Resupply rq_pages from node-local memory") Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Since it's a divide-by-0 error, by tracking the code for potential
denominator issues, we've spotted 2 places in which this could happen;
so let's guard against the possibility and log in the kernel if the
condition happens. This is specially useful since some data that
fills some denominators are read from the joycon HW in some cases,
increasing the potential for flaws.
Linus Torvalds [Mon, 18 Dec 2023 19:11:09 +0000 (11:11 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two medium sized fixes, both in drivers.
The UFS one adds parsing of clock info structures, which is required
by some host drivers and the aacraid one reverts the IRQ affinity
mapping patch which has been causing regressions noted in kernel
bugzilla 217599"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Store min and max clk freq from OPP table
Revert "scsi: aacraid: Reply queue mapping to CPUs based on IRQ affinity"
Linus Torvalds [Mon, 18 Dec 2023 18:59:57 +0000 (10:59 -0800)]
Merge tag 'spi-fix-v6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few bigger things here, the main one being that there were changes
to the atmel driver in this cycle which made it possible to kill
transfers being used for filesystem I/O which turned out to be very
disruptive, the series of patches here undoes that and hardens things
up further.
There's also a few smaller driver specific changes, the main one being
to revert a change that duplicted delays"
* tag 'spi-fix-v6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix clock issue when using devices with different polarities
spi: spi-imx: correctly configure burst length when using dma
spi: cadence: revert "Add SPI transfer delays"
spi: atmel: Prevent spi transfers from being killed
spi: atmel: Drop unused defines
spi: atmel: Do not cancel a transfer upon any signal
Mikulas Patocka [Tue, 5 Dec 2023 15:39:16 +0000 (16:39 +0100)]
dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
__bio_for_each_segment assumes that the first struct bio_vec argument
doesn't change - it calls "bio_advance_iter_single((bio), &(iter),
(bvl).bv_len)" to advance the iterator. Unfortunately, the dm-integrity
code changes the bio_vec with "bv.bv_len -= pos". When this code path
is taken, the iterator would be out of sync and dm-integrity would
report errors. This happens if the machine is out of memory and
"kmalloc" fails.
Fix this bug by making a copy of "bv" and changing the copy instead.
Yu Kuai [Fri, 24 Nov 2023 07:59:53 +0000 (15:59 +0800)]
dm-raid: delay flushing event_work() after reconfig_mutex is released
After commit db5e653d7c9f ("md: delay choosing sync action to
md_start_sync()"), md_start_sync() will hold 'reconfig_mutex', however,
in order to make sure event_work is done, __md_stop() will flush
workqueue with reconfig_mutex grabbed, hence if sync_work is still
pending, deadlock will be triggered.
Fortunately, former pacthes to fix stopping sync_thread already make sure
all sync_work is done already, hence such deadlock is not possible
anymore. However, in order not to cause confusions for people by this
implicit dependency, delay flushing event_work to dm-raid where
'reconfig_mutex' is not held, and add some comments to emphasize that
the workqueue can't be flushed with 'reconfig_mutex'.
Fixes: db5e653d7c9f ("md: delay choosing sync action to md_start_sync()")
Depends-on: f52f5c71f3d4 ("md: fix stopping sync thread") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Xiao Ni <xni@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Larysa Zaremba [Tue, 12 Dec 2023 09:29:01 +0000 (10:29 +0100)]
ice: Fix PF with enabled XDP going no-carrier after reset
Commit 6624e780a577fc596788 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.
Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:
ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Dave Ertman [Mon, 11 Dec 2023 21:19:28 +0000 (13:19 -0800)]
ice: alter feature support check for SRIOV and LAG
Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time. While this was still in place, additional
support was added to specifically support SRIOV and LAG together. These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.
The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.
Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support. This will leave other systems unhindered with
functionality as it existed before any LAG code was added.
Fixes: bb52f42acef6 ("ice: Add driver support for firmware changes for LAG") Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Wed, 6 Dec 2023 20:19:05 +0000 (12:19 -0800)]
ice: stop trashing VF VSI aggregator node ID information
When creating new VSIs, they are assigned into an aggregator node in the
scheduler tree. Information about which aggregator node a VSI is assigned
into is maintained by the vsi->agg_node structure. In ice_vsi_decfg(), this
information is being destroyed, by overwriting the valid flag and the
agg_id field to zero.
For VF VSIs, this breaks the aggregator node configuration replay, which
depends on this information. This results in VFs being inserted into the
default aggregator node. The resulting configuration will have unexpected
Tx bandwidth sharing behavior.
This was broken by commit 6624e780a577 ("ice: split ice_vsi_setup into
smaller functions"), which added the block to reset the agg_node data.
The vsi->agg_node structure is not managed by the scheduler code, but is
instead a wrapper around an aggregator node ID that is tracked at the VSI
layer. Its been around for a long time, and its primary purpose was for
handling VFs. The SR-IOV VF reset flow does not make use of the standard VSI
rebuild/replay logic, and uses vsi->agg_node as part of its handling to
rebuild the aggregator node configuration.
The logic for aggregator nodes stretches back to early ice driver code from
commit b126bd6bcd67 ("ice: create scheduler aggregator node config and move
VSIs")
The logic in ice_vsi_decfg() which trashes the ice_agg_node data is clearly
wrong. It destroys information that is necessary for handling VF reset,. It
is also not the correct way to actually remove a VSI from an aggregator
node. For that, we need to implement logic in the scheduler code. Further,
non-VF VSIs properly replay their aggregator configuration using existing
scheduler replay logic.
To fix the VF replay logic, remove this broken aggregator node cleanup
logic. This is the simplest way to immediately fix this.
This ensures that VFs will have proper aggregate configuration after a
reset. This is especially important since VFs often perform resets as part
of their reconfiguration flows. Without fixing this, VFs will be placed in
the default aggregator node and Tx bandwidth will not be shared in the
expected and configured manner.
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Johannes Berg [Fri, 15 Dec 2023 10:13:34 +0000 (11:13 +0100)]
wifi: iwlwifi: pcie: don't synchronize IRQs from IRQ
On older devices (before unified image!) we can end up calling
stop_device from an rfkill interrupt. However, in stop_device
we attempt to synchronize IRQs, which then of course deadlocks.
Avoid this by checking the context, if running from the IRQ
thread then don't synchronize. This wouldn't be correct on a
new device since RSS is supported, but older devices only have
a single interrupt/queue.
Fixes: 37fb29bd1f90 ("wifi: iwlwifi: pcie: synchronize IRQs before NAPI") Reviewed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20231215111335.59aab00baed7.Iadfe154d6248e7f9dfd69522e5429dbbd72925d7@changeid
There's nothing wrong with this commit, but this is dead code now
that nothing triggers a CB_GETATTR callback. It can be re-introduced
once the issues with handling conflicting GETATTRs are resolved.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
For some reason, the wait_on_bit() in nfsd4_deleg_getattr_conflict()
is waiting forever, preventing a clean server shutdown. The
requesting client might also hang waiting for a reply to the
conflicting GETATTR.
Invoking wait_on_bit() in an nfsd thread context is a hazard. The
correct fix is to replace this wait_on_bit() call site with a
mechanism that defers the conflicting GETATTR until the CB_GETATTR
completes or is known to have failed.
That will require some surgery and extended testing and it's late
in the v6.7-rc cycle, so I'm reverting now in favor of trying again
in a subsequent kernel release.
This is my fault: I should have recognized the ramifications of
calling wait_on_bit() in here before accepting this patch.
Thanks to Dai Ngo <dai.ngo@oracle.com> for diagnosing the issue.
Reported-by: Wolfgang Walter <linux-nfs@stwm.de> Closes: https://lore.kernel.org/linux-nfs/e3d43ecdad554fbdcaa7181833834f78@stwm.de/ Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
platform/x86/amd/pmc: Disable keyboard wakeup on AMD Framework 13
The Laptop 13 (AMD Ryzen 7040Series) BIOS 03.03 has a workaround
included in the EC firmware that will cause the EC to emit a "spurious"
keypress during the resume from s0i3 [1].
This series of keypress events can be observed in the kernel log on
resume.
```
atkbd serio0: Unknown key pressed (translated set 2, code 0x6b on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 6b <keycode>' to make it known.
atkbd serio0: Unknown key released (translated set 2, code 0x6b on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 6b <keycode>' to make it known.
```
In some user flows this is harmless, but if a user has specifically
suspended the laptop and then closed the lid it will cause the laptop
to wakeup. The laptop wakes up because the ACPI SCI triggers when
the lid is closed and when the kernel sees that IRQ1 is "also" active.
The kernel can't distinguish from a real keyboard keypress and wakes the
system.
Add the model into the list of quirks to disable keyboard wakeup source.
This is intentionally only matching the production BIOS version in hopes
that a newer EC firmware included in a newer BIOS can avoid this behavior.
platform/x86/amd/pmc: Move keyboard wakeup disablement detection to pmc-quirks
Other platforms may need to disable keyboard wakeup besides Cezanne,
so move the detection into amd_pmc_quirks_init() where it may be applied
to multiple platforms.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20231212045006.97581-4-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86/amd/pmc: Only run IRQ1 firmware version check on Cezanne
amd_pmc_wa_czn_irq1() only runs on Cezanne platforms currently but
may be extended to other platforms in the future. Rename the function
and only check platform firmware version when it's called for a Cezanne
based platform.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20231212045006.97581-3-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86/amd/pmc: Move platform defines to header
The platform defines will be used by the quirks in the future,
so move them to the common header to allow use by both source
files.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20231212045006.97581-2-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Rajvi Jingar [Sat, 16 Dec 2023 01:16:50 +0000 (17:16 -0800)]
platform/x86/intel/pmc: Fix hang in pmc_core_send_ltr_ignore()
For input value 0, PMC stays unassigned which causes crash while trying
to access PMC for register read/write. Include LTR index 0 in pmc_index
and ltr_index calculation.
Vishnu Sankar [Thu, 14 Dec 2023 13:47:02 +0000 (22:47 +0900)]
platform/x86: thinkpad_acpi: fix for incorrect fan reporting on some ThinkPad systems
Some ThinkPad systems ECFW use non-standard addresses for fan control
and reporting. This patch adds support for such ECFW so that it can report
the correct fan values.
Tested on Thinkpads L13 Yoga Gen 2 and X13 Yoga Gen 2.
Suggested-by: Mark Pearson <mpearson-lenovo@squebb.ca> Signed-off-by: Vishnu Sankar <vishnuocv@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20231214134702.166464-1-vishnuocv@gmail.com Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Heiko Carstens [Fri, 8 Dec 2023 14:03:15 +0000 (15:03 +0100)]
s390/vx: fix save/restore of fpu kernel context
The KERNEL_FPR mask only contains a flag for the first eight vector
registers. However floating point registers overlay parts of the first
sixteen vector registers.
This could lead to vector register corruption if a kernel fpu context uses
any of the vector registers 8 to 15 and is interrupted or calls a
KERNEL_FPR context. If that context uses also vector registers 8 to 15,
their contents will be corrupted on return.
Luckily this is currently not a real bug, since the kernel has only one
KERNEL_FPR user with s390_adjust_jiffies() and it is only using floating
point registers 0 to 2.
Fix this by using the correct bits for KERNEL_FPR.
Fixes: 7f79695cc1b6 ("s390/fpu: improve kernel_fpu_[begin|end]") Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Ryan McClelland [Thu, 14 Dec 2023 17:25:41 +0000 (09:25 -0800)]
HID: nintendo: fix initializer element is not constant error
With gcc-7 builds, an error happens with the controller button values being
defined as const. Change to a define.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312141227.C2h1IzfI-lkp@intel.com/ Signed-off-by: Ryan McClelland <rymcclel@gmail.com> Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
Reported-by: j51569436@gmail.com Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218218 Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara [Wed, 13 Dec 2023 15:25:57 +0000 (12:25 -0300)]
smb: client: fix OOB in SMB2_query_info_init()
A small CIFS buffer (448 bytes) isn't big enough to hold
SMB2_QUERY_INFO request along with user's input data from
CIFS_QUERY_INFO ioctl. That is, if the user passed an input buffer >
344 bytes, the client will memcpy() off the end of @req->Buffer in
SMB2_query_info_init() thus causing the following KASAN splat:
BUG: KASAN: slab-out-of-bounds in SMB2_query_info_init+0x242/0x250 [cifs]
Write of size 1023 at addr ffff88801308c5a8 by task a.out/1240
Fix this by increasing size of SMB2_QUERY_INFO request buffers and
validating input length to prevent other callers from overflowing @req
in SMB2_query_info_init() as well.
Fixes: f5b05d622a3e ("cifs: add IOCTL for QUERY_INFO passthrough to userspace") Cc: stable@vger.kernel.org Reported-by: Robert Morris <rtm@csail.mit.edu> Signed-off-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara [Wed, 13 Dec 2023 15:25:56 +0000 (12:25 -0300)]
smb: client: fix OOB in cifsd when receiving compounded resps
Validate next header's offset in ->next_header() so that it isn't
smaller than MID_HEADER_SIZE(server) and then standard_receive3() or
->receive() ends up writing off the end of the buffer because
'pdu_length - MID_HEADER_SIZE(server)' wraps up to a huge length:
BUG: KASAN: slab-out-of-bounds in _copy_to_iter+0x4fc/0x840
Write of size 701 at addr ffff88800caf407f by task cifsd/1090
Fixes: 8ce79ec359ad ("cifs: update multiplex loop to handle compounded responses") Cc: stable@vger.kernel.org Reported-by: Robert Morris <rtm@csail.mit.edu> Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
David S. Miller [Sun, 17 Dec 2023 20:54:22 +0000 (20:54 +0000)]
Merge branch 'mptcp-misc-fixes'
Matthieu Baerts says:
====================
mptcp: misc. fixes for v6.7
Here are a few fixes related to MPTCP:
Patch 1 avoids skipping some subtests of the MPTCP Join selftest by
mistake when using older versions of GCC. This fixes a patch introduced
in v6.4, backported up to v6.1.
Patch 2 fixes an inconsistent state when using MPTCP + FastOpen. A fix
for v6.2.
Patch 3 adds a description for MPTCP Kunit test modules to avoid a
warning.
Patch 4 adds an entry to the mailmap file for Geliang's email addresses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Matthieu Baerts [Fri, 15 Dec 2023 16:04:26 +0000 (17:04 +0100)]
mptcp: fill in missing MODULE_DESCRIPTION()
W=1 builds warn on missing MODULE_DESCRIPTION, add them here in MPTCP.
Only two were missing: two modules with different KUnit tests for MPTCP.
Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
and transitioning such subflow to FIN_WAIT1 status before the syn-ack
packet is processed. The MPTCP code does not react to such state change,
leaving the connection in not-fallback status and the subflow handshake
uncompleted, triggering the following splat:
To address the issue, catch the racing subflow state change and
use it to cause the MPTCP fallback. Such fallback is also used to
cause the first subflow state propagation to the msk socket via
mptcp_set_connected(). After this change, the first subflow can
additionally propagate the TCP_FIN_WAIT1 state, so rename the
helper accordingly.
Finally, if the state propagation is delayed to the msk release
callback, the first subflow can change to a different state in between.
Cache the relevant target state in a new msk-level field and use
such value to update the msk state at release time.
Fixes: 1e777f39b4d7 ("mptcp: add MSG_FASTOPEN sendmsg flag support") Cc: stable@vger.kernel.org Reported-by: <syzbot+c53d4d3ddb327e80bc51@syzkaller.appspotmail.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/458 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
MPC backups tests will skip unexpected sometimes (For example, when
compiling kernel with an older version of gcc, such as gcc-8), since
static functions like mptcp_subflow_send_ack also be listed in
/proc/kallsyms, with a 't' in front of it, not 'T' ('T' is for a global
function):
In this case, mptcp_lib_kallsyms_doesnt_have "mptcp_subflow_send_ack$"
will be false, MPC backups tests will skip. This is not what we expected.
The correct logic here should be: if mptcp_subflow_send_ack is not a
global function in /proc/kallsyms, do these MPC backups tests. So a 'T'
must be added in front of mptcp_subflow_send_ack.
Fixes: 632978f0a961 ("selftests: mptcp: join: skip MPC backups tests if not supported") Cc: stable@vger.kernel.org Signed-off-by: Geliang Tang <geliang.tang@linux.dev> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 17 Dec 2023 17:27:36 +0000 (09:27 -0800)]
Merge tag 'for-6.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix that verifies that the snapshot source is a root, same
check is also done in user space but should be done by the ioctl as
well"
* tag 'for-6.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: do not allow non subvolume root targets for snapshot
Linus Torvalds [Sun, 17 Dec 2023 17:24:06 +0000 (09:24 -0800)]
Merge tag 'soundwire-6.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fixes from Vinod Koul:
- Null pointer dereference for mult link in core
- AC timing fix in intel driver
* tag 'soundwire-6.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: intel_ace2x: fix AC timing setting for ACE2.x
soundwire: stream: fix NULL pointer dereference for multi_link
Linus Torvalds [Sun, 17 Dec 2023 17:19:27 +0000 (09:19 -0800)]
Merge tag 'phy-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy fixes from Vinod Koul:
- register offset fix for TI driver
- mediatek driver minimal supported frequency fix
- negative error code in probe fix for sunplus driver
* tag 'phy-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: sunplus: return negative error code in sp_usb_phy_probe
phy: mediatek: mipi: mt8183: fix minimal supported frequency
phy: ti: gmii-sel: Fix register offset when parent is not a syscon node
Linus Torvalds [Sun, 17 Dec 2023 17:11:32 +0000 (09:11 -0800)]
Merge tag 'dmaengine-fix-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
- SPI PDMA data fix for TI k3-psil drivers
- suspend fix, pointer check, logic for arbitration fix and channel
leak fix in fsl-edma driver
- couple of fixes in idxd driver for GRPCFG descriptions and int_handle
field handling
- single fix for stm32 driver for bitfield overflow
* tag 'dmaengine-fix-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: fsl-edma: fix DMA channel leak in eDMAv4
dmaengine: fsl-edma: fix wrong pointer check in fsl_edma3_attach_pd()
dmaengine: idxd: Fix incorrect descriptions for GRPCFG register
dmaengine: idxd: Protect int_handle field in hw descriptor
dmaengine: stm32-dma: avoid bitfield overflow assertion
dmaengine: fsl-edma: Add judgment on enabling round robin arbitration
dmaengine: fsl-edma: Do not suspend and resume the masked dma channel when the system is sleeping
dmaengine: ti: k3-psil-am62a: Fix SPI PDMA data
dmaengine: ti: k3-psil-am62: Fix SPI PDMA data
Linus Torvalds [Sun, 17 Dec 2023 17:07:34 +0000 (09:07 -0800)]
Merge tag 'cxl-fixes-6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL (Compute Express Link) fixes from Dan Williams:
"A collection of CXL fixes.
The touch outside of drivers/cxl/ is for a helper that allocates
physical address space. Device hotplug tests showed that the driver
failed to utilize (skipped over) valid capacity when allocating a new
memory region. Outside of that, new tests uncovered a small crop of
lockdep reports.
There is also some miscellaneous error path and leak fixups that are
not urgent, but useful to cleanup now.
- Fix put_device() like for the new CXL PMU driver
- Fix wrong pointer freed on error path
- Fixup several lockdep reports (missing lock hold) from new
assertion in cxl_num_decoders_committed() and new tests"
* tag 'cxl-fixes-6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/pmu: Ensure put_device on pmu devices
cxl/cdat: Free correct buffer on checksum error
cxl/hdm: Fix dpa translation locking
kernel/resource: Increment by align value in get_free_mem_region()
cxl: Add cxl_num_decoders_committed() usage to cxl_test
cxl/memdev: Hold region_rwsem during inject and clear poison ops
cxl/core: Always hold region_rwsem while reading poison lists
cxl/hdm: Fix a benign lockdep splat
Linus Torvalds [Sun, 17 Dec 2023 17:02:20 +0000 (09:02 -0800)]
Merge tag 'edac_urgent_for_v6.7_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
- A single fix for the EDAC Versal driver to read out register fields
properly
* tag 'edac_urgent_for_v6.7_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/versal: Read num_csrows and num_chans using the correct bitfield macro
Linus Torvalds [Sun, 17 Dec 2023 16:50:00 +0000 (08:50 -0800)]
Merge tag 'powerpc-6.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a bug where heavy VAS (accelerator) usage could race with
partition migration and prevent the migration from completing.
- Update MAINTAINERS to add Aneesh & Naveen.
Thanks to Haren Myneni.
* tag 'powerpc-6.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
MAINTAINERS: powerpc: Add Aneesh & Naveen
powerpc/pseries/vas: Migration suspend waits for no in-progress open windows
Amir Goldstein [Sun, 17 Dec 2023 09:08:52 +0000 (11:08 +0200)]
ovl: fix dentry reference leak after changes to underlying layers
syzbot excercised the forbidden practice of moving the workdir under
lowerdir while overlayfs is mounted and tripped a dentry reference leak.
Fixes: c63e56a4a652 ("ovl: do not open/llseek lower file with upper sb_writers held") Reported-and-tested-by: syzbot+8608bb4553edb8c78f41@syzkaller.appspotmail.com Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Linus Torvalds [Sat, 16 Dec 2023 18:40:51 +0000 (10:40 -0800)]
Merge tag 'trace-v6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix eventfs to check creating new files for events with names greater
than NAME_MAX. The eventfs lookup needs to check the return result of
simple_lookup().
- Fix the ring buffer to check the proper max data size. Events must be
able to fit on the ring buffer sub-buffer, if it cannot, then it
fails to be written and the logic to add the event is avoided. The
code to check if an event can fit failed to add the possible absolute
timestamp which may make the event not be able to fit. This causes
the ring buffer to go into an infinite loop trying to find a
sub-buffer that would fit the event. Luckily, there's a check that
will bail out if it looped over a 1000 times and it also warns.
The real fix is not to add the absolute timestamp to an event that is
starting at the beginning of a sub-buffer because it uses the
sub-buffer timestamp.
By avoiding the timestamp at the start of the sub-buffer allows
events that pass the first check to always find a sub-buffer that it
can fit on.
- Have large events that do not fit on a trace_seq to print "LINE TOO
BIG" like it does for the trace_pipe instead of what it does now
which is to silently drop the output.
- Fix a memory leak of forgetting to free the spare page that is saved
by a trace instance.
- Update the size of the snapshot buffer when the main buffer is
updated if the snapshot buffer is allocated.
- Fix ring buffer timestamp logic by removing all the places that tried
to put the before_stamp back to the write stamp so that the next
event doesn't add an absolute timestamp. But each of these updates
added a race where by making the two timestamp equal, it was
validating the write_stamp so that it can be incorrectly used for
calculating the delta of an event.
- There's a temp buffer used for printing the event that was using the
event data size for allocation when it needed to use the size of the
entire event (meta-data and payload data)
- For hardening, use "%.*s" for printing the trace_marker output, to
limit the amount that is printed by the size of the event. This was
discovered by development that added a bug that truncated the '\0'
and caused a crash.
- Fix a use-after-free bug in the use of the histogram files when an
instance is being removed.
- Remove a useless update in the rb_try_to_discard of the write_stamp.
The before_stamp was already changed to force the next event to add
an absolute timestamp that the write_stamp is not used. But the
write_stamp is modified again using an unneeded 64-bit cmpxchg.
- Fix several races in the 32-bit implementation of the
rb_time_cmpxchg() that does a 64-bit cmpxchg.
- While looking at fixing the 64-bit cmpxchg, I noticed that because
the ring buffer uses normal cmpxchg, and this can be done in NMI
context, there's some architectures that do not have a working
cmpxchg in NMI context. For these architectures, fail recording
events that happen in NMI context.
* tag 'trace-v6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Do not record in NMI if the arch does not support cmpxchg in NMI
ring-buffer: Have rb_time_cmpxchg() set the msb counter too
ring-buffer: Fix 32-bit rb_time_read() race with rb_time_cmpxchg()
ring-buffer: Fix a race in rb_time_cmpxchg() for 32 bit archs
ring-buffer: Remove useless update to write_stamp in rb_try_to_discard()
ring-buffer: Do not try to put back write_stamp
tracing: Fix uaf issue when open the hist or hist_debug file
tracing: Add size check when printing trace_marker output
ring-buffer: Have saved event hold the entire event
ring-buffer: Do not update before stamp when switching sub-buffers
tracing: Update snapshot buffer on resize if it is allocated
ring-buffer: Fix memory leak of free page
eventfs: Fix events beyond NAME_MAX blocking tasks
tracing: Have large events show up as '[LINE TOO BIG]' instead of nothing
ring-buffer: Fix writing to the buffer with max_data_size
Linus Torvalds [Sat, 16 Dec 2023 03:59:03 +0000 (19:59 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Arm CMN perf: fix the DTC allocation failure path which can end up
erroneously clearing live counters
- arm64/mm: fix hugetlb handling of the dirty page state leading to a
continuous fault loop in user on hardware without dirty bit
management (DBM). That's caused by the dirty+writeable information
not being properly preserved across a series of mprotect(PROT_NONE),
mprotect(PROT_READ|PROT_WRITE)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Always make sw-dirty PTEs hw-dirty in pte_modify
perf/arm-cmn: Fail DTC counter allocation correctly
Linus Torvalds [Sat, 16 Dec 2023 03:48:47 +0000 (19:48 -0800)]
Merge tag 'pci-v6.7-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Limit Max_Read_Request_Size (MRRS) on some MIPS Loongson systems
because they don't all support MRRS > 256, and firmware doesn't
always initialize it correctly, which meant some PCIe devices didn't
work (Jiaxun Yang)
- Add and use pci_enable_link_state_locked() to prevent potential
deadlocks in vmd and qcom drivers (Johan Hovold)
- Revert recent (v6.5) acpiphp resource assignment changes that fixed
issues with hot-adding devices on a root bus or with large BARs, but
introduced new issues with GPU initialization and hot-adding SCSI
disks in QEMU VMs and (Bjorn Helgaas)
* tag 'pci-v6.7-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
Revert "PCI: acpiphp: Reassign resources on bridge if necessary"
PCI/ASPM: Add pci_disable_link_state_locked() lockdep assert
PCI/ASPM: Clean up __pci_disable_link_state() 'sem' parameter
PCI: qcom: Clean up ASPM comment
PCI: qcom: Fix potential deadlock when enabling ASPM
PCI: vmd: Fix potential deadlock when enabling ASPM
PCI/ASPM: Add pci_enable_link_state_locked()
PCI: loongson: Limit MRRS to 256
Daniel Golle [Tue, 12 Dec 2023 00:05:35 +0000 (00:05 +0000)]
net: phy: skip LED triggers on PHYs on SFP modules
Calling led_trigger_register() when attaching a PHY located on an SFP
module potentially (and practically) leads into a deadlock.
Fix this by not calling led_trigger_register() for PHYs localted on SFP
modules as such modules actually never got any LEDs.
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4-next-20231208+ #0 Tainted: G O
------------------------------------------------------
kworker/u8:2/43 is trying to acquire lock: ffffffc08108c4e8 (triggers_list_lock){++++}-{3:3}, at: led_trigger_register+0x4c/0x1a8
but task is already holding lock: ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Josef Bacik [Fri, 15 Dec 2023 15:01:44 +0000 (10:01 -0500)]
btrfs: do not allow non subvolume root targets for snapshot
Our btrfs subvolume snapshot <source> <destination> utility enforces
that <source> is the root of the subvolume, however this isn't enforced
in the kernel. Update the kernel to also enforce this limitation to
avoid problems with other users of this ioctl that don't have the
appropriate checks in place.
Reported-by: Martin Michaelis <code@mgjm.de> CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Neal Gompa <neal@gompa.dev> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
projects / linux.git / log