drm/rockchip: dw_hdmi: Drop superfluous assignments of mpll_cfg, cur_ctr and phy_config
The mpll_cfg, cur_ctr and phy_config members in struct dw_hdmi_plat_data
are only used to configure the Synopsys PHYs supported internally by DW
HDMI transmitter driver (gpu/drm/bridge/synopsys/dw-hdmi.c), via
hdmi_phy_configure_dwc_hdmi_3d_tx(), which is further invoked from
dw_hdmi_phy_init(). This is part of the internal
dw_hdmi_synopsys_phy_ops struct, managed within dw_hdmi_detect_phy().
To handle vendor PHYs, DW HDMI driver doesn't make use of the internal
PHY ops and, instead, relies on the glue layer to provide the phy_ops
and phy_name members of struct dw_hdmi_plat_data.
Drop the unnecessary assignments of DW internal PHY related members from
structs rk3228_hdmi_drv_data and rk3328_hdmi_drv_data, since both set
the phy_force_vendor flag and correctly provide the expected vendor PHY
data.
drm/rockchip: dw_hdmi: Use devm_regulator_get_enable()
The regulators are only enabled at bind() and disabled at unbind(),
hence replace the boilerplate code by making use of
devm_regulator_get_enable() helper.
Make use of devm_clk_get_optional_enabled() to replace devm_clk_get()
and clk_prepare_enable() for ref_clk and drop the now unnecessary calls
to clk_disable_unprepare().
Additionally, use devm_clk_get_optional() helper for grf_clk to replace
the open coding call to devm_clk_get() followed by the -ENOENT test.
Val Packett [Mon, 24 Jun 2024 20:40:48 +0000 (17:40 -0300)]
drm/rockchip: vop: clear DMA stop bit on RK3066
The RK3066 VOP sets a dma_stop bit when it's done scanning out a frame
and needs the driver to acknowledge that by clearing the bit.
Unless we clear it "between" frames, the RGB output only shows noise
instead of the picture. atomic_flush is the place for it that least
affects other code (doing it on vblank would require converting all
other usages of the reg_lock to spin_(un)lock_irq, which would affect
performance for everyone).
This seems to be a redundant synchronization mechanism that was removed
in later iterations of the VOP hardware block.
drm/rockchip: cdn-dp: Clean up a few logged messages
Clean up a few logged messages, which were previously worded as rather
incomplete sentences separated by periods. This was both a bit unreadable
and grammatically incorrect, so convert them into partial sentences separated
(or connected) by semicolons, together with some wording improvements.
Jani Nikula [Mon, 12 Aug 2024 14:28:48 +0000 (17:28 +0300)]
drm/i915/gvt: stop using drm_edid_block_valid()
We'll want to stop drm_edid_block_valid() usage. KVMGT is the last
user. Replace with drm_edid_valid(), which unfortunately requires an
allocated drm_edid. However, on the plus side, this would be required to
handle the TODO comment about EDID extension block support.
Jani Nikula [Tue, 14 May 2024 12:55:07 +0000 (15:55 +0300)]
drm/rockchip: cdn-dp: get rid of drm_edid_raw()
The dimensions are available in display info, so there's no need for raw
EDID access. While at it, move the debug logging to where the EDID is
actually read.
Jani Nikula [Thu, 6 Jun 2024 12:35:03 +0000 (15:35 +0300)]
drm/edid: reduce DisplayID log spamming
Debug printing at DisplayID validation leads to lots of log spamming as
it's called at DisplayID iterators during EDID parsing. Remove it, and
replace with a less noisy message at connector EDID update.
A vulnerability in the package_index module of pypa/setuptools
versions up to 69.1.1 allows for remote code execution via its
download functions. These functions, which are used to download
packages from URLs provided by users or retrieved from package
index servers, are susceptible to code injection. If these
functions are exposed to user-controlled inputs, such as package
URLs, they can execute arbitrary commands on the system. The
issue is fixed in version 70.0.
Severity: 8.8 / 10 (High)
Attack vector: Network
Attack complexity: Low
Privileges required: None
User interaction: Required
Scope: Unchanged
Confidentiality: High
Integrity: High
Availability: High
CVE ID: CVE-2024-6345"
To avoid disturbing everyone with the kernel repo hosted on GitHub,
I suggest we upgrade our python dependencies once again to appease
GitHub Dependabot.
Tejas Vipin [Tue, 6 Aug 2024 13:59:48 +0000 (19:29 +0530)]
drm/mipi-dsi: add more multi functions for better error handling
Add more functions that can benefit from being multi style and mark
older variants as deprecated to eventually convert all mipi_dsi functions
to multi style.
Acked-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
[dianders: Fixed whitespace warning when applying] Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240806135949.468636-2-tejasvipin76@gmail.com
Dan Carpenter [Mon, 12 Aug 2024 08:29:38 +0000 (11:29 +0300)]
drm/ast: astdp: fix loop timeout check
This code has an issue because it loops until "i" is set to UINT_MAX but
the test for failure assumes that "i" is set to zero. The result is that
it will only print an error message if we succeed on the very last try.
Reformat the loop to count forwards instead of backwards.
Zhang Zekun [Mon, 12 Aug 2024 12:35:43 +0000 (20:35 +0800)]
drm/hisilicon: Remove unused delarations
hibmc_mm_init() has been removed since commit 28645ae064d1
("drm/hisilicon/hibmc: Remove hibmc_ttm.c"), but remain the declaration
untouched in the header files. So, let's remove this unused declaration.
The output_poll_changed hook in struct drm_mode_config_funcs is
unused. Remove it. The helper drm_client_dev_hotplug() implements
the callback's functionality.
drm/nouveau: Implement switcheroo reprobe with drm_client_dev_hotplug()
Replace the call to drm_fb_helper_output_poll_changed() with a call
to drm_client_dev_hotplug(). It is equivalent in functionality, but
uses the DRM client infrastructure.
drm/nouveau: Do not set struct drm_mode_config_funcs.output_poll_changed
The output_poll_changed hook was only necessary before in-kernel
DRM clients existed, but is now obsolete. The client code handles
display hotplugging internally.
drm/nouveau: Do not set struct drm_driver.lastclose
Remove the implementation of struct drm_driver.lastclose. The hook
was only necessary before in-kernel DRM clients existed, but is now
obsolete. The code in nouveau_vga_lastclose() is performed by
drm_lastclose().
drm/amdgpu: Do not set struct drm_driver.lastclose
Remove the implementation of struct drm_driver.lastclose. The hook
was only necessary before in-kernel DRM clients existed, but is now
obsolete. The code in amdgpu_driver_lastclose_kms() is performed by
drm_lastclose().
Amdgpu and nouveau call vga_switcheroo_process_delayed_switch() from
their lastclose callbacks. Call it from drm_lastclose(), so that the
driver functions can finally be removed. Only PCI devices with enabled
switcheroo do the delayed switching. The call has no effect on other
hardware.
v2:
- move change to drm_lastclose() (Sima)
- update docs for vga_switcheroo_process_delayed_switch()
Daniel Yang [Fri, 9 Aug 2024 03:23:50 +0000 (20:23 -0700)]
drm/connector: kerneldoc: Fix two missing newlines in drm_connector.c
Fix the unexpected indentation errors.
drm_connector.c has some kerneldoc comments that were missing newlines.
This results in the following warnings when running make htmldocs:
./Documentation/gpu/drm-kms:538: ./drivers/gpu/drm/drm_connector.c:2344: WARNING: Definition list ends without a blank line; unexpected unindent. [docutils]
./Documentation/gpu/drm-kms:538: ./drivers/gpu/drm/drm_connector.c:2346: ERROR: Unexpected indentation. [docutils]
./Documentation/gpu/drm-kms:538: ./drivers/gpu/drm/drm_connector.c:2368: WARNING: Block quote ends without a blank line; unexpected unindent. [docutils]
./Documentation/gpu/drm-kms:538: ./drivers/gpu/drm/drm_connector.c:2381: ERROR: Unexpected indentation. [docutils]
Mohammed Anees [Sun, 11 Aug 2024 10:16:51 +0000 (06:16 -0400)]
drm: Add missing documentation for struct drm_plane_size_hint
This patch takes care of the following warnings during documentation
compiling:
./include/uapi/drm/drm_mode.h:869: warning: Function parameter or struct member 'width' not described in 'drm_plane_size_hint'
./include/uapi/drm/drm_mode.h:869: warning: Function parameter or struct member 'height' not described in 'drm_plane_size_hint'
Jocelyn Falempe [Wed, 7 Aug 2024 13:36:14 +0000 (15:36 +0200)]
drm/panic: Add panic description
Now that kmsg dump callback has the description parameter, use it in
the user panic screen.
This is the string passed to panic(), like "VFS: Unable to mount root
fs on xxx" or "Attempted to kill init! exitcode=0xxxx".
It gives a hint on why the panic occurred, without being too cryptic.
Jocelyn Falempe [Wed, 7 Aug 2024 13:36:12 +0000 (15:36 +0200)]
drm/panic: Move drm_panic_register prototype to drm_crtc_internal.h
drm_panic_[un]register() are only used by the core drm, and are not
intended to be called by other drm drivers, so move their prototypes
to drm_crtc_internal.h.
Mgag200's BMC connector tracks the status of an underlying physical
connector and updates the BMC status accordingly. This functionality
works around GNOME's settings app, which cannot handle multiple
outputs on the same CRTC.
The workaround is now obsolete as the VGA-BMC connector handles BMC
support internally. Hence, remove the driver's code and the BMC output
entirely.
drm/mgag200: vga-bmc: Control BMC scanout from encoder
Move calls to stop and start BMC scanout from CRTC helpers to the
VGA-BMC encoder's atomic_disable and atomic_enable. Makes the BMC
scanout transparent to the CRTC.
DRM's atomic helpers call an encoder's atomic_disable and atomic_enable
helpers for all enabled encoders. The BMC stops scanning out the VGA
signal if modeset disables the VGA encoder, and starts scanning out
if the modeset enables the VGA encoder.
drm/mgag200: vga-bmc: Control CRTC VIDRST flag from encoder
Control the VIDRST pin from the VGA-BMC encoder's atomic_check and
remove the respective code from CRTC. Makes the VIDRST functionality
fully composable.
The VIDRST pin allows an external clock source to control the SYNC
signals of the Matrox chip. The functionality is part of the CRTC,
but depends on the presence of the clock source. This is the case for
some BMCs, so control the pin from the VGA-BMC output.
The VGA-BMC connector selects the VGA output if a display has been
attached to the physical connector. Otherwise it selects the BMC
output. In any case, the connector status is set to 'detected', so
that the userspace compositor displays to it.
Depending on the setting, the connector's display modes either come
from the VGA monitor's EDID or from an internal list of BMC-compatible
modes.
Duplicate VGA output to VGA-BMC output and update all code for Matrox
server chips. The new output represents a VGA output that has a BMC
attached to it. No functional changes so far.
drm/ci: rockchip: add tests for rockchip display driver
For rockchip rk3288 and rk3399, the display driver is rockchip
and gpu driver is panfrost. Currently, in drm-ci for rockchip
rk3288 and rk3399, only the gpu driver is tested. Refactor
the existing rockchip jobs to test both display and gpu driver
and update xfails.
Since the correct driver name is passed from the job to test gpu
and display driver, remove the check to set IGT_FORCE_DRIVER
based on driver name for rockchip jobs.
For Amlogic Meson G12B (A311D) SOC the display driver is meson and
gpu driver is panfrost. Currently, in drm-ci for Meson G12B (A311D),
only the gpu driver is tested. Refactor the existing meson jobs
and add support in drm-ci to test both display and gpu driver for
Amlogic Meson G12B (A311D) and update xfails.
Since the correct driver name is passed from the job to test gpu
and display driver, remove the check to set IGT_FORCE_DRIVER
based on driver name for meson jobs.
drm/ci: mediatek: add tests for powervr gpu driver
For mediatek mt8173, the display driver is mediatek, while the
gpu driver is powervr. Currently, in drm-ci for mt8173, only the
display driver is tested. Add support in drm-ci to test powervr
driver for mt8173. Powervr driver was merged in linux kernel,
but there's no mediatek support yet. So disable the powervr:mt8173
job which uses powervr driver.
Also update the MAINTAINERS file to include xfails for powervr driver.
drm/ci: mediatek: add tests for mediatek display driver
For mediatek mt8183, the display driver is mediatek, while the
gpu driver is panfrost. Currently, in drm-ci for mt8183, only
the gpu driver is tested. Refactor the existing mediatek jobs
and add support in drm-ci to test both display and gpu driver
for mt8183 and update xfails.
Since the correct driver name is passed from the job to test gpu
and display driver, remove the check to set IGT_FORCE_DRIVER
based on driver name for mediatek jobs.
Update the MAINTAINERS file to include xfails for panfrost driver.
Enable CONFIG_DRM_ANALOGIX_ANX7625 in the arm64 defconfig to get
display driver probed on the mt8183-kukui-jacuzzi-juniper machine.
arch/arm64/configs/defconfig has CONFIG_DRM_ANALOGIX_ANX7625=m,
but drm-ci don't have initrd with modules, so add
CONFIG_DRM_ANALOGIX_ANX7625=y in CI arm64 config.
drm/bridge: lt9611uxc: drop support for !DRM_BRIDGE_ATTACH_NO_CONNECTOR
Having no in-kernel devices that use !DRM_BRIDGE_ATTACH_NO_CONNECTOR
mode for the Lontium LT9611UXC bridge, drop the in-bridge implementation
of the drm_connector.
Dave Airlie [Mon, 5 Aug 2024 08:47:30 +0000 (18:47 +1000)]
Merge tag 'drm-xe-next-2024-07-30' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
drm-xe-next for 6.12
UAPI Changes:
- Rename xe perf layer as xe observation layer, but was
also made available via fixes to previous verison (Ashutosh)
- Use write-back caching mode for system memory on DGFX,
but was also mad available via fixes to previous version (Thomas)
- Expose SIMD16 EU mask in topology query for userspace to know
the type of EU, as available in PVC, Lunar Lake and Battlemage
(Lucas)
- Return ENOBUFS instead of ENOMEM in vm_bind if failure is tied
to an array of binds (Matthew Brost)
Driver Changes:
- Log cleanup moving messages to debug priority (Michal Wajdeczko)
- Add timeout to fences to adhere to dma_buf rules (Matthew Brost)
- Rename old engine nomenclature to exec_queue (Matthew Brost)
- Convert multiple bind ops to 1 job (Matthew Brost)
- Add error injection for vm bind to help testing error path
(Matthew Brost)
- Fix error handling in page table to propagate correctly
to userspace (Matthew Brost)
- Re-organize and cleanup SR-IOV related registers (Michal Wajdeczko)
- Make the device write barrier compatible with VF (Michal Wajdeczko)
- New display workarounds for Battlemage (Matthew Auld)
- New media workarounds for Lunar Lake and Battlemage (Ngai-Mint Kwan)
- New graphics workarounds for Lunar Lake (Bommu Krishnaiah)
- Tracepoint updates (Matthew Brost, Nirmoy Das)
- Cleanup the header generation for OOB workarounds (Lucas De Marchi)
- Fix leaking HDCP-related object (Nirmoy Das)
- Serialize L2 flushes to avoid races (Tejas Upadhyay)
- Log pid and comm on job timeout (José Roberto de Souza)
- Simplify boilerplate code for live kunit (Michal Wajdeczko)
- Improve kunit skips for live kunit (Michal Wajdeczko)
- Fix xe_sync cleanup when handling xe_exec ioctl (Ashutosh Dixit)
- Limit fair VF LMEM provisioning (Michal Wajdeczko)
- New workaround to fence mmio writes in Lunar Lake (Tejas Upadhyay)
- Warn on writes inaccessible register in VF (Michal Wajdeczko)
- Fix register lookup in VF (Michal Wajdeczko)
- Add GSC support for Battlemage (Alexander Usyskin)
- Fix wedging only the GT in which timeout occurred (Matthew Brost)
- Block device suspend when wedging (Matthew Brost)
- Handle compression and migration changes for Battlemage
(Akshata Jahagirdar)
- Limit access of stolen memory for Lunar Lake (Uma Shankar)
- Fail invalid addresses during user fence creation (Matthew Brost)
- Refcount xe_file to safely and accurately store fdinfo stats
(Umesh Nerlige Ramappa)
- Cleanup and fix PM reference for TLB invalidation code
(Matthew Brost)
- Fix PM reference handling when communicating with GuC (Matthew Brost)
- Add new BO flag for 2 MiB alignement and use in VF (Michal Wajdeczko)
- Simplify MMIO setup for multi-tile platforms (Lucas De Marchi)
- Add check for uninitialized access to OOB workarounds
(Lucas De Marchi)
- New GSC and HuC firmware blobs for Lunar Lake and Battlemage
(Daniele Ceraolo Spurio)
- Unify mmio wait logic (Gustavo Sousa)
- Fix off-by-one when processing RTP rules (Lucas De Marchi)
- Future-proof migrate logic with compressed PAT flag (Matt Roper)
- Add WA kunit tests for Battlemage (Lucas De Marchi)
- Test active tracking for workaorunds with kunit (Lucas De Marchi)
- Add kunit tests for RTP with no actions (Lucas De Marchi)
- Unify parse of OR rules in RTP (Lucas De Marchi)
- Add performance tuning for Battlemage (Sai Teja Pottumuttu)
- Make bit masks unsigned (Geert Uytterhoeven)
Tetsuo Handa [Sun, 4 Aug 2024 09:48:10 +0000 (18:48 +0900)]
profiling: remove profile=sleep support
The kernel sleep profile is no longer working due to a recursive locking
bug introduced by commit 42a20f86dc19 ("sched: Add wrapper for get_wchan()
to keep task blocked")
Booting with the 'profile=sleep' kernel command line option added or
executing
# echo -n sleep > /sys/kernel/profiling
after boot causes the system to lock up.
Lockdep reports
kthreadd/3 is trying to acquire lock: ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: get_wchan+0x32/0x70
but task is already holding lock: ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: try_to_wake_up+0x53/0x370
However, since nobody noticed this regression for more than two years,
let's remove 'profile=sleep' support based on the assumption that nobody
needs this functionality.
Linus Torvalds [Sun, 4 Aug 2024 15:57:08 +0000 (08:57 -0700)]
Merge tag 'x86-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Prevent a deadlock on cpu_hotplug_lock in the aperf/mperf driver.
A recent change in the ACPI code which consolidated code pathes moved
the invocation of init_freq_invariance_cppc() to be moved to a CPU
hotplug handler. The first invocation on AMD CPUs ends up enabling a
static branch which dead locks because the static branch enable tries
to acquire cpu_hotplug_lock but that lock is already held write by
the hotplug machinery.
Use static_branch_enable_cpuslocked() instead and take the hotplug
lock read for the Intel code path which is invoked from the
architecture code outside of the CPU hotplug operations.
- Fix the number of reserved bits in the sev_config structure bit field
so that the bitfield does not exceed 64 bit.
- Add missing Zen5 model numbers
- Fix the alignment assumptions of pti_clone_pgtable() and
clone_entry_text() on 32-bit:
The code assumes PMD aligned code sections, but on 32-bit the kernel
entry text is not PMD aligned. So depending on the code size and
location, which is configuration and compiler dependent, entry text
can cross a PMD boundary. As the start is not PMD aligned adding PMD
size to the start address is larger than the end address which
results in partially mapped entry code for user space. That causes
endless recursion on the first entry from userspace (usually #PF).
Cure this by aligning the start address in the addition so it ends up
at the next PMD start address.
clone_entry_text() enforces PMD mapping, but on 32-bit the tail might
eventually be PTE mapped, which causes a map fail because the PMD for
the tail is not a large page mapping. Use PTI_LEVEL_KERNEL_IMAGE for
the clone() invocation which resolves to PTE on 32-bit and PMD on
64-bit.
- Zero the 8-byte case for get_user() on range check failure on 32-bit
The recend consolidation of the 8-byte get_user() case broke the
zeroing in the failure case again. Establish it by clearing ECX
before the range check and not afterwards as that obvioulsy can't be
reached when the range check fails
* tag 'x86-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uaccess: Zero the 8-byte get_range case on failure on 32-bit
x86/mm: Fix pti_clone_entry_text() for i386
x86/mm: Fix pti_clone_pgtable() alignment assumption
x86/setup: Parse the builtin command line before merging
x86/CPU/AMD: Add models 0x60-0x6f to the Zen5 range
x86/sev: Fix __reserved field in sev_config
x86/aperfmperf: Fix deadlock on cpu_hotplug_lock
Linus Torvalds [Sun, 4 Aug 2024 15:50:16 +0000 (08:50 -0700)]
Merge tag 'timers-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two fixes for the timer/clocksource code:
- The recent fix to make the take over of the broadcast timer more
reliable retrieves a per CPU pointer in preemptible context.
This went unnoticed in testing as some compilers hoist the access
into the non-preemotible section where the pointer is actually
used, but obviously compilers can rightfully invoke it where the
code put it.
Move it into the non-preemptible section right to the actual usage
side to cure it.
- The clocksource watchdog is supposed to emit a warning when the
retry count is greater than one and the number of retries reaches
the limit.
The condition is backwards and warns always when the count is
greater than one. Fixup the condition to prevent spamming dmesg"
* tag 'timers-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()
tick/broadcast: Move per CPU pointer access into the atomic section
Linus Torvalds [Sun, 4 Aug 2024 15:46:14 +0000 (08:46 -0700)]
Merge tag 'sched-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
- When stime is larger than rtime due to accounting imprecision, then
utime = rtime - stime becomes negative. As this is unsigned math, the
result becomes a huge positive number.
Cure it by resetting stime to rtime in that case, so utime becomes 0.
- Restore consistent state when sched_cpu_deactivate() fails.
When offlining a CPU fails in sched_cpu_deactivate() after the SMT
present counter has been decremented, then the function aborts but
fails to increment the SMT present counter and leaves it imbalanced.
Consecutive operations cause it to underflow. Add the missing fixup
for the error path.
For SMT accounting the runqueue needs to marked online again in the
error exit path to restore consistent state.
* tag 'sched-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix unbalance set_rq_online/offline() in sched_cpu_deactivate()
sched/core: Introduce sched_set_rq_on/offline() helper
sched/smt: Fix unbalance sched_smt_present dec/inc
sched/smt: Introduce sched_smt_present_inc/dec() helper
sched/cputime: Fix mul_u64_u64_div_u64() precision for cputime
Linus Torvalds [Sun, 4 Aug 2024 15:42:18 +0000 (08:42 -0700)]
Merge tag 'perf-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf fixes from Thomas Gleixner:
- Move the smp_processor_id() invocation back into the non-preemtible
region, so that the result is valid to use
- Add the missing package C2 residency counters for Sierra Forest CPUs
to make the newly added support actually useful
* tag 'perf-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix smp_processor_id()-in-preemptible warnings
perf/x86/intel/cstate: Add pkg C2 residency counter for Sierra Forest
Linus Torvalds [Sun, 4 Aug 2024 15:36:57 +0000 (08:36 -0700)]
Merge tag 'irq-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A couple of fixes for interrupt chip drivers:
- Make sure to skip the clear register space in the MBIGEN driver
when calculating the node register index. Otherwise the clear
register is clobbered and the wrong node registers are accessed.
- Fix a signed/unsigned confusion in the loongarch CPU driver which
converts an error code to a huge "valid" interrupt number.
- Convert the mesion GPIO interrupt controller lock to a raw spinlock
so it works on RT.
- Add a missing static to a internal function in the pic32 EVIC
driver"
* tag 'irq-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mbigen: Fix mbigen node address layout
irqchip/meson-gpio: Convert meson_gpio_irq_controller::lock to 'raw_spinlock_t'
irqchip/irq-pic32-evic: Add missing 'static' to internal function
irqchip/loongarch-cpu: Fix return value of lpic_gsi_to_irq()
Linus Torvalds [Sun, 4 Aug 2024 15:32:31 +0000 (08:32 -0700)]
Merge tag 'locking-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two fixes for locking and jump labels:
- Ensure that the atomic_cmpxchg() conditions are correct and
evaluating to true on any non-zero value except 1. The missing
check of the return value leads to inconsisted state of the jump
label counter.
- Add a missing type conversion in the paravirt spinlock code which
makes loongson build again"
* tag 'locking-urgent-2024-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
jump_label: Fix the fix, brown paper bags galore
locking/pvqspinlock: Correct the type of "old" variable in pv_kick_node()
arm: dts: arm: versatile-ab: Fix duplicate clock node name
Commit 04f08ef291d4 ("arm/arm64: dts: arm: Use generic clock and
regulator nodenames") renamed nodes and created 2 "clock-24000000" nodes
(at different paths).
The kernel can't handle these duplicate names even though they are at
different paths. Fix this by renaming one of the nodes to "clock-pclk".
This name is aligned with other Arm boards (those didn't have a known
frequency to use in the node name).
Linus Torvalds [Sun, 4 Aug 2024 15:18:40 +0000 (08:18 -0700)]
Merge tag '6.11-rc1-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two reparse point fixes
- minor cleanup
- additional trace point (to help debug a recent problem)
* tag '6.11-rc1-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
smb: client: fix FSCTL_GET_REPARSE_POINT against NetApp
smb3: add dynamic tracepoints for shutdown ioctl
cifs: Remove cifs_aio_ctx
smb: client: handle lack of FSCTL_GET_REPARSE_POINT support
Linus Torvalds [Sun, 4 Aug 2024 15:12:33 +0000 (08:12 -0700)]
Merge tag 'media/v6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- two Kconfig fixes
- one fix for the UVC driver addressing probing time detection of a UVC
custom controls
- one fix related to PDF generation
* tag 'media/v6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: v4l: Fix missing tabular column hint for Y14P format
media: intel/ipu6: select AUXILIARY_BUS in Kconfig
media: ipu-bridge: fix ipu6 Kconfig dependencies
media: uvcvideo: Fix custom control mapping probing
Linus Torvalds [Sat, 3 Aug 2024 22:12:56 +0000 (15:12 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core change that reverts the double message print patch in sd.c
(it was causing regressions on embedded systems).
The rest are driver fixes in ufs, mpt3sas and mpi3mr"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: exynos: Don't resume FMP when crypto support is disabled
scsi: mpt3sas: Avoid IOMMU page faults on REPORT ZONES
scsi: mpi3mr: Avoid IOMMU page faults on REPORT ZONES
scsi: ufs: core: Do not set link to OFF state while waking up from hibernation
scsi: Revert "scsi: sd: Do not repeat the starting disk message"
scsi: ufs: core: Fix deadlock during RTC update
scsi: ufs: core: Bypass quick recovery if force reset is needed
scsi: ufs: core: Check LSDBS cap when !mcq
Linus Torvalds [Sat, 3 Aug 2024 16:09:25 +0000 (09:09 -0700)]
Merge tag 'xfs-6.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Chandan Babu:
- Fix memory leak when corruption is detected during scrubbing parent
pointers
- Allow SECURE namespace xattrs to use reserved block pool to in order
to prevent ENOSPC
- Save stack space by passing tracepoint's char array to file_path()
instead of another stack variable
- Remove unused parameter in macro XFS_DQUOT_LOGRES
- Replace comma with semicolon in a couple of places
* tag 'xfs-6.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: convert comma to semicolon
xfs: convert comma to semicolon
xfs: remove unused parameter in macro XFS_DQUOT_LOGRES
xfs: fix file_path handling in tracepoints
xfs: allow SECURE namespace xattrs to use reserved block pool
xfs: fix a memory leak
Linus Torvalds [Sat, 3 Aug 2024 16:03:21 +0000 (09:03 -0700)]
Merge tag 'parisc-for-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix unaligned memory accesses when calling BPF functions
- adjust memory size constants to fix possible DMA corruptions
* tag 'parisc-for-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix a possible DMA corruption
parisc: fix unaligned accesses in BPF
Linus Torvalds [Sat, 3 Aug 2024 01:12:06 +0000 (18:12 -0700)]
runtime constants: deal with old decrepit linkers
The runtime constants linker script depended on documented linker
behavior [1]:
"If an output section’s name is the same as the input section’s name
and is representable as a C identifier, then the linker will
automatically PROVIDE two symbols: __start_SECNAME and __stop_SECNAME,
where SECNAME is the name of the section. These indicate the start
address and end address of the output section respectively"
to just automatically define the symbol names for the bounds of the
runtime constant arrays.
It turns out that this isn't actually something we can rely on, with old
linkers not generating these automatic symbols. It looks to have been
introduced in binutils-2.29 back in 2017, and we still support building
with versions all the way back to binutils-2.25 (from 2015).
And yes, Oleg actually seems to be using such ancient versions of
binutils.
So instead of depending on the implicit symbols from "section names
match and are representable C identifiers", just do this all manually.
It's not like it causes us any extra pain, we already have to do that
for all the other sections that we use that often have special
characters in them.
Linus Torvalds [Fri, 2 Aug 2024 21:18:31 +0000 (14:18 -0700)]
Merge tag 'io_uring-6.11-20240802' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"Two minor tweaks for the NAPI handling, both from Olivier:
- Kill two unused list definitions
- Ensure that multishot NAPI doesn't age away"
* tag 'io_uring-6.11-20240802' of git://git.kernel.dk/linux:
io_uring: remove unused local list heads in NAPI functions
io_uring: keep multishot request NAPI timeout current
Linus Torvalds [Fri, 2 Aug 2024 21:10:11 +0000 (14:10 -0700)]
Merge tag 'thermal-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix a few issues related to the MSI IRQs management in the
int340x thermal driver, fix a thermal core issue that may lead to
missing trip point crossing events and update the thermal core
documentation.
Specifics:
- Fix MSI error path cleanup in int340x, allow it to work with a
subset of thermal MSI IRQs if some of them are not working and make
it free all MSI IRQs on module exit (Srinivas Pandruvada)
- Fix a thermal core issue that may lead to missing trip point
crossing events in some cases when thermal_zone_set_trips() is used
and update the thermal core documentation (Rafael Wysocki)"
* tag 'thermal-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Update thermal zone registration documentation
thermal: trip: Avoid skipping trips in thermal_zone_set_trips()
thermal: intel: int340x: Free MSI IRQ vectors on module exit
thermal: intel: int340x: Allow limited thermal MSI support
thermal: intel: int340x: Fix kernel warning during MSI cleanup
Linus Torvalds [Fri, 2 Aug 2024 17:33:06 +0000 (10:33 -0700)]
Merge tag 'ceph-for-6.11-rc2' of https://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for a potential hang in the MDS when cap revocation races with
the client releasing the caps in question, marked for stable"
* tag 'ceph-for-6.11-rc2' of https://github.com/ceph/ceph-client:
ceph: force sending a cap update msg back to MDS for revoke op
Linus Torvalds [Fri, 2 Aug 2024 17:17:49 +0000 (10:17 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"The bulk of the changes here is a largish change to guest_memfd,
delaying the clearing and encryption of guest-private pages until they
are actually added to guest page tables. This started as "let's make
it impossible to misuse the API" for SEV-SNP; but then it ballooned a
bit.
The new logic is generally simpler and more ready for hugepage support
in guest_memfd.
Summary:
- fix latent bug in how usage of large pages is determined for
confidential VMs
- fix "underline too short" in docs
- eliminate log spam from limited APIC timer periods
- disallow pre-faulting of memory before SEV-SNP VMs are initialized
- delay clearing and encrypting private memory until it is added to
guest page tables
- this change also enables another small cleanup: the checks in
SNP_LAUNCH_UPDATE that limit it to non-populated, private pages can
now be moved in the common kvm_gmem_populate() function
- fix compilation error that the RISC-V merge introduced in selftests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86/mmu: fix determination of max NPT mapping level for private pages
KVM: riscv: selftests: Fix compile error
KVM: guest_memfd: abstract how prepared folios are recorded
KVM: guest_memfd: let kvm_gmem_populate() operate only on private gfns
KVM: extend kvm_range_has_memory_attributes() to check subset of attributes
KVM: cleanup and add shortcuts to kvm_range_has_memory_attributes()
KVM: guest_memfd: move check for already-populated page to common code
KVM: remove kvm_arch_gmem_prepare_needed()
KVM: guest_memfd: make kvm_gmem_prepare_folio() operate on a single struct kvm
KVM: guest_memfd: delay kvm_gmem_prepare_folio() until the memory is passed to the guest
KVM: guest_memfd: return locked folio from __kvm_gmem_get_pfn
KVM: rename CONFIG_HAVE_KVM_GMEM_* to CONFIG_HAVE_KVM_ARCH_GMEM_*
KVM: guest_memfd: do not go through struct page
KVM: guest_memfd: delay folio_mark_uptodate() until after successful preparation
KVM: guest_memfd: return folio from __kvm_gmem_get_pfn()
KVM: x86: disallow pre-fault for SNP VMs before initialization
KVM: Documentation: Fix title underline too short warning
KVM: x86: Eliminate log spam from limited APIC timer periods
Paolo Bonzini [Fri, 2 Aug 2024 16:31:48 +0000 (12:31 -0400)]
Merge branch 'kvm-fixes' into HEAD
* fix latent bug in how usage of large pages is determined for
confidential VMs
* fix "underline too short" in docs
* eliminate log spam from limited APIC timer periods
* disallow pre-faulting of memory before SEV-SNP VMs are initialized
* delay clearing and encrypting private memory until it is added to
guest page tables
* this change also enables another small cleanup: the checks in
SNP_LAUNCH_UPDATE that limit it to non-populated, private pages
can now be moved in the common kvm_gmem_populate() function
Linus Torvalds [Fri, 2 Aug 2024 16:33:35 +0000 (09:33 -0700)]
Merge tag 'riscv-for-linus-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid dropping some of the internal pseudo-extensions, which
breaks *envcfg dependency parsing
- The kernel entry address is now aligned in purgatory, which avoids a
misaligned load that can lead to crash on systems that don't support
misaligned accesses early in boot
- The FW_SFENCE_VMA_RECEIVED perf event was duplicated in a handful of
perf JSON configurations, one of them been updated to
FW_SFENCE_VMA_ASID_SENT
- The starfive cache driver is now restricted to 64-bit systems, as it
isn't 32-bit clean
- A fix for to avoid aliasing legacy-mode perf counters with software
perf counters
- VM_FAULT_SIGSEGV is now handled in the page fault code
- A fix for stalls during CPU hotplug due to IPIs being disabled
- A fix for memblock bounds checking. This manifests as a crash on
systems with discontinuous memory maps that have regions that don't
fit in the linear map
* tag 'riscv-for-linus-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix linear mapping checks for non-contiguous memory regions
RISC-V: Enable the IPI before workqueue_online_cpu()
riscv/mm: Add handling for VM_FAULT_SIGSEGV in mm_fault_error()
perf: riscv: Fix selecting counters in legacy mode
cache: StarFive: Require a 64-bit system
perf arch events: Fix duplicate RISC-V SBI firmware event name
riscv/purgatory: align riscv_kernel_entry
riscv: cpufeature: Do not drop Linux-internal extensions
clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()
The current "nretries > 1 || nretries >= max_retries" check in
cs_watchdog_read() will always evaluate to true, and thus pr_warn(), if
nretries is greater than 1. The intent is instead to never warn on the
first try, but otherwise warn if the successful retry was the last retry.
Therefore, change that "||" to "&&".
Fixes: db3a34e17433 ("clocksource: Retry clock read if long delays detected") Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20240802154618.4149953-2-paulmck@kernel.org
Linus Torvalds [Fri, 2 Aug 2024 16:14:48 +0000 (09:14 -0700)]
Merge tag 'asm-generic-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"These are three important bug fixes for the cross-architecture tree,
fixing a regression with the new syscall.tbl file, the inconsistent
numbering for the new uretprobe syscall and a bug with iowrite64be on
alpha"
* tag 'asm-generic-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
syscalls: fix syscall macros for newfstat/newfstatat
uretprobe: change syscall number, again
alpha: fix ioread64be()/iowrite64be() helpers
Linus Torvalds [Fri, 2 Aug 2024 16:04:57 +0000 (09:04 -0700)]
Merge tag 'sound-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A small collection of fixes:
- Revert of FireWire changes that caused a long-time regression
- Another long-time regression fix for AMD HDMI
- MIDI2 UMP fixes
- HD-audio Conexant codec fixes and a quirk"
* tag 'sound-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: Conditionally use snooping for AMD HDMI
ALSA: usb-audio: Correct surround channels in UAC1 channel map
ALSA: seq: ump: Explicitly reset RPN with Null RPN
ALSA: seq: ump: Transmit RPN/NRPN message at each MSB/LSB data reception
ALSA: seq: ump: Use the common RPN/bank conversion context
ALSA: ump: Explicitly reset RPN with Null RPN
ALSA: ump: Transmit RPN/NRPN message at each MSB/LSB data reception
Revert "ALSA: firewire-lib: operate for period elapse event in process context"
Revert "ALSA: firewire-lib: obsolete workqueue for period update"
ALSA: hda/realtek: Add quirk for Acer Aspire E5-574G
ALSA: seq: ump: Optimize conversions from SysEx to UMP
ALSA: hda/conexant: Mute speakers at suspend / shutdown
ALSA: hda/generic: Add a helper to mute speakers at suspend/shutdown
ALSA: hda: conexant: Fix headset auto detect fail in the polling mode
Linus Torvalds [Fri, 2 Aug 2024 15:59:09 +0000 (08:59 -0700)]
Merge tag 'drm-fixes-2024-08-02' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Regular weekly fixes. This is a bit larger than usual but doesn't seem
too crazy.
Most of it is vmwgfx changes that fix a bunch of issues with wayland
userspaces with dma-buf/external buffers and modesetting fixes.
Otherwise it's kinda spread out, v3d fixes some new ioctls, nouveau
has regression revert and fixes, amdgpu, i915 and ast have some small
fixes, and some core fixes spread about.
client:
- fix error code
atomic:
- allow damage clips with async flips
- allow explicit sync with async flips
kselftests:
- fix dmabuf-heaps test
panic:
- fix schedule_work in panic paths
panel:
- fix OrangePi Neo orientation
gpuvm:
- fix missing dependency
amdgpu:
- SMU 14.x update
- Fix contiguous VRAM handling for IB parsing
- GFX 12 fix
- Regression fix for old APUs
i915:
- Static analysis fix for int overflow
- Fix for HDCP2_STREAM_STATUS macro and removal of PWR_CLK_STATE for gen12
nouveau:
- revert busy wait change that caused a resume regression
- fix buffer placement fault on dynamic pm s/r
- fix refcount underflow
ast:
- fix black screen on resume
- wake during connector status detect
v3d:
- fix issues with perf/timestamp ioctls
vmwgfx:
- fix deadlock in dma-buf fence polling
- fix screen surface refcounting
- fix dumb buffer handling
- fix support for external buffers
- fix overlay with screen targets
- trigger modeset on screen moves"
* tag 'drm-fixes-2024-08-02' of https://gitlab.freedesktop.org/drm/kernel: (31 commits)
Revert "nouveau: rip out busy fence waits"
nouveau: set placement to original placement on uvmm validate.
drm/atomic: Allow userspace to use damage clips with async flips
drm/atomic: Allow userspace to use explicit sync with atomic async flips
drm/i915: Fix possible int overflow in skl_ddi_calculate_wrpll()
drm/i915/hdcp: Fix HDCP2_STREAM_STATUS macro
drm/ast: astdp: Wake up during connector status detection
i915/perf: Remove code to update PWR_CLK_STATE for gen12
kselftests: dmabuf-heaps: Ensure the driver name is null-terminated
drm/client: Fix error code in drm_client_buffer_vmap_local()
drm/amdgpu: Fix APU handling in amdgpu_pm_load_smu_firmware()
drm/amdgpu: increase mes log buffer size for gfx12
drm/amdgpu: fix contiguous handling for IB parsing v2
drm/amdgpu/pm: support gpu_metrics sysfs interface for smu v14.0.2/3
drm/vmwgfx: Trigger a modeset when the screen moves
drm/vmwgfx: Fix overlay when using Screen Targets
drm/vmwgfx: Add basic support for external buffers
drm/vmwgfx: Fix handling of dumb buffers
drm/vmwgfx: Make sure the screen surface is ref counted
drm/vmwgfx: Fix a deadlock in dma buf fence polling
...
Paulo Alcantara [Thu, 1 Aug 2024 21:12:39 +0000 (18:12 -0300)]
smb: client: fix FSCTL_GET_REPARSE_POINT against NetApp
NetApp server requires the file to be open with FILE_READ_EA access in
order to support FSCTL_GET_REPARSE_POINT, otherwise it will return
STATUS_INVALID_DEVICE_REQUEST. It doesn't make any sense because
there's no requirement for FILE_READ_EA bit to be set nor
STATUS_INVALID_DEVICE_REQUEST being used for something other than
"unsupported reparse points" in MS-FSA.
To fix it and improve compatibility, set FILE_READ_EA & SYNCHRONIZE
bits to match what Windows client currently does.
Tested-by: Sebastian Steinbeisser <Sebastian.Steinbeisser@lrz.de> Acked-by: Tom Talpey <tom@talpey.com> Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Tue, 30 Jul 2024 05:26:21 +0000 (00:26 -0500)]
smb3: add dynamic tracepoints for shutdown ioctl
For debugging an umount failure in xfstests generic/043 generic/044 in some
configurations, we needed more information on the shutdown ioctl which
was suspected of being related to the cause, so tracepoints are added
in this patch e.g.
"trace-cmd record -e smb3_shutdown_enter -e smb3_shutdown_done -e smb3_shutdown_err"
David Howells [Wed, 31 Jul 2024 10:30:00 +0000 (11:30 +0100)]
cifs: Remove cifs_aio_ctx
Remove struct cifs_aio_ctx and its associated alloc/release functions as it
is no longer used, the functions being taken over by netfslib.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara [Wed, 31 Jul 2024 13:23:39 +0000 (10:23 -0300)]
smb: client: handle lack of FSCTL_GET_REPARSE_POINT support
As per MS-FSA 2.1.5.10.14, support for FSCTL_GET_REPARSE_POINT is
optional and if the server doesn't support it,
STATUS_INVALID_DEVICE_REQUEST must be returned for the operation.
If we find files with reparse points and we can't read them due to
lack of client or server support, just ignore it and then treat them
as regular files or junctions.
Fixes: 5f71ebc41294 ("smb: client: parse reparse point flag in create response") Reported-by: Sebastian Steinbeisser <Sebastian.Steinbeisser@lrz.de> Tested-by: Sebastian Steinbeisser <Sebastian.Steinbeisser@lrz.de> Acked-by: Tom Talpey <tom@talpey.com> Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Will Deacon [Wed, 31 Jul 2024 13:36:01 +0000 (14:36 +0100)]
arm64: jump_label: Ensure patched jump_labels are visible to all CPUs
Although the Arm architecture permits concurrent modification and
execution of NOP and branch instructions, it still requires some
synchronisation to ensure that other CPUs consistently execute the newly
written instruction:
> When the modified instructions are observable, each PE that is
> executing the modified instructions must execute an ISB or perform a
> context synchronizing event to ensure execution of the modified
> instructions
Prior to commit f6cc0c501649 ("arm64: Avoid calling stop_machine() when
patching jump labels"), the arm64 jump_label patching machinery
performed synchronisation using stop_machine() after each modification,
however this was problematic when flipping static keys from atomic
contexts (namely, the arm_arch_timer CPU hotplug startup notifier) and
so we switched to the _nosync() patching routines to avoid "scheduling
while atomic" BUG()s during boot.
In hindsight, the analysis of the issue in f6cc0c501649 isn't quite
right: it cites the use of IPIs in the default patching routines as the
cause of the lockup, whereas stop_machine() does not rely on IPIs and
the I-cache invalidation is performed using __flush_icache_range(),
which elides the call to kick_all_cpus_sync(). In fact, the blocking
wait for other CPUs is what triggers the BUG() and the problem remains
even after f6cc0c501649, for example because we could block on the
jump_label_mutex. Eventually, the arm_arch_timer driver was fixed to
avoid the static key entirely in commit a862fc2254bd
("clocksource/arm_arch_timer: Remove use of workaround static key").
This all leaves the jump_label patching code in a funny situation on
arm64 as we do not synchronise with other CPUs to reduce the likelihood
of a bug which no longer exists. Consequently, toggling a static key on
one CPU cannot be assumed to take effect on other CPUs, leading to
potential issues, for example with missing preempt notifiers.
Rather than revert f6cc0c501649 and go back to stop_machine() for each
patch site, implement arch_jump_label_transform_apply() and kick all
the other CPUs with an IPI at the end of patching.
Cc: Alexander Potapenko <glider@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Marc Zyngier <maz@kernel.org> Fixes: f6cc0c501649 ("arm64: Avoid calling stop_machine() when patching jump labels") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20240731133601.3073-1-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
projects / linux.git / log