From 9c7fbebe5dd5d9daa9160b778432daef2a13f47f Mon Sep 17 00:00:00 2001 From: Ye Li Date: Fri, 29 Oct 2021 09:46:25 +0800 Subject: [PATCH] imx8ulp: Workaround LPOSC_TRIM fuse load issue 8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0 LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision. A0.2 will fix the issue in ROM. But A0.1 we have to workaround it in SPL by setting LPOSCCTRL BIASCURRENT again. Reviewed-by: Peng Fan Signed-off-by: Ye Li Signed-off-by: Peng Fan --- arch/arm/include/asm/arch-imx8ulp/sys_proto.h | 1 + arch/arm/mach-imx/imx8ulp/soc.c | 20 +++++++++++++++++++ board/freescale/imx8ulp_evk/spl.c | 6 ++++++ 3 files changed, 27 insertions(+) diff --git a/arch/arm/include/asm/arch-imx8ulp/sys_proto.h b/arch/arm/include/asm/arch-imx8ulp/sys_proto.h index 8e2c6ed0ce..284ccafc98 100644 --- a/arch/arm/include/asm/arch-imx8ulp/sys_proto.h +++ b/arch/arm/include/asm/arch-imx8ulp/sys_proto.h @@ -17,4 +17,5 @@ int xrdc_config_pdac(u32 bridge, u32 index, u32 dom, u32 perm); int xrdc_config_pdac_openacc(u32 bridge, u32 index); enum boot_device get_boot_device(void); void set_lpav_qos(void); +void load_lposc_fuse(void); #endif diff --git a/arch/arm/mach-imx/imx8ulp/soc.c b/arch/arm/mach-imx/imx8ulp/soc.c index d9dca21e8c..e12e28d9e7 100644 --- a/arch/arm/mach-imx/imx8ulp/soc.c +++ b/arch/arm/mach-imx/imx8ulp/soc.c @@ -487,6 +487,26 @@ void lpav_configure(void) writel(0x003fffff, SIM_SEC_BASE_ADDR + 0x58); } +void load_lposc_fuse(void) +{ + int ret; + u32 val = 0, val2 = 0, reg; + + ret = fuse_read(25, 0, &val); + if (ret) + return; /* failed */ + + ret = fuse_read(25, 1, &val2); + if (ret) + return; /* failed */ + + /* LPOSCCTRL */ + reg = readl(0x2802f304); + reg &= ~0xff; + reg |= (val & 0xff); + writel(reg, 0x2802f304); +} + void set_lpav_qos(void) { /* Set read QoS of dcnano on LPAV NIC */ diff --git a/board/freescale/imx8ulp_evk/spl.c b/board/freescale/imx8ulp_evk/spl.c index 42f8e262b6..c17d5eff7d 100644 --- a/board/freescale/imx8ulp_evk/spl.c +++ b/board/freescale/imx8ulp_evk/spl.c @@ -77,6 +77,12 @@ void spl_board_init(void) /* After AP set iomuxc0, the i2c can't work, Need M33 to set it now */ + /* Load the lposc fuse for single boot to work around ROM issue, + * The fuse depends on S400 to read. + */ + if (is_soc_rev(CHIP_REV_1_0) && get_boot_mode() == SINGLE_BOOT) + load_lposc_fuse(); + upower_init(); power_init_board(); -- 2.39.5