This uclass is intended for devices that do not need any features from the
uclass, including binding children.
This will typically be used by devices that are used to bind child devices
but do not use dm_scan_fdt_dev() to do it. That is for example the case of
several USB wrappers that have 2 child devices (1 for device and 1 for
host) but bind only one at a any given time.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 24 Jun 2019 17:05:47 +0000 (19:05 +0200)]
usb: ehci-mx6: Fix bus enumeration for DM case
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Abel Vesa <abel.vesa@nxp.com> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Ludwig Zenz <lzenz@dh-electronics.com> Cc: Lukasz Majewski <lukma@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org>
Kever Yang [Mon, 1 Jul 2019 03:49:14 +0000 (11:49 +0800)]
rockchip: config: tiner-rk3288: extend CONFIG_SYS_MONITOR_LEN to 600KB
The raw u-boot.bin for tinker board has been about 450KB without
debug option, and 550KB with all debug on, and the default value is 200KB,
which is not enough for run raw u-boot.bin.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 1 Jul 2019 03:49:13 +0000 (11:49 +0800)]
rockchip: config: update config for TPL support on tinker-rk3288
We need to update TEXT BASE for TPL/SPL/U-Boot;
SPL no need relocate STACK after enable TPL, so remove it;
Don't enable pinctrl names so that SPL can get pinctrl dts;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 1 Jul 2019 03:49:11 +0000 (11:49 +0800)]
rockchip: dts: tinker: migrate the dm-pre-reloc tag into -u-boot dts
Migrate all the "u-boot,dm-pre-reloc" tag from rk3288-tinker.dts
into rk3288-tinker-u-boot.dtsi.
When both board level and soc level '-u-boot.dtsi' files exist,
we need to include the soc level 'rk3288-u-boot.dtsi' manually.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Mark Kettenis [Fri, 21 Jun 2019 21:16:45 +0000 (23:16 +0200)]
rockchip: dts: rk3399: rockpro64: Provide init voltage
Add missing regulator-init-microvolt property to vdd_log regulator.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Rebase on latest u-boot-rockchip master) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I13b24fb81e8ad269d7dbb0c7b67f5f4795d2e775
Frieder Schrempf [Thu, 27 Jun 2019 07:03:16 +0000 (07:03 +0000)]
spl: atf: Fix uninitialized pointer to bl31_image_info
The pointer to struct atf_image_info in
bl31_params_mem.bl31_params.bl31_image_info is not initialized before
being dereferenced. This can cause U-Boot to crash right before jumping
to the BL31 ATF binary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Fixes: bcc1726a7bdd ("spl: add support to booting with ATF") Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Shawn Guo [Mon, 17 Jun 2019 03:08:34 +0000 (11:08 +0800)]
poplar: increase SYS_MALLOC_F_LEN for DM_FLAG_PRE_RELOC support
There is a regression seen on Poplar platform, which doesn't even show
a U-Boot version banner on booting. It turns out that due to landing
of commit 3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver"), we need to increase SYS_MALLOC_F_LEN from its
default size 0x400, as pre-relocation requires more memory there. Let's
increase SYS_MALLOC_F_LEN to 0x4000 to fix the regression.
Thanks to Andreas Färber <afaerber@suse.de> for reporting, and Bin Meng
<bmeng.cn@gmail.com> for trouble shooting.
Reported-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Andreas Färber <afaerber@suse.de>
Masahiro Yamada [Fri, 28 Jun 2019 17:38:05 +0000 (02:38 +0900)]
ARM: uniphier: remove unused init code for CONFIG_DEBUG_UART
debug_uart_init() is called from spl_board_init(), which is only
compiled for SPL. For U-boot proper, _debug_uart_init() is unreachable,
so dropped by the dead code elimination.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Tom Rini [Fri, 28 Jun 2019 11:59:38 +0000 (07:59 -0400)]
Merge tag 'u-boot-stm32-20190628' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU fixes/cleanup:
- Fix SPL console for STM32F769 Discovery
- Fix Memory Protection Unit size for STM32F4 series
- Cleanup DT for STM32F746 Discovery
Patrice Chotard [Tue, 25 Jun 2019 11:24:03 +0000 (13:24 +0200)]
mach-stm32: Fix MPU region size dedicated to SDRAM for STM32F4
The MPU region dedicated for SDRAM for STM32F4 SoCs family
was set to 16MB, but STM32F429 Evaluation board have 32MB of SDRAM.
When kernel starts, only first 16MB of SDRAM are configured with XN
(eXecute Never) bit disabled, whereas kernel is using 32MB.
To avoid such situation in the future, extend this MPU region to 512MB
as for STM32F7/H7.
It fixes the following user land exception on STM32F429 Evaluation
board :
[ 1.713002] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.722605] devtmpfs: mounted
[ 1.733057] Freeing unused kernel memory: 72K
[ 1.737622] This architecture does not have kernel memory protection.
[ 1.744070] Run /sbin/init as init process
[ 1.906850]
[ 1.906850] Unhandled exception: IPSR = 00000004 LR = fffffffd
[ 1.914282] CPU: 0 PID: 1 Comm: init Not tainted 5.1.0-00002-gcf9ca5719954 #6
[ 1.921433] Hardware name: STM32 (Device Tree Support)
[ 1.926601] PC is at 0x1a00b64
[ 1.929642] LR is at (null)
[ 1.932669] pc : [<01a00b64>] lr : [<00000000>] psr: 01000000
[ 1.938993] sp : 01a5cfb0 ip : 00000000 fp : 00000000
[ 1.944269] r10: 01a43b00 r9 : 00000000 r8 : 00000000
[ 1.949564] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : 00000000
[ 1.956168] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
[ 1.962701] xPSR: 01000000
[ 1.965506] CPU: 0 PID: 1 Comm: init Not tainted 5.1.0-00002-gcf9ca5719954 #6
[ 1.972658] Hardware name: STM32 (Device Tree Support)
[ 1.978132] [<0000c009>] (unwind_backtrace) from [<0000b24f>] (show_stack+0xb/0xc)
[ 1.986024] [<0000b24f>] (show_stack) from [<0000b947>] (__invalid_entry+0x4b/0x4c)
Igor Opaniuk [Mon, 24 Jun 2019 08:39:14 +0000 (11:39 +0300)]
apalis_imx6: increase phy autoneg timeout
Default value (4000ms) of PHY_ANEG_TIMEOUT for Micrel KSZ9031 contoller
isn't sufficient to finish auto-negotiation, which sometimes leads to
timeout errors:
Apalis iMX6 # dhcp
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increase the auto-negotiation time-out to 15000ms.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Marek Vasut [Sun, 9 Jun 2019 16:46:44 +0000 (18:46 +0200)]
ARM: imx: m53menlo: Convert MMC, USB and block to DM
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Marek Vasut [Sun, 9 Jun 2019 16:46:42 +0000 (18:46 +0200)]
ARM: dts: imx: m53menlo: Import M53Menlo DT from Linux
Import iMX53 M53Menlo device tree from Linux next-201906073f310e51ceb1 .
Enable DT control in full U-Boot . Add U-Boot extras into separate DTSi,
the GPIO controllers need to be inited early, otherwise m53_set_clock()
won't be able to detect the correct CPU clock frequency by reading the
GPIO.
According to hab.c code we have to notify the ROM code if the MMU is
enabled or not. This is achieved by setting the "pu_irom_mmu_enabled"
to 0x1.
The current address in hab.c code is wrong for i.MX6SL, according to ROM
map file the correct address is 0x00901c60.
As we are writing in the wrong address the ROM code is not flushing the
caches when needed, and the following HAB event is observed in certain
scenarios:
Update MX6SL_PU_IROM_MMU_EN_VAR to address this issue.
Reported-by: Frank Zhang <frank.zhang@nxp.com> Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Thu, 27 Jun 2019 11:34:14 +0000 (07:34 -0400)]
Merge tag 'rockchip-for-v2019.07-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- new board: rk3328 rock64
- rk3328 SPL support
- rk3399 spl/tpl board init cleanup
- use environment to get ATF binary for rk3399
- build u-boot.itb target by default for rockchip
- rk3399 board init fix after pinctrl patch set merged
Eugen Hristev [Wed, 12 Jun 2019 10:16:18 +0000 (13:16 +0300)]
board: atmel: fix pda variable not being reset
In case someone detects a PDA and u-boot sets the 'pda' variable,
and the user does a saveenv, the pda is set in env, and if the
screen is removed, u-boot will still have in the env the 'pda'
variable, even if no screen is attached.
In order to fix this, we have to reset the 'pda' variable,
such that it's not just set if the screen is detected, but also unset
if no screen is detected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Mark Kettenis [Fri, 21 Jun 2019 20:57:20 +0000 (22:57 +0200)]
rockchip: rk3399: Fix enabling boot-on regulators
The new common rockchip pinctrl driver does not support explicit
requests for a particular pinctrl function. As a result, the
board_init() function bails out early before enabling the boot-on
regulators. Fix this by simply removing the request for pwm0, pwm2
and pwm3. The generic DM code already does the necessary
configuration if necessary.
Reported-by: Levin Du <djw@t-chip.com.cn> Signed-of-by: Mark Kettenis <kettenis@openbsd.org>
Jagan Teki [Thu, 20 Jun 2019 18:55:02 +0000 (00:25 +0530)]
rockchip: rk3399: Move u-boot, dm-pre-reloc of uart0, uart2
u-boot,dm-pre-reloc for uart0, uart2 indeed u-boot specific
properties. Move them into rk3399-u-boot.dtsi so the boards
which enabled these node will available during SPL.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 20 Jun 2019 18:55:00 +0000 (00:25 +0530)]
rockchip: rk3399: Support common spl_board_init
Support common spl_board_init by moving code from puma
board file into, common rk3399-board-spl.c.
Part of the code has sysreset-gpio, regulators_enable_boot_on
but right now only puma board is using this with relevant
config options rest remains common for all targets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 20 Jun 2019 18:54:59 +0000 (00:24 +0530)]
board: rk3399: Drop explicit uart enablement in spl_board_init
preloader_console_init is used for printing SPL boot banner that
usually called from spl_board_init.
The current spl_board_init in evb and rock960 is enabling explicit
pinctrl, debug uart prior to calling preloader_console_init which
eventually not required since board_init_f is already enabled
debug uart.
So, drop those explicit enablement calls from spl_board_init of
evb, rock960.
Tested this by enabling CONFIG_SPL_BOARD_INIT and adding
u-boot,dm-pre-reloc property for uart node.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 20 Jun 2019 10:07:39 +0000 (15:37 +0530)]
board: puma: Get bl31.bin via BL31 and rk3399m0.bin via PMUM0
Right now puma rk3399 board need to copy bl31-rk3399.bin and
rk3399m0.bin into u-boot source directory to make use of building
u-boot.itb.
So, add environment variable
- BL31 for bl31.bin (instead of bl31-rk3399.bin to compatible with other
platform BL31 env)
- PMUM0 for rk3399m0.bin
If the builds are not exporting BL31, PMUM0 env, the fit_spl_atf.sh will
notify with warning about which document to refer for more information
like this:
WARNING: BL31 file bl31.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
WARNING: PMUM0 file rk3399m0.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 20 Jun 2019 10:59:22 +0000 (16:29 +0530)]
rockchip: rk3399: Get bl31.elf via BL31
Right now rockchip platform need to copy bl31.elf into u-boot
source directory to make use of building u-boot.itb.
So, add environment variable BL31 like Allwinner SoC so-that the
bl31.elf would available via BL31.
If the builds are not exporting BL31 env, the make_fit_atf.py
explicitly create dummy bl31.elf in u-boot root directory to
satisfy travis builds and it will show the warning on console as
WARNING: BL31 file bl31.elf NOT found, resulting binary is non-functional
WARNING: Please read Building section in doc/README.rockchip
Note, that the dummy bl31 files were created during not exporting
BL31 case would be removed via clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Tue, 7 May 2019 18:52:12 +0000 (00:22 +0530)]
travis.yml: Add pyelftools install entry
Currently rockchip platform is using explicit 'make u-boot.itb' for
building u-boot.itb but if we enable CONFIG_BUILD_TARGET as 'u-boot.itb'
then the resulting u-boot.itb directly will create by make.
But, that indeed make travis build fail since it require python-pyelftools
host package.
So add pyelftools install entry as 'pip install pyelftools', this would
create pyelftools on travis host which are required to build rk3399 itb.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:52:11 +0000 (00:22 +0530)]
Makefile: clean bl31_*.bin
Rockchip platform has its python script that would generate various
bl31_*bin for creating u-boot.itb file by taking bl31.elf as input.
These bl31_*.bin files are generated in u-boot root directory and
have no rule to clean it up. so add support for it by adding in
command entry of clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Sat, 8 Jun 2019 21:27:15 +0000 (00:27 +0300)]
rockchip: Kconfig: enable SPL support for rk3328
Enable SPL support and some related option in Kconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from https://github.com/rockchip-linux/u-boot/commit/430b01462bf3f24aaf7920ae2587a6943c39ab5d with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Kever Yang [Sat, 8 Jun 2019 21:27:14 +0000 (00:27 +0300)]
rockchip: rk3328: add SPL support
Add SPL support for rk3328, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from https://github.com/rockchip-linux/u-boot/commit/cb2b7a1bc75ebb116b1eb9b0ae0223e84d86fc4b with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Sat, 8 Jun 2019 21:27:13 +0000 (00:27 +0300)]
rockchip: rk3328: add SPL board file support
rk3328 SPL is locate at dram, so do not have strict size limit,
suppose to enable storage media controller driver, load ATF and
U-Boot, then boot into ATF.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from https://github.com/rockchip-linux/u-boot/commit/4ebe3968b683190cb8e5741aa7227b4fa7497874 with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Fri, 21 Jun 2019 18:12:28 +0000 (14:12 -0400)]
Merge tag 'efi-2019-07-rc5-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5 (3)
This pull request provides error fixes for the graphical output protocol,
the text output protocol, and the extended text input protocol.
Setting the boot device for the bootefi command is now not only supported
by the 'load' command but also for the file system specific commands like
'fatload'.
Tom Rini [Fri, 21 Jun 2019 18:11:11 +0000 (14:11 -0400)]
Merge branch '2019-06-21-master-imports'
- Assorted small fixes
- Bugfix RSA handling code to reject images with unknown padding.
- Some boards disabled unused features to turn off DM warnings.
Peng Fan [Thu, 6 Jun 2019 07:59:16 +0000 (07:59 +0000)]
lib: Makefile: build fdtdec_common.c when OF_LIBFDT selected
When build SPL_OF_PLATDATA on i.MX6, meet issue the fdtdec_get_int
not defined, however fdtdec.c will use fdtdec_get_int, so let's
compile fdtdec_common.c when OF_LIBFDT selected.
Since there is also SPL_OF_LIBFDT, so need to use
CONFIG_$(SPL_TPL_)OF_LIBFDT.
Bin Meng [Wed, 5 Jun 2019 14:26:44 +0000 (07:26 -0700)]
pci: Avoid assigning PCI resources that are below 0x1000
commit b7598a43f2b4 ("[PATCH] Avoid assigning PCI resources from
zero address") only moved the bus lower address to 0x1000 if the
given bus start address is zero. The comment said 0x1000 is a
reasonable starting value, hence we'd better apply the same
adjustment when the given bus start address is below 0x1000.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Joshua Watt [Thu, 20 Jun 2019 21:31:35 +0000 (16:31 -0500)]
config_distro_bootcmd: Init IDE devices
IDE devices are no longer automatically probed by u-boot, so it should
be done by the distro boot command before attempting to boot from IDE
(just like scsi and nvme)
Robert Hancock [Tue, 18 Jun 2019 15:53:04 +0000 (09:53 -0600)]
disk: part: Don't skip partition init
blk_get_device_by_str was skipping part_init when hw partition 0 was
selected because it is the default. However, this caused issues when
switching to a non-zero partition and then back to partition zero, as
stale data from the wrong partition was returned.
Remove this optimization and call part_init regardless of the selected
partition.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
projects / u-boot.git / log