Icenowy Zheng [Mon, 1 May 2017 06:31:57 +0000 (14:31 +0800)]
sunxi: enable SATA on Banana Pi M2 Ultra
Banana Pi M2 Ultra has a SATA port connected to the internal SATA
controller of R40 SoC. The controller's 1.2v VDD is connected to ELDO3
and the 2.5v VDD is connected to DLDO4.
Enable these regulators as well as the SATA support of Banana Pi M2
Ultra, by adding needed config lines into its defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Icenowy Zheng [Mon, 1 May 2017 06:31:56 +0000 (14:31 +0800)]
sunxi: add clock configuration of R40 sata
R40 has a similar SATA controller with the ones on A10/A20, but with a
reset line added (like other peripherals on sun6i+), and two extra VDD
pins added (1.2v and 2.5v).
Add clock configuration of R40 SATA.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jernej Skrabec [Mon, 27 Mar 2017 17:22:33 +0000 (19:22 +0200)]
sunxi: Disable DE2 video driver where not needed
Because DE2 driver is enabled by default, it is nice to disable it on
all boards which don't have any video output. List of such boards is
also much shorter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits enable DM I2C support for A64/H3/H5 SoCs.
It is not enabled globaly for all sunxi SoCs, because some boards use
PMICs which are connected through I2C. In order to keep same
functionality, PMIC drivers needs to be ported to DM too.
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
sunxi: power: Compile sy8106a driver only during SPL build
Driver for that regulator is used only in SPL and it uses old I2C
interface. If we want to use DM I2C in U-Boot proper, compilation of
this driver has to be limited only to SPL.
Andreas Färber [Fri, 14 Apr 2017 16:44:47 +0000 (18:44 +0200)]
sunxi: Fix arm64 fdtfile variable
Currently $fdtfile is constructed from CONFIG_DEFAULT_TREE, containing
the filename. However on arm64 that file is located in an allwinner
subdirectory.
To avoid the need for users/distros symlinking the .dtb files, prepend
the vendor directory for ARM64.
This aligns Pine64 with other boards such as Raspberry Pi 3.
Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jernej Skrabec [Mon, 27 Mar 2017 17:22:30 +0000 (19:22 +0200)]
sunxi: video: Convert lcdc to use struct display_timing
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 1 Mar 2017 03:03:15 +0000 (11:03 +0800)]
sunxi: Add PSCI support for R40
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 1 Dec 2016 11:09:57 +0000 (19:09 +0800)]
sunxi: Use H3/A64 DRAM initialization code for R40
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 30 Nov 2016 08:58:35 +0000 (16:58 +0800)]
sunxi: Provide defaults for R40 DRAM settings
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 30 Nov 2016 08:54:34 +0000 (16:54 +0800)]
sunxi: Set PLL lock enable bits for R40
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 2 Mar 2017 08:03:06 +0000 (16:03 +0800)]
sunxi: Split up long Kconfig lines
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB_EHCI configuration is already set in this defconfig
using kconfig's config. This configuration in SYS_EXTRA_OPTIONS
must be removed and so the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Philipp Tomsich [Sat, 1 Apr 2017 10:59:25 +0000 (12:59 +0200)]
rockchip: rk3399: spl: add UART0 support for SPL
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).
To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.
As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.
As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.
With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
when enable PMIC rk808,the system will halt at very
early stage,log is shown as bellow.
INFO: plat_rockchip_pmu_init(1211): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
time 44561b, 0 (<<----Just stop here)
It's caused by the absence of "{ }" in syscon_rk3399.c
,which will lead to memory overflow like below.According
to Sysmap file ,we can find the function buck_get_value
of rk808 is just follow the compatible struct,the pointer
"of_match" point to "buck_get_value",but it is not a
struct and don't have member of compatible, In this case,
system crash. So,on the face, it looks like that rk808 is
guilty.but he is really innocent.
while (of_match->compatible) { <<----------
if (!strcmp(of_match->compatible, compat)) {
*of_idp = of_match;
return 0;
}
of_match++;
}
Signed-off-by: Eric Gao <eric.gao@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Kever Yang <kever.yang@rock-chips.com>
Klaus Goger [Fri, 7 Apr 2017 17:13:38 +0000 (19:13 +0200)]
rockchip: ARM64: split RK3399-Q7 board off the RK3399-EVB board
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399: Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
rockchip: sysreset: rk3188: Make sure remap is off on warm-resets
The warm-reset of rk3188 socs keeps the remap setting as it was, so if
it was enabled, the cpu would start from address 0x0 of the sram instead
of address 0x0 of the bootrom, thus making the reset hang.
Therefore make sure the remap is disabled before attempting a warm reset.
Cold reset is not affected by this at all.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
Most Rockchip socs have the ability to either map the bootrom or a sram
area to the starting address of the cpu by flipping a bit in the GRF.
Newer socs leave this untouched and mapped to the bootrom but the legacy
loaders on rk3188 and before enabled the remap functionality and the
current smp implementation in the Linux kernel also requires it to be
enabled, to bring up secondary cpus.
So to keep smp working in the kernel, mimic the behaviour of the legacy
bootloaders and enable the remap functionality.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Glass <sjg@chromium.org>
Eddie Cai [Sat, 1 Apr 2017 06:49:54 +0000 (14:49 +0800)]
rockchip: Add USB to the default boot targets
Now that most rockchip SoC based board have usb host support, enable
USB boot targets by default.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Fixed build errors when CONFIG_CMD_USB not defined: Signed-off-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Wed, 29 Mar 2017 19:20:28 +0000 (21:20 +0200)]
rockchip: spl: rk3399: disable DDR security regions for SPL
The RK3399 hangs during DMA of the Designware MMC controller, when
performing DMA-based transactions in SPL due to the DDR security settings
left behind by the BootROM (i.e. accesses to the first MB of DRAM are
restricted... however, the DMA is likely to target this first MB, as it
transfers from/to the stack).
System security is not affected, as the final security configuration is
performed by the ATF, which is executed after the SPL stage.
With this fix in place, we can now drop 'fifo-mode' in the DTS for the
RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 14 Apr 2017 00:51:46 +0000 (08:51 +0800)]
board: sama5d3_xplained: Clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 14 Apr 2017 00:51:45 +0000 (08:51 +0800)]
board: sama5d3_xplained: Update to support DM/DT
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc: Signed-off-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 14 Apr 2017 00:51:43 +0000 (08:51 +0800)]
board: sama5d3xek: Clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch: Signed-off-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 14 Apr 2017 00:51:42 +0000 (08:51 +0800)]
board: sama5d3xek: Update to support DM/DT
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 10 Apr 2017 17:34:54 +0000 (11:34 -0600)]
dm: led: Adjust the LED uclass
At present this is very simple, supporting only on and off. We want to
also support toggling and blinking. As a first step, change the name of
the main method and use an enum to indicate the state.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ziping Chen <techping.chan@gmail.com>
With DM_SCSI enabled, blk_create_devicef() is called with blkz = 0, leading
to a divide-by-0 exception.
scsi_detect_dev() can be used to get the required parameters (block size
and number of blocks) from the drive before calling blk_create_devicef().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
scsi: make the LUN a parameter of scsi_detect_dev()
This is a cosmetic change. target and LUN have kind of the same role in
this function. One of them was passed as a parameter and the other was
embedded in a structure. For consistency, pass both of them as parameters.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 14 Apr 2017 14:06:28 +0000 (10:06 -0400)]
buildman: Translate more strings to latin-1
When writing out some of our results we may now have UTF-8 characters
in there as well. Translate these to latin-1 and ignore any errors (as
this is for diagnostic and given the githash anything else can be
reconstructed by the user.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
### ERROR ### Please RESET the board ###
Eddie Cai [Thu, 6 Apr 2017 03:37:04 +0000 (11:37 +0800)]
usb: dwc2: invalidate the dcache before starting the DMA
We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com> Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Philipp Tomsich [Thu, 6 Apr 2017 14:58:53 +0000 (16:58 +0200)]
usb: dwc3: gadget: make cache-maintenance on event buffers more robust
Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).
The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
# during initialisation:
1. allocate buffers via memalign
=> buffers may still be modified (cached, dirty)
# during interrupt processing
2. clean + invalidate buffers
=> may commit stale data from a modified cacheline
3. read from buffers
This could lead to garbage info being written to buffers before
reading them during even-processing.
To make the event processing more robust, we use the following sequence
for the cache-maintenance:
# during initialisation:
1. allocate buffers via memalign
2. clean + invalidate buffers
(we only need the 'invalidate' part, but dwc3_flush_cache()
always performs a 'clean + invalidate')
# during interrupt processing
3. read the buffers
(we know these lines are not cached, due to the previous
invalidation and no other code touching them in-between)
4. clean + invalidate buffers
=> writes back any modification we may have made during event
processing and ensures that the lines are not in the cache
the next time we enter interrupt processing
Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Thu, 6 Apr 2017 14:58:52 +0000 (16:58 +0200)]
usb: dwc3: ensure consistent types for dwc3_flush_cache
The dwc3_flush_cache() call was declared and used inconsistently:
* The declaration assumed 'int' for addresses (a potential issue
when running in a LP64 memory model).
* The invocation cast the address to 'long'.
This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Felipe Balbi [Wed, 22 Feb 2017 15:12:40 +0000 (17:12 +0200)]
usb: gadget: g_dnl: only set iSerialNumber if we have a serial#
We don't want to claim that we support a serial number string and
later return nothing. Because of that, if g_dnl_serial is an empty
string, let's skip setting iSerialNumber to a valid number.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Wed, 22 Feb 2017 15:12:39 +0000 (17:12 +0200)]
usb: gadget: g_dnl: hold maximum string descriptor
A USB String descriptor can be up to 255 characters long and it's not
NULL terminated according to the USB spec. This means our
MAX_STRING_SERIAL should be 256 (to cope with NULL terminator).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Checking the source code, we found that the variable "pixels"
gets a wrong value:
int pixels = VIDEO_FONT_HEIGHT * vid_priv->line_length;
"pixels" here means the value of pixels for a character, rather
than the bytes for a character. So the variable "pixels" is 4
times bigger than it's exact value, which will cause the memory
overflow when the cpu runs the following code:
Kever Yang [Fri, 10 Mar 2017 04:05:14 +0000 (12:05 +0800)]
usb: dwc2: add support for external vbus supply
Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Simon Glass <sjg@chromium.org>
arm: socfpga: sr1500 use environment in common header
This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
arm: socfpga: Socrates use environment in common header
This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: SoCKit use environment in common header
This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: DE1 use environment in common header
This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in V2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
arm: socfpga: C5 SoCDK use environment in common header
This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: A5 SoCDK use environment in common header
This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Add support to boot from the custom a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v3:
- Fix small typo in defconfig, missing "C"
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- Fix dtb name
projects / u-boot.git / log