sf: bar: Clean BA24 Bank Address Register bit after read/write/erase operation
The content of Bank Address Register (BAR) is volatile. It is cleared
after power cycle or reset command (RESET F0h).
Some memories (like e.g. s25fl256s) use it to access memory larger than
0x1000000 (16 MiB).
The problem shows up when one:
1. Reads/writes/erases memory > 16 MiB
2. Calls "reset" u-boot command (which is not causing BAR to be cleared)
In the above scenario, the SoC ROM sends 0x000000 address to read SPL.
Unfortunately, the BA24 bit is still set and hence it receives content
from 0x1000000 (16 MiB) memory address.
As a result the SoC aborts and we hang. Only power cycle can take the
SoC out of this state.
How to reproduce/test:
sf probe; sf erase 0x1200000 0x800000; reset
sf probe; sf erase 0x1200000 0x800000; sf write 0x11000000 0x1200000 0x800000; reset
sf probe; sf read 0x11000000 0x1200000 0x800000; reset
Signed-off-by: Lukasz Majewski <lukma@denx.de>
[Fixed comment text on clean_bar function] Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Fri, 22 Sep 2017 21:57:22 +0000 (22:57 +0100)]
SPL: SPI: sunxi: add SPL FIT image support
The sunxi-specific SPI load routine only knows how to load a legacy
U-Boot image.
Teach it how to handle FIT images as well, simply by providing the
existing SPL FIT loader with the right loader routine to access the SPI
NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Peter Kosa <kope@madnet.sk> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Suresh Gupta [Mon, 5 Jun 2017 09:07:20 +0000 (14:37 +0530)]
spi: fsl_qspi: Copy 16 byte aligned data in TX FIFO
In some of the QSPI controller version, there must be atleast
128bit data available in TX FIFO for any pop operation otherwise
error bit will be set. The code will not make any behavior change
for previous controller as the transfer data size in ipcr register
is still the same.
Patch is tested on LS1046A which do not require 16 bytes aligned and
LS1088A which require 16 bytes aligned data in TX FIFO
Spansion S25FS256S and S25FL256S flashes have equal JEDEC ID and ext ID.
As far as S25FL256S occures in spi_flash_ids before S25FS256S, U-Boot
incorrectly detects FS flash as FL. Thus its better to compare with
S25FS256S first.
Signed-off-by: Vsevolod Gribov <vgribov@larch-networks.com>
[Added S-o-b] Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Yogesh Gaur [Thu, 31 Aug 2017 04:56:31 +0000 (10:26 +0530)]
mtd/spi: Add MT35XU512ABA1G12 NOR flash support
Add MT35XU512ABA1G12 parameters to NOR flash parameters array.
The MT35XU512ABA1G12 only supports 1 bit mode and 8 bits. It can't support
dual and quad. Supports subsector erase with 4KB granularity, have support
of FSR(flag status register) and flash size is 64MB.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Suresh Gupta [Wed, 30 Aug 2017 14:36:33 +0000 (20:06 +0530)]
spi: fsl_qspi: Add controller busy check before new spi operation
It is recommended to check either controller is free to take
new spi action. The IP_ACC and AHB_ACC bits indicates that
the controller is busy in IP or AHB mode respectively.
And the BUSY bit indicates that controller is currently
busy handling a transaction to an external flash device
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini [Sun, 24 Sep 2017 03:14:33 +0000 (23:14 -0400)]
tools/mkimage: Make the path to the dtc binary that mkimage calls configurable
In some cases, such as FreeBSD, the path to an alternative dtc needs to
be used. Rather than override the one given in the Makefile on the
command line, make this part of the build configuration.
Tom Rini [Sat, 23 Sep 2017 17:00:57 +0000 (13:00 -0400)]
dtc: Switch to building and using our own dtc unless provided
This makes us act like the Linux Kernel does and allow for dtc to be
provided externally but otherwise we use the version of dtc that is
included in the sources. This in turn means that we can drop the
checkdtc logic. We select DTC in the cases where we will need the dtc
tool provided.
fe50bd1ecc1d fdtget: Split out cell list display into a new function 62d812308d11 README: Add a note about test_tree1.dts 5bed86aee9e8 pylibfdt: Add support for fdt_subnode_offset() 46f31b65b3b3 pylibfdt: Add support for fdt_node_offset_by_phandle() a3ae43723687 pylibfdt: Add support for fdt_parent_offset() a198af80344c pylibfdt: Add support for fdt_get_phandle() b9eba92ea50f tests: Return a failure code when any tests fail 155faf6cc209 pylibfdt: Use local pylibfdt module 50e5cd07f325 pylibfdt: Add a test for use of uint32_t ab78860f09f5 pylibfdt: Add stdint include to fix uint32_t 36f511fb1113 tests: Add stacked overlay tests on fdtoverlay 1bb00655d3e5 fdt: Allow stacked overlays phandle references a33c2247ac8d Introduce fdt_setprop_placeholder() method 0016f8c2aa32 dtc: change default phandles to ePAPR style instead of both e3b9a9588a35 tests: fdtoverlay unit test 42409146f2db fdtoverlay: A tool that applies overlays aae22722fc8d manual: Document missing options 13ce6e1c2fc4 dtc: fix sprintf() format string error, again d990b8013889 Makefile: Fix build on MSYS2 and Cygwin 51f56dedf8ea Clean up shared library compile/link options 21a2bc896e3d Suppress expected error message in fdtdump test 2a42b14d0d03 dtc: check.c fix compile error a10cb3c818d3 Fix get_node_by_path string equality check 548aea2c436a fdtdump: Discourage use of fdtdump c2258841a785 fdtdump: Fix over-zealous version check 9067ee4be0e6 Fix a few whitespace and style nits e56f2b07be38 pylibfdt: Use setup.py to build the swig file 896f1c133265 pylibfdt: Use Makefile constructs to implement NO_PYTHON 90db6d9989ca pylibfdt: Allow setup.py to operate stand-alone e20d9658cd8f Add Coverity Scan support b04a2cf08862 pylibfdt: Fix code style in setup.py 1c5170d3a466 pylibfdt: Rename libfdt.swig to libfdt.i 580a9f6c2880 Add a libfdt function to write a property placeholder ab15256d8d02 pylibfdt: Use the call function to simplify the Makefile 9f2e3a3a1f19 pylibfdt: Use the correct libfdt version in the module e91c652af215 pylibfdt: Enable installation of Python module 8a892fd85d94 pylibfdt: Allow building to be disabled 741cdff85d3e .travis.yml: Add builds with and without Python library prerequisites 14c4171f4f9a pylibfdt: Use package_dir to set the package directory 89a5062ab231 pylibfdt: Use environment to pass C flags and files 4e0e0d049757 pylibfdt: Allow pkg-config to be supplied in the environment 6afd7d9688f5 Correct typo: s/pylibgfdt/pylibfdt/ 756ffc4f52f6 Build pylibfdt as part of the normal build process 8cb3896358e9 Adjust libfdt.h to work with swig b40aa8359aff Mention pylibfdt in the documentation 12cfb740cc76 Add tests for pylibfdt 50f250701631 Add an initial Python library for libfdt cdbb2b6c7a3a checks: Warn on node name unit-addresses with '0x' or leading 0s 4c15d5da17cc checks: Add bus checks for simple-bus buses 33c3985226d3 checks: Add bus checks for PCI buses
Tom Rini [Sat, 23 Sep 2017 21:30:53 +0000 (17:30 -0400)]
scripts/dtc: Update to upstream version v1.4.4
This adds the following commits from upstream:
558cd81bdd43 dtc: Bump version to v1.4.4 c17a811c62eb fdtput: Remove star from value_len documentation 194d5caaefcb fdtget: Use @return to document the return value d922ecdd017b tests: Make realloc_fdt() really allocate *fdt 921cc17fec29 libfdt: overlay: Check the value of the right variable 9ffdf60bf463 dtc: Simplify asm_emit_string() implementation 881012e44386 libfdt: Change names of sparse helper macros bad5b28049e5 Fix assorted sparse warnings 672ac09ea04d Clean up gcc attributes 49300f2ade6a dtc: Don't abuse struct fdt_reserve_entry
Tom Rini [Sat, 23 Sep 2017 16:52:44 +0000 (12:52 -0400)]
scripts/dtc: Update to upstream version v1.4.3
Using the update-dtc-source.sh script from Linux v4.14-rc1 import the
portions of dtc that we require. We bring in update-dtc-source.sh and
scripts/dtc/Makefile from Linux v4.14-rc1. Rework DTC_FLAGS handling to
not require a test.
Frank Kunz [Tue, 8 Aug 2017 16:18:29 +0000 (18:18 +0200)]
arm: socfpga: Configuration for EFI boot on DE0-nano-SoC
For EFI boot GPT partition table support is needed as well
as the part command and also the SPL needs to fallback to
other boot methods after parse the SPL header.
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Yangbo Lu [Fri, 15 Sep 2017 01:51:58 +0000 (09:51 +0800)]
armv8: ls1043a: disable IFC in SPL only when QSPI is used
Current u-boot disables IFC support for SD boot on all ls1043a
boards. Actually IFC only conflicts with QSPI on ls1043a hardware.
Only when QSPI is used, IFC should be disabled. Otherwise,
the u-boot with ls1043aqds_sdcard_ifc_defconfig would not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
As per current implementation, default value of board env is
based on board filename i.e ls2080ardb.
With distro support changes, this env is used to decide upon
kernel dtb which is different for other SoCs (ls2088a, ls2081a)
combination supported with this board.
Add support to modify board env at runtime based on SoC type
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Tue, 29 Aug 2017 09:50:37 +0000 (15:20 +0530)]
board/ls2080ardb: Add mcmemsize variable in default env
For most of ls2080ardb use-cases, mc private DRAM block is required
to be of 1.75GB.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: this reservation needs to be reduced if memory is not enough] Reviewed-by: York Sun <york.sun@nxp.com>
Santan Kumar [Fri, 18 Aug 2017 09:50:32 +0000 (15:20 +0530)]
board/ls2081ardb: Update QSPI flash type from n25q512a to s25fs512s
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_DISPLAY_BOARDINFO_LATE config is used to delay
the prints of boardinfo late in cycle during uboot boot.
This feature is not required in case of QSPI_BOOT.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Felix Brack [Thu, 14 Sep 2017 12:37:08 +0000 (14:37 +0200)]
arm: am33xx: Make pin multiplexing functions optional
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: DTS: stm32: adapt stm32h7 dts files for U-boot
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
This patch adds the support of reset and clock control
block (rcc) found on STM32 SoCs.
This driver is similar to a MFD linux driver.
This driver supports currently STM32H7 only.
STM32F4 and STM32F7 will be migrated to this rcc MFD driver
in the future to uniformize all STM32 SoCs already upstreamed.
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
ARM: dts: STiH410: set DWC3 dual role mode to peripheral
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 22 Sep 2017 11:37:43 +0000 (07:37 -0400)]
fs/fat: Reduce stack usage
We have limited stack in SPL builds. Drop itrblock and move to
malloc/free of itr to move this off of the stack. As part of this fix a
double-free issue in fat_size().
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.
Dennis Gilmore [Thu, 24 Aug 2017 15:49:43 +0000 (10:49 -0500)]
detect and setup solidrun hummingboard2
The hummingboard2 is slightly different to the cubox i and to the
hummingboard. The GPIO pin info to probe came from solidruns
for of u-boot on github.
https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589
I have tested on a hummingboard-edge witha imx6 solo and 512mb of
ram.
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Kever Yang [Thu, 7 Sep 2017 03:20:51 +0000 (11:20 +0800)]
rockchip: ram: rk3399: update reg map for of-platdata
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 7 Sep 2017 03:20:50 +0000 (11:20 +0800)]
rockchip: sdhci: update reg map for of-platdata
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 14 Aug 2017 17:05:33 +0000 (19:05 +0200)]
rockchip: dts: rk3368: reduce the number of nodes seen in TPL
The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes. This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Mon, 14 Aug 2017 17:05:32 +0000 (19:05 +0200)]
rockchip: rk3368: adjust DMC driver for 32/64bit-aware OF_PLATDATA
With the new 32/64bit-aware dtoc, the type of reg is fdt64_t and the
OF_PLATDATA structure layout changes. This adjusts the DMC driver for
the RK3368 to track these changes.
For the time being (i.e. until regmap_init_mem_platdata works for the
64bit case), we won't use regmap_init_mem_platdata here and simply
access of_plat.reg[] directly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Mon, 14 Aug 2017 17:05:31 +0000 (19:05 +0200)]
rockchip: timer: update for 32/64bit-aware OF_PLATDATA
With dtoc emitting fdt64_t for addresses (and region sizes), the array
indices for accessing the reg[] array needs to be adjusted. This
adjusts the Rockchip DM timer driver to correctly handle OF_PLATDATA
given this new structure layout.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Tue, 12 Sep 2017 15:30:57 +0000 (17:30 +0200)]
rockchip: dts: rk3399-puma: replace 'rockchip, vbus-gpio' with fixed regulator
On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.
References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus" Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Tue, 12 Sep 2017 15:30:56 +0000 (17:30 +0200)]
rockchip: clk: rk3399: add clk_enable function and support USB HOST0/1
The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.
This implements a minimal clk_enable for the RK3399 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Andy Yan [Mon, 4 Sep 2017 12:32:58 +0000 (20:32 +0800)]
rockchip: rk3368: add the missing target and pinctrl config for sheep board
Add the missing target and pinctrl config for rk3368 sheep board
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Andy Yan [Mon, 4 Sep 2017 12:32:23 +0000 (20:32 +0800)]
rockchip: rk3368: add ENV_MEM_LAYOUT to extra env settings
Add the ENV_MEM_LAYOUT_SETTINGS to CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jagan Teki [Tue, 12 Sep 2017 11:45:47 +0000 (17:15 +0530)]
rk3288: Add Vyasa initial board support
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Tue, 29 Aug 2017 16:24:05 +0000 (18:24 +0200)]
rockchip: rk3399: spl: remove hard-coded addresses for GRF and SGRF
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).
This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.
In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
included in front)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Mon, 11 Sep 2017 20:04:27 +0000 (22:04 +0200)]
rockchip: lion-rk3368: defconfig: resync w/ OF_LIVE and BOOTSTAGE enabled
This adds OF_LIVE and BOOTSTAGE support for the RK3368-uQ7 and
regenerates the defconfig (picking up a few changes/reorderings) from
upstream Kconfig changes.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Remove a comment claiming that this driver only supports the RK3288,
as we also use it on the RK3368, RK3399 and (most likely) on other
variants.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rk_gpio.c
Philipp Tomsich [Mon, 11 Sep 2017 20:04:24 +0000 (22:04 +0200)]
rockchip: gpio: convert to livetree
Update the Rockchip GPIO-bank driver to support a live tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rk_gpio.c
Philipp Tomsich [Mon, 11 Sep 2017 20:04:22 +0000 (22:04 +0200)]
rockchip: rk8xx: remove unused header includes
Remove header file includes that have been left over after the
conversion to livetree-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 11 Sep 2017 20:04:21 +0000 (22:04 +0200)]
rockchip: sdhci: Convert to livetree
Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_sdhci.c
Philipp Tomsich [Mon, 11 Sep 2017 20:04:20 +0000 (22:04 +0200)]
rockchip: spi: Convert to livetree
Update the Rockchip SPI driver to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 11 Sep 2017 20:04:19 +0000 (22:04 +0200)]
rockchip: pinctrl: rk3368: Convert to livetree
Update the pinctrl driver for the RK3368 to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot.git / log