Stefan Roese [Thu, 20 Aug 2020 05:21:56 +0000 (07:21 +0200)]
mips: octeon: lowlevel_init.S: Add NMI handling code for SMP Linux booting
This patch adds the necessary lowlevel init code, to enable SMP Linux
booting. This code will be used with the platform specific Octeon Linux
boot command "bootoctlinux", which starts a configurable number of cores
into Linux.
Additionally some erratas and lowlevel register initializations are
copied from the original Cavium / Marvell U-Boot source code, enabling
booting into the Linux kernel.
Stefan Roese [Mon, 24 Aug 2020 11:04:41 +0000 (13:04 +0200)]
mips: octeon: cache.c: Flush all pending writes in flush_dcache_range()
As noticed while working on the USB xHCI support, Octeon needs to flush
all pending writes so that the values are present in the memory. Add
this "syncw" instruction (twice) to flush_dcache_range().
Stefan Roese [Mon, 24 Aug 2020 11:04:37 +0000 (13:04 +0200)]
usb: xhci: xhci_bulk_tx: Don't "BUG" when comparing addresses
Octeon uses mapped addresses for virtual and physical memory. It's not
that easy to calculate the resulting addresses here. So let's remove
this BUG_ON() completely, as it's not really helpful.
Please also note, that BUG_ON() is not recommended any more in the Linux
kernel.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de>
Stefan Roese [Mon, 24 Aug 2020 11:04:36 +0000 (13:04 +0200)]
usb: xhci: xhci-dwc3.c: Use dev_remap_addr() instead of dev_get_addr()
On MIPS platforms, mapping of the base address is needed. This patch
switches from dev_get_addr() to dev_remap_addr() to get the mapped base
address of the xHCI controller.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de>
Stefan Roese [Wed, 2 Sep 2020 06:29:10 +0000 (08:29 +0200)]
mips: octeon: octeon_ebb7304: Add DDR4 support
This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Stefan Roese [Wed, 2 Sep 2020 06:29:09 +0000 (08:29 +0200)]
mips: octeon: dram.c: Add RAM driver support
This patch adds the initialization call for the Octeon RAM driver to
the Octeon platforms code. So if enabled via Kconfig, the DDR driver
will be called and the RAM will be configured and used. If the RAM
driver is not enabled, the L2 cache is still used as RAM.
Aaron Williams [Wed, 2 Sep 2020 06:29:08 +0000 (08:29 +0200)]
ram: octeon: Add MIPS Octeon3 DDR4 support (part 3/3)
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 3 includes the DIMM SPD handling code and the Kconfig / Makefile
integration.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Wed, 2 Sep 2020 06:29:07 +0000 (08:29 +0200)]
ram: octeon: Add MIPS Octeon3 DDR4 support (part 2/3)
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 2 includes the very complex Octeon 3 DDR4 configuration
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Wed, 2 Sep 2020 06:29:06 +0000 (08:29 +0200)]
ram: octeon: Add MIPS Octeon3 DDR4 support (part 1/3)
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 1 adds the base U-Boot RAM driver, which will be instantiated by
the DT based probing.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Tue, 6 Oct 2020 12:36:38 +0000 (08:36 -0400)]
Merge tag 'efi-2021-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc1
The following bugs in the UEFI system are resolved:
* illegal free in EFI_LOAD_FILE2_PROTOCOL implementation
* incorrect documentation of EFI_LOAD_FILE2_PROTOCOL implementation
* output of CRC32 as decimal instead hexadecimal in unit test
* use EfiReservedMemoryType for no-map reserved memory
* avoid unnecessary resets in UEFI unit tests
* call EFI bootmgr even without having /EFI/boot
Tom Rini [Tue, 6 Oct 2020 12:36:10 +0000 (08:36 -0400)]
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
efi_loader: consider no-map property of reserved memory
The device tree may contain a /reserved-memory node. The no-map property
of the sub-nodes signals if the memory may be accessed by the UEFI payload
or not.
In the EBBR specification (https://github.com/arm-software/ebbr) the
modeling of the reserved memory has been clarified.
If a reserved memory node in the device tree has the no-map property map,
create a EfiReservedMemoryType memory map entry else use
EfiBootServicesData.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_EFI_GRUB_ARM32 is only needed for architectures with caches that are
not managed via CP15 (or for some outdated buggy versions of GRUB). It
makes more sense to disable the setting per architecture than per defconfig.
Move QEMU's CONFIG_EFI_GRUB_ARM32_WORKAROUND=n from defconfig to Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Michael Walle [Tue, 29 Sep 2020 06:54:48 +0000 (08:54 +0200)]
distro_bootcmd: call EFI bootmgr even without having /EFI/boot
Currently, the EFI bootmgr is only called if there is a EFI binary
inside the path for removable media is found, i.e. /EFI/boot/. This
doesn't make sense. It is the duty of the bootmgr to find out the
path and name of the EFI binary to boot. It should be called even
if there is no /EFI/boot directory.
Thus, call the bootmgr before we try to boot the EFI binary inside
the removable media path.
Also remove the ${fdtcontroladdr} parameter because the fallback is
handled in cmd/bootefi.c and that already takes care of correct settings
if the board has ACPI and thus no device tree at all.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
U-Boot offers a EFI_LOAD_FILE2_PROTOCOL which the Linux EFI stub can use to
load an initial RAM disk. Update the function comments of the
implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Neil Armstrong [Thu, 1 Oct 2020 08:04:56 +0000 (10:04 +0200)]
pwm: Add driver for Amlogic Meson PWM controller
This adds the driver for the PWM controller found in the Amlogic SoCs.
This PWM is only a set of Gates, Dividers and Counters:
PWM output is achieved by calculating a clock that permits calculating
two periods (low and high). The counter then has to be set to switch after
N cycles for the first half period.
The hardware has no "polarity" setting. This driver reverses the period
cycles (the low length is inverted with the high length) for
PWM_POLARITY_INVERSED.
Disabling the PWM stops the output immediately (without waiting for the
current period to complete first).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Mon, 21 Sep 2020 07:34:15 +0000 (09:34 +0200)]
board: amlogic: vim3: add support for dynamic PCIe enable
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
Neil Armstrong [Mon, 21 Sep 2020 07:34:14 +0000 (09:34 +0200)]
configs: vim3: use the vim3 board support
Use the newly added VIM3 board support instead of the generic W400.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Mon, 21 Sep 2020 07:34:13 +0000 (09:34 +0200)]
board: amlogic: add a vim3 specific board support
The VIM3 will need a specific code to enable PCIe if enabled in the MCU,
thus add a specific board support for VIM3 & VIM3L.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Mon, 21 Sep 2020 07:34:12 +0000 (09:34 +0200)]
ARM: dts: sync amlogic G12A/SM1 DT from Linux 5.9-rc1
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Thu, 10 Sep 2020 08:48:15 +0000 (10:48 +0200)]
phy: meson-gxl: remove invalid USB3 PHY driver
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Thu, 10 Sep 2020 08:48:13 +0000 (10:48 +0200)]
usb: dwc3: add Amlogic GXL & GXL DWC3 Glue
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tom Rini [Mon, 5 Oct 2020 14:54:27 +0000 (10:54 -0400)]
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
pinctrl: bcm283x: Read address from DT in ofdata_to_platdata
Factor out reading IP base address to ofdata_to_platdata function, which
is designed for this purpose. Also, drop the dev->priv NULL check, since
this is already done by the dm core when allocating space using
priv_auto_alloc_size feature. (in drivers/core/device.c ->
device_ofdata_to_platdata).
Add test on the size of ofnode_phandle_args result to avoid access
to uninitialized elements in args[] field.
This patch avoids the issue when gpio-ranges cell size is not 3 as
expected, for example:
gpio-ranges = <&pinctrl 0>;
instead of
gpio-ranges = <&pinctrl 0 112 16>;
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Soeren Moch [Thu, 27 Aug 2020 19:52:46 +0000 (21:52 +0200)]
board: tbs2910: Use recommended distroboot addresses
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Marek Vasut [Thu, 1 Oct 2020 10:25:55 +0000 (12:25 +0200)]
ARM: dts: stm32: Add missing dm-spl props for SPI NOR on AV96
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tom Rini [Thu, 1 Oct 2020 18:51:58 +0000 (14:51 -0400)]
Revert "net: smc911x: Automatically Update ethaddr with MAC"
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
usb: xhci: convert to TRB_LEN() and TRB_INTR_TARGET()
For normal TRB fields:
use TRB_LEN(x) instead of ((x) & TRB_LEN_MASK);
and use TRB_INTR_TARGET(x) instead of
(((x) & TRB_INTR_TARGET_MASK) << TRB_INTR_TARGET_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
usb: xhci: add quirks flag to support MediaTek xHCI 0.96
There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
usb: xhci: create one unified function to calculate TRB TD remainder
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Porting from the Linux: c840d6ce772d("xhci: create one unified function to calculate TRB TD remainder.") 124c39371114("xhci: use boolean to indicate last trb in td remainder calculation")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from
rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument
always set to 1 during xfer which introduced read/write errors, whereas
earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to
1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0.
Fixes: 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Philippe Reynes [Fri, 18 Sep 2020 12:13:02 +0000 (14:13 +0200)]
sntp: use udp framework
This commits update the support of sntp to use
the framework udp. This change allows to remove
all the reference to sntp in the main network
file net/net.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philippe Reynes [Fri, 18 Sep 2020 12:13:00 +0000 (14:13 +0200)]
net: add a generic udp protocol
This commit adds a generic udp protocol framework in the
network loop. So protocol based on udp may be implemented
without modifying the network loop (for example custom
wait magic packet).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ley Foon Tan [Tue, 25 Aug 2020 02:26:36 +0000 (10:26 +0800)]
net: tftp: Fix store_block offset calculation
tftp_cur_block start with 1 for first block, but tftp_cur_block counter is
start with zero when block number is rollover. The existing code
"tftp_cur_block - 1" will cause the block number become -1 in store_block()
when tftp_cur_block is 0 when tftp_cur_block is rollover.
The fix pass in tftp_cur_block to store_block() and minus the
tftp_block_size when do the offset calculation.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Ley Foon Tan [Tue, 25 Aug 2020 02:26:35 +0000 (10:26 +0800)]
net: tftp: Fix tftp_prev_block counter update
Fixes missing update to tftp_prev_block counter before increase
tftp_cur_block counter when do the tftpput operation.
tftp_prev_block counter is used in update_block_number() function to
check whether block number (sequence number) is rollover. This bug
cause the tftpput command fail to upload a large file when block
number is greater than 16-bit (0xFFFF).
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
net: ftgmac100: Add support for board specific PHY interface address
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com> Reviewed-by: Cédric Le Goater <clg@kaod.org>
Heiko Stuebner [Tue, 9 Jun 2020 13:37:40 +0000 (15:37 +0200)]
net: phy: mscc: sync rx/tx delay settings with Linux on vsc85xx
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot.git / log