Marek Vasut [Fri, 24 Aug 2018 19:43:17 +0000 (21:43 +0200)]
sh: tmu: Clean up register usage
The code uses all in all three TMU registers, drop the massive
register layout structures and just define the required timer
registers and use them throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Fri, 24 Aug 2018 19:34:07 +0000 (21:34 +0200)]
sh: tmu: Clean up CONFIG_SH_TMU_CLK_FREQ
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Fri, 24 Aug 2018 19:23:04 +0000 (21:23 +0200)]
sh: tmu: Inline tmu_timer_{start,stop}()
These functions are always called for timer = 0, so drop the
timer check. Since these functions are called from one place
only and they are reduced to one line of code, just inline
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adam Ford [Mon, 3 Sep 2018 08:47:52 +0000 (03:47 -0500)]
MMC: davinici_mmc: Enable CD and WP with DM and OF_CONTROL
When used with a device tree, this will extract the card detect
and write protect pins from the device tree and configure them
accordingly. This assumes the GPIO_ACTIVE_LOW/HIGH is supported
by da8xx_gpio.
Adam Ford [Sun, 19 Aug 2018 16:11:03 +0000 (11:11 -0500)]
ARM: am3517_evm: Disable DM_I2C_COMPAT
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
Adam Ford [Mon, 3 Sep 2018 19:05:41 +0000 (14:05 -0500)]
ARM: omap3_logic: Enable DM_PMIC and DM_REGULATOR
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Adam Ford [Thu, 9 Aug 2018 11:15:12 +0000 (06:15 -0500)]
MMC: Enable DM_MMC for Davinci
With CONFIG_BLK becoming a requirement, the Davinci MMC driver
needs to be updated with DM_MMC support. Since SPL is tiny and
many boards do not support DM in SPL, this retains the backwards
compatibility for those boards who need to initialize MMC manually
in SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au> Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Mon, 3 Sep 2018 18:56:47 +0000 (13:56 -0500)]
ARM: omap3_logic: Enable Pinctrl
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Adam Ford [Tue, 21 Aug 2018 12:16:56 +0000 (07:16 -0500)]
mmc: omap_hsmmc: Make DM_GPIO calls dependent on DM_GPIO
The getcd and getwp functions when DM_MMC is enabled are
assumming the DM_GPIO is enabled. In cases (like SPL) where
DM_GPIO may not be enabled, wrap these calls in an #ifdef
Adam Ford [Tue, 21 Aug 2018 01:43:00 +0000 (20:43 -0500)]
DM: serial: ti_omap3_common: Don't define serial unless !DM_SERIAL
The serial port was being manually configured during SPL build,
however in preparation to allow DM in SPL, this needs to change
to be based on whether or not DM_SERIAL is enabled because, soon
the assumption that SPL means no DM may not be accurate.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Tue, 21 Aug 2018 01:34:00 +0000 (20:34 -0500)]
ARM: mach-omap2: Don't initialize I2C if DM_I2C is enabled
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it. This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Tue, 21 Aug 2018 01:27:48 +0000 (20:27 -0500)]
DM: omap_gpio: Reduce overhead when used with OF_PLATDATA
Platforms with limited resources in SPL may enable OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Tue, 21 Aug 2018 01:24:35 +0000 (20:24 -0500)]
DM: OMAP24XX_I2C: Reduce overhead when used with OF_PLATDATA
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Adam Ford [Tue, 21 Aug 2018 01:24:34 +0000 (20:24 -0500)]
DM: I2C: Reduce overhead when used with OF_PLATDATA
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Adam Ford [Fri, 17 Aug 2018 04:13:34 +0000 (23:13 -0500)]
DM: GPIO: Fix da8xx GPIO indexing over GPIO 32
The GPIO banks are broken up into two 16-bit registers for each
bank set. Unfortunately, the math that determines how to shift
blindly shifted by the number of the gpio. This worked for gpio
numbers under 32, but higher gpio's are broken. This fixes the
gpio index, so the bank is passed and the shift amount within
the register is passed now instead of the gpio number.
Fixes: 8e51c0f25406("dm: gpio: Add DM compatibility to
GPIO driver for Davinci")
Adam Ford [Wed, 15 Aug 2018 18:22:03 +0000 (13:22 -0500)]
ARM: configs: Add da850evm_nand to boot from NAND
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
include: am654_evm: Establish initial environment for SD card boot
Create a basic U-Boot environment that allows the automatic loading
of a Linux Kernel located at /boot/Image and an associated device tree
blob located at /boot/k3-am654-base-board.dtb from the secondary
partition of an ext4-formatted SD card on the AM654x EVM. Furthermore
the boot.scr and uEnv.txt detection and loading schemes are supported
in a manner already known from other TI platforms.
Note that this is intended to be a starting point to enable initial
board use and will most certainly get extended and refactored as
different boot media become available.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:51 +0000 (15:57 +0530)]
remoteproc: Introduce K3 system controller
K3 specific SoCs have a dedicated microcontroller for doing
resource management. Any HLOS/firmware on compute clusters should
load a firmware to this microcontroller before accessing any resource.
Adding support for loading this firmware.
After the K3 system controller got loaded with firmware and started
up it sends out a boot notification message through the secure proxy
facility using the TI SCI protocol. Intercept and receive this message
through the rproc start operation which will need to get invoked
explicitly after the firmware got loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:50 +0000 (15:57 +0530)]
remoteproc: Allow for individual remoteproc initialization
Existing rproc_init() api tries to initialize all available
remoteproc devices. This will fail when there is dependency
among available remoteprocs. So introduce a separate api
that allows to initialize remoteprocs individually based
on id.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:47 +0000 (15:57 +0530)]
mailbox: Allow attaching private data for mbox_chan
Sometimes mbox controllers wants to store private data in
mbox_chan so that it can be used at a later point of time.
Adding support for hooking private data.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
sysreset: Add TI System Control Interface (TI SCI) sysreset driver
Devices from the TI K3 family of SoCs like the AM654x contain a Device
Management and Security Controller (SYSFW) that manages the low-level
device control (like clocks, resets etc) for the various hardware
modules present on the SoC. These device control operations are provided
to the host processor OS through a communication protocol called the TI
System Control Interface (TI SCI) protocol.
This patch adds a system reset driver that communicates to the system
controller over the TI SCI protocol for allowing to perform a system-
wide SoC reset.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
power domain: Introduce TI System Control Interface (TI SCI) power domain driver
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:44 +0000 (15:57 +0530)]
power domain: Add support for multiple powerdomains per device
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
clk: Introduce TI System Control Interface (TI SCI) clock driver
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
clk: Extend clock control with an optional data field
Some systems require more than a single ID to identify and configure any
clock provider. For those scenarios add an optional data field to the
clock control structure.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
reset: Introduce TI System Control Interface (TI SCI) reset driver
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management of
various devices present on the SoC. Various reset functionalities are
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/reset/reset-ti-sci.c driver of
the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
reset: Extend reset control with an optional data field
Some systems require more than a single ID to identify and configure any
reset provider. For those scenarios add an optional data field to the
reset control structure.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To support scenarios where a firmware device node has subnodes that
have their own drivers automatically scan the DT and bind those when
the firmware device gets bound.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:37 +0000 (15:57 +0530)]
firmware: ti_sci: Add support for processor control services
TI-SCI message protocol provides support for controlling of various
physical cores available in SoC. In order to control which host is
capable of controlling a physical processor core, there is a processor
access control list that needs to be populated as part of the board
configuration data.
Introduce support for the set of TI-SCI message protocol apis that
provide us with this capability of controlling physical cores.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:35 +0000 (15:57 +0530)]
firmware: ti_sci: Add support for clock control
In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Introduce the fundamental
device management capability support to the driver protocol
as part of this change.
firmware: ti_sci: Add support for board configuration
TI-SCI message protocol provides support for board configuration
to assign resources and other board related operations.
Introduce the board configuration capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:32 +0000 (15:57 +0530)]
firmware: Add basic support for TI System Control Interface (TI SCI) protocol
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:14 +0000 (15:57 +0530)]
armv8: K3: am654: Introduce FIT generator script
Add a script that is capable of generating a FIT image
source file that combines ATF, SPL(64 bit) and DT.
This combined image is used by R5 SPL and start ATF
on ARMv8 core.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:11 +0000 (15:57 +0530)]
arm: K3: am654: Add support for boot device detection
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:10 +0000 (15:57 +0530)]
arm: K3: Update _start instruction
On K3 family SoCs, once the ROM loads image on R5, M3 resets R5 and
expects to start executing from 0x0. In order to handle this ROM
updates the boot vector of R5 such that first 64 bytes of image load
address are mapped to 0x0.
In this case, it is SPL's responsibility to jump to the proper image
location. So, update the PC with address of reset vector(like how
other exception vectors are handled), instead of branching to reset.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 27 Aug 2018 10:27:09 +0000 (15:57 +0530)]
arm: K3: Add support for AM654 SoC definition
The AM654 device is designed for industrial automation and PLC
controller class platforms among other applications. Introduce
base support for AM654 SoC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN again
With the migration to distro-boot, the size of the U-Boot proper
image for uniphier_v7_defconfig exceeded the current limit, 576KB.
Increase it to 832KB.
CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image
over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads
the SPL to the physical address 0x100000.
Michal Simek [Thu, 26 Jul 2018 13:33:51 +0000 (15:33 +0200)]
cmd: fpga: Add support for missing fpga loadmk commands
There are ways how to call fpga loadmk
1. Full command
fpga loadmk [dev] [address]
2. Dev setup via variable
set fpga [dev]
fpga loadmk [address]
3. Address setup via variable
set fpgadata [address]
fpga loadmk [dev]
4. Dev and address setup via variables
set fpga [dev]
set fpgadata [address]
fpga loadmk
Before this patch only cases 1 and 3 are working but the part of code
was trying to support also cases 2 and 4.
This patch is adding support for cases 2 and 4 to have all of
combinations supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 4 Jun 2018 12:57:34 +0000 (14:57 +0200)]
cmd: fpga: Extract fpga info command to separate function
Move fpga info to U_BOOT_CMD_MKENT subcommand.
Also use strtol instead of simple_strtoul. The reason is that if -1 is
passed (or fpga info without "fpga" variable) the list of all fpgas is
shown.
This functionality is in the fpga core but it couldn't be performed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 30 May 2018 09:28:57 +0000 (11:28 +0200)]
cmd: fpga: Clean wrong_parms handling
There is no reason to check parameters in separate switch. Check them
directly when they are read. Also there is no reason to check loadmk
case separately because fpga_data address must be non zero too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 4 Jun 2018 11:57:19 +0000 (13:57 +0200)]
cmd: fpga: Remove parameter checking from fpga loadfs command
Parameter checking is dead code because all the time there must be all
params assigned. If they are not assigned there is no 9th parameters
passed and checking before return CMD_RET_USAGE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 30 May 2018 09:18:38 +0000 (11:18 +0200)]
cmd: fpga: Move parameter checking for loadfs/loads
There is no reason to check parameters in separate switch before main
one. This patch is simplifying error path and checking parameters right
after assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log