For the correct power cycle sequence with stm32_sdmmc2, the write of the
power cycle value in PWRCTL field of SDMMC_POWER register is now done in
stm32_sdmmc2_host_power_cycle() and no more in stm32_sdmmc2_pwrcycle().
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.
In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.
The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().
The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.
spl: dm_mmc: Initialize only the required mmc device
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
Tom Rini [Tue, 8 Oct 2019 22:43:56 +0000 (18:43 -0400)]
Merge tag 'u-boot-atmel-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2020.01 cycle
The feature set includes support for two new boards from Microchip AT91:
The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2
SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which
is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor,
QSPI, etc
The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the
SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio,
Camera sensor connector, etc.
The full support for sam9x60ek will come at a later time. There are
still missing bits regarding the clock support and power management
controller.
Tom Rini [Tue, 8 Oct 2019 22:37:19 +0000 (18:37 -0400)]
Merge branch '2019-10-08-master-imports'
- Python3 conversion of genboardscfg.py
- Resync Kconfiglib.py
- Switch to running CI on Ubuntu "bionic" to facilitate Python 3.6 being
the minimum we use and test.
Tom Rini [Fri, 4 Oct 2019 16:12:54 +0000 (12:12 -0400)]
gitlab-ci: Switch to Ubuntu 18.04 image
In order to run all filesystem tests we need to have newer ext4 tools,
move up to Ubuntu 18.04 'bionic' for our base. We need to change
slightly how we invoke the provided grub-mkimage. This will also make
future python3 work easier.
Tom Rini [Fri, 4 Oct 2019 16:12:53 +0000 (12:12 -0400)]
gitlab-ci: Have buildman use /tmp for output
When running as another user we might not be able to use '..' for
certain directories and this is the default for buildman. Specify an
output directory instead.
Tom Rini [Mon, 7 Oct 2019 21:17:36 +0000 (17:17 -0400)]
buildman: Perform tests in a temporary directory
We may not always be able to write to the default output directory so
have a temporary directory for our output be created.
Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Stephen Warren <swarren@wwwdotorg.org> Suggested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Adam Ford [Tue, 8 Oct 2019 13:01:12 +0000 (08:01 -0500)]
ARM: imx6q_logic: Fix MMC2 booting
With the reverting of a previous change to spl_boot_device,
this board needs a new solution to determining if we're booting
from MMC1 or MMC2.
This patch creates board_boot_order function which overrides the
standard, and returns not only MMC1, or MMC2, but also can fall
back to NAND or the serial downloader should other boot options
fail.
imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Igor Opaniuk [Wed, 24 Jul 2019 15:09:57 +0000 (18:09 +0300)]
pinctrl: nxp: DM_FLAG_PRE_RELOC by default
For NXP SoCs we have to set pinmux configuration ASAP (ideally
before relocation) to get serial console working. Without this we miss
almost the half of output (U-boot version, CPU defails, Reset cause,
DRAM details etc.).
To achieve this we need to force appropriate pinctrl drivers to get
probed before relocation.
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Saravanan Sekar [Sun, 4 Aug 2019 17:36:42 +0000 (19:36 +0200)]
imx: variscite: Fix regression of SPL and U-boot booting
1. Commit 3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.
As explained by Lukas Auer:
"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x4000) leaves U-Boot with not enough memory to
do this, causing it to hang."
Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.
2. CONFIG_SPL_TEXT_BASE was moved to Kconfig, so added in defconfig
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133eef2e068f9c33853b6584d7fcbfa9d2e)
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 7 Aug 2019 17:05:59 +0000 (12:05 -0500)]
ARM: imx6q_logic: Enable DM_SERIAL
In order to call preloader_console_init from board_init_f when
DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access
to DM and device tree.
This patch calls spl_early_init just before preloader_console_init()
and enables DM_SERIAL and SPL_DM_SERIAL.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Wed, 7 Aug 2019 17:05:58 +0000 (12:05 -0500)]
ARM: imx6qlogic: Cleanup board_init_f
Per the workflow found in crt0.S, we don't need to clear BSS in
board_init_f nor do we need to call board_init_r since that will be
done for us from main when we return from board_init_f.
This patch removes the unneeded function calls from board_init_f.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jacky Bai [Thu, 8 Aug 2019 09:59:11 +0000 (09:59 +0000)]
ddr: imx8m: Fix the ddr init hang on imx8mq
On, i.MX8MQ, the PLL config must be done when ddrmix
isolation is released. So move the dram pll init after
iso config done. For other i.MX8M SOC, either init pll
before or after isolation is ok.
Signed-off-by: Jacky Bai <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Bai Ping [Thu, 8 Aug 2019 09:59:05 +0000 (09:59 +0000)]
imx8mq: Update the ddrc QoS setting for B1 chip
Update the ddrc Qos setting for B1 to align with B0's setting.
Correct the initial clock for dram_pll. This setting will be
overwrite before ddr phy training. Although there is no impact
on the dram init, we still need to correct it to eliminate
confusion.
Signed-off-by: Bai Ping <ping.bai@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Tested-by: Robby Cai <robby.cai@nxp.com>
Ye Li [Wed, 14 Aug 2019 11:31:31 +0000 (11:31 +0000)]
spi: fsl_qspi: Update write data size for page program LUT
The write data size can be overwritten by writing to the IDATSZ
field of IPCR register. Since the driver always updates the IDATSZ
in page program operation. Set the LUT data size to 0 to align
the codes with iMX.
Ye Li [Wed, 14 Aug 2019 11:31:27 +0000 (11:31 +0000)]
spi: fsl_qspi: Fix DDR mode setting for latest iMX platforms
On latest iMX platforms like iMX7D/iMX6UL/iMX8MQ, the QSPI controller
is updated to have TDH field in FLSHCR register. According to reference
manual, this TDH must be set to 1 when DDR_EN is set. Otherwise, the TX
DDR delay logic won't be enabled.
Another issue in DDR mode is the MCR register will be overwritten in
every read/write/erase operation. This causes DDR_EN been cleared while
TDH=1, then no clk2x output for TX data shift and all operations will
fail.
Peng Fan [Mon, 23 Sep 2019 02:18:48 +0000 (10:18 +0800)]
spl: nor: support loading i.MX container format file
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marex@denx.de> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 23 Sep 2019 02:18:47 +0000 (10:18 +0800)]
spl: spi: support loading i.MX container format file
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marex@denx.de> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 23 Sep 2019 02:18:46 +0000 (10:18 +0800)]
spl: nand: support loading i.MX container format file
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marex@denx.de> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 23 Sep 2019 02:18:44 +0000 (10:18 +0800)]
imx8: Add support to get container image set size
To avoid hardcoded offset when adding u-boot.cnt to flash.bin, we use
flexible offset which is calculated based on the size of the container
image generated int the first stage. And pad u-boot.cnt at 1KB
alignment.
So add code to get the offset when SPL loading u-boot.cnt.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 23 Sep 2019 02:18:43 +0000 (10:18 +0800)]
spl: nand: Introduce spl_nand_get_uboot_raw_page
Introduce weak spl_nand_get_uboot_raw_page, then platform could
have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: Marek Vasut <marex@denx.de> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Michal Simek <michal.simek@xilinx.com>
Peng Fan [Mon, 23 Sep 2019 02:18:42 +0000 (10:18 +0800)]
spl: nor: introduce spl_nor_get_uboot_base
Introduce weak spl_nor_get_uboot_base, then platform have their own
implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: Marek Vasut <marex@denx.de> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Michal Simek <michal.simek@xilinx.com>
Peng Fan [Mon, 23 Sep 2019 02:18:41 +0000 (10:18 +0800)]
spl: spi: introduce spl_spi_get_uboot_offs
Introduce a weak function spl_spi_get_uboot_offs, then
platform could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: Marek Vasut <marex@denx.de> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Michal Simek <michal.simek@xilinx.com>
Peng Fan [Mon, 23 Sep 2019 02:18:40 +0000 (10:18 +0800)]
spl: mmc: introduce spl_mmc_get_uboot_raw_sector
Introduce a weak function spl_mmc_get_uboot_raw_sector, then platform
could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: Marek Vasut <marex@denx.de> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Michal Simek <michal.simek@xilinx.com>
Peng Fan [Tue, 27 Aug 2019 06:26:04 +0000 (06:26 +0000)]
arm: dts: add i.MX8MM pin func
Import i.MX8MM pin func from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Peng Fan [Tue, 27 Aug 2019 06:26:01 +0000 (06:26 +0000)]
arm: dts: import i.MX8MM dtsi
Import i.MX8MM dtsi from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Peng Fan [Tue, 27 Aug 2019 06:25:51 +0000 (06:25 +0000)]
imx8m: add clk support for i.MX8MM
Introduce clk implementation for i.MX8MM, including pll configuration,
ccm configuration. Mostly will be done clk dm driver,
but such as DRAM part, we still use non clk dm driver, because we
have limited sram.
Ye Li [Tue, 27 Aug 2019 06:25:34 +0000 (06:25 +0000)]
imx8m: Configure trustzone region 0 for non-secure access
Set trustzone region 0 to allow both non-secure and secure access
when trust zone is enabled. We found USB controller fails to access
DDR if the default region 0 is secure access only.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 27 Aug 2019 06:25:27 +0000 (06:25 +0000)]
imx8m: Fix MMU table issue for OPTEE memory
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE
memory from its settings. So ARM speculative prefetch in u-boot may access
that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory
is set to secure access, then the speculative prefetch will fail and cause
various memory issue in u-boot.
The fail address register and int_status register in trustzone has logged
that speculative access from u-boot.
Peng Fan [Tue, 27 Aug 2019 06:24:47 +0000 (06:24 +0000)]
ddr: imx8m: fix ddr firmware location when enable SPL OF
With CONFIG_SPL_OF_CONTROL, the device tree will be padded to
end of the u-boot-spl-nodtb.bin, however we also put
the ddr firmware file to this location, so need to adapt
the code with SPL OF and align to 4 bytes to ease copy firmware.
Peng Fan [Tue, 27 Aug 2019 06:24:43 +0000 (06:24 +0000)]
tools: imx8m_image: align spl bin image size
The loader for the DDR firmware in drivers/ddr/imx/imx8m/helper.c uses a
4-byte-aligned address to load the firmware. In cases where OF is
enabled in SPL the dtb will be appended to the SPL binary and can result
in a binary that is not aligned correctly. If OF is not enabled in SPL,
`_end` is already aligned correctly, but this patch does not hurt.
To ensure the correct alignment we use dd to create a temporary file
u-boot-spl-pad.bin with the correct padding.
Since recent splash changes common code for splashscreen logo
should be used instead of adding duplicated code under board
directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations
used old board specific logo code and do not link, fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets") Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Breno Lima <breno.lima@nxp.com>
Patrick Wildt [Thu, 3 Oct 2019 14:08:35 +0000 (16:08 +0200)]
imx: add support for i.MX7/i.MX8MQ reset controller
Add support for the reset controller that's used on the i.MX7D
and i.MX8MQ. This will be needed to be able to assert the PCIe
reset pins. Bindings taken from Linux, driver implementation
mostly taken from Linux and adjusted to U-Boot infrastructure.
Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Patrick Wildt [Thu, 3 Oct 2019 13:51:50 +0000 (15:51 +0200)]
imx: add support for i.MX8MQ power domain controller
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
mmc: Replace printf with debug call for timeouts in the i.MX28 mxs driver
This change replaces printf() with debug() for the notification about
commands timeouts.
This is done on purpose (also other drivers use such approach - dw_mmc.c,
mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one
is using sd card or eMMC device.
In such situation timeout is a some kind of a "normal" behavior and there
shall not be any output to the console.
There is no impact on boot time for boards using this driver (even in SPL)
when two extra timeouts are returned (no SD card present, only eMMC
available).
Boot time tested with grabserial:
sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*"
spi: fix: Call mxs_reset_block() during DM/DTS probe
Without this change the DM/DTS version of mxs_spi driver doesn't reset the
SPI IP block in probe.
As a result this driver (when used solely on U-Boot proper) relies on reset
performed by mxs spi driver in SPL.
In the use case where eMMC is used in SPL as a boot primary device, the
mxs_reset_block() is not called at all and DM/DTS aware SPI driver in
U-Boot proper is malfunctioning.
dts: imx28: Remove #include "imx28.dtsi" from imx28-u-boot.dtsi file
After this change it is possible to use imx28-<board>-u-boot.dtsi with
the imx28-u-boot.dtsi explicitly included without breaking setup from
imx28-<board>.dts file.
The problem is that the imx28.dtsi included in a wrong place overrides the
changes made in imx28-<board>.dts. As a result some devices are "disabled"
in the final DTB.
projects / u-boot.git / log