Stefan Roese [Fri, 10 May 2019 11:34:05 +0000 (13:34 +0200)]
arm: mvebu: armada-370-xp.dtsi: Add "u-boot, dm-pre-reloc" to "internal-regs"
Without this U-Boot specific property, booting on Armada XP theadorable
fails in SPL. All nodes in the "internal-regs" (simple-bus) DT node are
not scanned, so the UART node is missing (and others).
I'm not adding this property in an *u-boot.dtsi file, since there is
none matching the generic rules for all files including this dtsi
file. So to not miss any of the boards using this dtsi file, I'm
adding it to this file directly, which makes the Linux merge a less
easy unforunately.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Cc: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tom Rini [Sun, 19 May 2019 20:46:24 +0000 (16:46 -0400)]
Merge tag 'efi-2019-07-rc3-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc3 (2)
Minor patches to improve UEFI specification compliance are provided.
To allow running the UEFI self compliance tests an outdated version of
the Unicode collation protocol has been added as a configuration option
(disabled by default).
Tom Rini [Sun, 19 May 2019 13:36:48 +0000 (09:36 -0400)]
Merge branch '2019-05-19-master-imports'
- Convert SYS_[DI]CACHE_OFF to Kconfig, introduce SPL variant.
- Various bcm96* fixes.
- Import include/android_bootloader_message.h from AOSP
- Assorted other small fixes.
x86: coreboot: make it possible to process unhandled tags
coreboot makes it possible to add own entries into coreboot's
table at a per mainboard basis. As there might be some custom
ones it makes sense to provide a way to process them.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
efi_loader: check device path in InstallMultipleProtocolInterfaces
According to the UEFI spec InstallMultipleProtocolInterfaces() must check
if a device path has already been installed. In this case it must return
EFI_ALREADY_STARTED.
Cf. UEFI SCT II 2.6 A (2017),
3.3.16 InstallMultipleProtocolInterfaces(), 5.1.3.16.1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In EFI 1.10 a version of the Unicode collation protocol using ISO 639-2
language codes existed. This protocol is not part of the UEFI specification
any longer. Unfortunately it is required to run the UEFI Self Certification
Test (SCT) II, version 2.6, 2017. So we implement it here for the sole
purpose of running the SCT. It can be removed once a compliant SCT is
available.
The configuration option defaults to no.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Most of Rob's original patch is already merged. Only the deprecated
protocol is missing. Rebase it and make it configurable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ibai Erkiaga [Wed, 15 May 2019 21:10:04 +0000 (22:10 +0100)]
Kconfig: fix FIT offset prompt text
The current prompt text for FIT external offset is identical to
SYS_TEXT_BASE which might confuse the users. Provided more accurate
description for the prompt text.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Reviewed-by: Marek Vasut <marex@denx.de>
Alex Deymo [Tue, 14 May 2019 19:05:26 +0000 (21:05 +0200)]
Import include/android_bootloader_message.h from AOSP
This takes the latest changes from AOSP from the file
bootloader_message/include/bootloader_message/bootloader_message.h
in the repository
https://android.googlesource.com/platform/bootable/recovery
and re-licensed them to BSD-3 for U-Boot.
Minimum local changes have been applied (convert C++ to C comments and
adding #ifndef __UBOOT__ block to skip all the function declarations).
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Luca Boccassi [Tue, 14 May 2019 18:35:02 +0000 (19:35 +0100)]
tools: use read-only mmap in fit_check_sign
Add an option to open files in read-only mode in mmap_fdt so
that fit_check_sign can be used to inspect files on read-only
filesystems.
For example, this is useful when a key is shipped in a read-only
rootfs or squashfs.
Marek Vasut [Tue, 7 May 2019 19:17:02 +0000 (21:17 +0200)]
spl: Set spl_image->fdt_addr pointer for full fitImage configuration
Set the spl_image->fdt_addr pointer both for simple fitImage configuration
as well as full fitImage configuration, to let spl_perform_fixups() access
the DT and perform modifications to it if necessary.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
This board define the flag CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
but it's a mistake. It's a workaround for an issue in nand core.
This issue was fixed by the commit 5f626e78491c ("mtd: nand: raw:
Fix CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT behavior"). Now, this flag
break the nand on this board, so we simply remove it.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This board define the flag CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
but it's a mistake. It's a workaround for an issue in nand core.
This issue was fixed by the commit 5f626e78491c ("mtd: nand: raw:
Fix CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT behavior"). Now, this flag
break the nand on this board, so we simply remove it.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This board define the flag CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
but it's a mistake. It's a workaround for an issue in nand core.
This issue was fixed by the commit 5f626e78491c ("mtd: nand: raw:
Fix CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT behavior"). Now, this flag
break the nand on this board, so we simply remove it.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 3 May 2019 17:43:08 +0000 (19:43 +0200)]
dt: bcm63158: watchdog should use a 50Mhz clock
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Stefan Roese <sr@denx.de>
Philippe Reynes [Fri, 3 May 2019 17:43:07 +0000 (19:43 +0200)]
dt: bcm6858: watchdog should use a 50Mhz clock
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Stefan Roese <sr@denx.de>
Philippe Reynes [Fri, 3 May 2019 17:43:06 +0000 (19:43 +0200)]
watchdog: bcm6345: callback start use tick instead of ms
The function bcm6345_wdt_start use the argument timeout
as tick but it should be used as milliseconds.
A clock is added as requirement for this driver.
The frequency of the clock is then used to convert the
millisecond to ticks in the function bcm6345_wdt_start.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Stefan Roese <sr@denx.de>
Michal Simek [Mon, 25 Mar 2019 14:55:16 +0000 (15:55 +0100)]
Makefile: Prioritize external dtb if defined
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Trevor Woerner [Fri, 3 May 2019 13:41:00 +0000 (09:41 -0400)]
CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware] Signed-off-by: Tom Rini <trini@konsulko.com>
Trevor Woerner [Fri, 3 May 2019 13:40:59 +0000 (09:40 -0400)]
CONFIG_SYS_[DI]CACHE_OFF: convert to Kconfig
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com> Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards] Signed-off-by: Tom Rini <trini@konsulko.com>
Trevor Woerner [Fri, 3 May 2019 13:40:58 +0000 (09:40 -0400)]
CONFIG_SYS_[DI]CACHE_OFF: remove commented lines
Eventually these configuration items will be converted to Kconfig,
therefore there's little point in leaving commented-out versions of
them in include/configs.
Trevor Woerner [Fri, 3 May 2019 13:40:56 +0000 (09:40 -0400)]
CONFIG_SYS_[ID]CACHE_OFF: unify the 'any' case
According to De Morgan's Law[1]:
!(A && B) = !A || !B
!(A || B) = !A && !B
There are 5 places in the code where we find:
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
and 4 places in the code where we find:
#if (!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF))
In words, the construct:
!defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE on?"
and the construct:
defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE off?"
Therefore
!(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
means:
"the opposite of 'are they both off?'"
in other words:
"are either or both on?"
and:
(!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF)
means:
"are either or both on?"
As a result, I've converted the 4 instances of '(!A || !B)' to '!(A && B)' for
consistency.
Trent Piepho [Wed, 8 May 2019 23:30:06 +0000 (23:30 +0000)]
i2c: mxc: Hide kconfig based control in DM_I2C mode
These options only apply when not using DM_I2C. When using device
trees, the dt will enable and control the speeds of the I2C
controller(s) and these configuration options have no effect.
So disable them in DM_I2C mode. Otherwise they show up as decoys, and
make it look like one is enabling I2C controllers and setting the speed
when really it's doing nothing.
However, a system using a SPL build will not use DM_I2C in the SPL, even
if DM_I2C is enabled for the main u-boot. And so the SPL might use the
kconfig based I2C speed controls while the main u-boot does not.
Trent Piepho [Wed, 8 May 2019 23:30:01 +0000 (23:30 +0000)]
wandboard: Don't use I2C speed Kconfig settings with DM_I2C
When using DM_I2C the speed value supplied to setup_i2c() is not used,
so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to
compile, but did not actually use them.
Change this so we no longer need to define an unused macro to compile in
DM_I2C mode. Also make it more clear that they do not control the bus
speed. Otherwise it is quite easy to mistakenly believe they are used
to set the bus speed.
i2c: mxc_i2c: Fix read and read->write xfers in DM mode
This is an old driver that supports both device mapped and non-mapped
mode, and covers a wide range of hardware. It's hard to change without
risking breaking something. I have to tried to be exceedingly detailed
in this patch, so please excuse the length of the commit essay that
follows.
In device mapped mode the I2C xfer function does not handle plain read,
and some other, transfers correctly.
What it can't handle are transactions that:
Start with a read, or,
Have a write followed by a read, or,
Have more than one read in a row.
The common I2C/SMBUS read register and write register transactions
always start with a write, followed by a write or a read, and then end.
These work, so the bug is not apparent for most I2C slaves that only use
these common xfer forms.
The existing xfer loop initializes by sending the chip address in write
mode after it deals with bus arbitration and master setup. When
processing each message, if the next message will be a read, it sends a
repeated start followed by the chip address in read mode after the
current message.
Obviously, this does not work if the first message is a read, as the
chip is always addressed in write mode initially by i2c_init_transfer().
A write following a read does not work because the repeated start is
only sent when the next message is a read. There is no logic to send it
when the current message is a read and next is write. It should be sent
every time the bus changes direction.
The ability to use a plain read was added to this driver in
commit 2feec4eafd40 ("imx: mxc_i2c: tweak the i2c transfer method"),
but this applied only the non-DM code path.
This patch fixes the DM code path. The xfer function will call
i2c_init_transfer() with an alen of -1 to avoid sending the chip
address. The same way the non-DM code achieves this. The xfer
function's message loop will send the address and mode before each
message if the bus changes direction, and on the first message.
When reading data, the master hardware is one byte ahead of what we
receive. I.e., reading a byte from the data register returns a byte
*already received* by the master, and causes the master to start the RX
of the *next* byte. Therefor, before we read the final byte of a
message, we must tell the master what to do next. I add a "last" flag
to i2c_read_data() to tell it if the message is to be followed by a stop
or a repeated start. When last == true it acts exactly as before.
The non-DM code can only create an xfer where the read, if any, is the
final message of the xfer. And so the only callsite of i2c_read_data()
in the non-DM code has the "last" parameter as true. Therefore, this
change has no effect on the non-DM code. As all other changes are in
the DM xfer function, which is not even compiled in non-DM code, I am
confident that this patch has no effect on boards not using I2C_DM.
This greatly reduces the range of hardware that could be affected.
For DM boards, I have verified every transaction the "i2c" command can
create on a scope and they are all exactly as they are supposed to be.
I also tested write->read->write, which isn't possible with the i2c
command, and it works as well. I didn't fix multiple reads in a row, as
it's a lot more invasive and obviously no one has every wanted them
since they've never worked. It didn't seem like the extra complexity
was justified to support something no one uses.
It is not very clear how these work in relation to the exact I2C xfers
they produce. In paticular, the address length is somewhat overloaded
in the read method. Clearly document the existing behavior. Maybe this
will help the next person who needs to work on this driver and not break
non-DM boards.
configs: arndale: Use appropriate driver for Asix AX88760
Arndale board has an Asix AX88760 USB 2.0 Hub and Fast Ethernet combo.
The appropriate driver for it is USB_ETHER_ASIX.
The mistake probably came from misinterpretation of commit e9954b867ce0
("usb: eth: add ASIX AX88179 DRIVER") which was tested on RECS5250 COM
module. This module indeed has Exynos5250 and some similarities with
Arndale 5250 board but the USB/Ethernet chip used there is apparently
different.
Fixes: f58ad98a621c ("usb: net: migrate USB Ethernet adapters to Kconfig") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CONFIG_DM_I2C_COMPAT was introduced in
include/configs/exynos5-common.h in commit 189d80166b31 ("exynos5:
enable dm i2c") and then it propagated up to configs/arndale_defconfig.
However since beginning the Arndale board (Exynos5250) was not using
I2C.
In fact, the Arndale board is not configuring its PMIC (S5M8767) which
uses I2C bus. This setting can be thus safely removed to fix build
warning:
This board uses CONFIG_DM_I2C_COMPAT. Please remove
(possibly in a subsequent patch in your series)
before sending patches to the mailing list.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arm: exynos: arndale: Remove unused CONFIG_POWER and CONFIG_POWER_I2C
The CONFIG_POWER and CONFIG_POWER_I2C were introduced in
include/configs/exynos5-common.h in commit 19bd3aaa5991 ("exynos5: fix
build break by adding CONFIG_POWER") and then it propagated up to
include/configs/arndale.h. However before that commit, there was no
build break at all on Arndale and SMDK5250 boards. It seems the commit
fixed nothing and just added unused defines.
In fact, the Arndale board is not configuring its PMIC (S5M8767) which
uses I2C bus.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Rini [Wed, 15 May 2019 11:10:32 +0000 (07:10 -0400)]
Merge tag 'u-boot-stm32-mcu-20190514' of https://github.com/pchotard/u-boot
STM32 MCUs update:
_ Add MPU region for SPI NOR memory mapped region
_ Add missing QSPI flash compatible for STM32 F7 boards
_ Update spi-tx-bus-width and spi-rx-bus-width properties
_ Add QSPI support for STM32F469 Discovery board
This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
James Byrne [Wed, 6 Mar 2019 12:48:27 +0000 (12:48 +0000)]
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together
Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Wed, 6 Mar 2019 18:47:22 +0000 (19:47 +0100)]
ARM: dts: socfpga: Factor out U-Boot specifics from A10 handoff files
Pull out the u-boot,dm-pre-reloc from socfpga_arria10_socdk_sdmmc_handoff.dtsi
into separate dtsi header file to make it easier to patch in custom handoff
dtsi files, without having to manually add the U-Boot bits. Shuffle the include
clauses in the A10 DT files to make it obvious what gets included where without
having to follow confusing long chain of includes, i.e. board DT file includes
everything it needs.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
arm: socfpga: Re-add support for Aries MCV SoM and MCVEV[KP] board
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d568
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de> CC: Marek Vasut <marex@denx.de> CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The stratix 10 reset manager ad-hoc code in arch/arm contains an unused
function 'reset_deassert_peripherals_handoff' that has been added from
the beginning. As this is probably a result of copying the gen5 reset
manager and this function has never been used, remove it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
commit c5de2b7eae68 ("arm: socfpga: implement proper peripheral reset")
has removed the call to 'reset_deassert_peripherals_handoff()' from
socfpga gen5 SPL since the reset driver now handles resets. However,
commit c1d4b464c8b8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA")
has re-added this ad-hoc reset code, so that all peripherals were now
again enabled instead of letting the drivers enable them by request.
While at it, remove this function for gen5 as it should not be used.
Fixes: commit c1d4b464c8b8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Mon, 13 May 2019 11:13:28 +0000 (07:13 -0400)]
Merge tag 'efi-2019-07-rc3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc3
The development target for the UEFI sub-system is EBBR compliance. We have
already implemented some further protocols to enable running the UEFI Shell
and the UEFI SCT test suite.
As some boards are severely memory constrained make some of these extras
customizable.
Provide bug fixes. The most prominent ones let us pass the UEFI SCT memory
allocation tests.
In RestoreTPL() we trigger the notification function of queued events. If
we do not mark the event as non-queued before calling the notification
function, this results in an infinite recursive call sequence.
Mark the event as non-queued before entering the notification function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert 'cadence_spi_ofdata_to_platdata' to use dev_read_* functions to
read driver parameters and 'dev_read_first_subnode'/'ofnode_read_*' to
read flash (child node) parameters.
Tested on socfpga_socrates (socfpga gen5).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:32 +0000 (17:42 +0800)]
ARM: socfpga: Increase Malloc pool size to support FAT filesystem in SPL
Increasing Malloc pool size up to 0x15000 is required to support FAT in SPL
. The result of calculation is come from default max cluster(0x10000) +
others(0x2000) + additional memory for headroom(0x3000).
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:30 +0000 (17:42 +0800)]
spl: socfpga: Implement fpga bitstream loading with socfpga loadfs
Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:29 +0000 (17:42 +0800)]
ARM: socfpga: Add the configuration for FPGA SoCFPGA A10 SoCDK
Update the default configuration file to enable the necessary functionality
to get the SoCFPGA loadfs driver support. This would enable the
implementation of programming bitstream into FPGA from MMC.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
projects / u-boot.git / log