Stephen Warren [Thu, 21 Apr 2016 22:03:37 +0000 (16:03 -0600)]
ARM: tegra: import latest Jetson TK1 spreadsheet
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.
The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 20 Apr 2016 21:46:50 +0000 (15:46 -0600)]
pci: tegra: fix DM conversion issues on Tegra20
Tegra20's PCIe controller has a couple of quirks. There are workarounds in
the driver for these, but they don't work after the DM conversion:
1) The PCI_CLASS value is wrong in HW.
This is worked around in pci_tegra_read_config() by patching up the value
read from that register. Pre-DM, the PCIe core always read this via a
16-bit access to the 16-bit offset 0xa. With DM, 32-bit accesses are used,
so we need to check for offset 0x8 instead. Mask the offset value back to
32-bit alignment to make this work in all cases.
2) Accessing devices other than dev 1 causes a data abort.
Pre-DM, this was worked around in pci_skip_dev(), which the PCIe core code
called during enumeration while iterating over a bus. The DM PCIe core
doesn't use this function. Instead, enhance tegra_pcie_conf_address() to
validate the bdf being accessed, and refuse to access invalid devices.
Since pci_skip_dev() isn't used, delete it.
I've also validated that both these WARs are only needed for Tegra20, by
testing on Tegra30/Cardhu and Tegra124/Jetson TKx. So, compile them in
conditionally.
Fixes: e81ca88451cf ("dm: tegra: pci: Convert tegra boards to driver model for PCI") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 12 Apr 2016 17:17:39 +0000 (11:17 -0600)]
ARM: tegra: enable GPU node by compatible value
In current Linux kernel Tegra DT files, 64-bit addresses are represented
in unit addresses as a pair of comma-separated 32-bit values. Apparently
this is no longer the correct representation for simple busses, and the
unit address should be represented as a single 64-bit value. If this is
changed in the DTs, arm/arm/mach-tegra/board2.c:ft_system_setup() will no
longer be able to find and enable the GPU node, since it looks up the node
by name.
Fix that function to enable nodes based on their compatible value rather
than their node name. This will work no matter what the node name is, i.e
for DTs both before and after any rename operation.
Cc: Thierry Reding <treding@nvidia.com> Cc: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Wed, 13 Apr 2016 23:38:02 +0000 (16:38 -0700)]
net: increase maximum frame size to accomediate VLAN packets
Ethernet packages with IEEE 802.1Q VLAN support may be up to 1522
bytes long. Increase the default size used to allocate packet
storage by 4 bytes. While at it, let git care about history and
rewrite the comment to represent the situation today only.
Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Lev Iserovich [Thu, 7 Jan 2016 23:04:16 +0000 (18:04 -0500)]
fdt: fix setting MAC addresses for multiple interfaces
For multiple ethernet interfaces the FDT offset of '/aliases' will change as we
are adding MAC addresses to the FDT.
Therefore only the first interface ('ethernet0') will get properly updated in
the FDT, with the rest getting FDT errors when we try to set their MAC address.
Signed-off-by: Lev Iserovich <iserovil@deshawresearch.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Tue, 26 Apr 2016 01:02:35 +0000 (03:02 +0200)]
usb: dwc2: Init desc_before_addr
Initialize desc_before_addr, otherwise the USB core won't send the
first 64B Get Device Descriptor request in common/usb.c function
usb_setup_descriptor() . There are some USB devices which expect
this sequence and otherwise can misbehave.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Wed, 27 Apr 2016 12:58:49 +0000 (14:58 +0200)]
usb: dwc2: Make OC protection configurable
Introduce a new flag in the controller private data, which allows selectively
disabling the OC protection. Use the standard 'disable-over-current' OF prop
to set this flag. This OC protection must be disabled on EBV SoCrates rev 1.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@kernel.org>
Marek Vasut [Wed, 27 Apr 2016 12:55:57 +0000 (14:55 +0200)]
usb: dwc2: Pull Ext VBUS macro from dwc_otg_core_init()
Introduce a boolean flag in the dwc2 controller private data and set
it according to the macro (for now) instead of having this macro
directly in the dwc_otg_core_init(). This will let us configure the
flag from DT or such later on, if needed.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@kernel.org>
Move CONFIG_SPL_TEXT_BASE down to 0x40200000 and set CONFIG_SPL_MAX_SIZE
to (SRAM_SCRATCH_SPACE_ADDR - CONFIG_SPL_TEXT_BASE), so that it's clear
what the limit is.
This will also help some compilers to fit all the code into the allocated
space.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Commit 7a439cadcf3192eb012a2432ca34670b676c74d2 broke generation of SPL
loadable FIT images (CONFIG_SPL_LOAD_FIT).
Fix it by removing the unnecessary storage of expected image type. This was a
left over of the previous implementation. It is not longer necessary since the
mkimage -b switch always has one parameter.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Mario Six [Wed, 20 Apr 2016 08:44:52 +0000 (10:44 +0200)]
i2c/eeprom: Always define I2C_RXTX_LEN
I2C_RXTX_LEN from include/i2c.h is not defined if CONFIG_DM_I2C is
enabled. This leads to a compilation error on boards that enable both
CONFIG_CMD_EEPROM and CONFIG_DM_I2C.
To avoid this, we define I2C_RXTX_LEN in cmd/eeprom.c if it is not
already defined.
mx6ul_evk does not come with a eMMC populated, so we should not
define CONFIG_SUPPORT_EMMC_BOOT as it causes SPL to not be able
to boot some brands of SD cards, such as SanDisk microSD HC - 8GB:
U-Boot SPL 2016.05-rc1-28384-g108f841 (Apr 19 2016 - 11:19:11)
Trying to boot from MMC1
spl: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
When CONFIG_SUPPORT_EMMC_BOOT is defined spl_boot_mode() returns
MMCSD_MODE_EMMCBOOT, so remove this option to have a reliable boot
via SD card.
Michal Simek [Thu, 28 Apr 2016 07:08:18 +0000 (09:08 +0200)]
kbuild: Do not append dtb for OF_EMBED case
dtb is already included in binary that's why there is no need to replace
u-boot-spl.bin with u-boot-spl-dtb.bin. This is only needed for
OF_SEPARATE is enabled. Only copy -nodtb.bin version which is straight
output from objcopy -O binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ronald Zachariah [Thu, 28 Apr 2016 05:08:34 +0000 (07:08 +0200)]
fs: ext4: fix symlink read function
The function ext4fs_read_symlink was unable to handle a symlink
which had target name of exactly 60 characters.
Signed-off-by: Ronald Zachariah <rozachar@cisco.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 2 May 2016 14:52:51 +0000 (10:52 -0400)]
Revert "omap3: Use raw SPL by default for mmc1"
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot. Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.
ARM: uniphier: allow to use System Bus for ROM boot mode of PH1-LD20
The System Bus is not available by default on the ROM boot mode of
PH1-LD20. To use devices connected to the System Bus, such as the
Micro Support Card, it is necessary to set up pin-muxing and some
System Bus Controller register.
Martin Pietryka [Wed, 27 Apr 2016 19:39:16 +0000 (21:39 +0200)]
drivers/video/am335x-fb: Properly point framebuffer behind palette
The DMA was outputting the palette on the screen because the base
for the DMA was not after the palette. In addition to that, the ceiling was
also too high, this led that the output on the screen was shifted.
NOTE: According to the TRM, even in 16/24bit mode a palette is required
in the first 32 bytes of the framebuffer.
See also:
https://e2e.ti.com/support/arm/sitara_arm/f/791/p/234967/834483#834483
"In this mode, the LCDC will assume all information is data and thus you
need to ensure that the DMA points to the first pixel of data and not the
first entry in the frame buffer which is the beginning of the 512 byte
palette."
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Martin Pietryka [Wed, 27 Apr 2016 19:39:15 +0000 (21:39 +0200)]
drivers/video/am335x-fb: Add support for 16bpp format
To support 16bpp we just need to change the raster_ctrl register
accordingly. Also 32bpp mode should work as well, but was not tested.
According to the TRM the uppermost byte will be ignored when
LCD_TFT_24BPP_UNPACK is set.
The switch logic is based on the Linux kernel tilcdc driver:
drivers/gpu/drm/tilcdc/tilcdc_crtc.c: lines 407 through 419
(kernel was checked out at commit: bcc981e9ed8)
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tom Rini [Wed, 27 Apr 2016 22:44:32 +0000 (18:44 -0400)]
omap3: Reduce logic/overo SPL max image size
While the OMAP3 has 64KiB of SRAM, per the TRM the download area is only
from 0x40200000 to 0x4020F000 and exceeding that will cause failure to
boot. Further, we need to make sure that we don't run into
SRAM_SCRATCH_SPACE_ADDR as once SPL is running we will write values
there and would corrupt our running image.
Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
We are running with the caches disabled when mctl_mem_matches gets called,
but the cpu's write buffer is still there and can still get in the way,
add a memory barrier to fix this.
This avoids mctl_mem_matches always returning false in some cases, which
was resulting in:
Michal Simek [Tue, 26 Apr 2016 14:12:06 +0000 (16:12 +0200)]
ARM64: zynqmp: Cleanup config file after CMD move
The patch:
"configs: Re-sync almost all of cmd/Kconfig"
(sha1: 78d1e1d0a157c8b48ea19be6170b992745d30f38)
doesn't remove empty if-endif. This patch is fixing it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
ARM: OMAP5: Enable ABB configuration for MM voltage domain
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
ARM: OMAP5/DRA7: Get rid of control_std_fuse_opp_vdd_mpu_2
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
The error message "spl: mmc block read error" may come from two
different functions, so we should better annotate the function name
where the error comes from to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Peter Griffin [Wed, 20 Apr 2016 16:14:03 +0000 (17:14 +0100)]
ARM: hikey: Simplify README instructions.
This patch updates and simplifies the hikey README. The old
instructions were hard to follow, and convoluted.
This patch also updates the link to the mcuimage.bin which was outdated.
Using an outdated mcuimage.bin results in the additional a53 cores
not coming online when the kernel issues PSCI requests to
arm trusted firmware (ATF).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Peter Griffin [Wed, 20 Apr 2016 16:14:02 +0000 (17:14 +0100)]
ARM: hisilicon: hikey: Align memory node with upstream kernel
The memory node gets automatically generated by U-Boot
in arch_fixup_fdt(), before passing control to the kernel
using U-Boots representation of the dram banks.
However the upstream kernel uses the memory node to carve-out
regions of RAM for various purposes. To make this work without
changing arch_fixup_fdt() which will effect many platforms
we replicate the upstream memory node layout using the dram
banks.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Peter Griffin [Wed, 20 Apr 2016 16:13:59 +0000 (17:13 +0100)]
ARM: hisilicon: hikey: Enable OF_CONTROL for hikey board.
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Mon, 4 Apr 2016 17:03:52 +0000 (11:03 -0600)]
sf: fix timebase data type in _wait_ready()
get_timer() returns an unsigned 64-bit value, but is currently assigned to
a signed 32-bit variable. Due to sign extension and data truncation, this
causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and
incorrectly) fire for about 50% of all time values, based on whether bit
31 is set. In sandbox at least, this causes the test to pass or fail based
on system uptime, as opposed to time since the U-Boot binary was started.
Fixes: 4efad20a1751 ("sf: Update status reg check in spi_flash_cmd_wait_ready") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
According to common eMMC partition table for Android boot (see
PARTS_DEFAULT definition in include/configs/dra7xx_evm.h), "bootloader"
partition (where u-boot.img is stored) starts at 256 KiB. Which is equal
to 512 sectors (as 1 MMC sector size is 512 bytes).
This patch fixes CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR constant so that
it points to correct address of "bootloader" partition and SPL is able to
read, parse and run u-boot.img correctly.
This change was originally done as part of patch [1] in omapzoom u-boot.
Without this patch, SPL fails to parse U-Boot header with next error:
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
[trini: Don't make CMD_USB_MASS_STORAGE nor CMD_DFU depend on CMD_USB] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 22 Apr 2016 20:41:25 +0000 (16:41 -0400)]
configs: Re-sync almost all of cmd/Kconfig
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Stephen Warren [Fri, 22 Apr 2016 19:34:16 +0000 (13:34 -0600)]
dfu: ram: fix number base of RAM entity parameters
U-Boot typically interprets unprefixed numbers as base 16, and DFU RAM
entity parsing has historically done so. Reverse the change to default
to base 10, so that values in previously working command-lines aren't
mis-parsed, causing RAM corruption, crashes, hangs, etc.
Fixes: 6aeb877afef0 ("drivers: dfu: ram: fix a crash with dfu ram with invalid dfu_alt_info env") Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[Test HW: AM335x BBB]
Roger Quadros [Tue, 19 Apr 2016 12:20:39 +0000 (15:20 +0300)]
usb: s3c-otg: Fix short packet for request size > ep.maxpacket
Request size can be greater than ep.packet and still end in a
short packet. We need to tackle this case as end of transfer
(if short_not_ok is not set) as indicated in USB 2.0 Specification [1],
else we get stuck up on certain protocols like fastboot.
[1] - USB2.0 Specification, Section 5.3.2 Pipes
Reported-by: Steve Rae <steve.rae@broadcom.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Steve Rae <steve.rae@broadcom.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Roger Quadros [Tue, 12 Apr 2016 12:51:48 +0000 (15:51 +0300)]
fastboot: Fix wMaxPacketSize for High-Speed IN endpoint
wMaxPacketSize for IN endpoing in High-Speed must be 512 and not 64.
While fixing that we do some clean ups like
- use cpu_to_le16(decimal_length) instead of hexadecimal length.
- No need to initialize bInterval to 0. Static variables are 0 initialized.
- Move descriptor setting from fastboot_add to to fastboot_bind.
- check for dual speed configuration before setting the high speed descriptors.
Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Steve Rae <srae@broadcom.com> Tested-by: Steve Rae <srae@broadcom.com> [Test HW: bcm235xx board]
tests: py: dfu: Provide functionality to set test and dummy files alt settings
After concatenation of "dfu_alt_info" variable from "dfu_alt_boot" and
"dfu_alt_system" it may happen that test and dummy files alt settings
are different than default 0 and 1.
This patch provides the ability to set different values for them.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- replace variables declarations with ones read from configuration file
- remove not necessary str() conversion at DFU host command generation
Changes for v2:
- generate "alt_info" automatically
- use file names as alt settings instead of numerical values
- extend in-code documentation
tests: py: dfu: Add functionality to set different u-boot's dfu env variable
By default (on almost all systems) the dfu env variable, which defines
available alt settings, is named as "dfu_alt_info".
However on some platforms (i.e. Odroid XU3), the 'dfu_alt_info' is concatenated
from other variables - namely 'dfu_alt_boot' and 'dfu_alt_system' at run time
(when one types 'dfu 0 mmc 0' for first time).
'dfu_alt_boot' describes alt settings which depend on boot medium - for example
boot loader's LBA sectors which are different on eMMC and SD card because of e.g.
MBR/GPT.
'dfu_alt_system' describes board agnostic alt settings - like rootfs, kernel.
On such system we can only append/modify this env variable.
Because of the above, we must have way to modify other than "dfu_ale_info"
variable to perform tests.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- None
Changes for v2:
- Rewrite of "alt_info_env_name" variable description
- Use of get() method on python's dictionary to easily obtain default
value
tests: py: dfu: Add variables to store dfu alt numbers for test and dummy files
This patch replaces hardcoded (i.e. 0 and 1) values passed to dfu_{read|write}
with variables.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- Replace per module global variables with ones defined inside a function
Changes for v2:
- None
Stefan Roese [Thu, 21 Apr 2016 06:19:42 +0000 (08:19 +0200)]
i2c: designware_i2c: Add support for PCI(e) based I2C cores (x86)
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Thu, 21 Apr 2016 06:19:41 +0000 (08:19 +0200)]
i2c: designware_i2c: Add DM support
This patch adds DM support to the designware I2C driver. It currently
supports DM and the legacy I2C support. The legacy support should be
removed, once all platforms using it have DM enabled.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
Stefan Roese [Thu, 21 Apr 2016 06:19:40 +0000 (08:19 +0200)]
i2c: designware_i2c: Prepare for DM driver conversion
This patch prepares the designware I2C driver for the DM conversion.
This is mainly done by removing struct i2c_adapter from the functions
that shall be used by the DM driver version as well.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
Stefan Roese [Thu, 21 Apr 2016 06:19:39 +0000 (08:19 +0200)]
i2c: designware_i2c: Integrate set_speed() into dw_i2c_set_bus_speed()
Integrating set_speed() into dw_i2c_set_bus_speed() will make the
conversion to DM easier for this driver.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
Stefan Roese [Thu, 21 Apr 2016 06:19:38 +0000 (08:19 +0200)]
i2c: designware_i2c: Add dw_i2c_enable() helper function
dw_i2c_enable() is used to dis-/en-able the I2C controller. It makes
sense to add such a function, as the controller is dis-/en-abled
multiple times in the code. Additionally, this function now checks,
if the controller is really dis-/en-abled. This code is copied
from the Linux I2C driver version.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Thu, 21 Apr 2016 06:19:37 +0000 (08:19 +0200)]
i2c: designware_i2c: Add ic_enable_status to ic_regs struct
Add the ic_enable_status register to the i2c_regs struct. Additionally
the register offsets are added, to better check, if the offset matches
the register description in the datasheet.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
Stefan Roese [Thu, 21 Apr 2016 05:11:34 +0000 (07:11 +0200)]
dm: core: Add dev_get_addr_ptr() to return a pointer to the reg address
On some platforms (e.g. x86), the return value of dev_get_addr() can't
be assigned to a pointer type variable directly. As there might be a
difference between the size of fdt_addr_t and the pointer type. On
x86 for example, "fdt_addr_t" is 64bit but "void *" only 32bit. So
assigning the register base directly in dev_get_addr() results in this
compilation warning:
warning: cast to pointer from integer of different size
This patch introduces the new function dev_get_addr_ptr() that
returns a pointer to the 'reg' address that can be used by drivers
in this case.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current table look-up for the DTB file name turned out bothersome
in terms of maintainability; I ended up adding a new entry every time
a new board is supported.
There is a common pattern between the DT compatible string and the
corresponding file name; drop the vendor prefix "socionext," and
prefix it with "uniphier-" and suffix it with ".dtb".
projects / u-boot.git / log