When env support is disabled then usage of env_get_f() generates linker
errors. So do not compile env_get_f() when env support is disabled (for
example when disabled only in SPL).
When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
mmc: mmc_mode_name() is used also when LOGLEVEL >= LOGL_DEBUG
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.
Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.
So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.
mmc: fsl_esdhc_spl: pre-PBL: check for BOOT signature instead of MBR/DBR
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.
So add check for BOOT signature and remove check for MBR/DBR.
This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.
powerpc: mpc85xx: Rename _start_e500 symbol to _start
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Stephen Carlson [Tue, 29 Mar 2022 21:51:10 +0000 (14:51 -0700)]
armv8/fsl-lsch3: Suppress spurious warning on Layerscape CPUs
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 22 Apr 2022 09:23:27 +0000 (14:53 +0530)]
armv8: layerscape: get rid of smc_call()
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 28 Feb 2022 12:48:37 +0000 (13:48 +0100)]
armv8: include psci_update_dt() unconditionally
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sean Anderson [Fri, 22 Apr 2022 08:31:36 +0000 (14:01 +0530)]
arm: layerscape: Disable erratum A009007 on LS1021A, LS1043A, and LS1046A
This erratum is reported to cause problems on these processors [1-3].
The problem is usually with the clocking, which is supposed to be
configured by the RCW [4]. However, if it is not set, or if the default
clocking is not correct, then this erratum will cause an SError.
However, according to Ran Wang in [1]:
" ... this erratum is used to pass USB compliance test only, you could
disable this workaround on your board if you don't any USB issue on
normal use case, I think it's fine."
So just disable this erratum by default for these processors.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Tom Rini [Sat, 23 Apr 2022 12:06:28 +0000 (08:06 -0400)]
Merge branch '2022-04-22-assorted-updates'
- Add "-q" to fdt addr and use it in distro_bootcmd to make the user
experience less scary reading in normal try/fail cases.
- Let the adc update an environment variable like many other commands do
- Fix TPL SEPARATE_BSS check when locating DTB
- Allow ":" in PXE file names again
- Two Apple M1 fixes
Mark Kettenis [Tue, 19 Apr 2022 19:20:31 +0000 (21:20 +0200)]
arm: apple: Point stdout-path to framebuffer when keyboard present
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Janne Grunau <j@jannau.net> Tested-by: Janne Grunau <j@jannau.net>
Mark Kettenis [Tue, 19 Apr 2022 19:10:29 +0000 (21:10 +0200)]
arm: apple: Don't clear framebuffer
Enable CONFIG_NO_FB_CLEAR to preserve the Asahi logo. Since that
logo is drawn on a black background also enable
CONFIG_SYS_WHITE_ON_BLACK such that text printed by U-Boot is still
visible.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Lyle Franklin [Sat, 16 Apr 2022 15:36:43 +0000 (11:36 -0400)]
Allow colon in PXE bootfile URLs
- U-boot's PXE flow supports prefixing your bootfile name with an
IP address to fetch from a server other than the DHCP server,
e.g. `hostIPaddr:bootfilename`:
https://github.com/u-boot/u-boot/commit/a93907c43f847f076dd0e34ee3b69b5e8e6d0d29
- However, this breaks bootfile paths which contain a colon, e.g.
`f0:ad:4e:10:1b:87/7/pxelinux.cfg/default`
- This patch checks whether the `hostIPaddr` prefix is a valid
IP address before overriding the serverIP otherwise the whole
bootfile path is preserved
Signed-off-by: Lyle Franklin <lylejfranklin@gmail.com>
The documentation for CONFIG_IS_ENABLED() in include/linux/kconfig.h
implies that we will get the correct behaviour, but the actual behaviour
differs such that this condition is now always false.
This stopped TPL being able to load the device tree blob at least on the
ROCKPro64 board (RK3399 SoC), since the wrong device tree location was
chosen.
The issues causing this behaviour with CONFIG_IS_ENABLED() are:
1. The documentation implies that CONFIG_SPL_BUILD =>
CONFIG_SPL_<option> is considered before the TPL equivalent.
Actually, the TPL options have higher priority - see definition of
_CONFIG_PREFIX.
2. The documentation implies a fallthrough, eg. if CONFIG_SPL_BUILD is
defined but the CONFIG_SPL_<option> is not, then it will proceed to
check if CONFIG_TPL_BUILD
Actually, if CONFIG_TPL_BUILD is defined, then it stops there
and CONFIG_SPL_BUILD is not considered - see definition of
_CONFIG_PREFIX.
During TPL build, at least for the ROCKPro64, both CONFIG_TPL_BUILD
and CONFIG_SPL_BUILD are defined, but because of the above, only TPL
options are considered. Since there is no CONFIG_TPL_SEPARATE_BSS,
this fails.
Fixes: 690af71850 ("fdt: Correct condition for SEPARATE_BSS") Signed-off-by: Andrew Abbott <andrew@mirx.dev>
Sean Anderson [Wed, 23 Mar 2022 18:26:09 +0000 (14:26 -0400)]
power-domain: Fix use of uninitialized value in dev_power_domain_ctrl
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Michal Simek [Wed, 9 Mar 2022 09:05:45 +0000 (10:05 +0100)]
usb: dwc3: Add support for usb3-phy PHY configuration
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Jim Liu [Fri, 1 Apr 2022 09:59:39 +0000 (17:59 +0800)]
wdt: nuvoton: Add support for Nuvoton
Add watchdog controller driver for NPCM7xx/npcm8xx
the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 21 Apr 2022 23:55:38 +0000 (19:55 -0400)]
Merge branch '2022-04-21-further-cleanups'
- Fix SPL_SYS_MALLOC_SIMPLE and non-SPL_FRAMEWORK boards (a large number
of PowerPC platforms)
- Remove duplication of crc16 functionality
- Migrate COUNTER_FREQUENCY to CONFIG_COUNTER_FREQUENCY and have it in
Kconfig
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b88. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Peng Fan [Wed, 13 Apr 2022 09:47:19 +0000 (17:47 +0800)]
arch: arm: Kconfig: set default COUNTER_FREQUENCY
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
fs: ext4: Use CRC-16 implementation from linux/crc16.h
Implementation in linux/crc16.h provides standard CRC-16 algorithm with
polynomial x^16 + x^15 + x^2 + 1. Use it and remove duplicate ext4 CRC-16
specific code.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
crc16-ccitt: Rename file with CRC-16-CCITT implementation to crc16-ccitt.c
U-Boot CRC-16 implementation uses polynomial x^16 + x^12 + x^5 + 1 which is
not standard CRC-16 algorithm, but it is known as CRC-16-CCITT. Rename file
crc16.c to crc16-ccitt.c to reduce confusion.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Inspection showed that gd->malloc_limit is zero. And it is because
generally SPL_FRAMEWORK initialize SPL's gd->malloc_limit. But when
SPL_FRAMEWORK is not enabled then in most cases nobody initialize
gd->malloc_limit and so SPL malloc simple does not work.
So disable SPL_SYS_MALLOC_SIMPLE by default when SPL_FRAMEWORK is not
enabled. SPL_SYS_MALLOC_SIMPLE can be disabled only by setting
SPL_SYS_MALLOC_F_LEN to zero. So do it.
This change fixes SPL error "alloc space exhausted" on P2020 board.
Tom Rini [Thu, 21 Apr 2022 14:56:58 +0000 (10:56 -0400)]
Merge branch '2022-04-21-assorted-improvements'
- For the environment, add a arch_env_get_location hook and make use of
it on some NXP platforms (so that boards can override SoCs).
- Remove some unused squashfs code from SPL
- Resync am335x beaglebone related DTS files
- Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Cc: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Sean Anderson [Tue, 12 Apr 2022 14:59:04 +0000 (10:59 -0400)]
treewide: Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Paul Barker [Mon, 11 Apr 2022 15:42:01 +0000 (15:42 +0000)]
board: ti: am335x: Add support for BBE Extended WiFi
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:42:00 +0000 (15:42 +0000)]
board: ti: am335x: Add BBE Lite support
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:41:59 +0000 (15:41 +0000)]
arm: dts: Resync dts for BeagleBone and derivatives
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:34 +0000 (02:21 +0200)]
ARM: imx: imx8m: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:33 +0000 (02:21 +0200)]
armv8: layerscape: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Thu, 14 Apr 2022 13:51:46 +0000 (15:51 +0200)]
ARM: imx: imx8m: Fix board_get_usable_ram_top()
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: e27bddff4b9 ("imx8m: Restrict usable memory to space below 4G boundary") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tim Harvey [Wed, 13 Apr 2022 22:57:37 +0000 (15:57 -0700)]
pci: imx: remove weak overrides no longer used
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.
Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Wed, 13 Apr 2022 22:54:37 +0000 (15:54 -0700)]
pci: imx: use vpcie-supply if defined by device-tree
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD) Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD) Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD) Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD) Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tony Dinh [Sun, 17 Apr 2022 23:42:32 +0000 (16:42 -0700)]
arm: kirkwood: Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Tim Harvey [Wed, 13 Apr 2022 18:31:09 +0000 (11:31 -0700)]
board: gateworks: venice: add imx8mp-venice-gw740x support
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Tim Harvey [Wed, 13 Apr 2022 18:31:08 +0000 (11:31 -0700)]
board: gateworks: venice: add additional levels for dtb name match
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb
Tim Harvey [Wed, 13 Apr 2022 16:29:16 +0000 (09:29 -0700)]
board: gateworks: gw_ventana: use comomn GSC driver
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Tim Harvey [Wed, 13 Apr 2022 16:09:49 +0000 (09:09 -0700)]
imx8m{m,n}-venice-gw7902: add support for GPY111 phy
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- add tx-delay/rx-delay config
projects / u-boot.git / log