Simon Glass [Sat, 7 Dec 2019 04:41:51 +0000 (21:41 -0700)]
x86: Drop unnecessary cpu code for TPL
We don't need to know every detail about the CPU in TPL. Drop some
superfluous functions to reduce code size. Add a simple CPU detection
algorithm which just supports Intel and AMD, since we only support TPL
on Intel, so far.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:50 +0000 (21:41 -0700)]
x86: timer: Reduce timer code size in TPL on Intel CPUs
Most of the timer-calibration methods are not needed on recent Intel CPUs
and just increase code size. Add an option to use the known-good way to
get the clock frequency in TPL. Size reduction is about 700 bytes.
Note that version 1 of this commit caused bootstage to crash since the CPU
was not identified. This is corrected by changes previously applied to
make sure that the CPU is identified before spl_init() is called, such as
39146a2e0b x86: Move CPU init to before spl_init()
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:49 +0000 (21:41 -0700)]
x86: timer: use a timer base of 0
On x86 platforms the timer is reset to 0 when the SoC is reset. Having
this as the timer base is useful since it provides an indication of how
long it takes before U-Boot is running.
When U-Boot sets the timer base to something else, time is lost and we
no-longer have an accurate account of the time since reset. This
particularly affects bootstage.
Change the default to not read the timer base, leaving it at 0. Add an
option for when U-Boot is the secondary bootloader.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:46 +0000 (21:41 -0700)]
board_r: Move early-timer init later
At present the early timer init happens as soon as driver model is set up.
This makes it impossible to do anything that needs driver model but must
run before devices are probed (as needed with Intel's FSP-S, for example).
In any case it is not a good idea to tie probing of particular drivers too
closely to the DM init.
Create a new function to init the timer and put it a bit later in the
sequence.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:44 +0000 (21:41 -0700)]
fdt: Show the preprocessed .dts file on error
When device-tree compilation fails it is sometimes tricky to see which
line is broken, since the input file to dtc is a pre-processed version
of the device tree.
Add a line that points to the file that needs to be checked:
When the error is in the main .dts file, output is something like this:
output: 'Error: arch/x86/dts/.chromebook_coral.dtb.pre.tmp:478.46-47
syntax error
FATAL ERROR: Unable to parse input tree
but in fact looking at that file shows nothing useful:
This shows that the filename (normally "fitimage.bin") has not been
inserted the preprocess, leading to the realisation that the value should
be CONFIG_IFWI_INPUT_FILE.
If the above does not make sense, I encourage people to try introducing
errors in the device tree preprocessed values.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:43 +0000 (21:41 -0700)]
x86: spi: Add helper functions for Intel Fast SPI
Most x86 CPUs use a mechanism where the SPI flash is mapped into the very
top of 32-bit address space, so that it can be executed in place and read
simply by copying from memory. For an 8MB ROM the mapping starts at
0xff800000.
However some recent Intel CPUs do not use a simple 1:1 memory map. Instead
the map starts at a different address and not all of the SPI flash is
accessible through the map. This 'Fast SPI' feature requires that U-Boot
check the location of the map. It is also possible (optionally) to read
from the SPI flash using a driver.
Add support for booting from Fast SPI. The memory-mapped version is used
by both TPL and SPL on Apollo Lake.
In respect of a SPI flash driver, the actual SPI driver is ich.c - this
just adds a few helper functions and definitions.
This is used by Apollo Lake.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:42 +0000 (21:41 -0700)]
i2c: designware: Support use in SPL
Allow this driver to set up an IO address in SPL using an 'early-regs'
property. This allows SPL to use the I2C driver without having to enable
the full PCI stack.
Also split out ofdata_to_platdata in designware driver since this is more
correct, and more convenient for the new logic.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:40 +0000 (21:41 -0700)]
i2c: designware: Tidy up PCI support
This is hacked into the driver at present. It seems better to have it as
a separate driver that uses the base driver. Create a new file and put
the X86 code into it.
Actually the Baytrail settings should really come from the device tree.
Note that 'has_max_speed' is added as well. This is currently always false
but since only Baytrail provides the config, it does not affect operation
for other devices.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:39 +0000 (21:41 -0700)]
net: Move the checksum functions to lib/
These functions are used by code outside the network support, so move them
to lib/ to be more accessible.
Without this, the functions are only accessible in SPL/TPL only if
CONFIG_SPL/TPL_NET are defined. Many boards do not enable those option but
still want to do checksums in this format.
Fix up a few code-style nits while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:38 +0000 (21:41 -0700)]
dm: pci: Move pci_get_devfn() into a common file
Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:37 +0000 (21:41 -0700)]
dm: pci: Allow delaying auto-config until after relocation
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:36 +0000 (21:41 -0700)]
dm: core: Fix offset_to_ofnode() with invalid offset
If the offset is -1 this function correctly sets up a null ofnode. But if
the offset is any other negative number (e.g. -FDT_ERR_BADPATH) then it
does the wrong thing.
An offset of -1 in ofnode indicates that the ofnode is not valid. Any
other negative value is not handled by ofnode_valid(). We could of course
change that function, but it seems much better to always use the same
value for an invalid node.
Fix it by setting the offset to -1 if it is invalid for any reason.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:35 +0000 (21:41 -0700)]
dm: gpio: Allow control of GPIO uclass in SPL
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:41:34 +0000 (21:41 -0700)]
binman: Add a library to access binman entries
SPL and TPL can access information about binman entries using link-time
symbols but this is not available in U-Boot proper. Of course it could be
made available, but the intention is to just read the device tree.
Add support for this, so that U-Boot can locate entries.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Wed, 11 Dec 2019 13:17:19 +0000 (08:17 -0500)]
Merge tag 'fix-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c bugfixes for 2020.01
- i2c: i2c_cdns: fix write timeout on fifo boundary
fixes timout issue when writting number of bytes is multiple
of the FIFO depth.
Tom Rini [Wed, 11 Dec 2019 13:16:16 +0000 (08:16 -0500)]
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
The rpi_4_32b_defconfig states that only one DRAM bank is present. This
leads to a wrong configuration of the available DRAM. Fix this by
setting the DRAM bank config accordingly.
Up to now we only update the DRAM banks when we are define
CONFIG_BCM2711. But our one binary approach uses a config that supports
BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on
Raspberry Pi 4, even if it has more RAM.
Fix this by calling dram_init_banksize.
Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4") Signed-off-by: Matthias Brugger <mbrugger@suse.com>
To update the dram bank information from device-tree we use
fdtdec_decode_ram_size() which expectes the the size-cells and
address-cells to be defined in the memory node. For normal system RAM
these values are defined in the root node. When the values differ from
the default values defined in the spec, we can end up with wrong RAM
bank information.
Switch to the "standard" way to update the RAM bank information to
avoid this.
Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization") Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Michael Auchter [Mon, 9 Dec 2019 18:16:16 +0000 (18:16 +0000)]
i2c: i2c_cdns: fix write timeout on fifo boundary
This fixes an issue that would cause I2C writes to timeout when the
number of bytes is a multiple of the FIFO depth (i.e. 16 bytes).
Within the transfer loop, after writing the data register with a new
byte to transfer, if the transfer size equals the FIFO depth, the loop
pauses until the INTERRUPT_COMP bit asserts to indicate data has been
sent. This same check is performed after the loop as well to ensure data
has been transferred prior to returning.
In the case where the amount of data to be written is a multiple of the
FIFO depth, the transfer loop would wait for the INTERRUPT_COMP bit to
assert after writing the final byte, and then wait for this bit to
assert once more. However, since the transfer has finished at this
point, no new data has been written to the data register, and hence
INTERRUPT_COMP will never assert.
Fix this by only waiting for INTERRUPT_COMP in the transfer loop if
there's still data to be written.
Signed-off-by: Michael Auchter <michael.auchter@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 6 Dec 2019 20:31:31 +0000 (15:31 -0500)]
buildman: Ignore blank lines during size checks
Today when parsing the .sizes files we get a warning about an invalid
line in the file as it's blank. Solve this by checking that we have a
non-blank line prior to processing.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 5 Dec 2019 22:59:14 +0000 (15:59 -0700)]
buildman: Add options to get the arch and toolchain info
Sometimes it is useful for external tools to use buildman to provide the
toolchain information. Add an -a option which shows the value to use for
the ARCH environment variable, and -A which does the same for
CROSS_COMPILE
Simon Glass [Thu, 5 Dec 2019 22:59:13 +0000 (15:59 -0700)]
buildman: Figure out boards before commits
At present buildman looks at toolchains, then commits and then boards.
Move the board processing up above the commit processing, since it relates
to the toolchain code. This will make it easier to check the toolchains
needed for a board without processing commits first.
Tom Rini [Tue, 10 Dec 2019 20:41:15 +0000 (15:41 -0500)]
Merge tag 'fixes-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix crash and board reset when drawing RLE8 bitmaps
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
buildman: Improve [make-flags] section parser to allow quoted strings
The parser responsible for the '[make-flags]' section in
the '.buildman' settings file is currently not able to
handle quoted strings, as given in the sample bellow:
This patch replaces the simple string splitter based on the <space>
delimiter with a regex tokenizer that preserves spaces inside double
quoted strings.
Due to a conversion error the sandbox does not accept byte values 0x80-0xff
from the keyboard. The UEFI extended text input unit test requires Unicode
support.
Use unsigned char for the serial buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Swapna Gurumani [Mon, 2 Dec 2019 21:06:10 +0000 (21:06 +0000)]
configs: sama5d27_som1_ek: Add default config to read ENV from QSPI
In the initial SPI flash setup, the default bus mode being used was 3,
which is incorrect, causing a CRC error when the ENV was being read from
QSPI. Setting the default bus mode to 0 which is the correct mode.
Tom Rini [Tue, 10 Dec 2019 02:53:23 +0000 (21:53 -0500)]
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
Lukas Auer [Sun, 8 Dec 2019 22:28:52 +0000 (23:28 +0100)]
spl: opensbi: wait for ack from secondary harts before entering OpenSBI
At the start, OpenSBI relocates itself to its link address. If the link
address ranges of U-Boot SPL and OpenSBI overlap, the relocation can
lead to code corruption if a hart is still running U-Boot SPL during
relocation. To avoid this problem, the main hart is specified as the
preferred boot hart to perform the relocation. This fixes the code
corruption problems based on the assumption that since the main hart
schedules the secondary harts to enter OpenSBI, it will be the last to
enter OpenSBI. However it was reported that this assumption is not
always correct.
To make sure the assumption always holds true, wait for all secondary
harts to acknowledge the call-function request before entering OpenSBI
on the main hart.
Reported-by: Rick Chen <rick@andestech.com> Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 8 Dec 2019 22:28:51 +0000 (23:28 +0100)]
riscv: add option to wait for ack from secondary harts in smp functions
Add a wait option to smp_call_function() to wait for the secondary harts
to acknowledge the call-function request. The request is considered to
be acknowledged once each secondary hart has cleared the corresponding
IPI.
As part of the call-function request, the secondary harts invalidate the
instruction cache after clearing the IPI. This adds a delay between
acknowledgment (clear IPI) and fulfillment (call function) of the
request. We want to use the acknowledgment to be able to judge when the
request has been completed. Remove the delay by clearing the IPI after
cache invalidation and just before calling the function from the
request.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 8 Dec 2019 22:28:50 +0000 (23:28 +0100)]
riscv: add functions for reading the IPI status
Add the function riscv_get_ipi() for reading the pending status of IPIs.
The supported controllers are Andes' Platform Level Interrupt Controller
(PLIC), the Supervisor Binary Interface (SBI), and SiFive's Core Local
Interruptor (CLINT).
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Rick Chen <rick@andestech.com>
Lukas Auer [Sun, 8 Dec 2019 22:28:49 +0000 (23:28 +0100)]
spl: opensbi: specify main hart as preferred boot hart
OpenSBI uses a relocation lottery to determine the hart to relocate
OpenSBI to its link address. In the U-Boot SPL boot flow, the main hart
schedules the secondary harts to enter OpenSBI before doing so itself.
One of the secondary harts will therefore always be the winner of the
relocation lottery. This is problematic if the link address ranges of
OpenSBI and U-Boot SPL overlap. OpenSBI will be relocated and therefore
overwrite U-Boot SPL while some harts may still run it, leading to code
corruption.
Avoid this problem by specifying the main hart as the preferred boot
hart to perform the OpenSBI relocation. The main hart will be the last
hart to enter OpenSBI, relocation can therefore occur safely.
The boot hart field was added to version 2 of the OpenSBI FW_DYNAMIC
info structure. The header file include/opensbi.h is synchronized with
include/sbi/fw_dynamic.h from the OpenSBI project to update the info
structure. The header file is recent as of commit 7a13beb21326 ("firmware: Add preferred boot HART field in struct
fw_dynamic_info").
Reported-by: Rick Chen <rick@andestech.com> Suggested-by: Anup Patel <Anup.Patel@wdc.com> Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
Rick Chen [Thu, 14 Nov 2019 05:52:27 +0000 (13:52 +0800)]
riscv: Fix clear bss loop in the start-up code
For RV64, it will use sd instruction to clear t0
register, and the increament will be 8 bytes. So
if the difference between__bss_strat and __bss_end
was not 8 bytes aligned, the clear bss loop will
overflow and acks like system hang.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
Rick Chen [Thu, 14 Nov 2019 05:52:24 +0000 (13:52 +0800)]
riscv: andes_plic: Fix some wrong configurations
Fix two wrong settings of andes plic driver as below:
1. Fix wrong pending register base definition.
2. Declaring the en variable in enable_ipi() as unsigned int instead of
int can help to fix wrong plic enabling setting in RV64.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
Rick Chen [Thu, 14 Nov 2019 05:52:23 +0000 (13:52 +0800)]
riscv: ax25-ae350: Use generic memory size setup
To get memory size from device tree instead of
get_ram_size(). This can avoid memory access fault
in U-Boot proper after PMP configurations in OpenSBI.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
Rick Chen [Thu, 14 Nov 2019 05:52:22 +0000 (13:52 +0800)]
riscv: ax25-ae350: add SPL configuration
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
Rick Chen [Thu, 14 Nov 2019 05:52:21 +0000 (13:52 +0800)]
riscv: ax25: add SPL support
The U-Boot SPL will boot in M mode and load the FIT image which
include OpenSBI and U-Boot proper images. After loading progress,
it will jump to OpenSBI first and then U-Boot proper which will
run in S mode.
Also remove V5L2_CACHE due to U-Boot SPL code size consideration.
Without this concern, it can be enable manually for performance.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
Rick Chen [Wed, 4 Dec 2019 06:52:46 +0000 (14:52 +0800)]
Use dts support from U-Boot via OF_SEPARATE instead of depending from opensbi.
This would help to make the necessary changes in drivers and device trees
in U-Boot tree itself. This feature would also be helpful to not pass
dtb during opensbi builds.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Signed-off-by: Rick Chen <rick@andestech.com>
Idea is to periodically sync the dts from Linux instead of
tweaking internal changes one after another, so better not
add any intermediate changes in between. This would help to
maintain the dts files easy and meaningful since we are
reusing device tree files from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 20 Oct 2019 18:53:47 +0000 (20:53 +0200)]
riscv: increase stack size to avoid a stack overflow during distro boot
This fixes a problem, where booting Linux using distro boot will
sometimes lead to an invalid instruction exception on the main hart. The
secondary harts are not affected and boot Linux successfully. The root
cause of this problem is a stack overflow on the main hart.
With distro boot, the current default stack size of 8KiB on RISC-V is
not sufficient and will cause a stack overflow. The stacks are allocated
sequentially. In the case of a stack overflow the stack of the main hart
can reach into that of another hart and be corrupted.
The stack overflow previously did not cause any problems, because only
stack frames, which are not used anymore since the hart enters Linux,
were corrupted. Starting with GCC 9, the stack usage has decreased. Now,
only the most recent stack frame overflows into the stack of a secondary
hart and is corrupted. The illegal instruction exception is caused by
the secondary hart overwriting the return address in the stack frame of
the main hart with an address that does not include valid code.
Increase the default stack size of each hart to 16KiB to avoid this
problem.
Reported-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Tested-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Rick Chen <rick@andestech.com>
Suman Anna [Mon, 2 Dec 2019 22:34:21 +0000 (16:34 -0600)]
ARM: DRA7: Fixup DSP OPP_HIGH clock rate on DRA76P/DRA77P SoCs
The commit 1b42ab3eda8a ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") added the core logic to update the kernel
device-tree blob to adjust the DSP, IVA and GPU DPLL clocks based on
a one-time OPP choice selected in U-Boot for most of the DRA7xx/AM57xx
family of SoCs.
The DSPs on DRA76xP/DRA77xP SoCs (DRA76x ACD package SoCs) though
provide a higher performance and can run at a higher clock frequency
of 850 MHz at OPP_HIGH instead of 750 MHz. Fix up the logic to use the
correct clock rates on these SoCs. Note that this higher clock rate is
not applicable to other Jacinto 6 Plus SoCs (DRA75xP/DRA74xP SoCs or
AM574x SoCs) that follow the ABZ package.
Signed-off-by: Suman Anna <s-anna@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Ben Wolsieffer [Thu, 28 Nov 2019 05:07:08 +0000 (00:07 -0500)]
cmd: pxe: Increase maximum path length
On NixOS, cross compiled kernels have long suffixes that cause them to
exceed the current maximum path length. The PXE/TFTP max path length is
used for extlinux.conf support as well, which is where this problem
usually manifest's itself.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: ti: am65-cpsw-nuss: Rework RX flow ID handling
Get flow ID information for RX DMA channel using dma_get_cfg() interface
instead of reading from DT. This is required in order to avoid DT update
whenever there is change in the range of flow ID allocated to the host.
Implement dma_get_cfg() interface to pass flow id information for DMA
clients to use. This is needed because on K3 SoCs, CPSW (ethernet) and
UDMA (DMA provider) support "flows" within a given RX DMA channel. This
allows different network packets to be segregated while using same RX
DMA channel. In order for basic ethernet to work, CPSW slave must be
aware of the flow ID allocated for the RX channel by the DMA driver.
This interface allows CPSW to query flow ID from DMA provider and
configure it in CPSW HW.
Sometimes, there would be a need to exchange data between DMA provider
and DMA client which are very specific to DMA driver of the SoC/platform
and are not generic enough to be put into struct dma. Therefore, introduce
dma_get_cfg() interface to get DMA provider specific data from client
device. Clients can use unique configuration ID flags to get different
configuration data from DMA driver.
Cédric Le Goater [Thu, 28 Nov 2019 12:37:04 +0000 (13:37 +0100)]
net: ftgmac100: align RX/TX descriptors on ARCH_DMA_MINALIGN
Fixes: e766849713ff ("net: ftgmac100: convert the RX/TX descriptor arrays") Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Mon, 25 Nov 2019 15:57:27 +0000 (17:57 +0200)]
drivers: net: fsl_enetc: register internal MDIO bus
This bus is used to access internal SoC PHYs. These PHYs are configured
by the ENETC driver directly, but it's useful to have command line access
to this MDIO to debug the system especially when using new external PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:58:47 +0000 (18:58 +0200)]
drivers: net: fsl_enetc_mdio: return with time-out if HW is stuck
On some boards MDIO may get stuck if it detects echo on the line. This is
a know hardware issue, there is a board fix for it. In case we're running
on a board that doesn't have the fix, we don't want to loop here forever
and freeze U-Boot.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:58:46 +0000 (18:58 +0200)]
drivers: net: fsl_enetc: move PCS and PHY config to probe
This reduces the time needed to establish a link as we don't reset the link
each time the interface is used. Our Link capabilities do not change at
run-time so there is no need to re-apply PHY configuration each time.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Mon, 25 Nov 2019 15:15:12 +0000 (17:15 +0200)]
net: mdio-uclass: add dm_eth_phy_connect helper function
The function connects an ethernet device to a PHY using DT information.
This API is only available for eth devices with an associated device tree
node.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Mon, 25 Nov 2019 15:15:11 +0000 (17:15 +0200)]
net: mdio-uclass: rename arguments of dm_mdio_phy_connect for clarity
Renamed dm_mdio_phy_connect arguments dev to mdiodev and addr to phyaddr
for a bit more clarity and consistency with the following patches.
Also use NULL instead of 0 on error return path.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Sat, 23 Nov 2019 17:58:59 +0000 (17:58 +0000)]
net: tftp: Fix too small block size
Commit b618b3707633 ("net: Convert CONFIG_TFTP_BLOCKSIZE to Kconfig")
accidentally set the default *option* TFTP block size to 512 bytes, even
though the comment in the code says that this is a terrible choice. Most
boards didn't define the symbol before, so they got the default block size
of 1468 bytes before, but now use 512 bytes, which is also the fallback.
This leads to both abysmal performance and a lot of hashes printed
on the screen (one character for every 5K), which is both annoying and
slow over serial links.
Set the default block size in Kconfig back to the value it had before.
This improves TFTP performance from 2.8 MB/s to 6.9 MB/s on a Pine64.
Fixes: b618b3707633 ("net: Convert CONFIG_TFTP_BLOCKSIZE to Kconfig") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:37 +0000 (18:28 +0200)]
doc: bindings: Aquantia PHY node binding
A couple of optional properties have been introduced for Aquantia PHY
allowing the driver to set up wiring related configuration points that
are otherwise driven by firmware.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:36 +0000 (18:28 +0200)]
doc: bindings: add bindings document for PHY nodes
It defines that PHY nodes must be children on MDIO bus nodes and defines
the only required property in U-Boot, reg. This property along with the
example provided are copied over from Linux.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:35 +0000 (18:28 +0200)]
drivers: net: aquantia: check system interface too when checking for link up
In some cases the link on the system interface of the aquantia PHY comes up
after the link on line interface. The link state loop only checks the line
side, which may result in first packet sent being lost.
Use aquantia_link_is_up instead, which checks both system and line side on
gen 2/3 PHYs to avoid losing the 1st packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:34 +0000 (18:28 +0200)]
drivers: net: aquantia: set SMBus addr based on DT property
Aquantia PHYs have a SMBus interface mostly used for debug. The addresses
on this interface are normally set up by PHY firmware, but depending on the
board they may end up not being unique. Add an optional DT property used
to change SMBus address if needed.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:33 +0000 (18:28 +0200)]
drivers: net: aquantia: set MDI reversal based on DT property
MDI pins up to the RJ45 connector may be reversed on the board and the
default PHY configuration applied by firmware may or may not match that.
Add an optional DT property to configure MDI reversal for this case.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:32 +0000 (18:28 +0200)]
drivers: net: aquantia: set up SI protocol based on interface type
If PHY is not ready for data by the time _config is called, reconfigure the
PHY system interface to use the proper protocol based on phydev->interface,
just in case the defaults set by PHY firmware don't match current
configuration.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:31 +0000 (18:28 +0200)]
drivers: net: aquantia: add PHY generation information
Uses the data field in phy_driver structure to identify the PHY generation.
This is useful for custom configuration as non-generic PHY registers are
not 100% compatible between generations.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:30 +0000 (18:28 +0200)]
drivers: net: aquantia: use XFI, USXGMII interface types
The PHY supports XFI and USXGMII, the notable difference being that USX AN
is enabled for USXGMII. Legacy code uses XGMII for any 10G proto and
detects whether USX AN should be enabled or not using a PHY status
register. Keep that functionality too, so we don't break existing drivers.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Thu, 14 Nov 2019 16:28:28 +0000 (18:28 +0200)]
include: phy: define XFI and USXGMII interface types
Drivers currently use XGMII for XFI and USXGMII and, where needed, use
other information to identify the actual protocol on the board. With these
two defined drivers can now rely on DT phy-mode property.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: mv88E61xx: fix ENERGY_DET init for mv88E6071
On mv88E6071 the 'EDet' field offset, width and sense control
bits are different, adjust the driver to init the PHY control
register as needed. This fixes not working link detection and
tftp transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: mv88e61xx: add CPU port parameter init for 88E6071
On 88E6071 chip the port status register bit field offsets
for duplex and link bits differ. Extend the driver to use 88E6071 specific offset values. The width of bit fields for
speed status differ, too. Adapt for proper port speed
detection on 88E6071.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Extend the driver to init switch register offsets from variables
instead of compile time macros and enable detection of 88E6071 and
compatible devices. Ethernet transfer (e.g. tftp) does not work yet,
so enable the registration of the 'indirect mii' bus for easier PHY
register access by 'mii' command.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nicolas Ferre [Wed, 23 Oct 2019 10:46:44 +0000 (10:46 +0000)]
net: phy: micrel: make sure the factory test bit is cleared
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michael Walle [Mon, 21 Oct 2019 23:03:10 +0000 (01:03 +0200)]
net: eth-uclass: ignore unavailable devices
device_probe() may fail in which case the seq_id will be -1. Don't
display these devices during startup. While this is only a cosmetic
change, the return value of eth_initialize() will also change to the
actual number of available devices. The return value is only used in
spl_net to decide whether there are any devices to boot from. So
returning only available devices is also more correct in that case.
Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Florin Chiculita [Mon, 14 Oct 2019 14:27:07 +0000 (17:27 +0300)]
net: phy: aquantia: wait for phy init sequence to finish
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Josef Holzmayr [Wed, 2 Oct 2019 19:22:52 +0000 (21:22 +0200)]
net: macb: let miiphy_read/_write pass arbitrary addresses
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Josef Holzmayr [Wed, 2 Oct 2019 19:22:51 +0000 (21:22 +0200)]
net: macb: explicitly pass phy_adr to mdio read and write
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stefan Roese [Mon, 30 Sep 2019 08:26:42 +0000 (10:26 +0200)]
net: phy: Increase link up delay in genphy_update_link()
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Weijie Gao <weijie.gao@mediatek.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ramon Fried [Fri, 13 Sep 2019 15:25:03 +0000 (18:25 +0300)]
cmd: mdio/mii: add Kconfig help and allow break dependency
* Add Kconfig help describing the purpose of each command.
* Add CONFIG_CMD_MDIO so it could be selected individually, as
it doesn't depend on the mii command.
* Add Kconfig imply to mii to automatically select the mdio
command.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nevo Hed [Thu, 15 Aug 2019 22:08:44 +0000 (18:08 -0400)]
net: mvpp2: use new MVMDIO driver
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Nevo Hed [Thu, 15 Aug 2019 22:08:43 +0000 (18:08 -0400)]
arm: dts: armada-cp110-*dtsi: add xmdio nodes
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.
However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec. Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.
projects / u-boot.git / log