Wolfgang Denk [Sun, 29 Apr 2012 23:57:39 +0000 (23:57 +0000)]
doc: cleanup - move board READMEs into respective board directories
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Jason Jin <jason.jin@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's
GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757,
the driver handles the GETHER.
At least on i.MX25, the RMII mode did not work, which is fixed by this patch.
The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set
it accordingly.
According to the xMII and 7-wire (aka GPSI) standards, full duplex should be
available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may
support full duplex for 7-wire too, but the reference manual does not say that,
so avoid an invalid assumption. Actually, the choice between half and full
duplex also depends on the endpoint/switch/repeater configuration, so a config
option could be added for that, but there has been no need for it so far.
NFS_TIMEOUT is constant value defined in net/nfs.c. But sometimes it needs to adjust.
This patch enables to override NFS_TIMEOUT by defining CONFIG_NFS_TIMEOUT in a board specific config file.
Wolfgang Denk [Thu, 12 Jul 2012 06:23:58 +0000 (08:23 +0200)]
Merge branch 'next' of git://git.denx.de/u-boot-net into next
* 'next' of git://git.denx.de/u-boot-net:
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Wolfgang Denk [Thu, 12 Jul 2012 06:17:29 +0000 (08:17 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
mx28evk: Add I2C support
mxs-i2c: Fix internal address byte order
mxc_i2c: remove setting speed at each start
mx6qsabrelite: add i2c support
mxc_i2c: specify i2c base address in config file
Rob Herring [Sat, 14 Apr 2012 18:06:49 +0000 (18:06 +0000)]
net: allow setting env enetaddr from net device setting
If the net driver has setup a valid ethernet address and an ethernet
address is not set in the environment already, then set the environment
variables from the net driver setting.
This enables pxe booting on boards which don't set ethaddr env variable.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Dinh Nguyen [Fri, 8 Jun 2012 05:26:52 +0000 (05:26 +0000)]
net/designware: Consecutive writes to the same register to be avoided
This commit is an add-on to f6c4191f. There are a few registers where
consecutive writes to the same location should be avoided or have a delay.
According to Synopsys, here is a list of the registers and bit(s) where
consecutive writes should be avoided or a delay is required:
DMA Registers:
Register 0 Bit 7
Register 6 All bits except for 24, 16-13, 2-1.
GMAC Registers:
Registers 0-3 All bits
Registers 6-7 All bits
Register 10 All bits
Register 11 All bits except for 5-6.
Registers 16-47 All bits
Register 48 All bits except for 18-16, 14.
Register 448 Bit 4.
Register 459 Bits 0-3.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com> Reviewed-by: Matthew Gerlach <mgerlach@altera.com> Acked-by: Amit Virdi <amit.virdi@st.com>
Troy Kisky [Thu, 28 Jun 2012 08:00:28 +0000 (08:00 +0000)]
net: phy: micrel: make ksz9021 phy accessible
Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Timur Tabi [Mon, 9 Jul 2012 08:52:43 +0000 (08:52 +0000)]
net: abort network initialization if the PHY driver fails
Now that phy_startup() can return an actual error code, check for that error
code and abort network initialization if the PHY fails.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part) Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac) Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
The block argument for store_block can be -1 when the tftp sequence
number rolls over (i.e TftpBlock == 0), so the first argument to
store_block has to be of type 'int' instead of 'unsigned'.
In our environment (gcc 4.4.5 mips toolchain), this causes incorrect
'offset' to be generated for storing the block, and the tftp block
with number 0 will be written elsewhere, resulting in a bad block in
the downloaded file and a memory corruption.
Large EEPROMs, e.g. 24lc32, need 2 byte to address the internal memory.
These devices require that the high byte of the internal address has to be
written first.
The mxs_i2c driver currently writes the address' low byte first.
The following patch fixes the byte order of the internal address that should
be written to the I2C device.
Other then being very weird, this code was also wrong.
For example, say I set speed to 100K. I'll read back the speed
as 85937. But the speed is really 85937.5, so we I reset
the speed to 85937, I'll get 73660.7. After a couple of transactions
my speed is now exactly 68750 so it will remain there.
Wolfgang Denk [Mon, 9 Jul 2012 21:59:00 +0000 (23:59 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
* 'master' of git://git.denx.de/u-boot-usb:
CONFIG: EXYNOS5: USB: Enable USB 2.0 on smdk5250
EXYNOS5: USB: Fix incorrect USB base addresses
EXYNOS: Add power Enable/Disable for USB-EHCI
USB: EXYNOS: Set USB 2.0 HOST Link mode
EXYNOS5: Add structure for PMU registers
EXYNOS5: Fix system register structure
USB: EXYNOS: Incorporate EHCI review comments
Stephen Warren [Wed, 13 Jun 2012 09:55:12 +0000 (09:55 +0000)]
tegra: define fdt_load/fdt_high variables
These variables act like loadaddr, but for a device tree image. Defining
them in the environment allows boot scripts to be identical on Tegra20 and
Tegra30, which have different memory base addresses, and hence need
different values for these variables.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Jim Lin [Sun, 24 Jun 2012 20:40:57 +0000 (20:40 +0000)]
tegra: usb: Fix device enumeration problem of USB1
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 12 Jun 2012 08:33:41 +0000 (08:33 +0000)]
tegra: trimslice: set up serial flash pinmux
When Trimslice is booted from serial flash, the boot ROM does this, so
U-Boot doesn't need to. However, booting from the SD slot for recovery
purposes, the boot ROM does not set up the pinmux for serial flash. Add
code to U-Boot to set this up, so that an SD-based recovery U-Boot image
can upgrade the U-Boot in serial flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 4 Jun 2012 10:59:23 +0000 (10:59 +0000)]
tegra: bootcmd: start USB only when needed
Instead of initializing USB as soon as bootcmd is executed, defer it
until the first boot device that (potentially in the case of network)
uses USB is scanned. This avoids initializing USB when booting from MMC,
so speeds that up.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 4 Jun 2012 10:59:22 +0000 (10:59 +0000)]
tegra: bootcmd enhancements
Place the list of searched boot devices, file-system types, boot file
locations/prefixes, and boot script names into variables. This allows
the user to override them directly (e.g. to change boot order, or select
the specific values they use) without having to edit the main bootcmd
and script_boot variables.
The default boot order is changed from USB, MMC, DHCP to MMC, USB, DHCP.
This speeds up the typical MMC boot case. People who want USB boot can
now edit variable boot_targets appropriately.
Also, reformat BOOTCMDS_COMMON to fit within 80 columns.
Potential future enhancements might be:
* Allow boards to specify which of bootcmd_mmc0/... should be defined,
based on the HW they contain.
* Allow boards to influence the order that the boot targets are added
into the boot_targets variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 4 Jun 2012 09:23:55 +0000 (09:23 +0000)]
tegra: add enterrcm command
Tegra's boot ROM supports a mode whereby code may be downloaded and flash
programmed over a USB connection. On dev boards, this is typically entered
by holding down a "force recovery" button and resetting the CPU. However,
not all boards have such a button (one example is the Compulab Trimslice),
so a method to enter RCM from software is useful.
This change implements the command "enterrcm" to do this, and enables it
for all Tegra boards by default. Even on boards other than Trimslice,
controlling this over a UART may be useful, e.g. to allow simple remote
control without the need for mechanical button actuators, or hooking up
relays/... to the button.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 22 May 2012 09:21:54 +0000 (09:21 +0000)]
Add env vars describing U-Boot target board
This can be useful for generic scripts. For example, rather than hard-
coding a script to ext2load tegra-harmony.dtb, it could load
${soc}-${board}.dtb and hence not need adjustments to run on multiple
boards.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Thu, 31 May 2012 01:51:02 +0000 (01:51 +0000)]
tegra: usb: fix wrong error check
loop_count runs down from 10000, so the correct condition to error out
is ==0.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren.nvidia@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Lucas Stach [Thu, 31 May 2012 01:51:01 +0000 (01:51 +0000)]
tegra: add ULPI on USB2 funcmux entry
This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Thierry Reding [Mon, 4 Jun 2012 20:02:28 +0000 (20:02 +0000)]
tegra: Implement gpio_early_init() on Tamonten
The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Mon, 4 Jun 2012 20:02:24 +0000 (20:02 +0000)]
tegra: Rework Tamonten support
This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch corrects the SYSREG structure.
We have removed the sysreg.h added in the previous patchset
version as the sysreg structure is already defined in system.h.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Wolfgang Denk [Mon, 9 Jul 2012 07:19:00 +0000 (09:19 +0200)]
Revert "arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0"
This reverts commit fa042186b932e9b9ee9a2fd8a04a3acf7c70d224.
It causes build warnings like this:
cpu.c:48:1: warning: -fstack-usage not supported for this target
[enabled by default]
Stephen Warren [Fri, 8 Jun 2012 12:28:17 +0000 (12:28 +0000)]
fdt: send all dtc output to stderr
Commit 896bbb5 "fdt: avoid bad MAKEALL status" added logic to capture
the result code from dtc by echoing $? to stdout and capturing it using
$(). However, dtc emits some diagnostics to stderr and some to stdout.
The diagnostics send to stdout ended up getting captured via $() rather
than being echo'd to the user. This caused those diagnostics to be passed
to the exit command, which would then fail with the following cryptic
error message:
/bin/sh: line 1: exit: too many arguments
Solve this by redirecting all dtc output to stderr so that $() does not
capture it. This allows the user to see the actual error message from dtc.
Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: albert.u.boot@aribaud.net Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Kim Phillips [Tue, 3 Jul 2012 22:41:56 +0000 (17:41 -0500)]
ext2fs: fix warning: 'blocknxt' may be used uninitialized
This warning was introduced in 436da3c "ext2load: increase read
speed":
ext2fs.c: In function 'ext2fs_read_file':
ext2fs.c:458:19: warning: 'blocknxt' may be used uninitialized in this function [-Wuninitialized]
this change makes it go away.
Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Thierry Reding <thierry.reding@avionic-design.de> Cc: Jason Cooper <u-boot@lakedaemon.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Thu, 5 Jul 2012 13:19:32 +0000 (13:19 +0000)]
net: make net_rand.h inclusion depend on BOOTP_RANDOM_DELAY
commit "net: use common rand()/srand() functions" introduced the following
build warning on the current u-boot-arm tree:
$ ./MAKEALL MPC8313ERDB_66
Configuring for MPC8313ERDB_66 - Board: MPC8313ERDB, Options: SYS_66MHZ
text data bss dec hex filename
271988 13976 41768 327732 50034 ./u-boot
In file included from bootp.c:15:0:
net_rand.h: In function 'srand_mac':
net_rand.h:40:2: warning: implicit declaration of function 'srand' [-Wimplicit-function-declaration]
adding this dependency fixes it.
Cc: Michael Walle <michael@walle.cc> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Michael Walle <michael@walle.cc>
Wolfgang Denk [Sun, 8 Jul 2012 17:26:33 +0000 (19:26 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Wolfgang Denk [Sun, 8 Jul 2012 17:16:14 +0000 (19:16 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
SRICHARAN R [Wed, 16 May 2012 23:52:54 +0000 (23:52 +0000)]
ARM: cache: Move the cp15 CR register read before flushing the cache.
The following is the cleanup sequence in arch/arm/cpu/armv7/cpu.c
int cleanup_before_linux(void)
{
...
...
dcache_disable();
v7_outer_cache_disable();
invalidate_dcache_all();
}
1) invalidate_dcache_all call expects that all the caches has been
flushed, invalidated and there are no dirty entries prior to its
execution. In the above sequence dcache_disable() flushes, invalidates
the caches and turns off the mmu. But after it cleanups the cache
and before the mmu is disabled there is a cp_delay() function which
has STR instruction. On certain cores like the cortex-a15, cache hit
and a write can happen to a cache line even when the dcache is
disabled. So the above mentioned STR instruction creates a dirty entry
after cleaning. The mmu gets disabled after this.
2) invalidate_dcache_all invalidates the cache lines. Again on
cores like cortex-a15, invalidate instruction flushes the dirty
line as well. So some times the dirty line from sequence 1
can corrupt the memory resulting in a crash.
Fixing this by moving the get_cr() and cp_delay() calls before
cleaning up the cache, thus avoiding the dirty entry.
Stefan Roese [Fri, 20 Jan 2012 10:47:47 +0000 (11:47 +0100)]
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
Add support for the M41T82 RTC to the m41t62 driver. The only
difference that needs to be handled by this driver, is to
clear the HT (Halt Update) bit upon reset. This bit is not
used on the M41T62, so its save to clear this bit always.
The M41T82 support will be used by the X600 (SPEAr600)
board support.
Stefan Roese [Tue, 3 Jan 2012 15:49:01 +0000 (16:49 +0100)]
SPL: ARM: spear: Add SPL support for SPEAr600 platform
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com>
Stefan Roese [Thu, 5 Jan 2012 10:19:50 +0000 (11:19 +0100)]
Makefile: Add u-boot.spr build target (SPEAr)
On x600 (SPEAr600) U-Boot is appended to U-Boot SPL. Both images are
created using mkimage (crc etc), so that the ROM bootloader can check
its integrity. Padding needs to be done to the SPL image (with
mkimage header) and not the binary. Otherwise the resulting image
which is loaded/copied by the ROM bootloader to SRAM doesn't fit.
The resulting image containing both U-Boot images is called u-boot.spr.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com>
Stefan Roese [Mon, 7 May 2012 10:04:25 +0000 (12:04 +0200)]
net: Multiple updates/enhancements to designware.c
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
Amit Virdi [Mon, 7 May 2012 07:37:02 +0000 (13:07 +0530)]
cleanup/SPEAr: Define configuration flags more elegantly
In SPEAr, some of the configuration flags eg. CONFIG_SPEAR_EMI, were given value
"1", which isn't required. Define the flags without assigning any value
Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Amit Virdi [Mon, 7 May 2012 07:36:58 +0000 (13:06 +0530)]
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
When CONFIG_MTD_NAND_VERIFY_WRITE is defined, nand driver read back the data
everytime it writes. This process unnecessarily slows down the nand access.
Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Vipin Kumar [Mon, 7 May 2012 07:36:55 +0000 (13:06 +0530)]
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
The below text is copy pasted from README
- CONFIG_SYS_MONITOR_BASE:
Physical start address of boot monitor code (set by
make config files to be same as the text base address
(TEXT_BASE) used when linking) - same as
CONFIG_SYS_FLASH_BASE when booting from flash.
This patch corrects the definition of CONFIG_SYS_MONITOR_BASE and sets it to
TEXT_BASE
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
Vipin Kumar [Mon, 7 May 2012 07:36:54 +0000 (13:06 +0530)]
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
This patch enables flash protection(lock/unlock) for CFI devices.
This is necessary because the Parallel NOR flash connected on the spear
boards, M28W64, can be locked/unlocked on a sector basis. Moreover, all its
sectors are in locked state at reset and these have to be unlocked explicitly
before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Shiraz Hashim [Mon, 7 May 2012 07:36:53 +0000 (13:06 +0530)]
SPEAr: Enable dcache for fast file transfer
Enable data cache with 1:1 mapping of DDR to enable fast file
transfer over tty which was doing lot of copy.
This feature is enabled only for flashing operation i.e. when
CONFIG_SPEAR_USBTTY is enabled.
This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation
boards.
Following figures show an estimate on the performance improvements. The
test setup was a Linux host (not Windows) and involved measurement of
only binary transfer time, through kermit. The flash erase and flash
copy time would be unaffected by these patches.
Another thing is this that the timings remained more or less same across
ARM9 and Cortex based devices, hence reporting only one of the cases.
Before Enhancements
===================
$ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m41.228s
user 0m0.002s
sys 0m0.064s
After Enhancements
==================
$ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m5.441s
user 0m0.001s
sys 0m0.001s
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
Shiraz Hashim [Mon, 7 May 2012 07:36:52 +0000 (13:06 +0530)]
SPEAr: Enable autoneg for ethernet
Enabling autoneg avoids situation on few phys with fixed configuration. For
example, in one situation, nfs boot timed out when phy configuration is 100Mbps.
In another situtation, when traffic is directed to SPEAr, either thru
cross-cable or thru switch, the TFTP or DHCP command in u-boot starts to timeout
very often.
When Autoneg is ON, same phys started working perfectly.
Reported-by: Deepak Sikri <deepak.sikri@st.com> Reported-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
Amit Virdi [Mon, 7 May 2012 07:36:49 +0000 (13:06 +0530)]
SPEAr: Initialize SNOR in early_board_init_f
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Vipin KUMAR [Mon, 7 May 2012 07:36:48 +0000 (13:06 +0530)]
SPEAr: Change the default environment variables
This patch modifies the default environment variables as:
1. Default bootargs:
- console=ttyAMA0,115200
- For environment present in NOR flash
root=/dev/mtdblock3
- For environment present in NAND flash
root=/dev/mtdblock7
- Removes "mem=" option
2. Introduces CONFIG_EXTRA_ENV_USBTTY as default usbtty env var even when usbtty
is not selected
3. Add default definitions for nfsboot and ramboot
4. Add a new default environment variable(CONFIG_EXTRA_ENV_UNLOCK) for SPEAr310
and SPEAr320
Signifacance of CONFIG_EXTRA_ENV_USBTTY:
This environment variable is important for flashing utility to work. So if
somebody accidently erases the env sector then also this variable must be
preserved so that flashing utility functions properly.
Signifacance of CONFIG_EXTRA_ENV_UNLOCK:
This env variable is read by the cfi driver to unlock all flash sectors. This
is necessary because the Parallel NOR flash connected on the spear310 and
spear320 boards, M28W64, has all its sectors in locked state at reset and these
have to be unlocked explicitly before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log