Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Sat, 16 Feb 2019 02:21:28 +0000 (21:21 -0500)]
Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tim Harvey [Mon, 4 Feb 2019 21:11:00 +0000 (13:11 -0800)]
imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+)
device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit 8dccafaa281aa1d240a58bbcdff338aec114a021.
This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
- enabling MMC UHS-I on board revisions that support it
- enabling PWM based on hwconfig
- fixing PCIe reset on GW552x
- removing cpu external watchdog reset on boards that do not support it
- populate PCI dt nodes based on PCI scan in order to fix GW16082
interrupt mapping and inject MAC address for PCI based GbE
Tim Harvey [Mon, 4 Feb 2019 21:10:57 +0000 (13:10 -0800)]
imx: ventana: add support for GW5909
The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Tim Harvey [Mon, 4 Feb 2019 21:10:56 +0000 (13:10 -0800)]
imx: ventana: add support for GW5908
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Tim Harvey [Mon, 4 Feb 2019 21:10:55 +0000 (13:10 -0800)]
imx: ventana: add support for GW5907
The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
- DDR3 memory (512MB default)
- 1x GigE (i.MX6 FEC)
- Gateworks System Controller
Tim Harvey [Mon, 4 Feb 2019 21:10:50 +0000 (13:10 -0800)]
imx: ventana: add support for GW5905
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
- eMMC flash (boot device)
- microSD expansion
- LVDS display connector for off-board 3D+1C with PWM backlight
and I2C based touch controller
- MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
- ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
- ublox ZOE-M8Q GPS
- LSM9DS1 9-DOF IMU
- 1x 1-lane miniPCIe socket with USB 2.0
- Gateworks System Controller
- Audio jack with TLV320AIC Audio Codec, Speaker AMP
and TSA227E Headphone detect
- MAX8607 3-mode LED camera flash
- DECT ULE module
- FUSB302 USB-C PD and ISL9238 Battery charger
Tim Harvey [Mon, 4 Feb 2019 21:10:49 +0000 (13:10 -0800)]
imx: ventana: remove setup of I2C3 from SPL
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Abel Vesa [Fri, 1 Feb 2019 16:40:25 +0000 (16:40 +0000)]
configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI support
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:14 +0000 (16:40 +0000)]
arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] files
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:07 +0000 (16:40 +0000)]
usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
Michal Simek [Thu, 14 Feb 2019 12:14:30 +0000 (13:14 +0100)]
arm64: zynqmp: Create fdtfile from compatible string
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
Amit Kucheria [Thu, 23 Aug 2018 08:53:29 +0000 (14:23 +0530)]
arm64: dts: Fix various entry-method properties to reflect documentation
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Add reset-on-timeout for all boards and modify default timeout value
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:20 +0000 (00:10 -0400)]
ARM: dts: zynq: correct and improve the model property of dt files
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tim Harvey [Mon, 4 Feb 2019 20:56:52 +0000 (12:56 -0800)]
net: mv88e61xx: fix autonegotiation on ports
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 non-SPL targets
Add HABv4 documentation for non-SPL targets covering the
following topics:
- How to sign an securely boot an u-boot-dtb.imx image.
- How to extend the root of trust for additional boot images.
- Add 3 CSF examples.
- Add IVT generation script example.
Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com> Signed-off-by: Breno Lima <breno.lima@nxp.com>
Adam Ford [Thu, 17 Jan 2019 13:16:39 +0000 (07:16 -0600)]
MTD: nand: mxs_nand: Allow driver to auto setup ECC in SPL
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Jörg Krause <joerg.krause@embedded.rocks> Acked-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Tim Harvey <tharvey@gateworks.com>
Adam Ford [Tue, 15 Jan 2019 17:26:48 +0000 (11:26 -0600)]
net: dm: fec: Fix regulator enable when using DM_REGULATOR
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbcafb ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Sat, 12 Jan 2019 23:32:00 +0000 (17:32 -0600)]
ARM: imx6q_logic: Correct phy fixup for broken ethernet
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Tested-by: Jörg Krause <joerg.krause@embedded.rocks> Acked-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Tim Harvey <tharvey@gateworks.com>
Michal Simek [Wed, 13 Feb 2019 12:33:32 +0000 (13:33 +0100)]
arm64: zynqmp: Remove board config files
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 12:46:41 +0000 (13:46 +0100)]
arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCI
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 18 Jan 2019 08:10:39 +0000 (09:10 +0100)]
arm64: zynqmp: Switch all platforms to DM_I2C
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 13:43:04 +0000 (14:43 +0100)]
ARM: zynq: Convert dlc20 and zc70x board to DM_I2C
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 13:12:54 +0000 (14:12 +0100)]
ARM: zynq: Convert Syzygy to DM_I2C
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: versal: Define distro boot commnads for qspi ospi and mmc
This patch adds distro boot commands for qspi, ospi and mmc.
The distro boot commands now reads the script from flash offset
of 63.5MB for qspi and ospi and executes it. For mmc its same
as generic distro boot command. As either one of the qspi or ospi can
exist on hardware, defined a single distroboot command as xspi
that works for both.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards for qspi, ospi for now.
512kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm: zynq: Define distro boot commnads for qspi, nand and nor
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 21 Jan 2019 15:29:07 +0000 (16:29 +0100)]
xilinx: common: Add support for DM_I2C zynq_board_read_rom_ethaddr()
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
Michal Simek [Mon, 21 Jan 2019 14:25:02 +0000 (15:25 +0100)]
xilinx: Move zynq_board_read_rom_ethaddr to shared location
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Define distro boot commnads for qspi and nand
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 3 Jan 2019 12:58:27 +0000 (13:58 +0100)]
ARM: zynq: Run distribution boot commands first
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 13 Feb 2019 12:12:29 +0000 (07:12 -0500)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2019-02-13
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
We check the existence of files with fs_exist(). This function calls
fs_close(). If we do not set the active block device again fs_opendir()
fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the
`cd` command in the EFI shell fails.
So let's add the missing set_blk_dev(fh) call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
projects / u-boot.git / log