Kconfig: FIT_SIGNATURE should not select RSA_VERIFY
FIT signatures can now be implemented with ECDSA. The assumption that
all FIT images are signed with RSA is no longer valid. Thus, instead
of 'select'ing RSA, only 'imply' it. This doesn't change the defaults,
but allows one to explicitly disable RSA support.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
lib: ecdsa: Implement UCLASS_ECDSA verification on target
Implement the crypto_algo .verify() function for ecdsa256. Because
it backends on UCLASS_ECDSA, this change is focused on parsing the
keys from devicetree and passing this information to the specific
UCLASS driver.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
dm: crypto: Define UCLASS API for ECDSA signature verification
Define a UCLASS API for verifying ECDSA signatures. Unlike
UCLASS_MOD_EXP, which focuses strictly on modular exponentiation,
the ECDSA class focuses on verification. This is done so that it
better aligns with mach-specific implementations, such as stm32mp.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Mon, 9 Aug 2021 12:06:04 +0000 (14:06 +0200)]
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex for SPL, so opt for the second option. This incurs 20ms delay
during boot, when SPL loads U-Boot to DRAM.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 27 Jul 2021 10:15:12 +0000 (12:15 +0200)]
arm: dts: stm32mp15: alignment with v5.14
Device tree alignment with Linux kernel v5.14-rc3
- ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15
- ARM: dts: stm32: Configure qspi's mdma transfer to block for stm32mp151
- ARM: dts: stm32: add a new DCMI pins group on stm32mp15
- ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The function board_get_usable_ram_top can be called after relocation
with total_size = 0 to get the uppermost pointer that is valid to access
in U-Boot.
When total_size = 0, the reserved memory should be not take in account
with lmb library and 'gd->ram_base + gd->ram_size' can be used.
It is the case today in lib/efi_loader/efi_memory.c:efi_add_known_memory()
and this patch avoids that the reserved memory for OP-TEE is not part of
the EFI available memory regions.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 26 Jul 2021 09:21:38 +0000 (11:21 +0200)]
stm32mp1: stm32prog: remove stm32prog_get_tee_partitions with FIP
The MTD tee partitions used to save the OP-TEE binary are needed when
TF-A doesn't use the FIP container to load binaries.
This patch puts under CONFIG_STM32MP15x_STM32IMAGE flag the associated
code in U-Boot binary and prepare the code cleanup when
CONFIG_STM32MP15x_STM32IMAGE support will be removed after TF-A migration
to FIP support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 26 Jul 2021 09:21:36 +0000 (11:21 +0200)]
arm: stm32mp: add defconfig for trusted boot with FIP
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.
With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.
With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 26 Jul 2021 09:21:35 +0000 (11:21 +0200)]
arm: stm32mp: handle the OP-TEE nodes in DT with FIP support
With FIP support in TF-A (when CONFIG_STM32MP15x_STM32IMAGE
is not activated), the DT nodes needed by OP-TEE are added by OP-TEE
firmware in U-Boot device tree, present in FIP.
These nodes are only required in trusted boot, when TF-A load the file
u-boot.stm32, including the U-Boot device tree with STM32IMAGE header,
in this case OP-TEE can't update the U-Boot device tree.
Moreover in trusted boot mode with FIP, as the OP-TEE nodes are present
in U-Boot device tree only when needed the function
stm32_fdt_disable_optee can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 26 Jul 2021 09:21:34 +0000 (11:21 +0200)]
arm: stm32mp: add config for STM32IMAGE support
By default for trusted boot with TF-A, U-Boot (u-boot-nodtb)
is located in FIP container with its device tree and with
the secure monitor (provided by TF-A or OP-TEE).
The FIP file is loaded by TF-A BL2 and each components is
extracted at the final location.
This patch add CONFIG_STM32MP15x_STM32IMAGE to request the
STM32 image generation for SOC STM32MP15x
when FIP container is not used (u-boot.stm32 is loaded by TF-A
as done previously to keep the backward compatibility).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Fri, 16 Jul 2021 08:10:55 +0000 (10:10 +0200)]
clk: stm32mp1: add support of BSEC clock
Add the support of the BSEC clock used by the STM32MP misc driver
since the commit 622c956cada0 ("stm32mp: bsec: manage clock when present
in device tree") even if this clock is not yet defined in kernel device
tree stm32mp151.dtsi.
This patch avoids issue for basic boot when this secure clock are not
provided by secure world with SCMI.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tom Rini [Sun, 15 Aug 2021 17:42:42 +0000 (13:42 -0400)]
Merge tag 'efi-2021-10-rc2-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc2-2
Documentation:
* Require Sphinx >= 2.4.4 for 'make htmldocs'
* Move devicetree documentation to restructured text and update it
* Document stm32mp1 devicetree bindings
UEFI
* Extend measurement to UEFI variables and ExitBootServices()
* Support Uri() node in devicetree to text protocol
* Add Linux magic token to RISC-V EFI test binaries
Masahisa Kojima [Fri, 13 Aug 2021 07:12:41 +0000 (16:12 +0900)]
efi_loader: add ExitBootServices() measurement
TCG PC Client PFP spec requires to measure
"Exit Boot Services Invocation" if ExitBootServices() is invoked.
Depending upon the return code from the ExitBootServices() call,
"Exit Boot Services Returned with Success" or "Exit Boot Services
Returned with Failure" is also measured.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Swap two ifs in efi_exit_boot_services().
efi_tcg2_notify_exit_boot_services must have EFIAPI signature. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Masahisa Kojima [Fri, 13 Aug 2021 07:12:40 +0000 (16:12 +0900)]
efi_loader: add boot variable measurement
TCG PC Client PFP spec requires to measure "Boot####"
and "BootOrder" variables, EV_SEPARATOR event prior
to the Ready to Boot invocation.
Since u-boot does not implement Ready to Boot event,
these measurements are performed when efi_start_image() is called.
TCG spec also requires to measure "Calling EFI Application from
Boot Option" for each boot attempt, and "Returning from EFI
Application from Boot Option" if a boot device returns control
back to the Boot Manager.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Masahisa Kojima [Fri, 13 Aug 2021 07:12:39 +0000 (16:12 +0900)]
efi_loader: add secure boot variable measurement
TCG PC Client PFP spec requires to measure the secure
boot policy before validating the UEFI image.
This commit adds the secure boot variable measurement
of "SecureBoot", "PK", "KEK", "db", "dbx", "dbt", and "dbr".
Note that this implementation assumes that secure boot
variables are pre-configured and not be set/updated in runtime.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Add the Linux magic to the EFI file header to allow running our test
programs with GRUB's linux command.
MajorImageVersion = 1 indicates a kernel that can consume the
EFI_LOAD_FILE2_PROTOCOL. This allows to dump the GRUB provided intird with
our initrddump.efi tool.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.
Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add links for referenced text files. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Mon, 2 Aug 2021 00:57:11 +0000 (18:57 -0600)]
doc: Update devicedocs including how to add tweaks
This file is about 10 years old and the updates have not covered
everything that has changed, particularly in the last few years. Update
the information and add mention of the u-boot.dtsi files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix typos. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Jon Lin [Thu, 5 Aug 2021 08:27:53 +0000 (16:27 +0800)]
rockchip: px30: Support configure SFC
Make px30 SFC clock configurable
Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:27:52 +0000 (16:27 +0800)]
rockchip: px30: add support for SFC for Odroid Go Advance
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:41 +0000 (16:26 +0800)]
mtd: spi-nor-ids: Add XTX XT25F128B
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:40 +0000 (16:26 +0800)]
rockchip: px30: add the serial flash controller
Add the serial flash controller to the devicetree for the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:39 +0000 (16:26 +0800)]
rockchip: px30: Add support for using SFC
This patch adds support for setting the correct pin configuration
for the Rockchip Serial Flash Controller found on the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:38 +0000 (16:26 +0800)]
spi: rockchip_sfc: add support for Rockchip SFC
This patch adds support for the Rockchip serial flash controller
found on the PX30 SoC. It should work for versions 3-5 of the SFC
IP, however I am only able to test it on v3.
This is adapted from the WIP SPI-MEM driver for the SFC on mainline
Linux. Note that the main difference between this and earlier versions
of the driver is that this one does not support DMA. In testing
the performance difference (performing a dual mode read on a 128Mb
chip) is negligible. DMA, if used, must also be disabled in SPL
mode when using A-TF anyway.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Gunnarsson [Sun, 25 Jul 2021 14:25:58 +0000 (16:25 +0200)]
rockchip: Fix u-boot-rockchip.bin build
Currently there are a few arm32 rockchip board configs that don't
generate u-boot-rockchip.bin when running make because CONFIG_BINMAN
is not enabled. This patch changes CONFIG_ARCH_ROCKCHIP to also select
CONFIG_BINMAN if CONFIG_SPL and !CONFIG_ARM64.
Example builds that don't generate u-boot-rockchip.bin without this
patch:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make kylin-rk3036_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make rock_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make tinker-rk3288_defconfig
make
Signed-off-by: Johan Gunnarsson <johan.gunnarsson@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
Tom Rini [Wed, 11 Aug 2021 12:31:13 +0000 (08:31 -0400)]
Merge tag 'u-boot-amlogic-20210810' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
Yifeng Zhao [Tue, 29 Jun 2021 08:24:41 +0000 (16:24 +0800)]
mmc: rockchip_sdhci: add phy and clock config for rk3399
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Johan Jonker [Fri, 25 Jun 2021 13:26:33 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3188-radxarock.dts
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 25 Jun 2021 13:26:32 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3188.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 25 Jun 2021 13:26:30 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3xxx.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Artem Lapkin [Wed, 26 May 2021 09:32:27 +0000 (17:32 +0800)]
rk3399: boot_devices fix spinor node name
Problem: board_spl_was_booted_from return wrong boot_devices[3] value
/spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash
because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device
need parse SPINOR flash node as UCLASS_SPI_FLASH
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device
/sdhci@fe330000 > /mmc@fe320000
Alex Bee [Thu, 17 Jun 2021 09:01:12 +0000 (11:01 +0200)]
rockchip: Fix MMC boot order
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <knaerzche@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Bin Meng [Sat, 7 Aug 2021 05:00:00 +0000 (13:00 +0800)]
mtd: kconfig: Fix CFI_FLASH dependency
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 9 Aug 2021 15:44:35 +0000 (17:44 +0200)]
arm: mvebu: Hang if ddr3_init() fails
If ddr3_init() fails then DDR was not initialized and we cannot load and
execute U-Boot. We cannot continue, we cannot do anything in this case, so
hang.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 9 Aug 2021 07:53:13 +0000 (09:53 +0200)]
arm: a37xx: pci: Fix handling PIO config error responses
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Sun, 1 Aug 2021 03:29:35 +0000 (20:29 -0700)]
arm: mvebu: sata_mv failed to identify HDDs during cold start
During cold start, with some HDDs, mv_sata_identify() does not populate
the ID words on the 1st ATA ID command. In fact, the first ATA ID
command will only power up the drive, and then the ATA ID command
processing is lost in the process.
- The Seagate ST9250320AS 250GB took about 3 seconds to spin up.
- The Seagate ST4000DM004-2CV104 4TB took about 8 seconds to spin up.
- mv_sata_identify() did not populate the ID words after the call to
mv_ata_exec_ata_cmd_nondma().
- Attempt to insert a long delay of 30 seconds, ie. mdelay(30_000), after
the call to ata_wait_register() inside mv_ata_exec_ata_cmd_nondma() did
not help with the 4TB drive. The ID words were still empty after that 30s
delay.
Patch Description:
- Added a second ATA ID command in mv_sata_identify(), which will be
executed if the 1st ATA ID command did not return with valid ID words.
- Use the HDD drive capacity in the ID words as a successful indicator of
ATA ID command.
- In the scenario where a box is rebooted, the 1st ATA ID command is always
successful, so there is no extra time wasted.
- In the scenario where a box is cold started, the 1st ATA command is the
power up command. The 2nd ATA ID command alleviates the uncertainty of
how long we have to wait for the ID words to be populated by the SATA
controller.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Fri, 30 Jul 2021 03:02:43 +0000 (20:02 -0700)]
arm: kirkwood: GoFlex Home: Use Ethernet PHY name and address from device tree
In DM Ethernet, the old "egiga0" name is no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
configs: sei510/610: android bootflow via abootimg
Activate the following Kconfig options:
* AVB for Android Verified Boot support
* ADTIMG for merging DTBOs
* ABOOTIMG for extracting Android boot image
Also rework the partitioning tables:
- add a misc partition to handle BCB messages
- add a dtbo partition to store various DTBOs
- add a vbmeta partition for AVB hashes
- Merge vendor and system into the "super" partition
Note: avb support is disables by default. To activate it:
=> setenv force_avb 1;
=> saveenv;
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
configs: sei510/sei610: don't use hard-coded gpt uuids
doc/README.gpt states:
> The fields 'uuid' and 'uuid_disk' are optional if CONFIG_RANDOM_UUID is
> enabled. A random uuid will be used if omitted or they point to an empty/
> non-existent environment variable. The environment variable will be
> set to the generated UUID. The 'gpt guid' command reads the current
> value of the uuid_disk from the GPT.
Since we have CONFIG_RANDOM_UUID=y, remove the hard-coded uuids
and use meaningful variable names instead.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
configs: meson64_android: boot android via abootimg
Since Android 10, we are required to use a "dtbo" partition which
includes the various device-tree overlays [1].
It's also possible to provide a "dtb" partition.
This is supported via the "abootimg" command.
On Yukawa, the assumption is that we have only a "dtbo" partition, which
includes all board dtbs and their dtbos [2]
[1] https://source.android.com/devices/architecture/dto/partitions
[2] https://android.googlesource.com/device/amlogic/yukawa/+/refs/heads/master/build/tasks/dtimages.mk#16 Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
configs: meson64_android: increase SYS_MALLOC_LEN to 128M for AVB
To prepare for AVB support, increase SYS_MALLOC_LEN to 128M.
This value has been found by testing the following on khadas vim3l:
=> avb init
=> avb verify
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
board: amlogic: odroid-n2: fix fdtfile suffix for n2-plus
The N2+ dtb is meson-g12b-odroid-n2-plus.dtb, not n2_plus, so
correct the suffix provided in the board file. Also align the
board ident string shown during boot to match.
Fixes: 8bc780106c13 ("board: amlogic: odroid: add runtime detection of the N2/N2+/C4/HC4 variants") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- new SOC: add support for imx8ulp
- Toradex fixes for colibri (vf / imx6 / imx7 / imx8x)
- convert to DM for mx28evk
- Fixes for Gateworks ventana boards
Peng Fan [Sat, 7 Aug 2021 08:01:13 +0000 (16:01 +0800)]
arm: imx: add i.MX8ULP EVK support
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Ye Li [Sat, 7 Aug 2021 08:01:07 +0000 (16:01 +0800)]
imx8ulp: Use DGO_GP5 to get boot config
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
projects / u-boot.git / log