Jon Lin [Thu, 5 Aug 2021 08:27:53 +0000 (16:27 +0800)]
rockchip: px30: Support configure SFC
Make px30 SFC clock configurable
Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:27:52 +0000 (16:27 +0800)]
rockchip: px30: add support for SFC for Odroid Go Advance
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:41 +0000 (16:26 +0800)]
mtd: spi-nor-ids: Add XTX XT25F128B
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:40 +0000 (16:26 +0800)]
rockchip: px30: add the serial flash controller
Add the serial flash controller to the devicetree for the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:39 +0000 (16:26 +0800)]
rockchip: px30: Add support for using SFC
This patch adds support for setting the correct pin configuration
for the Rockchip Serial Flash Controller found on the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 5 Aug 2021 08:26:38 +0000 (16:26 +0800)]
spi: rockchip_sfc: add support for Rockchip SFC
This patch adds support for the Rockchip serial flash controller
found on the PX30 SoC. It should work for versions 3-5 of the SFC
IP, however I am only able to test it on v3.
This is adapted from the WIP SPI-MEM driver for the SFC on mainline
Linux. Note that the main difference between this and earlier versions
of the driver is that this one does not support DMA. In testing
the performance difference (performing a dual mode read on a 128Mb
chip) is negligible. DMA, if used, must also be disabled in SPL
mode when using A-TF anyway.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Gunnarsson [Sun, 25 Jul 2021 14:25:58 +0000 (16:25 +0200)]
rockchip: Fix u-boot-rockchip.bin build
Currently there are a few arm32 rockchip board configs that don't
generate u-boot-rockchip.bin when running make because CONFIG_BINMAN
is not enabled. This patch changes CONFIG_ARCH_ROCKCHIP to also select
CONFIG_BINMAN if CONFIG_SPL and !CONFIG_ARM64.
Example builds that don't generate u-boot-rockchip.bin without this
patch:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make kylin-rk3036_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make rock_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make tinker-rk3288_defconfig
make
Signed-off-by: Johan Gunnarsson <johan.gunnarsson@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Yifeng Zhao [Tue, 29 Jun 2021 08:24:41 +0000 (16:24 +0800)]
mmc: rockchip_sdhci: add phy and clock config for rk3399
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Johan Jonker [Fri, 25 Jun 2021 13:26:33 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3188-radxarock.dts
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 25 Jun 2021 13:26:32 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3188.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 25 Jun 2021 13:26:30 +0000 (15:26 +0200)]
ARM: dts: rockchip: update rk3xxx.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Artem Lapkin [Wed, 26 May 2021 09:32:27 +0000 (17:32 +0800)]
rk3399: boot_devices fix spinor node name
Problem: board_spl_was_booted_from return wrong boot_devices[3] value
/spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash
because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device
need parse SPINOR flash node as UCLASS_SPI_FLASH
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device
/sdhci@fe330000 > /mmc@fe320000
Alex Bee [Thu, 17 Jun 2021 09:01:12 +0000 (11:01 +0200)]
rockchip: Fix MMC boot order
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <knaerzche@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- new SOC: add support for imx8ulp
- Toradex fixes for colibri (vf / imx6 / imx7 / imx8x)
- convert to DM for mx28evk
- Fixes for Gateworks ventana boards
Peng Fan [Sat, 7 Aug 2021 08:01:13 +0000 (16:01 +0800)]
arm: imx: add i.MX8ULP EVK support
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Ye Li [Sat, 7 Aug 2021 08:01:07 +0000 (16:01 +0800)]
imx8ulp: Use DGO_GP5 to get boot config
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Peng Fan [Sat, 7 Aug 2021 08:00:58 +0000 (16:00 +0800)]
arm: imx8ulp: release trdc and assign lpav from RTD to APD
Rlease LPAV from RTD to APD
Release gpu2D/3D to APD
Set TRDC MBC2 MEM1 for iomuxc0 access
Since upower depends AP/M33 SW to configure IOMUX for its PMIC i2c
and MODE pins. we have to open iomuxc0 access for A35 core (domain 7)
in single boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
Ye Li [Sat, 7 Aug 2021 08:00:55 +0000 (16:00 +0800)]
arm: imx8ulp: release and configure XRDC at early phase
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Sat, 7 Aug 2021 08:00:48 +0000 (16:00 +0800)]
arm: imx8ulp: Enable full L2 cache in SPL
SRAM2 is half L2 cache and default to SRAM after system boot.
To enable the full l2 cache (512KB), it needs to reset A35 to make
the change happen.
So re-implement the jump entry function in SPL:
1. configure the core0 reset vector to entry (ATF)
2. enable the L2 full cache
3. reset A35
So when core0 up, it runs into ATF. And we have 512KB L2 cache working.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Sat, 7 Aug 2021 08:00:35 +0000 (16:00 +0800)]
arm: imx: basic i.MX8ULP support
Add basic i.MX8ULP support
For the MMU part, Using a simple way the calculate the MMU size to avoid
default heavy calcaulation. And align address and size in the table
settings to 2MB or 4GB as much as possible. So we can reduce the 4K page
allocations in MMU table which will spends much time in create the
page table
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Select CONFIG_IMX_HAB so that the "hab_status" command
becomes available, which is useful for checking if the
chip has been correctly setup to run in secure boot mode.
Tim Harvey [Tue, 27 Jul 2021 22:19:41 +0000 (15:19 -0700)]
board: gateworks: venice: add imx8mm-gw7902 support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Tim Harvey [Tue, 27 Jul 2021 22:19:39 +0000 (15:19 -0700)]
board: gateworks: venice: add board model/serial# to env
Add board model/serial# strings to env. Move the creation of the strings
to gsc_read() and the display of the info into gsc_info() so they are
available to U-Boot proper.
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.
Tim Harvey [Tue, 27 Jul 2021 22:19:34 +0000 (15:19 -0700)]
arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
The intention of commit d714a75fd4dc ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.
Fix it by using the correct CONFIG_IMX_HAB symbol.
Tim Harvey [Sat, 24 Jul 2021 17:40:46 +0000 (10:40 -0700)]
imx: ventana: add support for GW54xx-G revision
The GW54xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Tim Harvey [Sat, 24 Jul 2021 17:40:45 +0000 (10:40 -0700)]
imx: ventana: add support for GW53xx-G revision
The GW53xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Tim Harvey [Sat, 24 Jul 2021 17:40:44 +0000 (10:40 -0700)]
imx: ventana: add GW5913 support
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- Digital I/O connector (I2C/GPIO/UART)
- u-blox Zoe-M8Q GPS
- 1x RJ45 GbE
- 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:43 +0000 (10:40 -0700)]
imx: ventana: add GW5912 support
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- CAN/RS485 connector
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- 1x FEC GbE RJ45 with 802.3at Active PoE
- 1x PCI GbE RJ45 with Passive PoE
- 5x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
- Aux power input with wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:42 +0000 (10:40 -0700)]
imx: ventana: add GW5910 support
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
- On-board brcmfmac WiFi and BT module
- RGMII RJ45 GbE
- 1x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:36 +0000 (10:40 -0700)]
imx: ventana: fix UMS support
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.
U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.
Fixes 72c46327f03f: ("imx: ventana: enable dm support for USB")
projects / u-boot.git / log