Laurentiu Tudor [Thu, 9 Aug 2018 12:19:44 +0000 (15:19 +0300)]
misc: fsl_portals: setup QMAN_BAR{E} also on ARM platforms
QMAN_BAR{E} register setup was disabled on ARM platforms, however the
register does need to be set. Enable the code also on ARMs and fix the
CONFIG_SYS_QMAN_MEM_PHYS define to the correct value so that the newly
enabled code works.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Most FSL PCIe controllers expects 333 MHz PCI reference clock.
This clock is derived from the CCB but in many cases the ref.
clock is not 333 MHz and a divisor needs to be configured.
This adds PEX_CCB_DIV #define which can be defined for each
type of CPU/platform.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Reviewed-by: York Sun <york.sun@nxp.com>
In ft_fixup_enet_phy_connect_type(), use strlen() instead of sizeof()
on the pointer result of phy_string_for_interface(). sizeof() was
returning the size of the pointer (4 bytes), resulting in the
phy-connection-type being set to "rgmi" rather than "rgmii-id".
Signed-off-by: Brendan Shanks <brendan.shanks@teradek.com> Cc: York Sun <york.sun@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Fri, 27 Jul 2018 02:20:39 +0000 (10:20 +0800)]
dm: power-domain: query power domain after get device
This is to test power_domain_on in device_probe.
If the device has a power-domain property, enable it
when probe the device. So add the test to check
whether it is powered on or not.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Neil Armstrong [Thu, 26 Jul 2018 13:19:32 +0000 (15:19 +0200)]
clk: clk_set_default: accept no-op skip fields
The Assigned Clock parents and rates misses the fact that a "0" entry can
be passed to skip setting a parent or rate of an assigned clock as
described in the Linux clock bindings at [1].
This patch simply skips the clock reparenting if the DT parsing returns
-ENOENT and the clock rate setting if "0" is passed as clock rate.
mmc: arm_pl180_mmci: Remove cd_inverted host's struct field
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Andre Przywara [Tue, 24 Jul 2018 23:57:01 +0000 (00:57 +0100)]
armv8: make SPL exception vectors optional
Even though the exception vector table is a fundamental part of the ARM
architecture, U-Boot mostly does not make real use of it, except when
crash dumping. But having it in takes up quite some space, partly due to
the architectural alignment requirement of 2KB. Since we don't take special
care of that, the compiler adds a more or less random amount of padding
space, which increases the image size quite a bit, especially for the SPL.
On a typical Allwinner build this is around 1.5KB of padding, plus 1KB
for the vector table (mostly padding space again), then some extra code
to do the actual handling. This amounts to almost 10% of the maximum image
size, which is quite a lot for a pure debugging feature.
Add a Kconfig symbol to allow the exception vector table to be left out
of the build for the SPL.
For now this is "default y" for everyone, but specific defconfigs,
platforms or .config files can opt out here at will, to mitigate the code
size pressure we see for some SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 24 Jul 2018 23:57:00 +0000 (00:57 +0100)]
armv8: Reduce exception handling code
The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.
Let's consoldate this all into one place, and remove them from the
individual boards.
This patch adds support for STMicroelectronics STM32 ADC (analog to
digital converter). It's originally based on Linux kernel v4.18-rcs
drivers/iio/adc/stm32-adc*. It's composed of:
- core driver (UCLASS_SIMPLE_BUS) manages common resources (clk, regu).
- child drivers (UCLASS_ADC) declare each ADC, channels and handle
conversions.
This driver currently supports STM32H7 and STM32MP1 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds documentation of device tree bindings for the STM32 ADC.
It's based on linux-v4.18-rc* dt-bindings, at the time of writing:
- Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
device_get_supply_regulator() only needs to be called once.
But each time there's call to adc_vxx_value() for instance, it calls
adc_vxx_platdata_update() -> device_get_supply_regulator().
So, move device_get_supply_regulator() to pre_probe() routine.
This also allows vdd_supply/vss_supply to be provided directly from
uc_pdata, e.g dt-binding variant like stm32-adc provide its own
'vref-supply'.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Wed, 1 Aug 2018 06:49:26 +0000 (12:19 +0530)]
spi: kirkwood: add orion-spi compatible string
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Thu, 15 Mar 2018 11:33:22 +0000 (17:03 +0530)]
spi: kirkwood: Get drvdata in .ofdata_to_platdata
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Clément Laigle <c.laigle@catie.fr> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Stephen Warren [Tue, 31 Jul 2018 18:38:27 +0000 (12:38 -0600)]
ARM: tegra: align carveout size
Align the size of the carveout region to 2M. This ensures that the size
can be accurately represented by an LPAE page table that uses sections.
This solves a bug (hang at boot time soon after printing the DRAM size)
that only shows up when the following two commits are merged together: d32e86bde8a3 ARM: HYP/non-sec: enable ARMV7_LPAE if HYP mode is supported 6e584e633d10 ARM: tegra: avoid using secure carveout RAM
Cc: Mark Kettenis <kettenis@openbsd.org> Cc: Alexander Graf <agraf@suse.de> Acked-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Tue, 17 Jul 2018 19:25:52 +0000 (13:25 -0600)]
binman: Adjust _GetPropTree() parameters
At present this function takes a filename, but it is better to use an Fdt
object so that the caller can control this, perhaps obtainint the device
tree from a bytearray. Update the method accordingly and also fix a
confusing parameter name.
Simon Glass [Tue, 17 Jul 2018 19:25:49 +0000 (13:25 -0600)]
binman: Show the image position in the map
At present the map only shows the offset and size for each region. The
image position provides the actual position of each entry in the image,
regardless of the section hierarchy.
Simon Glass [Tue, 17 Jul 2018 19:25:46 +0000 (13:25 -0600)]
dtoc: Add a function to obtain a list of phandles
Add a function which can decode a property containing a list of phandles.
This is useful for finding nodes linked to a property. Also provide a way
to look up a single phandle and get the Fdt object from a Node.
Simon Glass [Tue, 17 Jul 2018 19:25:45 +0000 (13:25 -0600)]
patman: Show the current directory in GetInputFilename()
When this fails it is useful to see the current directory, since U-Boot's
build system will typically change into the output directory during the
build. Add this information to the error.
Simon Glass [Tue, 17 Jul 2018 19:25:42 +0000 (13:25 -0600)]
patman: Allow test commands to fall back to real ones
Tests use the 'test_result' feature to return a predetermined command
result for particular commands. The avoids needing to have the real
command available just to run a test. It works by calling the function
provided by the test, to get the value.
However sometimes the test does need to run the real command. Allow it to
fall back to do this when the function does not return a result.
Simon Glass [Tue, 17 Jul 2018 19:25:40 +0000 (13:25 -0600)]
binman: Add an entry filled with a repeating byte
It is sometimes useful to have an area of the image which is all zeroes,
or all 0xff. This can often be achieved by padding the size of an an
existing entry and setting the pad byte for an entry or image.
But it is useful to have an explicit means of adding blocks of repeating
data to the image. Add a 'fill' entry type to handle this.
Simon Glass [Tue, 17 Jul 2018 19:25:38 +0000 (13:25 -0600)]
binman: Add support for flashrom FMAP
Add an entry which can hold an FMAP region as used by flashrom, an
open-source flashing tool used on Linux x86 machines. This provides a
simplified non-hierarchical view of the entries in the image and has a
signature at the start to allow flashrom to find it in the image.
Simon Glass [Tue, 17 Jul 2018 19:25:37 +0000 (13:25 -0600)]
binman: Create README.entries
Create a new README containing documentation for the entry types supported
by binman. This provides an easy reference in one place. It is
automatically generated from the source-code documentation.
Simon Glass [Tue, 17 Jul 2018 19:25:36 +0000 (13:25 -0600)]
binman: Allow creation of entry documentation
Binman supports quite a number of different entries now. The operation of
these is not always obvious but at present the source code is the only
reference for understanding how an entry works.
Add a way to create documentation (from the source code) which can be put
in a new 'README.entries' file.
Simon Glass [Tue, 17 Jul 2018 19:25:34 +0000 (13:25 -0600)]
binman: Allow help to work without libfdt
At present binman needs libfdt.py to be available before it will do
anything, even print help. Import those modules later to avoid this, as it
is bad practice to fail to even show help on startup.
Simon Glass [Tue, 17 Jul 2018 19:25:33 +0000 (13:25 -0600)]
binman: Support an entry that holds text
It is useful to able to write an identifying string to the image within an
entry. Add a 'text' entry type to handle this. The actual text is
typically passed to binman on the command line. The text is not itself
nul-terminated but this can be achieved if required by setting the size of
the entry to something larger than the text.
Simon Glass [Tue, 17 Jul 2018 19:25:32 +0000 (13:25 -0600)]
binman: Add support for passing arguments to entries
Sometimes it is useful to pass binman the value of an entry property from
the command line. For example some entries need access to files and it is
not always convenient to put these filenames in the image definition
(device tree).
Add a -a option which can be used like this:
-a<prop>=<value>
where
<prop> is the property to set
<value> is the value to set it to
Simon Glass [Wed, 1 Aug 2018 21:22:42 +0000 (15:22 -0600)]
binman: Add a new 'image-pos' property
At present each entry has an offset within its parent section. This is
useful for figuring out how entries relate to one another. However it
is sometimes necessary to locate an entry within an image, regardless
of which sections it is nested inside.
Add a new 'image-pos' property to provide this information. Also add
some documentation for the -u option binman provides, which updates the
device tree with final entry information.
Since the image position is a better symbol to use for the position of
U-Boot as obtained by SPL, update the SPL symbols to use this instead of
offset, which might be incorrect if hierarchical sections are used.
Simon Glass [Wed, 1 Aug 2018 21:22:37 +0000 (15:22 -0600)]
binman: Rename 'position' to 'offset'
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Simon Glass [Tue, 17 Jul 2018 19:25:24 +0000 (13:25 -0600)]
binman: Don't depend on dict order in ELF testOutsideFile()
At present this test assumes that the symbols are returned in address
order. However, objdump can list symbols in any order and dictionaries do
not guarantee any particular order when iterating through item.
Update elf.GetSymbols() to return an OrderedDict, sorted by address, to
avoid any problems.
Michal Simek [Tue, 31 Jul 2018 06:11:28 +0000 (08:11 +0200)]
dm: Fix CMD_DM enabling
The patch "dm: Change CMD_DM enabling"
(sha1: 08a00cba06a7e608ae65e3d7ea225cf8c639429d) was incorrectly updated
and PICO_IMX7D is missing imply CMD_DM and WARP7 has it twice.
This patch is fixing it.
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ran Wang [Thu, 14 Jun 2018 02:45:40 +0000 (10:45 +0800)]
Revert "powerpc/T104xRDB: Fix endian access issue on EHCI intinalization"
There was an EHCI endian accessor issue. Now it's fixed by commit 9829ce2ff25c ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit e6a727fffec7 ("powerpc/T104xRDB: Fix
endian access issue on EHCI intinalization"). On T104x platform,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Thu, 14 Jun 2018 02:45:39 +0000 (10:45 +0800)]
Revert "powerpc/p1_p2_rdb_pc: Fix endian access issue on EHCI intinalization"
There was an EHCI endian accessor issue. Now it's fixed by commit 9829ce2ff25c ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit 0f2296bab141 ("powerpc/p1_p2_rdb_pc:
Fix endian access issue on EHCI intinalization"). On P1 P2 platforms,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Jagan Teki [Sat, 28 Jul 2018 18:33:31 +0000 (00:03 +0530)]
board: sun50i: h6: Add OrangePi One Plus initial support
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
mtd: nand: sunxi: Return on set_feature only when not ENOTSUPP
Return the error code of the set_features function only if
the error code is not ENOTSUPP. Otherwise, if this function
is not supported, it will return and fail to initialize the
NAND.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com> Acked-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Fri, 20 Jul 2018 07:04:21 +0000 (12:34 +0530)]
phy: sun4i-usb: Remove usb_clk_cfg set in probe
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Fri, 20 Jul 2018 07:04:20 +0000 (12:34 +0530)]
phy: sun4i-usb: Call phy_passby even for PHY#0
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.
Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
video: sunxi: de2: fix SimpleFB node creation when DE2 not probed
Sometimes when a monitor without EDID information is plugged, the DE2
won't be probed (because of lack of timing information), but the HDMI
node is probed, thus a SimpleFB node with invalid information will be
populated.
Also detect whether DE2 is probed when creating SimpleFB node.
Fixes: be5b96f0e411 ("sunxi: setup simplefb for Allwinner DE2") Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Jagan Teki <jagan@openedev.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
projects / u-boot.git / log