SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Currently there are two problems in 'bootelf -p' (load elf by segments)
command:
- bss section is not flushed, so booted elf can have non zero values
in bss;
- at least on ARM there are 'CACHE: Misaligned operation at
range...' warnings
Use p_memsz instead of p_filesz during cache flushing for elf segment.
p_filesz doesn't include zero initialized memory (e.g. bss section),
which also should be flushed.
Align these cache flushes to line boundaries.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Before the patch scsi would report the same device number for all SCSI
devices, e.g.
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 0: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
With the patch the same device number is reported as is used in
scsi_read():
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 1: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ang, Chee Hong [Mon, 18 Feb 2019 04:07:50 +0000 (20:07 -0800)]
ARM: socfpga: stratix10: Return valid error code from FPGA driver
This patch prevent the Stratix 10 FPGA driver incorrectly return the
transaction ID as the mailbox error code. It should always return the
actual mailbox error code from SDM firmware.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Thu, 14 Feb 2019 14:16:15 +0000 (15:16 +0100)]
mmc: tmio: sdhi: Configure DT2FF register for HS400 mode
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Marek Vasut [Tue, 29 Jan 2019 03:45:51 +0000 (04:45 +0100)]
mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
- Add missing function descriptions.
- Update existing function descriptions to match Sphinx style.
- Add lib/efi_loader/efi_image_loader.c to the input files for Sphinx
generated documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If we want to properly unload images in Exit() the memory should always be
allocated in the same way. As we allocate memory when reading from file we
should do the same when the original image is in memory.
A further patch will be needed to free the memory when Exit() is called.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: error handling in efi_setup_loaded_image()
In case of an error we should set the returned pointers to NULL. This
ensures that an illegal free does not occur even if the caller calls
free() for the handles.
If protocols cannot be installed, release all resources.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In test/py/conftest.py the assumption is made that for if a test is called
with `ut unicode` the test function name starts with 'unicode_test_'. As
the Unicode tests did not follow this naming scheme they were not executed
by `make tests`.
Rename the Unicode test functions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
lib/vsprintf: print '?' for illegal Unicode sequence
Commit 0e66c10a7d80 ("lib: vsprintf: avoid overflow printing UTF16
strings") broke the Unicode unit tests: an illegal UTF16 code point
should be printed as '?'.
If the path passed to efi_dp_split_file_path() does not contain a
reference to a file it returns EFI_OUT_OF_RESOURCES. This does not properly
indicate the kind of the problem that occurred. Return
EFI_INVALID_PARAMETER instead.
Update function description.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Sat, 16 Feb 2019 02:21:28 +0000 (21:21 -0500)]
Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tim Harvey [Mon, 4 Feb 2019 21:11:00 +0000 (13:11 -0800)]
imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+)
device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit 8dccafaa281aa1d240a58bbcdff338aec114a021.
This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
- enabling MMC UHS-I on board revisions that support it
- enabling PWM based on hwconfig
- fixing PCIe reset on GW552x
- removing cpu external watchdog reset on boards that do not support it
- populate PCI dt nodes based on PCI scan in order to fix GW16082
interrupt mapping and inject MAC address for PCI based GbE
Tim Harvey [Mon, 4 Feb 2019 21:10:57 +0000 (13:10 -0800)]
imx: ventana: add support for GW5909
The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Tim Harvey [Mon, 4 Feb 2019 21:10:56 +0000 (13:10 -0800)]
imx: ventana: add support for GW5908
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Tim Harvey [Mon, 4 Feb 2019 21:10:55 +0000 (13:10 -0800)]
imx: ventana: add support for GW5907
The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
- DDR3 memory (512MB default)
- 1x GigE (i.MX6 FEC)
- Gateworks System Controller
Tim Harvey [Mon, 4 Feb 2019 21:10:50 +0000 (13:10 -0800)]
imx: ventana: add support for GW5905
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
- eMMC flash (boot device)
- microSD expansion
- LVDS display connector for off-board 3D+1C with PWM backlight
and I2C based touch controller
- MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
- ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
- ublox ZOE-M8Q GPS
- LSM9DS1 9-DOF IMU
- 1x 1-lane miniPCIe socket with USB 2.0
- Gateworks System Controller
- Audio jack with TLV320AIC Audio Codec, Speaker AMP
and TSA227E Headphone detect
- MAX8607 3-mode LED camera flash
- DECT ULE module
- FUSB302 USB-C PD and ISL9238 Battery charger
Tim Harvey [Mon, 4 Feb 2019 21:10:49 +0000 (13:10 -0800)]
imx: ventana: remove setup of I2C3 from SPL
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Abel Vesa [Fri, 1 Feb 2019 16:40:25 +0000 (16:40 +0000)]
configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI support
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:14 +0000 (16:40 +0000)]
arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] files
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:07 +0000 (16:40 +0000)]
usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
Stefan Roese [Wed, 30 Jan 2019 07:54:12 +0000 (08:54 +0100)]
video: bmp: Add support for 24bpp BMP files on 16bpp displays
This patch adds support to load 24bpp BMP files on 16bpp displays. This
will be used by the theadorable board. The "old" bmp command did support
this operartion mode and to not break compatibility with the move to
DM_VIDEO, we need to add this support to the "new" bmp code.
Michal Simek [Thu, 14 Feb 2019 12:14:30 +0000 (13:14 +0100)]
arm64: zynqmp: Create fdtfile from compatible string
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
Amit Kucheria [Thu, 23 Aug 2018 08:53:29 +0000 (14:23 +0530)]
arm64: dts: Fix various entry-method properties to reflect documentation
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Add reset-on-timeout for all boards and modify default timeout value
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:20 +0000 (00:10 -0400)]
ARM: dts: zynq: correct and improve the model property of dt files
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tim Harvey [Mon, 4 Feb 2019 20:56:52 +0000 (12:56 -0800)]
net: mv88e61xx: fix autonegotiation on ports
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
projects / u-boot.git / log