Rasmus Villemoes [Thu, 19 Aug 2021 09:57:03 +0000 (11:57 +0200)]
watchdog: wdt-uclass.c: handle all DM watchdogs in watchdog_reset()
A board can have and make use of more than one watchdog device, say
one built into the SOC and an external gpio-petted one. Having
wdt-uclass only handle the first is both a little arbitrary and
unexpected.
So change initr_watchdog() so we visit (probe) all DM watchdog
devices, and call the init_watchdog_dev helper for each.
Similarly let watchdog_reset() loop over the whole uclass - each
having their own ratelimiting metadata, and a separate "is this device
running" flag.
This gets rid of the watchdog_dev member of struct global_data. We
do, however, still need the GD_FLG_WDT_READY set in
initr_watchdog(). This is because watchdog_reset() can get called
before DM is ready, and I don't think we can call uclass_get() that
early.
The current code just returns 0 if "getting" the first device fails -
that can of course happen because there are no devices, but it could
also happen if its ->probe call failed. In keeping with that, continue
with the handling of the remaining devices even if one fails to
probe. This is also why we cannot use uclass_probe_all().
If desired, it's possible to later add a per-device "u-boot,autostart"
boolean property, so that one can do CONFIG_WATCHDOG_AUTOSTART
per-device.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Thu, 19 Aug 2021 09:57:02 +0000 (11:57 +0200)]
board: x530: switch to wdt_stop_all()
Since the gd->watchdog_dev member is going away, switch to using the
new wdt_stop_all() helper.
While here, clean up the preprocessor conditional: The ->watchdog_dev
member is actually guarded by CONFIG_WDT [disabling that in
x530_defconfig while keeping CONFIG_WATCHDOG breaks the build], and in
the new world order so is the existence of the wdt_stop_all()
function.
Actually, existence of wdt_stop_all() depends on CONFIG_${SPL_}WDT, so
really spell the condition using CONFIG_IS_ENABLED, and make it a C
rather than cpp if.
Rasmus Villemoes [Thu, 19 Aug 2021 09:57:01 +0000 (11:57 +0200)]
watchdog: wdt-uclass.c: add wdt_stop_all() helper
Since the watchdog_dev member of struct global_data is going away in
favor of the wdt-uclass handling all watchdog devices, prepare for
that by adding a helper to call wdt_stop() on all known devices.
If an error is encountered, still do wdt_stop() on remaining devices,
but remember and return the first error seen.
Initially, this will only be used in one single
place (board/alliedtelesis/x530/x530.c).
Rasmus Villemoes [Thu, 19 Aug 2021 09:57:00 +0000 (11:57 +0200)]
sandbox: disable CONFIG_WATCHDOG_AUTOSTART
For the unit tests, it is more convenient if the tests are in charge
of when the watchdog devices are started and stopped, so prevent
wdt-uclass from doing it automatically.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Thu, 19 Aug 2021 09:56:59 +0000 (11:56 +0200)]
watchdog: wdt-uclass.c: keep track of each device's running state
As a step towards handling all DM watchdogs in watchdog_reset(), use a
per-device flag to keep track of whether the device has been started
instead of a bit in gd->flags.
We will still need that bit to know whether we are past
initr_watchdog() and hence have populated gd->watchdog_dev -
incidentally, that is how it was used prior to commit 9c44ff1c5f3c.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Thu, 19 Aug 2021 09:56:56 +0000 (11:56 +0200)]
watchdog: wdt-uclass.c: introduce struct wdt_priv
As preparation for having the wdt-uclass provided watchdog_reset()
function handle all DM watchdog devices, and not just the first such,
introduce a uclass-owned struct to hold the reset_period and
next_reset, so these become per-device instead of being static
variables.
No functional change intended.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Thu, 19 Aug 2021 09:56:55 +0000 (11:56 +0200)]
watchdog: wdt-uclass.c: use wdt_start() in wdt_expire_now()
wdt_start() does the "no ->start? return -ENOSYS" check, don't
open-code that in wdt_expire_now().
Also, wdt_start() maintains some global (and later some per-device)
state, which would get out of sync with this direct method call - not
that it matters much here since the board is supposed to reset very
soon.
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tom Rini [Mon, 30 Aug 2021 20:44:54 +0000 (16:44 -0400)]
Merge branch '2021-08-30-kconfig-migrations-part1' into next
- Begin merging some Kconfig migration, and CONFIG namespace cleanup
series in. This gives us:
- A number of I2C symbols migrated over
- DWC2, i8042, altera_spi and a few other areas updated to use CFG not
CONFIG for the concept of "configuration space" defines.
- Rename CONFIG_EXTRA_ENV_BOARD_SETTINGS to EXTRA_ENV_BOARD_SETTINGS
- Some dead code removal.
- Rename a number of CONFIG symbols that were only referenced within
the config header to not use CONFIG as a prefix.
Tom Rini [Thu, 19 Aug 2021 19:16:15 +0000 (15:16 -0400)]
astro_mcf5373l: Rework ASTRO_ID logic
Rather than using CONFIG namespace for logic internal to
include/configs/astro_mcf5373l.h to select ASTRO_ID (and populate the
default environment), strip CONFIG from the various options used and
set.
Tom Rini [Thu, 19 Aug 2021 18:58:00 +0000 (14:58 -0400)]
i8042: Do not abuse CONFIG namespace
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 19 Aug 2021 18:19:39 +0000 (14:19 -0400)]
arm: Migrate GICV2 / GICV3 to Kconfig
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC
related registers that need to be handled more cleanly but start by
moving this symbol to Kconfig.
Tom Rini [Thu, 19 Aug 2021 17:56:20 +0000 (13:56 -0400)]
nand: vf610_nfc: Do not abuse CONFIG namespace
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 19 Aug 2021 03:12:35 +0000 (23:12 -0400)]
i2c: fsl_i2c: Migrate to Kconfig
- As there are no boards that use different values for speed / slave on
different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
common to all users.
- Convert all remaining symbols to Kconfig.
Tom Rini [Thu, 19 Aug 2021 03:12:33 +0000 (23:12 -0400)]
Convert CONFIG_SYS_I2C_MXC et al to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Tom Rini [Thu, 19 Aug 2021 03:12:29 +0000 (23:12 -0400)]
ti: i2c: Convert CONFIG_SYS_OMAP24_I2C to CONFIG_SYS_I2C namespace
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Tom Rini [Thu, 19 Aug 2021 03:12:25 +0000 (23:12 -0400)]
Convert CONFIG_SYS_I2C_EARLY_INIT to Kconfig
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Tom Rini [Thu, 19 Aug 2021 03:12:24 +0000 (23:12 -0400)]
Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Tom Rini [Tue, 17 Aug 2021 21:59:48 +0000 (17:59 -0400)]
i2c: Remove unused additional legacy soft i2c bus support
Currently the legacy software i2c support is only used for a single bus.
Remove all of the extra and unused support. Also update the README to
not reference that, and finish removing some already badly auto-edited
related text.
Tom Rini [Tue, 17 Aug 2021 21:59:45 +0000 (17:59 -0400)]
Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Tom Rini [Tue, 17 Aug 2021 21:59:44 +0000 (17:59 -0400)]
eeprom: Drop CONFIG_ENV_EEPROM_IS_ON_I2C usage
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Tom Rini [Tue, 17 Aug 2021 21:59:43 +0000 (17:59 -0400)]
cl-som-imx7: Enable CMD_EEPROM
This platform defines everything needed to be able to use the
eeprom command. In addition, board/compulab/common/eeprom.c is required
by the platform, and does not use CONFIG_ID_EEPROM to enable/disable
builing of it. In order to migrate CONFIG symbols to Kconfig and to not
have to add complex logic to handle this case, enable CMD_EEPROM on this
board.
Cc: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Aug 2021 21:59:42 +0000 (17:59 -0400)]
i2c: S3C24X0: Finish Kconfig migration
Finish moving this driver to Kconfig.
- Update the dependency logic for Exynos5 too
- Remove the unused CONFIG_SYS_I2C_S3C24X0_SPEED variable
- Drop CONFIG_SYS_I2C_S3C24X0_SLAVE as it's always set to 0.
- Move the internal SYS_I2C_S3C24X0_SLAVE define closer to the only user.
Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Tue, 17 Aug 2021 21:59:40 +0000 (17:59 -0400)]
siemens: Move CONFIG_SYS_I2C_EEPROM_ADDR usage out of CONFIG namespace
The instances of CONFIG_SYS_I2C_EEPROM_ADDR on these platforms doesn't
match up with the rest of the EERPOM related defines in U-Boot. Move
these out of the CONFIG namespace rather than make complex Kconfig
logic.
Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tom Rini [Tue, 17 Aug 2021 21:59:39 +0000 (17:59 -0400)]
keymile: Use CONFIG_SYS_IVM_EEPROM_ADR
As the code reads now, making this code path use
CONFIG_SYS_IVM_EEPROM_ADR rather than CONFIG_SYS_I2C_EEPROM_ADDR seems
to make sense as the rest of the EEPROM infrastructure isn't used on
these platforms.
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Tom Rini [Tue, 17 Aug 2021 21:59:38 +0000 (17:59 -0400)]
arm: shc: Change CONFIG_SYS_I2C_EEPROM_ADDR to EEPROM_ADDR
The shc platforms do not make use of the rest of the EEPROM
infrastructure. Rather than make more elaborate Kconfig logic, remove
this setting from the CONFIG namespace.
Tom Rini [Tue, 17 Aug 2021 21:59:37 +0000 (17:59 -0400)]
davinci: Drop CONFIG_MAC_ADDR_IN_EEPROM
Looking over the current boards, there are no users of
CONFIG_MAC_ADDR_IN_EEPROM. Further, omapl138_lcdk uses
CONFIG_NET_RANDOM_ETHADDR. Drop various unused code paths.
Cc: Adam Ford <aford173@gmail.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Aug 2021 21:59:36 +0000 (17:59 -0400)]
kp_imx53: Switch to using a local namespace for ID EEPROM
This platform does not use any of the standard EEPROM functionality and
instead provides its own. Use a local namespace for the I2C related
defines to access the EEPROM.
Tom Rini [Tue, 10 Aug 2021 20:17:55 +0000 (16:17 -0400)]
usb: dwc2: Rename CONFIG_DWC2 namespace to DWC2
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 27 Aug 2021 12:33:02 +0000 (08:33 -0400)]
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
Michal Simek [Tue, 24 Aug 2021 12:56:47 +0000 (14:56 +0200)]
xilinx: zynqmp: Enable stack relocation to DDR
There is no space in OCM for SPL stack because the space in OCM is occupied
by TF-A. That's why move relocate stack to DDR to 0x18000000 address
and also enable SPL_SIZE_LIMIT not to be more then 0xfffea000 which is
default address for TFA.
It is good to summarize current DDR usage in SPL flow.
0-0x80000 is used for BSS
(CONFIG_SPL_BSS_START_ADDR, CONFIG_SPL_BSS_MAX_SIZE)
0x100000 is used for DTB passing address
(CONFIG_XILINX_OF_BOARD_DTB_ADDR)
0x17fffe70 - CONFIG_SPL_STACK_R_ADDR - is used for GD
0x18000000 is used for SPL stack
(CONFIG_SPL_STACK_R_ADDR)
0x20000000-0x21000000 is used for SPL malloc area
(CONFIG_SYS_SPL_MALLOC_START, CONFIG_SYS_SPL_MALLOC_SIZE)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 11 Aug 2021 12:23:54 +0000 (14:23 +0200)]
xilinx: common: Enabling generic function for DT reselection
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.
When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.
If CC is not present or more are available it keeps going.
When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.
From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.
needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo
and only one dtb is in fit:
config_X {
description = "zynqmp-board-cc";
fdt = "board-cc";
};
For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb
When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 19 Aug 2021 10:02:57 +0000 (12:02 +0200)]
xilinx: zynqmp: Generate different u-boot.itb for MULTI_DTB_FIT
When MULTI_DTB_FIT is enabled fit-dtb.blob fit image is created which
contain all DTBs listed by CONFIG_OF_LIST. And with DTB_RELESELECT there is
a need to handle it as one file with DTBs in it not as separate DTBs in
u-boot.its/itb.
That's why extend mkimage_fit_atf.sh to generate u-boot.itb correctly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 19 Aug 2021 09:09:37 +0000 (11:09 +0200)]
Makefile: Align fit-dtb.blob and u-boot.itb by 64bits
Enabling MULTI_DTB_FIT and DTB_RESELECT can end up with multi DTBs in FIT
image placed and aligned only by 32bits (4bytes). Based on device tree
specification:
"Specifically, the memory reservation block shall be aligned to an 8-byte boundary
and the structure block to a 4-byte boundary."
is 64bit (8bytes) alignment required. That's why make sure that
fit-dtb.blob and u-boot.itb as our primary target images for Xilinx ZynqMP
are all 64bit aligned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Michal Simek [Thu, 19 Aug 2021 09:07:59 +0000 (11:07 +0200)]
xilinx: zynqmp: Check that DT is 64bit aligned
DT needs to be 64bit aligned. If it is not fdt64_to_cpu will fail when try
to read information about reserved memory. The system ends in exception
without any clue what's going it. That's why detect not aligned DT and
panic to show where the issue is coming from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 23 Jul 2021 07:59:59 +0000 (09:59 +0200)]
xilinx: Add support for generic board detection
Add support for changing DT at run time. It is done via board_detection()
which returns platform_id and platform_version which can be used via
board_name_decode() to compose board_local_name string which corresponds
with DT which is should be used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 12 Aug 2021 10:30:36 +0000 (12:30 +0200)]
xilinx: common: Change board_info[] handling
Origin code was allocating only pointers to struct xilinx_board_description
and there was separate allocation for structure self and freeing in case of
failure.
The code is directly allocating space for all structures by one calloc to
simlify logic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 23 Jul 2021 07:55:59 +0000 (09:55 +0200)]
xilinx: Use variable for passing board_name
Use variable which points to DEVICE_TREE by default. The reason for this
change is to enable DTB_RESELECT and MULTI_DTB_FIT where board detection
can be used for change DTB at run time. That's why there must be reference
in board_fit_config_name_match() via variable instead of hardcoding it
which is sufficient for that use case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 12 Aug 2021 09:03:49 +0000 (11:03 +0200)]
xilinx: fru: Replace spaces with \0 in detected name
FRU spec expected \0 for unused symbols but unfortunately a lot of boards
are using spaces instead of \0. That's why after saving it to desc->name
name is checked again and all spaces are converted to \0. This will ensure
that names can be used for string manipulations like concatenation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 11 Aug 2021 10:01:25 +0000 (12:01 +0200)]
cmd: boot: Update reset usage message
The commit 573a3811edc8 ("sysreset: psci: support system reset in a generic
way with PSCI") has added support for warm reset via PSCI but this hasn't
been reflected in usage message and user has to look at the code how to run
it. That's why update usage text to make this clear.
Here is full help with updated usage:
ZynqMP> help reset
reset - Perform RESET of the CPU
Usage:
reset - cold boot without level specifier
reset -w - warm reset if implemented
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Michal Simek [Thu, 1 Jul 2021 09:44:51 +0000 (11:44 +0200)]
cmd: pwm: Remove additional pwm description
The first name is taken from command name that's why shouldn't be listed in
help. And commands shouldn't be listed with <> which means value but value
itself is command name.
Also add description for commands to make it clear what it does.
T Karthik Reddy [Tue, 10 Aug 2021 12:50:19 +0000 (06:50 -0600)]
soc: xilinx: versal: Add soc_xilinx_versal driver
soc_xilinx_versal driver allows identification of family & revision
of versal SoC. This driver is selected by CONFIG_SOC_XILINX_VERSAL.
Probe this driver using platdata U_BOOT_DEVICE structure which is
defined at mach-versal/cpu.c.
Add this config to xilinx_versal_virt_defconfig &
xilinx_versal_mini_ospi_defconfig file to select this driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Tue, 10 Aug 2021 12:50:18 +0000 (06:50 -0600)]
soc: xilinx: zynqmp: Add soc_xilinx_zynqmp driver
soc_xilinx_zynqmp driver allows identification of family & revision
of zynqmp SoC. This driver is selected by CONFIG_SOC_XILINX_ZYNQMP.
Add this config to xilinx_zynqmp_virt_defconfig file.
Probe this driver using platdata U_BOOT_DEVICE structure which is
specified in mach-zynqmp/cpu.c.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 10 Aug 2021 07:21:54 +0000 (09:21 +0200)]
fdt_support: Add kernel-doc for fdt_fixup_memory_banks()
Add kernel-doc description for fdt_fixup_memory_banks() because it is
implemented in one specific way and this information should be available
for others to decide if their SoC conforms to it.
If you don't want U-Boot to update your memory DT layout please disable
CONFIG_ARCH_FIXUP_FDT_MEMORY.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Fri, 6 Aug 2021 12:09:32 +0000 (14:09 +0200)]
xilinx: Disable ARCH_FIXUP_FDT_MEMORY
Based on DT spec you can have one memory node which multiple ranges or
multiple nodes.
fdt_fixup_memory_banks() is not implemented in a correct way when multiple
memory nodes are present because all ranges are put it to the first memory
node found. And next memory nodes are kept in DT which ends up in the same
range specification in the same DT.
Here is what it is happening.
Origin DT.
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
xilinx: Add jedec compatible string for QSPI (Zynq/ZynqMP)
Add missing "jedec, spi-nor" compatible string for QSPI flash node.
Spi-nor framework uses this compatibility string to probe &
initialize flash. With missing compatibility string we are observing
below error:
Zynq> sf probe 0 0 0
jedec_spi_nor spi_flash@0:0: unrecognized JEDEC id bytes:
00, 00, 00 Failed to initialize SPI flash at 0:0 (error -2)
Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 29 Jul 2021 12:22:05 +0000 (14:22 +0200)]
xilinx: zynqmp: Initialize usb and scsi via preboot
Based on thread
https://lists.denx.de/pipermail/u-boot/2021-June/451828.html
especially
"Overall we have a deficiency in the UEFI implementation in that we
cannot deal with block devices added or removed after initialization."
there is a need to deal with removable media as usb/scsi/sata.
That's why bridge this gap in EFI implementation by resetting usb and
scsi resets to get all disks before efi_init_obj_list() is called.
In our standard boot flow, where we use distro boot, order is fixed as
"jtag mmc0 mmc1 qspi0 nand0 usb0 usb1 scsi0 pxe dhcp" with prioritizing
boot device added by commit 2882b39d564b ("arm64: zynqmp: Setup the first
boot_target at run time").
When device has ESP partition all devices should be detected because then
efi_disk_register() in efi_init_obj_list() is called only once.
The first such a device is sd/emmc(mmc0/mmc1) and then disks on usb/sata
are not handled at all.
The commit 6bb577dbb30f ("arm64: zynqmp: Disable
EFI_CAPSULE_ON_DISK_EARLY") also pointed out on this issue but detection of
removable media wasn't solved that's why do it now via preboot command.
I have tested cases without usb and scsi and there is no problem with
calling resets without devices itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 6 Aug 2021 07:18:17 +0000 (09:18 +0200)]
arm64: zynqmp: Disable WDT_CDNS driver by default
Do not enable watchdog driver in default zynqmp configuration. The reason
is that not all distributions are handling watchdog properly and then
expires and system resets. If someone needs watchdog in their design please
enable it by hand.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Tue, 3 Aug 2021 05:20:45 +0000 (23:20 -0600)]
mmc: zynq_sdhci: Wait till sd card detect state is stable
As per SD spec when SD host controller is reset, it takes 1000msec
to detect the card state. In case, if we enable the sd bus voltage &
card detect state is not stable, then host controller will disable
the sd bus voltage.
In case of warm/subsystem reboot, due to unstable card detect state
host controller is disabling the sd bus voltage to sd card causing
sd card timeout error. So we wait for a maximum of 1000msec to get
the card detect state stable before we enable the sd bus voltage.
This current fix is workaround for now, this needs to be analysed
further. Zynqmp platform should behave the same as Versal, but we
did not encounter this issue as of now. So we are fixing it for
Versal only.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mmc: zynq_sdhci: Move setting tapdelay code to driver
Move tapdelay function calls to zynq_sdhci.c and make them static
inline. zynqmp_tap_delay.h has function prototypes for the functions
defined in tap_delays.c, which will not be needed anymore.
mmc: zynq_sdhci: Add xilinx_pm_request() method to set tapdelays
Currently xilinx sdhci driver is using zynqmp_mmio_write() to set
tapdelay values and DLL resets. Continue to use this for SPL and mini
U-Boot where U-Boot will be executed at EL3 level.
Use firmware call xilinx_pm_request() using appropriate arguments to
set input/output tapdelays and also for DLL resets in regular flow(EL2).
Host driver should explicitly request DLL reset before ITAP (assert DLL)
and after OTAP (release DLL) to avoid issues in some cases. Also handle
error return where possible.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
projects / u-boot.git / log