Simon Glass [Mon, 18 Jun 2018 14:08:28 +0000 (08:08 -0600)]
efi: Drop error return in efi_carve_out_dt_rsv()
This function currently returns an error code, but never uses it. There is
no function comment so it is not obvious why. Presuambly the error is not
important.
Update the function to explain its purpose and why it ignores the error.
Drop the useful error return value.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Simon Glass [Mon, 18 Jun 2018 14:08:20 +0000 (08:08 -0600)]
vsprintf: Handle NULL with %pU
At present a NULL pointer passed to printf for a %pU argument will cause
U-Boot to access memory at 0. Fix this by adding a check, and print
"(null)" instead.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexander Graf <agraf@suse.de>
[agraf: s/(null)/<NULL>/] Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 18 Jun 2018 15:23:15 +0000 (17:23 +0200)]
efi_loader: Expose U-Boot addresses in memory map for sandbox
We currently expose host addresses in the EFI memory map. That can be
bad if we ever want to use sandbox to boot strap a real kernel, because
then the kernel would fetch its memory table from our host virtual address
map. But to make that use case work, we would need to have full control
over the address space the EFI application sees.
So let's expose only U-Boot addresses to the guest until we get to the
point of allocation. EFI's allocation functions are fun - they can take
U-Boot addresses as input values for hints and return host addresses as
allocation results through the same uint64_t * parameter. So we need to
be extra careful on what to pass in when.
With this patch I am successfully able to run the efi selftest suite as
well as grub.efi on aarch64.
Simon Glass [Mon, 18 Jun 2018 15:23:12 +0000 (17:23 +0200)]
efi: sandbox: Adjust memory usage for sandbox
With sandbox the U-Boot code is not mapped into the sandbox memory range
so does not need to be excluded when allocating EFI memory. Update the EFI
memory init code to take account of that.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Remove map_sysmem() call and header reference] Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 18 Jun 2018 15:23:05 +0000 (17:23 +0200)]
efi_loader: Introduce ms abi vararg helpers
Varargs differ between sysv and ms abi. On x86_64 we have to follow the ms
abi though, so we also need to make sure we use x86_64 varargs helpers.
This patch introduces generic efi vararg helpers that adhere to the
respective EFI ABI. That way we can deal with them properly from efi
loader code and properly interpret variable arguments.
This fixes the InstallMultipleProtocolInterfaces tests in the efi selftests
on x86_64 for me.
When running on the sandbox the stack is not necessarily at a higher memory
address than the highest free memory.
There is no reason why the checking of the highest memory address should be
more restrictive for EFI_ALLOCATE_ANY_PAGES than for
EFI_ALLOCATE_MAX_ADDRESS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: use -1ULL instead] Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 18 Jun 2018 15:23:00 +0000 (17:23 +0200)]
efi_loader: Allow SMBIOS tables in highmem
We try hard to make sure that SMBIOS tables live in the lower 32bit.
However, when we can not find any space at all there, we should not
error out but instead just fall back to map them in the full address
space instead.
This can for example happen on systems that do not have any RAM mapped
in the lower 32bits of address space. In that case having any SMBIOS
tables at all is better than having none.
Alexander Graf [Mon, 18 Jun 2018 15:22:58 +0000 (17:22 +0200)]
efi_loader: Use map_sysmem() in bootefi command
The bootefi command gets a few addresses as values passed in. In sandbox,
these values are in U-Boot address space, so we need to make sure we
explicitly call map_sysmem() on them to be able to access them.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 18 Jun 2018 15:22:57 +0000 (17:22 +0200)]
efi_loader: Use compiler constants for image loader
The EFI image loader tries to determine which target architecture we're
working with to only load PE binaries that match.
So far this has worked based on CONFIG defines, because the target CPU
was always indicated by a config define. With sandbox however, this is
not longer true as all sandbox targets only encompass a single CONFIG
option and so we need to use compiler defines to determine the CPU
architecture.
Mark Kettenis [Fri, 15 Jun 2018 21:47:14 +0000 (23:47 +0200)]
ARM: HYP/non-sec: enable ARMV7_LPAE if HYP mode is supported
ARMV7_LPAE is required in order to enable the MMU in HYP mode.
And we really want to enable the MMU in HYP mode such that we can
enable the the caches. Otherwise U-Boot code (such as the EFI
implementation) that runs in HYP mode will run at a snils pace.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Mark Kettenis [Fri, 15 Jun 2018 21:47:13 +0000 (23:47 +0200)]
efi_loader: ARM: don't attempt to enter non-secure mode twice
Multiple EFI binaries may be executed in sequence. So if we already
are in non-secure mode after running the first one we should skip
the switching code since it no longer works once we're non-secure.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Mark Kettenis [Fri, 15 Jun 2018 21:47:12 +0000 (23:47 +0200)]
efi_loader: ARM: run EFI payloads non-secure
If desired (and possible) switch into HYP mode or non-secure SVC mode
before calling the entry point of an EFI application. This allows
U-Boot to provide a usable PSCI implementation and makes it possible
to boot kernels into hypervisor mode using an EFI bootloader.
Based on diffs from Heinrich Schuchardt and Alexander Graf.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
[agraf: Fix indentation] Signed-off-by: Alexander Graf <agraf@suse.de>
Mark Kettenis [Fri, 15 Jun 2018 21:47:11 +0000 (23:47 +0200)]
ARM: HYP/non-sec: migrate stack
The current code that switches into HYP mode doesn't bother to set
up a stack for HYP mode. This doesn't work for EFI applications
as they expect a usable stack. Fix this by migrating the stack
pointer from SP_svc to SP_hyp while in Monitor mode.
This restores the stack pointer when we drop into HYP mode.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Our nand_ecc_modes_t is already a bit abused by value NAND_ECC_SOFT_BCH.
This enum should store ECC mode only and putting algorithm details there
is a bad idea. It would result in too many values impossible to support
in a sane way.
To solve this problem let's add a new enum. We'll have to modify all
drivers to set it properly but once it's done it'll be possible to drop
NAND_ECC_SOFT_BCH. That will result in a cleaner design and more
possibilities like setting ECC algorithm for hardware ECC mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b0fcd8ab7b3c89b5da7fff5224d06ed73e7a33cc]
[Philippe Reynes: adapt code to u-boot] Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Adam Ford [Fri, 13 Jul 2018 20:27:13 +0000 (15:27 -0500)]
ARM: configs: omap3_logic: remove Legacy OMAP3 USB driver
Only the MUSB driver is currently supported on the omap3_logic
boards. The driver is using the new-musb and not the legacy
version, so this patch removes the dead code references.
Adam Ford [Tue, 10 Jul 2018 10:23:37 +0000 (05:23 -0500)]
ARM: DTS: am3517-evm-u-boot: Mark MMC1 with cd-inverted
In order to use the device tree for MMC, the card-detect pin
needs to be inverted. This patch places this into the
am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files
clean and in-sync with Linux
Adam Ford [Tue, 10 Jul 2018 10:04:38 +0000 (05:04 -0500)]
ARM: dts: am3517-evm-uboot: Add reg-shift for UART
With the resync of the omap3.dtsi file, the reg-shift was removed
so it breaks the UART. Adding the reg-shift into the
am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps
the dts/dtsi files clean from Linux.
Mario Six [Tue, 10 Jul 2018 06:40:17 +0000 (08:40 +0200)]
doc: Replace DocBook with sphinx-based docs
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Adam Ford [Tue, 10 Jul 2018 01:14:25 +0000 (20:14 -0500)]
ARM: dts: Resync OMAP3 and omap36xx with Linux 4.18-RC4
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux. An addition include/dt-binding was
also brought with it.
Adam Ford [Fri, 20 Jul 2018 13:25:53 +0000 (08:25 -0500)]
configs: imx6q_logic: Cleanup ramdiskaddr and fdtaddr
There are already definitions for ramdisk_addr_r and fdt_addr_r, so
having a duplicate copy called ramdiskaddr and fdtaddr is confusing.
This patch converts any references to ramdisk_addr_r and fdt_addr_r
and removes the duplicates.
Martin Kaiser [Mon, 16 Jul 2018 20:11:57 +0000 (22:11 +0200)]
mx25: fix the offset between the USB ports' registers
The USBOH module on imx25 chips contains two USB controllers which are
called USB OTG Controller and USB Host Controller. Each one has its EHCI
root hub. The OTG Controller's EHCI registers start at offset 0, the Host
Controller's registers start at offset 0x400.
We set CONFIG_MXC_USB_PORT=0 to select the OTG Controller and 1 for the
Host Controller. Therefore, IMX_USB_PORT_OFFSET must be 0x400. Using
this setting, the Host Controller starts working on my imx25 board.
Please note that the imx25 reference manual claims that the Host
Controller's registers start at 0x200. This is not correct. The Linux
Kernel uses the correct offset 0x400 in imx25.dtsi.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signing parts of a u-boot imximage for image verification in High
Assurance Boot (HAB) in a post-build process, requires some
information from the imximage header. Currently, this information is
only provided during the image build, which makes the transfer of this
information to the post-build process harder than necessary.
The i.MX HAB information (start and length) can be calculated either
by using information from the image-configuration file, or from the
information in the flash header of the imximage.
The advantage of using information from flash header is, that they are
not only available during image creation, but also available if
existing images are processed.
Adam Ford [Fri, 6 Jul 2018 01:58:24 +0000 (20:58 -0500)]
imx: i.mx6q: imx6q_logic: Migrate to SPL and enable SDP
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Fabio Estevam [Fri, 29 Jun 2018 18:19:14 +0000 (15:19 -0300)]
pico-imx7d: Add Falcon mode support
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Fri, 29 Jun 2018 18:19:07 +0000 (15:19 -0300)]
pico-imx7d: Fix common distro configuration behavior
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid`
environment helper to allow it to properly work with Yocto Project and
other distributions using extlinux autogenerated configuration files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Mark Jonas [Thu, 28 Jun 2018 13:56:18 +0000 (15:56 +0200)]
arm, imx6: add alternative PAD_CTL_DSE constants
Not all i.MX6 pads use the same drive strength table. So far only the
240 Ohm to 34 Ohm table was available. Because the constants used have
speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when
according to the reference manual 52 Ohm is the correct value. This
patch adds the 260 Ohm to 37 Ohm table.
For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock)
uses the added table.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
Stefan Agner [Tue, 26 Jun 2018 09:10:52 +0000 (11:10 +0200)]
colibri_imx7: improve DDR3 timing
This makes sure that all Colibri iMX7 modules work with the
same timing. The changes are:
- Disable ODT on read (JEDEC standard JESD79-3F says in chapter
5.2.3 ODT during Reads: "As the DDR3 SDRAM can not terminate
and drive at the same time, RTT must be disabled at least half
a clock cycle..." and also MX7D SABRESD is disabling it)
This alone fixed memory issues for two Colibri iMX7 1GB modules
which showed issues before
- Make sure tRFC(min) is at least 260ns
- Make sure tRC is >50.625ns
- tRP needs to be >13.125ns, we can lower from 18.75ns to 15ns
- tFAW is not relevant, leave at reset
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Jon Nettleton [Mon, 25 Jun 2018 10:39:03 +0000 (13:39 +0300)]
mx6cuboxi: Move the default environment for all devices
Previously we had stored the environment right after the
u-boot.img on the disk. I never liked this because with dtbs
being included and such the image could grow in size. Instead
we move the environment to be negatively offset from the 1MB
mark. Almost all our images start at 4MB's, and most standard
images start at 1MB, and all our storage devices are a minimum
1MB. Therefore we can store env there for all classes of devices
and have plenty of space in case u-boot.img needs to grow.
Stefan Agner [Sun, 24 Jun 2018 19:09:58 +0000 (21:09 +0200)]
imx: mx7: psci: implement MIGRATE_INFO_TYPE
Implement MIGRATE_INFO_TYPE. This informs Linux that no migration
for the trusted operating system is necessary:
[ 0.000000] psci: Trusted OS migration not required
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Stefan Agner [Sun, 24 Jun 2018 19:09:57 +0000 (21:09 +0200)]
imx: mx7: psci: support CPU0 on/off
So far psci_cpu_(on|off) only worked for CPU1. Allow to control
CPU0 too. This allows to run the Linux PSCI checker successfully:
[ 2.213447] psci_checker: PSCI checker started using 2 CPUs
[ 2.219107] psci_checker: Starting hotplug tests
[ 2.223859] psci_checker: Trying to turn off and on again all CPUs
[ 2.267191] IRQ21 no longer affine to CPU0
[ 2.293266] Retrying again to check for CPU kill
[ 2.302269] CPU0 killed.
[ 2.311648] psci_checker: Trying to turn off and on again group 0 (CPUs 0-1)
[ 2.354354] IRQ21 no longer affine to CPU0
[ 2.383222] Retrying again to check for CPU kill
[ 2.392148] CPU0 killed.
[ 2.398063] psci_checker: Hotplug tests passed OK
[ 2.402910] psci_checker: Starting suspend tests (10 cycles per state)
[ 2.410019] psci_checker: cpuidle not available on CPU 0, ignoring
[ 2.416452] psci_checker: cpuidle not available on CPU 1, ignoring
[ 2.422757] psci_checker: Could not start suspend tests on any CPU
[ 2.429370] psci_checker: PSCI checker completed
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Stefan Agner [Sun, 24 Jun 2018 19:09:56 +0000 (21:09 +0200)]
imx: mx7: psci: provide complete PSCI 1.0 implementation
PSCI 1.0 require PSCI_VERSION, PSCI_FEATURES, AFFINITY_INFO and
CPU_SUSPEND to be implemented. Commit 0ec3d98f7692 ("mx7_common:
use psci 1.0 instead of 0.1") marked the i.MX 7 implementation to
be PSCI 1.0 compliant but failed to implement those functions.
Especially the missing PSCI version callback was noticeable when
booting Linux:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv65535.65535 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
This patch provides a minimal implementation thereof. With this
patch applied Linux detects PSCI 1.0:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
Fixes: 0ec3d98f7692 ("mx7_common: use psci 1.0 instead of 0.1") Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Stefan Agner [Sun, 24 Jun 2018 19:09:54 +0000 (21:09 +0200)]
ARM: PSCI: initialize stack pointer on secondary CPUs
A proper stack is required to safely use C code in psci_arch_cpu_entry.
Fixes: 486daaa618e1 ("arm: psci: add a weak function psci_arch_cpu_entry") Cc: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Patrick DELAUNAY <Patrick.delaunay@st.com> Tested-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
This function can be used only for some of the nxp SoC. Make
it explicit in the comment. This adjust a bit commit 3aa4b703b483f165dd ("imx: imx6: Move gpr_init() function to soc.c")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Fabio Estevam [Fri, 22 Jun 2018 16:54:55 +0000 (13:54 -0300)]
mx7: Remove BMODE support
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Jon Nettleton [Mon, 11 Jun 2018 12:26:23 +0000 (15:26 +0300)]
mx6cuboxi: Add emmc device tree suffix
Mainline and now the SolidRun 4.9 nxp based tree use the new
reorganization of device-tree files that separate out the emmc
into its own dtb. u-boot will now look for -emmc in the device
tree name if one is detected.
Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Jon Nettleton [Mon, 11 Jun 2018 12:26:22 +0000 (15:26 +0300)]
mx6cuboxi: Use mmc_get_op_cond() to check for an eMMC
Previously we had just made broad assumptions with which of our
boards had an eMMC or not even though this is a manufacturing time
assembly option. This takes the guessing away and actually checks for
the existence of an eMMC and sets up the has_emmc environment variable.
Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Jon Nettleton [Mon, 11 Jun 2018 12:26:19 +0000 (15:26 +0300)]
mmc: break out get_op_cond code to its own function
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Baruch Siach [Mon, 11 Jun 2018 12:26:18 +0000 (15:26 +0300)]
mmc: drop mention of IN_PROGRESS status
The IN_PROGRESS macro has been removed in commit bd47c13583f (mmc: Fix
splitting device initialization). Remove it from the mmc_start_init()
function description.
Stefan Agner [Wed, 30 May 2018 17:01:45 +0000 (19:01 +0200)]
imx: add macro to detect whether USB has been initialized
This macro allows to detect whether the boot ROM initialized USB
already (serial downloader). This is helpful to reliably detect
if the system has been recovered via USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Adam Ford [Tue, 10 Jul 2018 11:47:33 +0000 (06:47 -0500)]
configs: Convert CONFIG_USE_NAND to CONFIG_NAND
The DA850-EVM and OMAPL138_LCDK both use checks for CONFIG_USE_NAND.
This patch changes these checks to CONFIG_NAND which is already defined
in Kconfig. Since the OMAPL138_LCDK already had CONFIG_NAND defined in its
defconfig, it can be deleted from configs/omapl138_lcdk.h.
Adam Ford [Sun, 8 Jul 2018 12:28:10 +0000 (07:28 -0500)]
configs: Make NAND_BOOT and ONENAND_BOOT imply NAND
Some boards indicate support from booting NAND or
ONENAND booting, but don't enable the CONFIG_NAND. This
makes those boards imply NAND which will make
enabling other flags that are dependent on CONFIG_NAND
possible and easier to migrate.
York Sun [Tue, 26 Jun 2018 17:03:22 +0000 (10:03 -0700)]
env: Simplify Makefile using $(SPL_TPL_)
Add Kconfig options SPL_ENV_* and TPL_ENV_* and simplify Makefile.
This allows SPL/TPL image has different environment setting from
full feature U-Boot.
Klaus Goger [Fri, 25 May 2018 21:45:05 +0000 (23:45 +0200)]
rockchip: utilize CONFIG_DEFAULT_FDT_FILE
Currently the fdtfile environment variable is set to
CONFIG_DEFAULT_DEVICE_TREE which is іnternally used as U-Boot devicetree
source. The OS can use a different filename and Kconfig gives us the
ability to select a default devicetree via CONFIG_DEFAULT_FDT_FILE.
This also gives user configuring U-Boot via menuconfig the behaviour
someone would expect.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Tested-By: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Carlo Caione [Mon, 11 Jun 2018 19:00:50 +0000 (20:00 +0100)]
rockchip: veyron: Set vcc33_sd regulator value
On the veyron board the vcc33_sd regulator is used as vmmc-supply for
the SD card. This regulator is powered in the MMC core during power on
but its value is never actually set.
In the veyron platform the reset value for the LDO output is 1.8V while
the standard (min and max) value for this regulator defined in the DTS
is 3.3V. When the MMC core enable the regulator without setting its
value, the output is automatically set to 1.8V instead of 3.3V.
With this patch we preemptively set the value to 3.3V.
Signed-off-by: Carlo Caione <carlo@endlessm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Carlo Caione [Mon, 11 Jun 2018 19:00:49 +0000 (20:00 +0100)]
rk3288: Disable JTAG function from sdmmc0 IO
The GRF_SOC_CON0.grf_force_jtag bit is automatically set at boot and it
is preventing the SDMMC to work correctly. Disable the JTAG function on
the assumption that a working SD has higher priority over JTAG.
Signed-off-by: Carlo Caione <carlo@endlessm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Carlo Caione [Mon, 11 Jun 2018 19:00:48 +0000 (20:00 +0100)]
rk3288: veyron: Init boot-on regulators
Use regulators_enable_boot_on() to init all the regulators with
regulator-boot-on property.
Signed-off-by: Carlo Caione <carlo@endlessm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot.git / log