Andrew F. Davis [Thu, 7 Nov 2019 13:06:09 +0000 (08:06 -0500)]
configs: j721e_evm_r5_defconfig: Remove SPL multi-DTB FIT support
The SPL FIT will only have one DTB, so remove support for multi-DTB. This
also removes an early access to EEPROM used to select the DTB that is not
valid in SPL at the point at which it is accessed, that always returns
false for GP devices and causes a firewall expection on HS.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Adam Ford [Mon, 4 Nov 2019 23:05:24 +0000 (17:05 -0600)]
Kconfig: ti: Make board detect EEPROM addresses depend BOARD_DETECT
There is an option to enable the board detection for TI platforms.
If this is option is not set, there is no reason to set the EEPROM
bus address or chip address.
This patch makes both EEPROM_BUS_ADDRESS and EEPROM_CHIP_ADDRESS
depend on TI_I2C_BOARD_DETECT.
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Tero Kristo [Thu, 24 Oct 2019 09:30:57 +0000 (15:00 +0530)]
arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in supplies
Link the vdd-supplies for the voltage domains under the VTM node. Also,
enable the node under SPL. This will enable the AVS class 0 support on
am65x-evm board.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
Tero Kristo [Thu, 24 Oct 2019 09:30:56 +0000 (15:00 +0530)]
arm: dts: k3-am654-r5-base-board: add supply rail for MPU
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached
to i2c0 bus. Add device node for this so that it can be controlled via
a regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
Keerthy [Thu, 24 Oct 2019 09:30:54 +0000 (15:00 +0530)]
arm: dts: k3-am654-r5-base-board: Add VTM node
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
Tero Kristo [Thu, 24 Oct 2019 09:30:48 +0000 (15:00 +0530)]
power: regulator: tps6236x: add support for tps6236x regulators
TPS6236x is a family of step down DC-DC converters optimized for battery
powered portable applications for a small solution size. Add a regulator
driver for supporting these devices.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
Tero Kristo [Thu, 24 Oct 2019 09:30:46 +0000 (15:00 +0530)]
misc: k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize
the operating voltage based on characterization data written to efuse
during production. Add a driver to support this feature for K3 line of
SoCs, initially for AM65x.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
Tom Rini [Wed, 30 Oct 2019 13:18:43 +0000 (09:18 -0400)]
common/console.c: Fix unused warning with console_doenv()
Newer versions of LLVM-7 will provide an unused function warning over
console_doenv() in the case of SYS_CONSOLE_IS_IN_ENV not being enabled
as can be the case in SPL. Add guards around this function.
Heiko Schocher [Fri, 25 Oct 2019 12:46:54 +0000 (14:46 +0200)]
Makefile: fix dependency for imx targets
imx targets are defined in arch/arm/mach-imx/Makefile.
Some of them are dependent on targets defined in main
Makefile. For the Makefile in arch/arm/mach-imx this
targets must be finished before the imx targets are
build, if not you get for example the error:
make -f /home/hs/abb/mainlining/u-boot/scripts/Makefile.build obj=arch/arm/mach-imx u-boot-dtb.imx
make[2]: *** No rule to make target 'u-boot-fit-dtb.bin', needed by 'u-boot-dtb.imx'. Stop.
make[1]: *** [/home/hs/abb/mainlining/u-boot/Makefile:1123: u-boot-dtb.imx] Error 2
make[1]: *** Waiting for unfinished jobs....
make[1]: Leaving directory '/work/hs/compile/u-boot/aristainetos2_defconfig'
make: *** [Makefile:148: sub-make] Error 2
compile failed
In above case of CONFIG_MULTI_DTB_FIT is defined, the
u-boot-dtb.imx is dependent on the u-boot-fit-dtb.bin
which may is not build yet ...
I could reproduce this error on a travis build also if
I build an out-of-tree build on a local machine with a
build directory on a "slow" slow storage device. If
building the same source target with a build dir on a
fast storage device, the build works.
I found no solution to tell the arch/arm/mach-imx/Makefile
to find the targets in main Makefile, if there is a way
this would be the better fix.
I solved it by adding a IMX_DEPS var, which holds a list
of main u-boot targets, which must be finished, before
calling imx targets and fixed the build for imx
targets which enabled CONFIG_MULTI_DTB_FIT.
I think it is just luck, that imx targets with
CONFIG_OF_SEPARATE enabled build, because the
u-boot-dtb.imx target depends on u-boot-dtb.bin
which gets build early enough before starting with
u-boot-dtb.imx. May this targets should be fixed too.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Wed, 16 Oct 2019 03:55:47 +0000 (05:55 +0200)]
mpc85xx: add socrates dts from linux
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Heiko Schocher [Mon, 14 Oct 2019 09:29:39 +0000 (11:29 +0200)]
pci: add DM based mpc85xx driver
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Tom Rini [Tue, 5 Nov 2019 15:44:16 +0000 (10:44 -0500)]
travis: Rework how we write the ~/.buildman file
With python3 we're now tripping over a long-standing problem with how we
add to the buildman file with some toolchains. We cannot have multiple
toolchain-alias sections as that leads to a parse error.
Tom Rini [Tue, 5 Nov 2019 12:59:28 +0000 (07:59 -0500)]
Merge tag 'fdt-pull-5nov19' of git://git.denx.de/u-boot-fdt
Update to latest libfdt and pylibfdt, with added size control
Update binman, dtoc, patman, buildman to Python 3
Update move_config, rkmux, microcode_tool to Python 3
Peng Fan [Mon, 4 Nov 2019 09:14:15 +0000 (17:14 +0800)]
mmc: fsl_esdhc_imx: drop redundant clock settings
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Yangbo Lu [Thu, 31 Oct 2019 10:54:23 +0000 (18:54 +0800)]
mmc: fsl_esdhc: convert to use fsl_esdhc_get_cfg_common()
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Yangbo Lu [Thu, 31 Oct 2019 10:54:22 +0000 (18:54 +0800)]
mmc: fsl_esdhc: clean up bus width configuration code
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Yangbo Lu [Thu, 31 Oct 2019 10:54:21 +0000 (18:54 +0800)]
mmc: fsl_esdhc: fix voltage validation
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Yangbo Lu [Thu, 31 Oct 2019 10:54:20 +0000 (18:54 +0800)]
mmc: fsl_esdhc: drop controller initialization in fsl_esdhc_init()
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Simon Glass [Thu, 31 Oct 2019 13:43:02 +0000 (07:43 -0600)]
binman: Remember the pre-reset entry size
When preparing to possible expand or contract an entry we reset the size
to the original value from the binman device-tree definition, which is
often None.
This causes binman to forget the original size of the entry. Remember this
so that it can be used when needed.
Simon Glass [Thu, 31 Oct 2019 13:42:50 +0000 (07:42 -0600)]
patman: Adjust 'command' to return strings instead of bytes
At present all the 'command' methods return bytes. Most of the time we
actually want strings, so change this. We still need to keep the internal
representation as bytes since otherwise unicode strings might break over
a read() boundary (e.g. 4KB), causing errors. But we can convert the end
result to strings.
Add a 'binary' parameter to cover the few cases where bytes are needed.
Simon Glass [Sun, 27 Oct 2019 15:47:41 +0000 (09:47 -0600)]
mx6: tbs2910: Minimise libfdt code size
This board appears to be very near its size limit and cannot accept the
new checking code in libfdt. Disable this code so this the board can
continue to build.
Simon Glass [Sun, 27 Oct 2019 15:47:40 +0000 (09:47 -0600)]
fdt: Add Kconfig options to control code size
For better or worse libfdt recent grew a lot of code that checks the
validity of the device tree in great detail. When using unsigned or
unverified data this makes things safer, but it does add to code size.
Add some controls to select the trade-off between safety and code size.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 27 Oct 2019 15:47:39 +0000 (09:47 -0600)]
fdt: Add INT32_MAX to kernel.h for libfdt
Unfortunately libfdt needs this value now, which is present in the
stdint.h header. That file is just a placeholder in U-Boot and these sorts
of constants appear in the linux/kernel.h header instead.
To keep libfdt happy, add INT32_MAX too.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode] Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
Tom Rini [Sat, 2 Nov 2019 18:43:06 +0000 (14:43 -0400)]
tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.
Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:46 +0000 (16:49 +0100)]
imx: nandbcb: add support for writing BCB only
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:43 +0000 (16:49 +0100)]
nand: mxs_nand: add API for switching different BCH layouts
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:42 +0000 (16:49 +0100)]
imx: gpmi: add defines for hw randominizer
Extend GPMI Integrated ECC Control Register Description, include
additional defines for enabling randomizer function and providing
proper randomizer type.
For additional details check i.MX7 APR, section
9.6.6.3 GPMI Integrated ECC Control Register Description
(GPMI_ECCCTRLn)
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tom Rini [Sun, 3 Nov 2019 12:41:12 +0000 (07:41 -0500)]
tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
Ye Li [Sat, 26 Oct 2019 14:24:03 +0000 (16:24 +0200)]
mach-imx: Adding new argument for SIP call interface
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build] Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 25 Sep 2019 08:11:14 +0000 (08:11 +0000)]
imx8: Add AHAB secure boot support
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 16 Oct 2019 10:24:39 +0000 (10:24 +0000)]
imx8m: evk: spl: probe clk in spl early stage
We are going to add i2c pmic support before dram could be used.
So we need enable clk driver earlier, so use spl_early_init
and move clock controller probe eariler to board_init_f.
projects / u-boot.git / log