Kever Yang [Mon, 22 Jul 2019 12:02:14 +0000 (20:02 +0800)]
rockchip: rk3288: Move rk3288_detect_reset_reason to soc file
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 22 Jul 2019 12:02:01 +0000 (20:02 +0800)]
rockchip: add common board file for U-Boot proper
Add common board file for Rockchip SoCs to avoid too much
copy-paste work for different SoCs.
This board file in charge for common board_init() and board_late_init()
in U-Boot proper.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 22 Jul 2019 12:01:59 +0000 (20:01 +0800)]
rockchip: convert to use ROCKCHIP_BOOT_MODE_REG for fastboot tag
The fastboot_set_reboot_flag() update a TAG into a register
for next boot, use the common macro for the register so that
we can re-use the function for different SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 22 Jul 2019 11:59:24 +0000 (19:59 +0800)]
rockchip: rk3288: move setup_led() to firefly-rk3288
Only firefly-rk3288 has the dts node "u-boot,boot-led",
while CONFIG_SPL_LED is not enable, move code to firefly-rk3288
now in case someone need this code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update to fix warning:
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/optee@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /configurations/conf@1
has a unit name, but no reg property
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 22 Jul 2019 11:59:15 +0000 (19:59 +0800)]
rockchip: Migrate to use BOOTROM_SUPPORT driver
SPL bootrom support is a boot device just like mmc and etc,
use formal boot device instead of jump to bootrom directly.
Enable the Kconfig by default if ROCKCHIP_BACK_TO_BROM is enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 22 Jul 2019 11:59:12 +0000 (19:59 +0800)]
rockchip: add common spl board file
The common spl board file handles board_init_f() in SPL,
and with board_early_init_f() and arch_cpu_init() callback,
other operateion after board_init_f() should go to board specific
spl_board_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
include: configs: Increase CONFIG_SYS_BOOTM_LEN to 16MB
The default value of CONFIG_SYS_BOOTM_LEN is 0x800000 i.e, 8MB which
causes board reset because of larger uImage size.
This was tested on rk3288 Amarula Vyasa and rk3288 Asus Tinker
boards.
Error log snippet:
Booting using the fdt blob at 0x1f00000
Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sekhar Nori [Thu, 11 Jul 2019 09:00:24 +0000 (14:30 +0530)]
clk: initialize clk->data when using default xlate
Right now when using clk_of_xlate_default(), clk->data
remains un-initialized because clk_get_bulk() does not
initialize memory on allocation of clock structure.
This can cause problems when data is used to match if
two clocks pointers are exactly the same underlying
clocks, for example.
Fix it by initializing clk->data to 0.
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Masahiro Yamada [Thu, 27 Jun 2019 07:39:57 +0000 (16:39 +0900)]
fdt: make fdt_get_base_address() return OF_BAD_ADDR when "reg" not found
Currently, fdt_get_base_address() returns 0 if the "reg" property is
missing. Since 0 is a valid value, it is not suitable for the error
handling. Return OF_BAD_ADDR instead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 8 Jul 2019 20:25:53 +0000 (14:25 -0600)]
binman: Add a test for nested and aligned sections
Current test coverage is likely sufficient for the logic used to place
sections in the image. However it seems useful to add a test specifically
for nested sections, since these could have some unusual interactions.
Add a new test for this and aligned sections. This test failed before the
refactor to drop the bsection.py file (Section class), but passes now.
Simon Glass [Mon, 8 Jul 2019 20:25:51 +0000 (14:25 -0600)]
binman: Support reading from CBFS entries
CBFS is a bit like a section but with a custom format. Provide the list of
entries and the compression type to binman so that it can extract the data
from the CBFS, just like any other part of the image.
Simon Glass [Mon, 8 Jul 2019 20:25:50 +0000 (14:25 -0600)]
binman: Allow reading an entry from an image
It is useful to be able to extract entry contents from an image to see
what is inside. Add a simple function to read the contents of an entry,
decompressing it by default.
Simon Glass [Mon, 8 Jul 2019 20:25:49 +0000 (14:25 -0600)]
binman: Allow for logging information to be displayed
Binman generally operates silently but in some cases it is useful to see
what Binman is actually doing at each step. Enable some logging output
with different logging levels selectable via the -v flag.
Simon Glass [Mon, 8 Jul 2019 20:25:47 +0000 (14:25 -0600)]
binman: Convert Image to a subclass of Entry
When support for sections (and thus hierarchical images) was added to
binman, the decision was made to create a new Section class which could
be used by both Image and an Entry_section class. The decision between
using inheritance and composition was tricky to make, but in the end it
was decided that Image was different enough from Entry that it made sense
to put the implementation of sections in an entirely separate class. It
also has the advantage that core Image code does have to rely on an entry
class in the etype directory.
This work was mostly completed in commit:
8f1da50ccc "binman: Refactor much of the image code into 'section'
As a result of this, the Section class has its own version of things like
offset and size and these must be kept in sync with the parent
Entry_section class in some cases.
In the last year it has become apparent that the cost of keeping things in
sync is larger than expected, since more and more code wants to access
these properties.
An alternative approach, previously considered and rejected, now seems
better.
Adjust Image to be a subclass of Entry_section. Move the code from Section
(in bsection.py) to Entry_section and delete Section. Update all tests
accordingly.
This requires substantial changes to Image. Overall the changes reduce
code size by about 240 lines. While much of that is just boilerplate from
Section, there are quite a few functions in Entry_section which now do not
need to be overiden from Entry. This suggests the change is beneficial
even without further functionality being added.
A side benefit is that the properties of sections are now consistent with
other entries. This fixes a problem in testListCmd() where some properties
are missing for sections.
Unfortunately this is a very large commit since it is not feasible to do
the migration piecemeal. Given the substantial tests available and the
100% code coverage of binman, we should be able to do this safely.
Simon Glass [Mon, 8 Jul 2019 20:25:46 +0000 (14:25 -0600)]
binman: Support reading an image into an Image object
It is possible to read an Image, locate its FDT map and then read it into
the binman data structures. This allows full access to the entries that
were written to the image. Add support for this.
Simon Glass [Mon, 8 Jul 2019 20:25:43 +0000 (14:25 -0600)]
binman: Allow listing the entries in an image
It is useful to be able to summarise all the entries in an image, e.g. to
display this to this user. Add a new ListEntries() method to Entry, and
set up a way to call it through the Image class.
Simon Glass [Mon, 8 Jul 2019 20:25:40 +0000 (14:25 -0600)]
binman: Use the cbfs memlen field only for uncompressed length
The purpose of this badly named field is a bit ambiguous. Adjust the code
to use it only to store the uncompressed length of a file, leaving it set
to None if there is no compression used. This makes it easy to see if the
value in this field is relevant / useful.
Also set data_len for compressed fields, since it should be the length of
the compressed data, not the uncompressed data.
Simon Glass [Mon, 8 Jul 2019 20:25:39 +0000 (14:25 -0600)]
binman: Provide the actual data address for cbfs files
At present a file with no explicit CBFS offset is placed in the next
available location but there is no way to find out where it ended up.
Update and rename the get_data() function to provide this information.
Simon Glass [Mon, 8 Jul 2019 20:25:36 +0000 (14:25 -0600)]
binman: Add a control for post-pack entry expansion
We plan to support changing the size of entries after they have been
packed. For now it will always be enabled. But to aid testing of both
cases (in the event that we want to add a command-line flag, for example),
add a setting to control it.
Simon Glass [Mon, 8 Jul 2019 20:25:35 +0000 (14:25 -0600)]
binman: Add a return value to ProcessContentsUpdate()
At present if this function tries to update the contents such that the
size changes, it raises an error. We plan to add the ability to change
the size of entries after packing is completed, since in some cases it is
not possible to determine the size in advance.
An example of this is with a compressed device tree, where the values
of the device tree change in SetCalculatedProperties() or
ProcessEntryContents(). While the device tree itself does not change size,
since placeholders for any new properties have already bee added by
AddMissingProperties(), we cannot predict the size of the device tree
after compression. If a value changes from 0 to 0x1234 (say), then the
compressed device tree may expand.
As a first step towards supporting this, make ProcessContentsUpdate()
return a value indicating whether the content size is OK. For now this is
always True (since otherwise binman raises an error), but later patches
will adjust this.
Simon Glass [Mon, 8 Jul 2019 20:25:34 +0000 (14:25 -0600)]
binman: Call ProcessUpdateContents() consistently
SetContents() should only be called to set the contents of an entry from
within the ObtainContents() call, since it has no guard against increasing
the size of the contents, thus triggering incorrect operation.
Change all such calls to use ProcessUpdateContents() instead.
Simon Glass [Mon, 8 Jul 2019 20:25:33 +0000 (14:25 -0600)]
binman: Fix up ProcessUpdateContents error and comments
This function raises an exception with its arguments around the wrong way
so the message is incorrect. Fix this as well as a few minor comment
problems.
Simon Glass [Mon, 8 Jul 2019 20:25:32 +0000 (14:25 -0600)]
binman: Allow easy importing of entry modules
At present entry modules can only be accessed using Entry.Lookup() or
Entry.Create(). Most of the time this is fine, but sometimes a module
needs to provide constants or helper functions useful to other modules.
It is easier in this case to use 'import'.
Simon Glass [Mon, 8 Jul 2019 20:25:30 +0000 (14:25 -0600)]
binman: Move compression into the Entry base class
Compression is currently available only with blobs. However we want to
report the compression algorithm and uncompressed size for all entries,
so that other entry types can support compression. This will help with
the forthcoming 'list' feature which lists entries in the image.
Move the compression properties into the base class. Also fix up the docs
which had the wrong property name.
Simon Glass [Mon, 8 Jul 2019 20:25:29 +0000 (14:25 -0600)]
binman: Convert to use ArgumentParser
This class is the new way to handle arguments in Python. Convert binman
over to use it. At the same time, introduce commands so that we can
separate out the different parts of binman functionality.
Simon Glass [Mon, 8 Jul 2019 20:25:28 +0000 (14:25 -0600)]
binman: Add an image header
It is useful to be able to quickly locate the FDT map in the image. An
easy way to do this is with a pointer at the start or end of the image.
Add an 'image header' entry, which places a magic number followed by a
pointer to the FDT map. This can be located at the start or end of the
image, or at a chosen location.
As part of this, update GetSiblingImagePos() to detect missing siblings.
Simon Glass [Mon, 8 Jul 2019 20:25:27 +0000 (14:25 -0600)]
binman: Add an FDT map
An FDT map is an entry which holds a full description of the image
entries, in FDT format. It can be discovered using the magic string at
its start. Tools can locate and read this entry to find out what entries
are in the image and where each entry is located.
Simon Glass [Mon, 8 Jul 2019 20:25:23 +0000 (14:25 -0600)]
binman: Simplify the entry test
The current test for the 'entry' module is a bit convoluted since it has
to import the module multiple times. It also relies on ordering, in that
test1EntryNoImportLib() must run before test2EntryImportLib() if they are
running in the same Python process.
This is unreliable since neither the ordering of tests nor the process
that they run in is defined.
Fix this by always reloading the entry in these two tests. Also add a
check that the expected value of have_importlib is obtained.
This corrects a code-coverage problem in the 'entry' module on some
systems.
Simon Glass [Mon, 8 Jul 2019 19:18:56 +0000 (13:18 -0600)]
binman: Add support for fixed-offset files in CBFS
A feature of CBFS is that it allows files to be positioned at particular
offset (as with binman in general). This is useful to support
execute-in-place (XIP) code, since this may not be relocatable.
projects / u-boot.git / log