This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mediatek: stop using bitfileds for DMA descriptors
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
net: mediatek: use a struct to cover variations of all SoCs
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tom Rini [Tue, 20 Sep 2022 12:49:36 +0000 (08:49 -0400)]
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Stefan Roese [Thu, 15 Sep 2022 14:20:43 +0000 (16:20 +0200)]
kirkwood: lsxl: Sync defconfigs
With the recent changes in the Orion timer driver Kconfig setup, the
board specific enabling is not needed any more. This patch sync's these
2 boards with their current defconfig version.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Michael Walle <michael@walle.cc> Tested-by: Tony Dinh <mibodhi@gmail.com>
Stefan Roese [Thu, 15 Sep 2022 14:20:40 +0000 (16:20 +0200)]
arm: mvebu: dts: Makefile: Compile Armada 375 dtb in a separate step
This patch changes the compilation, so that the Armada 375 board(s) are
compiled in a separate step. This is necessary for the timer dts
conversion, as A375 has a different / timer description in the dts.
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Tony Dinh <mibodhi@gmail.com>
Stefan Roese [Thu, 15 Sep 2022 14:20:39 +0000 (16:20 +0200)]
arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Tony Dinh <mibodhi@gmail.com>
Stefan Roese [Thu, 15 Sep 2022 13:21:22 +0000 (15:21 +0200)]
arm: mvebu: theadorable: Update eth & mdio DT nodes
With the recent changes in the Marvel mvneta network driver, the MDIO
bus is not connected any more. This patch updates the DT nodes to use
the nodes from the dtsi files instead of creating ad-hoc nodes.
Maximal size of u-boot kwb image binary is $CONFIG_ENV_OFFSET which is
0xF0000 = 983040 bytes. So add missing CONFIG_BOARD_SIZE_LIMIT definition
to ensure that u-boot binary does not overflow to the u-boot env storage.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tim Harvey [Thu, 8 Sep 2022 16:11:13 +0000 (09:11 -0700)]
imx8m*_venice_defconfig: fix default bootcmd
commit 970bf8603b87 ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
had an unintended side effect of resulting in a bootcmd env var change
for boards like venice that did not have CONFIG_USE_BOOTCOMMAND defined
and relied on it being defaulted in include/config_distro_bootcmd.h.
Following that patch it instead got defaulted in tools/env/fw_env_private.h
Fix this by enabling CONFIG_USE_BOOTCOMMAND for venice.
Fixes: commit 970bf8603b87 ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig") Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Marek Behún [Mon, 19 Sep 2022 09:32:08 +0000 (11:32 +0200)]
powerpc: mpc85xx: Fix incorrect application of patch
I messed up application of patch 5a428e751044 ("mmc: fsl_esdhc_spl: Add
support for builds without CONFIG_SYS_MMC_U_BOOT_OFFS"). I took it from
a work-in-progress branch where I changed usage of
CONFIG_SDCARD to CONFIG_SD_BOOT
and refactored
SYS_MPC85XX_NO_RESETVEC
mess.
But these changes aren't in master yet. Fix the wrong usage of these
macros.
Fixes: 5a428e751044 ("mmc: fsl_esdhc_spl: Add support for builds without
CONFIG_SYS_MMC_U_BOOT_OFFS") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Pali Rohár <pali@kernel.org>
pinctrl: at91-pio4: Add support for pinctrl config subnodes
Previously, in order for the `pinctrl-*` DT node properties
to be properly processed, the pinctrl's subnodes were limited
to only having the `pinmux` property as well as other additional
properties (slew-rate, bias-disable, etc.). Now, with this patch
the pinctrl driver is made to work similarly to the one from Linux.
It can now distinguish between one subnode and a subnode with multiple
subnodes.
pinctrl: at91-pio4: Bind GPIO driver to the pinctrl DT node
This has been done in order to align the DT of U-Boot with the DT
of Linux. In Linux, a phandle from a '-gpio' DT property is linked
to the pinctrl driver, a single driver that handles both pinctrl
settings and offers GPIO API to callers. On the other hand,
U-Boot redirects such phandle to a corresponding UCLASS_GPIO
driver, because U-Boot offers two different types of drivers
in this case: UCLASS_PINCTRL which handles pin functions and
UCLASS_GPIO which handles gpio requests as a gpio provider.
Due to this, we have two drivers in Uboot, but the Devicetree
has a single node. Thus, just one of the drivers can be probed
for the DT node during platform initialization, before relocation.
Our previous solution in U-Boot was to have a different devicetree:
the gpio node has a subnode for the pinctrl driver, which
is not compliant with Linux ABI. Furthermore, our documentation
for this type of nodes mentions no such gpio compatible.
After this patch, we can no longer add nodes with a gpio
compatible in the DT. Thus, in order to link the pinctrl driver to
the gpio one, a hook to the bind method of the former in U-Boot has
been added and the GPIO related compatibles have been removed to
avoid conflict when compatibles are enumerated and bound to drivers
during platform start before relocation. The bind method will attach
the GPIO driver to the pinctrl DT node so that every phandle coming
from '-gpio' DT properties will be redirected to a valid driver
attached to the pinctrl DT node.
ARM: dts: at91: sama7: Align with Linux Devicetree
This patch makes sure that the Devicetree for the sama7
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
ARM: dts: at91: sama5: Align with Linux Devicetree
This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
configs: sama9x60_curiosity: add onewire and eeprom drivers
SAM9X60 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol. Enabling one wire and eeprom drivers
for this memory.
Sergiu Moga [Wed, 22 Jun 2022 13:30:47 +0000 (16:30 +0300)]
mmc: atmel_sdhci: re-enable sdhci after SD Card re-insertion
Whenever the SD Card would be removed and then re-inserted while in the
U-Boot command line, the `SDBPWR` bit of the `SDMMC_PCR` register would
remain unset afterwards. In order for the bit to be set again after
re-insertion, register an additional `deferred_probe` method that the
DM would then transparently call. This method will call the generic
`sdhci_probe` which will, during its execution flow, set this bit to 1.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com> Reported-by: Mihai Sain <mihai.sain@microchip.com> Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Marek Vasut [Tue, 30 Aug 2022 12:34:26 +0000 (14:34 +0200)]
ARM: imx: Update Data Modul i.MX8M Mini eDM SBC DRAM timing
Adjust the DRAM timing settings for this board per ones provided
by hardware department. The change is applied to the LPDDR4 MR11
register CA ODT configuration, from RZQ/6 to RZQ/3, which fixes
stability issues on subset of boards. The DDR PHY PIE block has
been updated accordingly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
Marcel Ziswiler [Mon, 22 Aug 2022 13:06:03 +0000 (15:06 +0200)]
verdin-imx8mm: various config additions and improvements
- integrate bootcount using SNVS_LP general purpose register LPGPR0
- enable link-time optimisation
- explicitly set a boot delay of one second
- enable CRC32 and MD5
- enable command for low-level access to data in a partition
- enable time commands
- enable PMIC commands
- improve ETHPRIME configuration
- enable eMMC HS400 functionality
- enable fixed PHY and MDIO driver model
- remove stale PFUZE100 PMIC driver
- enable thermal management unit driver
- enable more USB host functionality
- enable hexdump
on imx8(mm) the RXDMUXSEL needs to be set for data going over the wire
(as observable on a connected 'scope) to actually make it into the
RXFIFO
the reference manual is not overly clear about this, and only
mentiones that "UCR3_RXDMUXSEL should always be set." - and since the
CR3 register reverts to its reset values after setting the baudrate,
setting this bit is done during '_mxc_serial_setbgr'
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus:
- loadaddr=0x48280000 allows for 128.5MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 127.5MB : allows for 127.5MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB : allows for 512KB script
Memory layout taken from commit fd5c7173ade4
("imx8m{m,n}_venice: update env memory layout") but moved loadaddr by an
additional 0.5MB to avoid "Moving Image from 0x48200000 to 0x48280000"
during booti plus actually defining kernel_comp_size to make booti work.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Marek Vasut [Fri, 19 Aug 2022 11:02:53 +0000 (13:02 +0200)]
ARM: imx: Update DDR frequency on i.MX8M Plus DHCOM
Commit 99c7cc58e12 ("ddr: imx: Add i.MX9 DDR controller driver")
contains an inobvious side-effect which renders all systems using
DRAM controller at 3732 MT/s unbootable. The change is located in
ddrphy_init_set_dfi_clk(), where the switch case statement entry
3732 changed to entry 3733, so any board with DDR calibration data
for 3732 MT/s operations needs to be updated to 3733 MT/s to match
the change.
Since there is currently only one such board, update the board instead
of handling both 3732 and 3733 options in the driver. It is likely the
NXP MX8MP RPA update will follow and use the later value too.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Marek Vasut [Fri, 19 Aug 2022 11:02:23 +0000 (13:02 +0200)]
imx8m: ddrphy_utils: Remove unused file
The ddrphy_utils.c is now deduplicated in drivers/ddr/imx/phy/ddrphy_utils.c ,
this drivers/ddr/imx/imx8m/ddrphy_utils.c is a remnant from when the
deduplication was implemented and was not removed. Remove it as it is
unused.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Fri, 12 Aug 2022 20:59:10 +0000 (22:59 +0200)]
ARM: imx: dh-imx6: Increase SF erase area for u-boot update
Erase the entire U-Boot area during U-Boot update instead of just
a subset of it. This way, in case u-boot-with-spl.imx grows, the
sf write won't write over non-erased part of the SPI NOR.
Marek Vasut [Fri, 12 Aug 2022 20:41:49 +0000 (22:41 +0200)]
ARM: imx: Enable USB ethernet on i.MX8M Plus DHCOM
Enable both USB CDC ethernet and USB host ethernet on i.MX8M Plus DHCOM.
This is useful for bringing up systems without ethernet plug, but with
either USB host or gadget plug.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: uboot-imx <uboot-imx@nxp.com>
Tim Harvey [Thu, 11 Aug 2022 18:55:38 +0000 (11:55 -0700)]
board: gateworks: venice: add fixup for GW73xx-C+
The GW73xx-C revision and onward replaced the 5-port PCIe switch with a
4-port (dropping PCIe to one of the miniPCIe sockets) due to part
availability. This moved the PCI bus of the GbE eth1 device. Use a fixup
to adjust the dt accordingly so that local-mac-address assigned from dt
works on new revision boards.
While we are at it, rename 'blob' to 'fdt' for clarity.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Fixes: 4e5114daf9eb ("imx8mn: synchronise device tree with linux") Signed-off-by: Adam Ford <aford173@gmail.com>
Add HABv4 documentation extension for SPL targets covering the
following topics:
- How to sign an securely boot an flash.bin container image.
- How to extend the root of trust for additional boot images.
- Add SPL and fitImage CSF examples.
- Add signature generation script example.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Breno Lima <breno.lima@nxp.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com> Cc: Ye Li <ye.li@nxp.com>
The i.MXRT11 series has two new pll types but are variants of existing.
This patch adds the ability to read one of the pll types' frequency
as it can't be changed unlike the generic pll it also has the
division factors swapped.
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Stefan Roese [Thu, 15 Sep 2022 14:20:36 +0000 (16:20 +0200)]
timer: orion-timer: Use timer_conv_64() to fix timer wrap around
While testing on some Kirkwood platforms it was noticed that the timer
did not function correctly all the time. The driver did not correctly
handle 32bit timer value wrap arounds. Using the timer_conv_64()
conversion function fixes this issue.
Fixes: e9e73d78a8fb ("timer: add orion-timer support") Suggested-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com> Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Tony Dinh <mibodhi@gmail.com>
Marek Behún [Tue, 13 Sep 2022 16:10:28 +0000 (18:10 +0200)]
arm: mvebu: turris_omnia: Fix setting switch CONFIG pins on new board design
It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 2 Sep 2022 12:10:47 +0000 (14:10 +0200)]
watchdog: Get rid of ASSEMBLY hacks
Only one occurance of WATCHDOG_RESET is left in one assembler file.
This patch changes this occurance to a direct call to watchdog_reset
and then removes all the ASSEMBLY ifdef'ery in watchdog.h, as it's not
needed any more to clean this mess a bit up.
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Stefan Roese [Fri, 2 Sep 2022 12:10:45 +0000 (14:10 +0200)]
cyclic: Introduce schedule() function
This patch introduces a schedule() function, which shall be used instead
of the old WATCHDOG_RESET. Follow-up patches will make sure, that this
new function is used.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Stefan Roese [Thu, 18 Aug 2022 11:22:46 +0000 (13:22 +0200)]
watchdog: Integrate watchdog triggering into the cyclic framework
This patch integrates the watchdog triggering into the recently added
cyclic infrastructure. Each watchdog device that shall be triggered
registers it's own cyclic function. This way, multiple watchdog devices
are still supported, each via a cyclic function with separate trigger
intervals.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Tom Rini [Fri, 16 Sep 2022 19:35:47 +0000 (15:35 -0400)]
Merge branch '2022-09-16-rationalize-the-block-interface' into next
The block interface has two separate implementations, one using driver
model and one not. The latter is really only needed for SPL, where
size constraints allegedly don't allow use of driver model. Of course
we still need space for filesystems and other code, so it isn't clear
that driver model is anything more than the straw that breaks the
camel's back.
The driver model version uses a uclass ID for the interface time, but
converts back and forth between that and if_type, which is the legacy
type.
The HAVE_BLOCK_DEVICE define is mostly a hangover from the old days.
At present its main purpose is to enable the legacy block implementation
in SPL.
Finally the use of 'select' to enable BLK does not work very well. It
causes kconfig errors when another option depends on BLK and it is
not recommended by the kconfig style guide.
This series aims to clean things up:
- Enable BLK based on whether different media types are used, but still
allow boards to disable it
- Rename HAVE_BLOCK_DEVICE to indicates its real purpose
- Drop if_type and use the uclass instead
- Drop some obsolete if_type values
An issue not resolved by this series is that the sandbox host interface
does not actually have a device. At present it uses the root device, which
was convenience for the driver model conversion but not really correct. It
should be possible to clean this up, in a future series.
Another minor issue is the use of UCLASS_USB for a mass-storage device.
This has been the case for a while and is not addresed by this series,
other than to add a comment.
Note that this test relies on Tom Rini's series to drop various boards
including warp and cm_t335
Finally, a patch is included to make binman put fake files in a
subdirectory, since repeated runs of certain boards can cause unrelated
failues (e.g. chromebook_coral) when fake files are left around.
Pali Rohár [Fri, 5 Aug 2022 20:09:41 +0000 (22:09 +0200)]
mmc: fsl_esdhc_spl: Add support for builds without CONFIG_SYS_MMC_U_BOOT_OFFS
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Pali Rohár [Fri, 5 Aug 2022 20:09:40 +0000 (22:09 +0200)]
powerpc: mpc85xx: Fix loading U-Boot proper from SD card in SPL
Change 8-byte alignment of SPL binary to just 4-byte alignment as objcopy
trims trailing zero bytes when converting ELF file to RAW binary.
This is same fix for SPL linker script as was done fix for U-Boot linker
script in commit e8c0e0064c8a ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE
support").
It is required for the patch "mmc: fsl_esdhc_spl: Add support for builds
without CONFIG_SYS_MMC_U_BOOT_OFFS" which triggered this issue in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org>
Marek Behún [Thu, 15 Sep 2022 14:08:27 +0000 (16:08 +0200)]
powerpc: mpc85xx: Fix check for CONFIG_SDCARD
Commit d433c74eecdc ("Convert CONFIG_SDCARD et al to Kconfig") converted
SYS_EXTRA_OPTIONS=SDCARD or SPIFLASH to config options CONFIG_SDCARD and
CONFIG_SPIFLASH, but left one occurance unchanged.
Fix this.
Fixes: d433c74eecdc ("Convert CONFIG_SDCARD et al to Kconfig") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Wed, 3 Aug 2022 21:56:55 +0000 (23:56 +0200)]
Makefile: Unify condition for mpc85xx reset vector
Use 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && CONFIG_OF_SEPARATE' pattern
instead of 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && !CONFIG_OF_EMBED' also in
OBJCOPYFLAGS_u-boot-nodtb.bin as this pattern is used in rest of Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Behún <kabel@kernel.org>
Pali Rohár [Wed, 3 Aug 2022 11:24:42 +0000 (13:24 +0200)]
Makefile: Reduce usage of custom mpc85xx u-boot.bin target
Building of final u-boot.bin binary for mpc85xx via binman is needed only
when inserting DTB binary in the middle of the u-boot ELF binary (before
.bootpg and .resetvec ELF sections).
These requirements are met when CONFIG_MPC85XX_HAVE_RESET_VECTOR is enabled
(= generating .bootpg/.resetvec sections) and CONFIG_OF_SEPARATE is enabled
(= inserting DTB binary).
So in all other cases use standard build procedure instead of custom
mpc85xx u-boot.bin Makefile target via binman.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org>
Pali Rohár [Mon, 1 Aug 2022 15:42:20 +0000 (17:42 +0200)]
Makefile: Build final mpc85xx non-SPL image in standard file u-boot.bin
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Behún <kabel@kernel.org>
Pali Rohár [Mon, 1 Aug 2022 15:42:19 +0000 (17:42 +0200)]
Makefile: Fix dependency for u-boot-with-dtb.bin
Makefile uses binman to produce u-boot-with-dtb.bin target. As its input it
takes DTB file and u-boot binary without DTB, which is stored in file
u-boot-nodtb.bin. So fix target dependency.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Behún <kabel@kernel.org>
Simon Glass [Fri, 12 Aug 2022 01:34:58 +0000 (19:34 -0600)]
efi: Correct assumption about if_type
efi_set_blk_dev_to_system_partition() assumes that 0 is an invalid
if_type. This is true now but is about to be false. Fix this bug to avoid
a test failure.
projects / u-boot.git / log