Thomas Hebb [Fri, 15 Nov 2019 16:48:55 +0000 (08:48 -0800)]
rockchip: SPL: fix ordering of DRAM init
The common SPL code reordered the DRAM initialization before
rockchip_stimer_init(), which as far as I can tell causes the RK3399 to
lock up completely.
Fix this issue in the common code by putting the DRAM init back after
timer init. I have only tested this on the RK3399, but it wouldn't make
any sense for the timer init to require DRAM be set up on any system.
Fixes: b7abef2ecbcc ("rockchip: rk3399: Migrate to use common spl board file") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Thu, 14 Nov 2019 03:21:12 +0000 (11:21 +0800)]
arm: rockchip: Add RK3308 SOC support
RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peter Robinson [Sat, 9 Nov 2019 20:30:05 +0000 (20:30 +0000)]
rockchip: dts: rk3399: move the u-boot, dm-pre-reloc to the u-boot.dtsi
The u-boot specific pieces in the dts files should be in u-boot.dtsi
not the main files, this allows easier sync with upstream. The
rk3399.dtsi has a mix of both so move them all for consistency.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix with missing pmugrf) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: rk3399: split rockpro64 out of evb_rk3399
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_IS_ENABLED() needs the config name like used in Kconfig, so
without the leading CONFIG_. The clock drivers all wrongly check for
CONFIG_RESET_ROCKCHIP, fix that
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Soeren Moch [Thu, 7 Nov 2019 11:11:22 +0000 (12:11 +0100)]
arm: dts: rk3399-rockpro64: slightly increase center voltage
The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage
scaling. So the regulator reset voltage of 0.9V is used on this board.
Let u-boot initialize the center voltage to 0.95V as it is done for the
VD_LOGIC domain. This avoids instability and occasional linux kernel
Opses on this board.
Signed-off-by: Soeren Moch <smoch@web.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add core architecture code to support the px30 soc.
This includes a separate tpl board file due to very limited
sram size as well as a non-dm sdram driver, as this also has
to fit into the tiny sram.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: misc: read cpuid either from efuse or otp
Newer Rockchip socs use a different ip block to handle one-time-
programmable memory, so depending on what got enabled get the cpuid
from either source.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
spl: separate SPL_FRAMEWORK config for spl and tpl
Right now enabling SPL_FRAMEWORK will also enable it for the TPL in all
cases, making the TPL bigger. There may be cases where the TPL is really
size constrained due to its underlying ram size.
Therefore introduce a new TPL_FRAMEWORK option and make the relevant
conditionals check for both. The default is set to "y if SPL_FRAMEWORK"
to mimic the previous behaviour where the TPL would always get the
SPL framework if it was enabled in SPL.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
YouMin Chen [Fri, 15 Nov 2019 03:04:53 +0000 (11:04 +0800)]
ram: rk3399: Fix dram setting to make dram more stable
There are some code different with rockchip vendor code which may lead
to different bugs, including:
1) Fix setting error about LPDDR3 dram size ODT.
2) Set phy io speed to 0x2.
3) Fix setting error about phy_pad_fdbk_drive.
4) Fix setting error about PI_WDQLVL_VREF_EN
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
YouMin Chen [Fri, 15 Nov 2019 03:04:43 +0000 (11:04 +0800)]
ram: px30: add sdram driver
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 15 Nov 2019 03:04:42 +0000 (11:04 +0800)]
ram: rockchip: add common msch reg definition
The noc register bit definition may be the same for different SoC while
the offset of the register may be different, add the struction
definition as common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 15 Nov 2019 03:04:37 +0000 (11:04 +0800)]
ram: rockchip: add common code for sdram driver
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 15 Nov 2019 03:04:35 +0000 (11:04 +0800)]
rockchip: sdram: extend to use sys_reg3 for capacity info
Since we have new DRAM type and to support different DRAM size in different
CS, we need more bits, so introduce sys_reg3 to record the info.
Note that the info in sys_reg3 is extension to sys_reg2 and the info in
sys_reg2 is the same as before. We define the DRAM_INFO with sys_reg3 as
VERSION2.
All the ENC macro are moved to sdram_common.h since the sdram.c only
need to do the info decode.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 15 Nov 2019 03:04:34 +0000 (11:04 +0800)]
rockchip: sdram: move cap structure and debug function to sdram_common.h
The sdram.h suppose to be helper file for sdram.c which including dram
size decode and some u-boot related dram init interface, and all
structure and function for dram driver move to sdram_common.h
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 15 Nov 2019 03:04:33 +0000 (11:04 +0800)]
ram: rockchip: rename sdram_common.c/h to sdram.c
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Migrate the symbol CONFIG_SYS_REDUNDAND_ENVIRONMENT to Kconfig. This
is size neutral outside of two platforms with latent bugs being fixed
now and they no longer have "ENV_IS_NOWHERE" set along with their
intended location.
With recent update in u-boot gitattributes all files are treated as regular
text files. This creates problems with special files and repo always
shows uncommitted files like below.
Your branch is up-to-date with 'origin/master'.
Changes not staged for commit:
(use "git add <file>..." to update what will be committed)
(use "git checkout -- <file>..." to discard changes in working directory)
Simon Glass [Thu, 7 Nov 2019 00:22:44 +0000 (17:22 -0700)]
binman: tegra: Adjust symbol calculation depending on end-at-4gb
A recent change adjusted the symbol calculation to work on x86 but broke
it for Tegra. In fact this is because they have different needs.
On x86 devices the code is linked to a ROM address and the end-at-4gb
property is used for the image. In this case there is no need to add the
base address of the image, since the base address is already built into
the offset and image-pos properties.
On other devices we must add the base address since the offsets start at
zero.
In addition the base address is currently added to the 'offset' and 'size'
values. It should in fact only be added to 'image-pos', since 'offset' is
relative to its parent and 'size' is not actually an address. This code
should have been adjusted when support for 'image-pos' and 'size' was
added, but it was not.
To correct these problems:
- move the code that handles adding the base address to section.py, which
can check the end-at-4gb property and which property
(offset/size/image-pos) is being read
- add the base address only when needed (only for image-pos and not if the
image uses end-at-4gb)
- add a note to the documentation
- add a separate test to cover x86 behaviour
Fixes: 15c981cc (binman: Correct symbol calculation with non-zero image base) Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
Tom Rini [Mon, 11 Nov 2019 19:19:32 +0000 (14:19 -0500)]
Merge tag 'u-boot-rockchip-20191110' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Levin Du [Thu, 17 Oct 2019 07:22:38 +0000 (15:22 +0800)]
rockchip: adding the missing "/" in entries of boot_devices
Without the prefix, "same-as-spl" in `u-boot,spl-boot-order` will not work
as expected. When board_boot_order() `spl-boot-order.c` meets
"same-as-spl", it gets the conf by looking the boot_devices table by boot
source, and parse the node by the conf with:
node = fdt_path_offset(blob, conf);
which will failed without the "/" indicating the path.
Currently only entries of boot_devices in rk3399 have the "/" prefix.
Therefore add the missing ones in other boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 18 Oct 2019 07:54:16 +0000 (15:54 +0800)]
rockchip: config: update CONFIG_SPL_MAX_SIZE for 64bit CPUs
Since we move the ATF bl31 entry for 64bit CPUs to 0x40000, we need to
limit the SPL size in 0x40000(start from 0) so that we don't need to do
the relocate for ATF loading.
Note that there will be separate BSS, STACK and MALLOC heap, so the size
0x40000(256KB) should be enough for SPL text.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 18 Oct 2019 07:54:15 +0000 (15:54 +0800)]
rockchip: rk3399: update SPL_STACK_R_ADDR
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.
After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Wed, 23 Oct 2019 03:10:36 +0000 (11:10 +0800)]
rockchip: evb-px5: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since: 0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Wed, 23 Oct 2019 02:08:53 +0000 (10:08 +0800)]
rockchip: rk3328: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since: 0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 18 Oct 2019 07:54:14 +0000 (15:54 +0800)]
rockchip: rk3399: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since: 0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Joseph Chen [Sun, 6 Oct 2019 18:10:22 +0000 (20:10 +0200)]
common: spl: atf: support booting bl32 image
Trusted-Firmware can also initialize a secure payload to use as a trusted
execution environment. In general for the arm64 case this is provided as
separate image and uboot is supposed to also place it in a predetermined
location in memory and add the necessary parameters to the ATF boot params.
So add the possibility to get this tee payload from the provided FIT image
and setup things as necessary.
Tested on a Rockchip PX30 with mainline TF-A, mainline OP-Tee (with pending
PX30 support) and mainline 5.4-rc1 Linux kernel.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Sun, 6 Oct 2019 18:10:21 +0000 (20:10 +0200)]
rockchip: make_fit_atf.py: allow inclusion of a tee binary
A trusted execution environment should also get loaded as loadable from
a fit image, so add the possibility to present a tee.elf to make_fit_atf.py
that then gets included as additional loadable into the generated its.
For ease of integration the additional loadable is created as atf_(x+1)
after all others to re-use core generation loops.
Tested against the combinations of 1-part-atf and multi-part-atf each
time with and without a tee binary present.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon South [Sun, 6 Oct 2019 16:28:13 +0000 (12:28 -0400)]
ram: rk3328: Use correct frequency units in function
Fix a pair of tests in phy_dll_bypass_set() that used incorrect units
for the DDR frequency, causing the DRAM controller to be misconfigured
in most cases.
Signed-off-by: Simon South <simon@simonsouth.net> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Emmanuel Vadot [Tue, 8 Oct 2019 17:59:50 +0000 (19:59 +0200)]
rockchip: dts: rk3328: rock64: Add same-as-spl order
rk3328 can use same-as-spl option so next loaders are loaded from the same
medium.
Add the boot order in the rock64 dts otherwise booting from sdcard
will result in u-boot looking into the eMMC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Sun, 22 Sep 2019 10:06:56 +0000 (18:06 +0800)]
rockchip: rk3399: Add Leez P710 support
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Joseph Chen [Thu, 26 Sep 2019 07:45:07 +0000 (15:45 +0800)]
power: pmic: rk809: support rk809 pmic
The RK809 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(5*BUCKs, 9*LDOs, 2*SWITCHes)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Joseph Chen [Thu, 26 Sep 2019 07:44:55 +0000 (15:44 +0800)]
power: pmic: rk817: support rk817 pmic
The RK817 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1* BOOST, 9*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK805 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 3*LDOs)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK816 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1*BOOST, 6*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
power: regulator: rk8xx: update the driver for rk808 and rk818
In order to adapt the following pmics, make the interface more compatible.
Support buck and ldo suspend voltage setting and getting.
Supprot buck and ldo suspend enable/disable setting and getting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Fri, 8 Nov 2019 14:26:18 +0000 (09:26 -0500)]
tools/img2brec.sh: Delete unused tool
This script was only used on the MX1ADS board (and possibly other MX1
platforms) to program the flash. As we no longer have any boards for
that SoC, remove this tool.
Fixes: e570aca9474b ("mx1ads: remove board support") Signed-off-by: Tom Rini <trini@konsulko.com>
AKASHI Takahiro [Fri, 8 Nov 2019 01:32:15 +0000 (10:32 +0900)]
cmd: move down CONFIG_CMD_BOOTEFI after CONFIG_BOOTM_VXWORKS
Due to the commit 4b0bcfa7c4ec ("Kconfig: Migrate CONFIG_BOOTM_* options")
BOOTEFI and BOOTEFI_HELLO_COMPILE (and other BOOTEFI configs) are
displayed in a long distance. This will make it difficult for us to
understand that those configurations are closely related.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log