NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.
So macro for this micron manufacturer id.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Pankaj Bansal [Wed, 10 Oct 2018 08:38:34 +0000 (14:08 +0530)]
driver: net: fsl-mc: Add support of multiple phys for dpmac
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pankaj Bansal [Wed, 10 Oct 2018 08:38:33 +0000 (14:08 +0530)]
driver: net: fsl-mc: initialize dpmac irrespective of phy
The dpmac initalization should not depend on phy.
As the phy is not necessary to be present for dpmac to function.
Therefore, remove dpmac initialization dependency from phy.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pankaj Bansal [Wed, 10 Oct 2018 08:38:32 +0000 (14:08 +0530)]
driver: net: fsl-mc: Modify the dpmac link detection method
when there is no phy present for a dpmac, a dummy phy device is created.
when we move to multiple phy method, we need to create as many dummy phy
devices.
Change this method so that we don't need to create dummy phy devices.
We always report linkup if no phy is present.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Andrew F. Davis [Wed, 3 Oct 2018 15:03:23 +0000 (10:03 -0500)]
arm: K3: am654: Add support for getting boot mode
Read the boot mode register to find the boot mode. Only use eMMC boot0
mode when the mode is eMMC boot (called BOOT_DEVICE_MMC1 currently due
to current conflating of boot mode and boot device), and not iff the
boot device is MMC port 0.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Andrew F. Davis [Wed, 3 Oct 2018 15:03:22 +0000 (10:03 -0500)]
arm: K3: am654: Choose MMC boot device based on boot port
For most devices the boot mode maps directly to the boot
device. For MMC this is not the case as we have two MMC
boot modes and two MMC boot devices (ports). Check the
boot port to determine which MMC device was our boot
device. Make this change for both primary and secondary
boot modes.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Joe Hershberger [Wed, 26 Sep 2018 21:49:02 +0000 (16:49 -0500)]
net: Don't overwrite waiting packets with asynchronous replies
Peter originally sent a fix, but it breaks a number of other things.
This addresses the original reported issue in a different way.
That report was:
> U-Boot has 1 common buffer to send Ethernet frames, pointed to by
> net_tx_packet. When sending to an IP address without knowing the MAC
> address, U-Boot makes an ARP request (using the arp_tx_packet buffer)
> to find out the MAC address of the IP addressr. When a matching ARP
> reply is received, U-Boot continues sending the frame stored in the
> net_tx_packet buffer.
>
> However, in the mean time, if U-Boot needs to send out any network
> packets (e.g. replying ping packets or ARP requests for its own IP
> address etc.), it will use the net_tx_packet buffer to prepare the
> new packet. Thus this buffer is no longer the original packet meant
> to be transmitted after the ARP reply. The original packet will be
> lost.
This instead uses the ARP tx buffer to send async replies in the case
where we are actively waiting for an ARP reply.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Tran Tien Dat <peter.trantiendat@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Joe Hershberger [Wed, 26 Sep 2018 21:49:01 +0000 (16:49 -0500)]
test: eth: Add a test for the target being pinged
The target will respond to pings while doing other network handling.
Make sure that the response happens and is correct.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Joe Hershberger [Wed, 26 Sep 2018 21:49:00 +0000 (16:49 -0500)]
test: eth: Add a test for ARP requests
This tests that ARP requests made to this target's IP address are
responded-to by the target when it is doing other networking operations.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Joe Hershberger [Wed, 26 Sep 2018 21:48:59 +0000 (16:48 -0500)]
net: sandbox: Add a priv ptr for tests to use
Tests need to be able to pass their "unit test state" to the handlers
where asserts are evaluated. Add a function that allows the tests to set
this private data on the sandbox eth device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Priyanka Jain [Mon, 27 Aug 2018 09:45:19 +0000 (15:15 +0530)]
phy: Add 25G_AUI, XLAUI, CAUI2, CAUI4 related macros
NXP SoCs like LX2160A can support new ethernet modes
which are 25G_AUI(25G), XLAUI(40G), CAUI2(50G)
and CAUI4(100G)
Add corresponding macros definitions in phy_interface.h
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Janine Hagemann [Tue, 28 Aug 2018 06:25:39 +0000 (08:25 +0200)]
net: phy: ti: Add binding for the CLK_OUT pin muxing
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.
Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Janine Hagemann [Tue, 28 Aug 2018 06:25:38 +0000 (08:25 +0200)]
net: phy: ti: Recover from "port mirroring" N/A MODE4
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
Janine Hagemann [Tue, 28 Aug 2018 06:25:37 +0000 (08:25 +0200)]
net: phy: ti: Add lane swapping support in the DP83867 TI's PHY driver
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.
Bin Meng [Tue, 31 Jul 2018 09:55:23 +0000 (02:55 -0700)]
linux/if_ether.h: Add VLAN related macros
There are VLAN related macros defined in include/linux/if_vlan.h
in Linux kernel, as well as some kernel useful structures and inline
functions. Instead of a complete import from kernel, let's add these
VLAN macros to U-Boot's include/linux/if_ether.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Tue, 31 Jul 2018 09:55:22 +0000 (02:55 -0700)]
net.h: Include linux/if_ether.h to avoid duplication
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Mon, 8 Oct 2018 19:13:03 +0000 (14:13 -0500)]
mtd: uboot: Fix hanging during mtd list command
Some boards (like omap3_logic) hang when trying to access
address 0. This happens when executing the new 'mtd list' command.
This patch enhances the checks for conditions that would
preclude mtd_probe_devices() from operating.
Fixes: 5db66b3aee6f ("cmd: mtd: add 'mtd' command") Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Bin Meng [Thu, 26 Jul 2018 10:15:58 +0000 (03:15 -0700)]
linux/compat.h: Add netdev_### log macros
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Mon, 1 Oct 2018 18:22:47 +0000 (12:22 -0600)]
video: at91: Adjust vidconsole_position_cursor() to use char pos
At present this function uses pixels but it seems more useful for it to
position in terms of characters on the screen. This also matches the
comment to the function. Update this.
Unfortunately there is one user of this function (at91). Have a crack at
fixing this, since I cannot test it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Anatolij Gustschin <agust@denx.de>
Simon Glass [Mon, 1 Oct 2018 18:22:46 +0000 (12:22 -0600)]
sysreset: Add a way to find the last reset
We have a method to return the last reset as a string for humans, but not
a method that allows it to be used programmatically. Add a new method that
returns the last reset as an enum.
Simon Glass [Mon, 1 Oct 2018 18:22:43 +0000 (12:22 -0600)]
fdt: Allow C++ comments in link scripts and DT files
At present // in a device-tree file or link script causes a warning. But
this is used in the standard license header. Update the compiler flags to
use C99, which permits this.
Simon Glass [Mon, 1 Oct 2018 18:22:42 +0000 (12:22 -0600)]
ctags: Minor changes to fix ctags output
At present ctags emits lines with unmatched quotes which means that the
output file is invalid. This is with exuberant-ctags version 5.9~svn201103
but I also see it with plain ctags. I am not sure that it is a bug though.
Make a few minor changes in the source code to fix this problem.
Simon Glass [Mon, 1 Oct 2018 18:22:41 +0000 (12:22 -0600)]
panel: Expand the backlight support
At present the panel can be turned on but not off, and the brightness
cannot be controlled at run-time. Add a new API function to both the panel
and backlight uclasses to handle this. Enhance the PWM backlight driver
to deal with custom levels properly and allow the backlight to be turned
on and off.
Simon Glass [Mon, 1 Oct 2018 18:22:37 +0000 (12:22 -0600)]
x86: Update mtrr functions to allow leaving cache alone
At present the mtrr functions disable the cache before making changes and
enable it again afterwards. This is fine in U-Boot, but does not work if
running in CAR (such as we are in SPL).
Update the functions so that the caller can request that caches be left
alone.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 1 Oct 2018 18:22:36 +0000 (12:22 -0600)]
cros: Update ec_commands to latest version
This file has changed quite a bit in the last 5 years as the capabilities
of the ECs have grown. Sync it up with the copy in coreboot commit b9141f2215.
The only change is the addition of EC_VBNV_BLOCK_SIZE_V2. This is needed
because U-Boot uses the new v2 vboot API and this is not currently fully
supported by Chromium OS firmware.
Simon Glass [Mon, 1 Oct 2018 18:22:35 +0000 (12:22 -0600)]
Rename GPT_HEADER_SIGNATURE to avoid conflict
The current name conflicts with the Chrome OS verified boot library, which
prevents it being built. That library uses a string whereas U-Boot uses a
64-bit hex value. Rename this in U-Boot.
Simon Glass [Mon, 1 Oct 2018 18:22:30 +0000 (12:22 -0600)]
binman: Move to three-digit test-file numbers
We now have 99 tests. Before adding any more, rename everything to three
digits. This helps to preserve the ordering of tests and makes it easier
to find things.
Simon Glass [Mon, 1 Oct 2018 18:22:27 +0000 (12:22 -0600)]
tpm: Use livetree and allow children
Adjust the TPM drivers to use livetree (only one does not). Also,
sometimes TPMs can have child devices if they provide a service to the
system (such as storing secure data), so permit that.
Simon Glass [Mon, 1 Oct 2018 18:22:24 +0000 (12:22 -0600)]
dm: spi: Add logging of some return values
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.
Simon Glass [Mon, 1 Oct 2018 18:22:22 +0000 (12:22 -0600)]
cros: Update cros_ec code to use struct udevice
At present we pass around a private pointer to specify the cros_ec device.
With driver model it makes more sense to pass the device. Update the code
to do this.
Simon Glass [Mon, 1 Oct 2018 18:22:20 +0000 (12:22 -0600)]
serial: Allow serial to be absent in TPL
At present this option applies to SPL, but it should be available in TPL
also, and separately. Change to using CONFIG_IS_ENABLED(), add a new
Kconfig option and fix up hang().
Simon Glass [Mon, 1 Oct 2018 18:22:18 +0000 (12:22 -0600)]
fdt: Allow indicating a node is for U-Boot proper only
At present it is not possible to specify that a node should be used before
relocation (in U-Boot proper) without it also ending up in SPL and TPL
device trees. Add a new "u-boot,dm-pre-proper" boolean property for this.
Simon Glass [Mon, 1 Oct 2018 18:22:13 +0000 (12:22 -0600)]
blk: Support block drivers in TPL
At present it is not possible to enable/disable block drivers in TPL. This
is needed to provide sandbox support. Add a Kconfig option and adjust the
Makefile.
Simon Glass [Mon, 1 Oct 2018 18:22:11 +0000 (12:22 -0600)]
Makefile: Add a warning if SPL/TPL cannot be built
At present the build fails in strange ways if CONFIG_SPL is defined by
CONFIG_SUPPORT_SPL is not. Add a warning for this case as it can be very
confusing to debug.
Simon Glass [Mon, 1 Oct 2018 18:22:09 +0000 (12:22 -0600)]
sf: Avoid allocating memory on every read operation
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.
Remove the allocation and use a variable-sized array instead.
Simon Glass [Mon, 1 Oct 2018 18:22:08 +0000 (12:22 -0600)]
dm: core: Update ofnode to read binman-style flash entry
At present ofnode_read_fmap_entry() reads a flash map entry in a format
which is not supported by binman. To allow use to use binman-format
descriptions, update this function.
Simon Glass [Mon, 1 Oct 2018 17:55:20 +0000 (11:55 -0600)]
sandbox: Restore blocking I/O on exit
At present sandbox sets non-blocking I/O as soon as any input is read
from the terminal. However it does not restore the previous state on
exit. Fix this and drop the old os_read_no_block() function.
This means that we always enable blocking I/O in sandbox (if input is a
terminal) whereas previously it would only happen on the first call to
tstc() or getc(). However, the difference is likely not important.
projects / u-boot.git / log