Please note that, as there is no notion of "current directory" on u-boot,
a directory name specified must contains an absolute directory path as
a parent directory. Otherwise, "/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, all the necessary code for allowing for a file offset
at write is implemented. What plays a major roll here is get_set_cluster(),
which, in contrast to its counterpart, set_cluster(), only operates on
already-allocated clusters, overwriting with data.
So, with a file offset specified, set_contents() seeks and writes data
with set_get_cluster() until the end of a file, and, once it reaches
there, continues writing with set_cluster() for the rest.
Please note that a file will be trimmed as a result of write operation if
write ends before reaching file's end. This is an intended behavior
in order to maintain compatibility with the current interface.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
fs: fat: refactor write interface for a file offset
The current write implementation is quite simple: remove existing clusters
and then allocating new ones and filling them with data. This, inevitably,
enforces always writing from the beginning of a file.
As the first step to lift this restriction, fat_file_write() and
set_contents() are modified to accept an additional parameter, file offset
and further re-factored so that, in the next patch, all the necessary code
will be put into set_contents().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, write implementation is overhauled and rewritten by
making full use of directory iterator. The obvious bonus is that we are
now able to write to a file with a directory path, like /A/B/C/FILE.
Please note that, as there is no notion of "current directory" on u-boot,
a file name specified must contain an absolute directory path. Otherwise,
"/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
It would be good that FAT write function return error code instead of
just returning -1 as fat_read_file() does.
This patch attempts to address this issue although it is 'best effort
(or estimate)' for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
FAT file system's long file name support is a bit complicated and has some
restrictions on its naming. We should be careful about it especially for
write as it may easily end up with wrong file system.
normalize_longname() check for the rules and normalize a file name
if necessary. Please note, however, that this function is yet to be
extended to fully comply with the standard.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
fs: fat: assure iterator's ->dent belongs to ->clust
In my attempt to re-work write operation, it was revealed that iterator's
"clust" does not always point to a cluster to which a current directory
entry ("dent") belongs.
This patch assures that it is always true by adding "next_clust" which is
used solely for dereferencing a cluster chain.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
fs: fat: handle "." and ".." of root dir correctly with fat_itr_resolve()
FAT's root directory does not have "." nor ".."
So care must be taken when scanning root directory with fat_itr_resolve().
Without this patch, any file path starting with "." or ".." will not be
resolved at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
get_fs_info() was introduced in major re-work of read operation by Rob.
We want to reuse this function in write operation by extending it with
additional members in fsdata structure.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Add the missing SPDX-License-Identifier based on Linux kernel commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license").
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Add the missing SPDX-License-Identifier based on Linux kernel commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license").
Correct formatting errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Stephen Warren [Thu, 30 Aug 2018 21:43:44 +0000 (15:43 -0600)]
ARM: tegra: reserve unmapped RAM so EFI doesn't use it
Tegra U-Boot ensures that board_get_usable_ram_top() never returns a value
over 4GB, since some peripherals can't access such addresses. However, on
systems with more than 2GB of RAM, RAM bank 1 does describe this extra
RAM, so that Linux (or whatever OS) can use it, subject to DMA
limitations. Since board_get_usable_ram_top() points at the top of RAM
bank 0, the memory locations describes by RAM bank 1 are not mapped by
U-Boot's MMU configuration, and so cannot be used for anything.
For some completely inexplicable reason, U-Boot's EFI support ignores the
value returned by board_get_usable_ram_top(), and EFI memory allocation
routines will return values above U-Boot's RAM top. This causes U-Boot to
crash when it accesses that RAM, since it isn't mapped by the MMU. One
use-case where this happens is TFTP download of a file on Jetson TX1
(p2371-2180).
This change explicitly tells the EFI code that this extra RAM should not
be used, thus avoiding the crash.
A previous attempt to make EFI honor board_get_usable_ram_top() was
rejected. So, this patch will need to be replicated for any board that
implements board_get_usable_ram_top().
Fixes: aa909462d018 ("efi_loader: efi_allocate_pages is too restrictive") Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Alexander Graf <agraf@suse.de>
The number of bytes in an utf-8 string is an upper limit for the number of
words in the equivalent utf-16 string. In so far the inumbant coding works
correctly. For non-ASCII characters the utf-16 string is shorter. With the
patch only the necessary buffer size is allocated for the load options.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
The length of a string printed to the console by the
EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL is not limited by the UEFI spec.
Hence should not allocate a buffer for it on the stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
utf8_get() - get next UTF-8 code point from buffer
utf8_put() - write UTF-8 code point to buffer
utf8_utf16_strnlen() - length of a utf-8 string after conversion to utf-16
utf8_utf16_strncpy() - copy a utf-8 string to utf-16
utf16_get() - get next UTF-16 code point from buffer
utf16_put() - write UTF-16 code point to buffer
utf16_strnlen() - number of codes points in a utf-16 string
utf16_utf8_strnlen() - length of a utf-16 string after conversion to utf-8
utf16_utf8_strncpy() - copy a utf-16 string to utf-8
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
The function names utf16_strlen() and utf16_strnlen() are misnomers.
The functions do not count utf-16 characters but non-zero words.
So let's rename them to u16_strlen and u16_strnlen().
In utf16_dup() avoid assignment in if clause.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 8 Aug 2018 09:54:32 +0000 (03:54 -0600)]
efi_loader: Pass address to fs_read()
The fs_read() function wants to get an address rather than the
pointer to a buffer.
So let's convert the passed buffer from pointer back a the address
to make efi_loader on sandbox happier.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Simon Glass [Wed, 8 Aug 2018 09:54:30 +0000 (03:54 -0600)]
efi: sandbox: Tidy up copy_fdt() to work with sandbox
At present this function takes a pointer as its argument, then passes this
to efi_allocate_pages(), which actually takes an address. It uses casts,
which are not supported on sandbox.
Also the function calculates the FDT size rounded up to the neared EFI
page size, then its caller recalculates the size and adds a bit more to
it.
This function is much better written as something that works with
addresses only, and returns both the address and the size of the relocated
FDT.
Also, copy_fdt() returns NULL on error, but really should propagate the
error from efi_allocate_pages(). To do this it needs to return an
efi_status_t, not a void *.
Update the code in this way, so that it is easier to follow, and also
supports sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Tom Rini [Thu, 20 Sep 2018 00:35:05 +0000 (20:35 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
fix: cmd: mvebu: Exclude mvebu commands from SPL builds
Exclude mvebu commands from SPL builds
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
fix: mvebu: Add SPI parameters for environment setup
Add definitions for CONFIG_ENV_SPI_BUS and CONFIG_ENV_SPI_CS
to Armada-388-GP board configuration
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
fix: env: Fix the SPI flash device setup for DM mode
For some reason the spi_flash_probe_bus_cs() is called
inside the setup_flash_device() with zero values in place
of configurated SPI flash mode and maximum flash speed.
This code causes HALT error during startup environment
relocation on some platforms - namely Armada-38x-GP board.
Fix the function call by replacing zeros with the appropriate
values - CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
fix: nand: pxa3xx: Add WA for eliminating flash ready timeout
add delay before processing the status flags in pxa3xx_nand_irq().
Signed-off-by: David Sniatkiwicz <davidsn@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
c: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
nand: pxa3xx: Add support for 8KB page 4 and 8 bit ECC NAND
Add support for NAND chips with 8KB page, 4 and 8 bit ECC (ONFI).
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Ofer Heifetz <oferh@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
nand: pxa3xx: cosmetic: add comments to the timing layout structures
Add comments with timing parameter names and some details about
nand layout fileds.
Remove unneeded definition.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
fix: nand: Replace hardcoded page chunk size with calculated one
Replace the hardcoded value of page chink with value that
depends on flash page size and ECC strength.
This fixes nand access errors for 2K page flashes with 8-bit ECC.
Move the initial flash commannd function assignment past the ECC
structures initialization for eliminating usage of hardcoded page
chunk size value.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Add timings and device ID for Toshiba TC58NVG1S3HTA00 flash
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Victor Axelrod [Wed, 29 Aug 2018 08:56:13 +0000 (11:56 +0300)]
mtd: nand: pxa3xx: add support for 2KB 8-bit flash
Add support for 2KB page 8-bit ECC strength flash layout
Signed-off-by: Victor Axelrod <victora@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Boris Brezillon [Wed, 29 Aug 2018 08:56:12 +0000 (11:56 +0300)]
mtd: nand: pxa3xx: Fix READOOB implementation
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.
We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.
Fixes: 43bcfd2bb24a ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support") Cc: stable@vger.kernel.org Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk> Tested-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:09 +0000 (11:56 +0300)]
mtd: nand: pxa3xx_nand: add support for partial chunks
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.
When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.
When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:
| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |
So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.
When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:
| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |
So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.
Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.
To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.
In order to implement reading of the last chunk, this commit:
- Adds a number of new fields to the pxa3xx_nand_info to describe how
many full chunks and how many chunks we have, the size of full
chunks and partial chunks, both in terms of data area and spare
area.
- Fills in the step_chunk_size and step_spare_size variables to
describe how much data and spare should be read/written for the
current read/program step.
- Reworks the state machine to accommodate doing the additional read
or program step when a last partial chunk is used.
This commit is taken from Linux:
'commit c2cdace755b'
("mtd: nand: pxa3xx_nand: add support for partial chunks")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:08 +0000 (11:56 +0300)]
mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
This commit is taken from Linux:
'commit 154f50fbde53'
("mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.
Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.
Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
This commit is taken from Linux:
'commit 66e8e47eae65'
("mtd: pxa3xx_nand: Fix initial controller configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:06 +0000 (11:56 +0300)]
mtd: pxa3xx_nand: Increase the initial chunk size
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transferred data.
However, the initial chunk size is used in a non-split way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).
Thus, the initial chunk size should be 2048 as well.
On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:
[..]
pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
pxa3xx-nand f10d0000.nand: Wait time out!!!
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
nand: Micron MT29F8G08ABABAWP
nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
This commit is taken from Linux:
'commit c7f00c29aa8'
("mtd: pxa3xx_nand: Increase the initial chunk size")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:05 +0000 (11:56 +0300)]
nand: pxa3xx: Increase READ_ID buffer and make the size static
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
This commit is taken from Linux:
'commit b226eca2088'
("nand: pxa3xx: Increase READ_ID buffer and make the size static")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:04 +0000 (11:56 +0300)]
mtd: nand: pxa3xx-nand: fix random command timeouts
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read
after an erase
This patch is taken from Linux:
'commit 21fc0ef9652f'
("mtd: nand: pxa3xx-nand: fix random command timeouts")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:03 +0000 (11:56 +0300)]
mtd: nand: pxa3xx_nand: fix early spurious interrupt
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Ofer Heifetz [Wed, 29 Aug 2018 08:56:01 +0000 (11:56 +0300)]
mtd: nand: pxa3xx_nand: use nand_to_mtd()
Don't store struct mtd_info in struct pxa3xx_nand_host. Instead use the
one that is already part of struct nand_chip. This brings us in line
with current U-boot and Linux conventions.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
This commit is taken from Linux:
'commit c16340973fcb64614' ("nand: pxa3xx: Increase initial buffer size")
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Ofer Heifetz <oferh@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 17 Aug 2018 10:58:51 +0000 (12:58 +0200)]
phy: marvell: Support changing SERDES map in board file
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Fri, 17 Aug 2018 08:47:42 +0000 (20:47 +1200)]
ARM: mach-mvebu: handle fall-back to UART boot
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.
In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.
Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Stefan Roese <sr@denx.de>
Jon Nettleton [Mon, 13 Aug 2018 15:24:38 +0000 (18:24 +0300)]
tools: kwboot: Make kwboot more robust on a38x
This patch accomplishes 2 things to make the kwboot procedure
on the a38x more reliable.
1) We fill the tty with 1K of the magic bootparam. This helps
with the timing of where the microcode picks up in the read of
the line to ensure we actually catch the break to go into recovery
mode
2) Before starting the xmodem transfer we sleep for 2 seconds
and then flush the line. This allows all the magic bootparam
to be flushed from the line and makes the xmodem transfer reliable
and removes the Bad message failures.
Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Usage:
dm tree Dump driver model tree ('*' = activated)
dm uclass Dump list of instances for each uclass
dm devres Dump list of device resources for each device
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Michael Heimpold [Wed, 22 Aug 2018 20:01:24 +0000 (22:01 +0200)]
binman: fix a few typos in documentation
This fixes four small typos in the README file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log