Kever Yang [Wed, 17 Jan 2018 03:05:38 +0000 (11:05 +0800)]
spl: atf: pass NULL for bl32_ep pc
ATF use bl32_ep_info->pc to decide if thre is an available bl32,
let's mark it as NULL first.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Eddie Cai [Wed, 17 Jan 2018 01:51:41 +0000 (09:51 +0800)]
rockchip: rk3036: enable rockusb support on rk3036 based device
Rockchip Rockusb driver already merged. So we enable rockusb
support on rk3036 based device.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 16 Jan 2018 08:08:18 +0000 (16:08 +0800)]
rockchip: dts: rk3128: update pwm-cell for pwm0
The backlight pwm-cell is 3.
This remove the warning in buildman:
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Property 'pwms', cell 3 is not a phandle reference in /backlight
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Missing property '#pwm-cells' in node /sram@10080400 or bad phandle (referred from /backlight:pwms[3])
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Thu, 25 Jan 2018 14:27:10 +0000 (15:27 +0100)]
rockchip: clk: guard set_parent implementations against OF_PLATDATA
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:06:33 +0000 (14:06 +0800)]
clk: rockchip: clk_rk3288: Implement "assign-clock-parent" and "assign-clock-rate"
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The LCDC assigned rate is 0, it will make boot error,
error log:"pll_para_config: the frequency can not be
0 Hz". Remove them, and the lcdc driver will do the
correct clock rate setting.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:51 +0000 (14:05 +0800)]
config: evb-rk3229: Enable rk gmac configs
Add gmac config support for rk3229 evb.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:30 +0000 (14:05 +0800)]
net: gmac_rockchip: Add support for the RK3228 GMAC
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:12 +0000 (14:05 +0800)]
clk: rockchip: Add rk322x gamc clock support
Assuming mac_clk is fed by an external clock, set clk_rmii_src
clock select control register from IO for rgmii interface.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:51 +0000 (14:04 +0800)]
rockchip: pinctrl: Add rk322x gmac pinctrl support
Set gmac pins iomux and rgmii tx pins to 12ma drive-strength,
clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:26 +0000 (14:04 +0800)]
rockchip: pinctrl: rk322x: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:11 +0000 (14:04 +0800)]
rockchip: dts: rk3328-evb: Enable gmac2io for rk3328-evb
Add rk3328-evb gmac support.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:56 +0000 (14:03 +0800)]
rockchip: dts: rk3328: Add gmac2io support
Add basic dts configuration for rk3328 gmac2io.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:23 +0000 (14:03 +0800)]
rockchip: configs: Enable GMAC configs for evb-rk3328
Enable GMAC configs for evb-rk3328
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:04 +0000 (14:03 +0800)]
net: gmac_rockchip: Add rk3328 gmac support
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:36 +0000 (14:02 +0800)]
clk: rockchip: Add rk3328 gamc clock support
The rk3328 soc has two gmac controllers, one is gmac2io,
the other is gmac2phy. We use the gmac2io rgmii interface
for 1000M phy here.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:07 +0000 (14:02 +0800)]
rockchip: pinctrl: Add rk3328 gmac pinctrl support
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:45 +0000 (14:01 +0800)]
rockchip: pinctrl: rk3328: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:12 +0000 (14:01 +0800)]
net: gmac_rockchip: Add support for the RV1108 GMAC
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:57 +0000 (13:53 +0800)]
rockchip: pinctrl: rv1108: Move the iomux definitions into pinctrl-driver
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:56 +0000 (13:53 +0800)]
rockchip: grf_rv1108.h: Fix the grf offsets
The last 4 grf registers offset of rv1108 are wrong, fix them
for correct usage.
Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:55 +0000 (13:53 +0800)]
rockchip: configs: Enable CONFIG_NET_RANDOM_ETHADDR for rk3288-evb
If the Ethernet address is not set, the network can't work,
enable the random address config for default use.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:54 +0000 (13:53 +0800)]
rockchip: dts: rk3399-evb: Change the tx/rx delay value for transmission quality
Give the mac controller the correct tx-delay and rx-delay value
for the rgmii mode transmission. If they are not matched, there
would be Ethernet packets lost, the net feature may not work.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 8 Jan 2018 13:00:27 +0000 (14:00 +0100)]
rockchip: clk: rk3399: accept all assigned-clocks from the 'cru'-node
The RK3399 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3399 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
simply ignore the set_rate() operation and return 0 to signal success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Philipp Tomsich [Mon, 8 Jan 2018 12:59:18 +0000 (13:59 +0100)]
clk: implement clk_set_defaults()
Linux uses the properties 'assigned-clocks', 'assigned-clock-parents'
and 'assigned-clock-rates' to configure the clock subsystem for use
with various peripheral nodes.
This implements clk_set_defaults() and hooks it up with the general
device probibin in drivers/core/device.c: when a new device is probed,
clk_set_defaults() will be called for it and will process the
properties mentioned above.
Note that this functionality is designed to fail gracefully (i.e. if a
clock-driver does not implement set_parent(), we simply accept this
and ignore the error) as not to break existing board-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Series-version: 2
Cover-letter:
clk: support assigned-clock, assigned-clock-parents, assigned-clock-rates
For various peripherals on Rockchip SoCs (e.g. for the Ethernet GMAC),
the parent-clock needs to be set via the DTS. This adds the required
plumbing and implements the GMAC case for the RK3399.
END
This implements the (newly added) set_parent() operation for the
RK3399 with a focus on allowing the RGMII clock parent to be
configured via the assigned-clock-parents property of the GMAC node.
This implementation supports only the GMAC (in fact only the RGMII
clock parent) and allows to set this clock's parent either to the
internal SCLK_GMAC or to an external clock input (identifiable by it
providing a 'clock-output-name' of "gmac_clkin").
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Philipp Tomsich [Mon, 8 Jan 2018 10:18:18 +0000 (11:18 +0100)]
clk: refactor clk_get_by_index() into clk_get_by_indexed_prop()
The logic in clk_get_by_index() may be useful for other properties
than 'clocks': e.g. 'assigned-clocks' and 'assigned-clock-parents'
follows the same model.
This commit refactors clk_get_by_index() by introducing an internal
function clk_get_by_indexed_prop() that allows to specify the name
of the property to process. The original clk_get_by_index() call
is simply directed through this helper function with the property
name fixed to "clocks".
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Marek Vasut [Sun, 7 Jan 2018 18:32:56 +0000 (19:32 +0100)]
ARM: rmobile: Convert R8A7791 Porter board to DM and DT
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Wed, 17 Jan 2018 21:47:21 +0000 (22:47 +0100)]
ARM: dts: rmobile: Add SoC and board U-Boot DT extras
Add U-Boot DT extras for each SoC and board. This marks the required
nodes with u-boot,dm-pre-reloc to start clock and PRR early on while
avoiding modification of the DTs imported from Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Stout board is not supported in Linux, so add a rudimentary DTS
for H2 Stout as a placeholder for when a proper DTS is available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The Stout is already being shipped over, so proper DTS for both
U-Boot and Linux will happen once it's delivered :-)
Marek Vasut [Fri, 19 Jan 2018 17:57:17 +0000 (18:57 +0100)]
net: sh_eth: Add DM and DT support
Add DM capable code into the SH ethernet driver and support probing
both from DT and pdata. The legacy non-DM, non-DT support is retained
as there are still systems in the tree which are not DM or DT capable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 21 Jan 2018 14:10:21 +0000 (15:10 +0100)]
net: sh_eth: Split sh_eth_init
Split sh_eth_init() function into smaller chunks, which can
be called from both DM and non-DM code while handling the
specifics of both configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 21 Jan 2018 13:55:44 +0000 (14:55 +0100)]
net: sh_eth: Separate out MAC address programming
Pull out the code for writing MAC address into the NIC into a
separate function, so it can be reused by both DM and non-DM
code. This is done in preparation for DM support, which handles
MAC address programming separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 21 Jan 2018 14:39:50 +0000 (15:39 +0100)]
net: sh_eth: Split sh_eth_recv
Split sh_eth_recv into two functions, one which checks whether
a packet was received and one which handles the received packet.
This is done in preparation for DM support, which handles these
two parts separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 21 Jan 2018 13:27:51 +0000 (14:27 +0100)]
net: sh_eth: Pass sh_eth_dev around
Pass sh_eth_dev structure around instead of eth_device, since the
later is specific to the legacy networking support. This change is
done in preparation for the DM addition.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Add driver for the Renesas RCar PCIe controller present on Gen2 SoCs.
The PCIe on Gen2 is used both to connect external PCIe peripherals as
well as access the on-SoC USB EHCI controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Maxime Ripard [Tue, 23 Jan 2018 20:17:03 +0000 (21:17 +0100)]
sunxi: Transition from the MMC to a FAT-based environment
The current environment has been hardcoded to an offset that starts to be
an issue given the current size of our main U-Boot binary.
By implementing a custom environment location routine, we can always favor
the FAT-based environment, and fallback to the MMC if we don't find
something in the FAT partition. We also implement the same order when
saving the environment, so that hopefully we can slowly migrate the users
over to FAT-based environment and away from the raw MMC one.
Eventually, and hopefully before we reach that limit again, we will have
most of our users using that setup, and we'll be able to retire the raw
environment, and gain more room for the U-Boot binary.
Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:59 +0000 (21:16 +0100)]
env: Initialise all the environments
Since we want to have multiple environments, we will need to initialise
all the environments since we don't know at init time what drivers might
fail when calling load.
Let's init all of them, and only consider for further operations the ones
that have not reported any errors at init time.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:58 +0000 (21:16 +0100)]
env: Support multiple environments
Now that we have everything in place to support multiple environment, let's
make sure the current code can use it.
The priority used between the various environment is the same one that was
used in the code previously.
At read / init times, the highest priority environment is going to be
detected, and we'll use the same one without lookup during writes. This
should implement the same behaviour than we currently have.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:57 +0000 (21:16 +0100)]
env: common: Make the debug messages play a little nicer
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make the common code play a little nicer by removing all the extra output
in the standard case.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:54 +0000 (21:16 +0100)]
env: Make it explicit where we're loading our environment from
Since we can have multiple environments now, it's better to provide a
decent indication on what environments were tried and which were the one to
fail and succeed.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:53 +0000 (21:16 +0100)]
env: Make the env save message a bit more explicit
Since we'll soon have support for multiple environments, the environment
saving message might end up being printed multiple times if the higher
priority environment cannot be used.
That might confuse the user, so let's make it explicit if the operation
failed or not.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:52 +0000 (21:16 +0100)]
env: Pass additional parameters to the env lookup function
In preparation for the multiple environment support, let's introduce two
new parameters to the environment driver lookup function: the priority and
operation.
The operation parameter is meant to identify, obviously, the operation you
might want to perform on the environment.
The priority is a number passed to identify the environment priority you
want to retrieve. The lowest priority parameter (0) will be the primary
source.
Combining the two parameters allow you to support multiple environments
through different priorities, and to change those priorities between read
and writes operations.
This is especially useful to implement migration mechanisms where you want
to always use the same environment first, be it to read or write, while the
common case is more likely to use the same environment it has read from to
write it to.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 23 Jan 2018 20:16:50 +0000 (21:16 +0100)]
cmd: nvedit: Get rid of the env lookup
The nvedit command is the only user of env_driver_lookup_default outside of
the environment code itself, and it uses it only to print the environment
it's about to save to during env save.
As we're about to rework the environment to be able to handle multiple
environment sources, we might not have an idea of what environment backend
is going to be used before trying (and possibly failing for some).
Therefore, it makes sense to remove that message and move it to the
env_save function itself. As a side effect, we also can get rid of the call
to env_driver_lookup_default that is also about to get refactored.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tom Rini [Fri, 26 Jan 2018 16:24:04 +0000 (11:24 -0500)]
ARM: socfpga: Convert callers of cm_write_with_phase for wait_for_bit_le32
Now that we have and use wait_for_bit_le32() available, the callers of
cm_write_with_phase() should not be casting values to u32 and instead we
expect a const void *, so provide that directly.
Fixes: 48263504c8d5 ("wait_bit: use wait_for_bit_le32 and remove wait_for_bit") Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Chris Blake [Mon, 15 Jan 2018 22:28:18 +0000 (16:28 -0600)]
gpio: sunxi: Add compatible string for H5 PIO
Add allwinner,sun50i-h5-pinctrl compatible for H5 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: remove external link and format commit message] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:24 +0000 (09:44 +0100)]
sunxi: Add limit with the MMC environment
The MMC environment offset is getting very close to the end of the U-Boot
binary now. Since we want to make sure this will not overflow, add a size
limit in the board for arm64. arm32 has already that limit enforced in our
custom image generation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Heider [Tue, 16 Jan 2018 08:44:22 +0000 (09:44 +0100)]
sunxi: imply CONFIG_OF_LIBFDT_OVERLAY
fdt overlay support is useful for all sunxi boards, enable per default
and remove it from sunxi defconfigs.
Signed-off-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:21 +0000 (09:44 +0100)]
net: regex: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this option that is not critical until we can adress the issue
properly.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:20 +0000 (09:44 +0100)]
video: bpp16: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:19 +0000 (09:44 +0100)]
video: bpp8: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:18 +0000 (09:44 +0100)]
cmd: misc: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:17 +0000 (09:44 +0100)]
cmd: loads: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:16 +0000 (09:44 +0100)]
cmd: loadb: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:15 +0000 (09:44 +0100)]
cmd: unzip: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Maxime Ripard [Tue, 16 Jan 2018 08:44:14 +0000 (09:44 +0100)]
cmd: crc32: Disable by default on sunXi
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Eugeniy Paltsev [Thu, 28 Dec 2017 12:09:03 +0000 (15:09 +0300)]
DW SPI: Get clock value from Device Tree
Add option to set spi controller clock frequency via device tree
using standard clock bindings.
Define dw_spi_get_clk function as 'weak' as some targets
(like SOCFPGA_GEN5 and SOCFPGA_ARRIA10) don't use standard clock API
and implement dw_spi_get_clk their own way in their clock manager.
Get rid of clock_manager.h include as we don't use
cm_get_spi_controller_clk_hz function anymore. (we use redefined
dw_spi_get_clk in SOCFPGA clock managers instead)
Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
usb: ehci: mxs: fix swapped argument in ehci_writel()
ehci_writel() swaps the arguments for address and value. One call
in ehci-mxs ignores that.
This fixes the warning:
drivers/usb/host/ehci-mxs.c: In function ?ehci_hcd_stop?:
drivers/usb/host/ehci-mxs.c:159:19: error: initialization makes integer from pointer without a cast [-Werror=int-conversion]
ehci_writel(tmp, &hcor->or_usbcmd);
^
arch/arm/include/asm/io.h:117:34: note: in definition of macro ?writel?
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/usb/host/ehci-mxs.c:159:2: note: in expansion of macro ?ehci_writel?
^~~~~~~~~~~
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Paul Burton [Thu, 18 Jan 2018 22:36:41 +0000 (14:36 -0800)]
boston: Pad binary in .mcs to a multiple of 16 bytes
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the
final 0x00 byte which ends the .relocs section seems to be skipped &
left in flash as 0xff unless the data contained in the .mcs is padded
out to a 16 byte boundary. Without our final zero byte relocation will
fail with an error about a spurious reloc:
Avoid this problem by padding out the data in the .mcs file to a 16 byte
boundary using srec_cat's -range-pad functionality.
Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
arm: socfpga: allow configs without network support
Currently, socfpga_common.h does not allow configurations without
network support. This is because CONFIG_CMD_PXE is defined in this
file and distro mode has DHCP hard-coded as available.
Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs
and by making DHCP optional in BOOT_TARGET_DEVICES(func).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
projects / u-boot.git / log