In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Tom Rini [Mon, 1 May 2023 01:29:50 +0000 (21:29 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
Tom Rini [Sat, 29 Apr 2023 13:29:41 +0000 (09:29 -0400)]
Merge branch 'for-2023.07' of https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
Johan Jonker [Sun, 23 Apr 2023 09:19:41 +0000 (11:19 +0200)]
core: fdtaddr: use map_sysmem() as cast for the return
For the devfdt_get_addr_index_ptr() and devfdt_get_addr_size_index_ptr()
function use map_sysmem() function as cast for the return for use in
sandbox. Also fix sandbox test.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Drop second hunk: Signed-off-by: Simon Glass <sjg@chromium.org>
Variable orig_dir cannot be used in the finally block if it has not be
assigned outside of the try block.
tools/patman/func_test.py:523:21:
E0601: Using variable 'orig_dir' before assignment
(used-before-assignment)
tools/patman/func_test.py:691:21:
E0601: Using variable 'orig_dir' before assignment
(used-before-assignment)
Fixes: fd70986a62af ("patman: Add a test that uses gitpython") Fixes: be051c0c7741 ("patman: Detect missing upstream in CountCommitsToBranch") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
There's quite a few instances of board-specific code doing
off = fdt_path_offset(gd->fdt_blob, ...);
...
ret = uclass_get_device_by_of_offset(..., off, &dev);
looking for an eeprom or a pmic via some alias. Such code can be
simplified a little if we have a helper for directly getting a device
via device tree path (including being given as an alias).
Implement it in terms of ofnode rather than raw offsets so that this
will work whether live tree is enabled or not.
The functions uclass_find_device_by_phandle() and
uclass_get_device_by_phandle_id() both loop over a given uclass
looking for a device with a given phandle. Factor that out to a common
helper.
For now, there are no (known potential) users of the new helper
outside uclass.c, so make it static.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
Fix warning on sandbox_spl; fix code style: Signed-off-by: Simon Glass <sjg@chromium.org>
Pavel Skripkin [Wed, 12 Apr 2023 18:55:44 +0000 (21:55 +0300)]
sandbox: disable tracing before unmapping RAM
Currently doing 'reset' command in sandbox with tracing enabled causes
SIGSEV
```
Hit any key to stop autoboot: 0
=>
=>
=> reset
resetting ...
Segmentation fault (core dumped)
```
Tracing callback uses RAM buffer for storing tracing reports, but
state_uninit() function unmaps whole RAM, which causes SIGSEV on umapped
memory inside tracing subsystem.
Fix it by disabling tracing before unmapping memory
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing check for CONFIG_TRACE: Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 6 Apr 2023 14:03:33 +0000 (10:03 -0400)]
bootflow: Rework do_bootflow_menu() slightly
When building this with clang, we get a warning such as:
cmd/bootflow.c:412:27: warning: variable 'bflow' is uninitialized when used here [-Wuninitialized]
printf("Selected: %s\n", bflow->os_name ? bflow->os_name : bflow->name);
^~~~~
And a suggestion to just initialize bflow to NULL. This would however
would be ensuring a bad dereference. Instead, looking at the function we
rework things so that when CONFIG_EXPO is not enabled (and so, no UI) we
error early and would never reach this point in the code. Simplify the
rest slightly as well while at this.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Andrew Davis [Tue, 4 Apr 2023 18:45:41 +0000 (13:45 -0500)]
binman: Use unsigned long over typedef ulong
The header binman_sym.h depends on ulong typedef but does not include
types.h. This means the header must be included after including types.h
or a header that includes it.
We could include types.h but instead let's just switch from ulong
to directly using unsigned long. This removes the need for typedef'ing
it in some of the tests, so also remove those.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
vbe_simple_read_bootflow() calls vbe_simple_read_bootflow_fw()
which is only available when BOOTMETH_VBE_SIMPLE_FW is on.
Signed-off-by: Bin Meng <bmeng@tinylab.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
On cmpc885 board, the ethernet addresses are stored in an
EEPROM that is accessed through SPI.
A 3 bytes command is sent to the chip then the content
gets read. At the time being a single block access is
performed, ignoring the first 3 bytes read.
Reword the SPI transfer to first send 3 bytes then
receive the content of the EEPROM so that there don't be
3 dummy bytes at the beginning of the buffer.
And move the function into common.c so that it can be
reused by the board that will be added in a future patch.
board: cssi: Create dedicated file for common sources
In preparation of the new cssi board called cmpcpro which
we be introduce in a future patch, move common
functions into a dedicated file in a common directory.
Samuel Holland [Sun, 22 Jan 2023 17:23:51 +0000 (11:23 -0600)]
Kconfig: Remove an impossible condition
ARCH_SUNXI selects BINMAN, so the condition "!BINMAN && ARCH_SUNXI"
is impossible to satisfy.
Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 15 Jul 2022 03:34:53 +0000 (22:34 -0500)]
phy: sun4i-usb: Do not drive VBUS with external VBUS present
It is possible to use host-side USB with externally-provided VBUS. For
example, some USB OTG cables have an extra power input which powers
both the board and the USB peripheral.
To support this setup, skip enabling the VBUS switch/regulator if VBUS
voltage is already present. This behavior matches the Linux PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 23:46:21 +0000 (17:46 -0600)]
sunxi: Switch to PMIC USB power supply VBUS detection
Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.
The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.
Additionally, the following board intentionally omits the property
because VBUS is always enabled:
- Nintendo_NES_Classic_Edition_defconfig /
sun8i-r16-nintendo-nes-classic
The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 23:46:20 +0000 (17:46 -0600)]
power: regulator: Add a driver for the AXP USB power supply
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:36 +0000 (16:06 -0600)]
mtd: nand: sunxi: Pass the device to the init function
This more closely matches the U-Boot driver to the Linux version.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Michael Trimarchi <micahel@amarulasolutions.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:35 +0000 (16:06 -0600)]
mtd: nand: sunxi: Convert to the driver model
Clocks, resets, and pinmuxes are now handled by the driver model, so the
only thing the "board" code needs to do is load the driver. This matches
the pattern used by other DM raw NAND drivers (there is no NAND uclass).
The actual board code is now only needed in SPL.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:34 +0000 (16:06 -0600)]
mtd: nand: sunxi: Convert from fdtdec to ofnode
As a first step toward converting this driver to the driver model, use
the ofnode abstraction to replace direct references to the FDT blob.
Using ofnode_read_u32_index removes an extra pair of loops and makes the
allwinner,rb property optional, matching the devicetree binding.
Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:33 +0000 (16:06 -0600)]
mtd: nand: sunxi: Remove an unnecessary check
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:32 +0000 (16:06 -0600)]
pinctrl: sunxi: Add NAND pinmuxes
NAND is always at function 2 on port C.
Pin lists and mux values were taken from the Linux drivers.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sun, 22 Jan 2023 22:06:31 +0000 (16:06 -0600)]
clk: sunxi: Add NAND clocks and resets
Currently NAND clock setup is done in board code, both in SPL and in
U-Boot proper. Add the NAND clocks/resets here so they can be used by
the "full" NAND driver once it is converted to the driver model.
The bit locations are copied from the Linux CCU drivers.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 21 Jan 2023 23:25:17 +0000 (17:25 -0600)]
sunxi: binman: Fix U-Boot offset when SPL is not 32 KiB
On sunxi boards, SPL looks for U-Boot at a 32 KiB offset, unless SPL is
larger than 32 KiB, in which case U-Boot immediately follows SPL. See
the logic in spl_mmc_get_uboot_raw_sector() and spl_spi_load_image().
In two cases, the existing binman description mismatches the SPL code.
For 64-bit boards, binman would place U-Boot immediately following SPL,
even if SPL is smaller than 32 KiB. This can happen when SPL MMC support
is disabled (i.e. when booting from SPI flash).
In contrast, for 32-bit boards, binman would place U-Boot at 32 KiB,
even if SPL is larger than that. This happens because the 'offset'
property does not consider the size of previous entries.
Fix both issues by setting a minimum size for the SPL entry, which
exactly matches the logic in the SPL code. Unfortunately, this size must
be provided as a magic number, since none of the relevant config symbols
(SPL_PAD_TO, SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR, and SYS_SPI_U_BOOT_OFFS)
are guaranteed to be defined in all cases.
Fixes: cfa3db602caf ("sunxi: Convert 64-bit boards to use binman") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To quote the author:
Adding block storage emulation for NVM XIP flash devices.
Some paltforms such as Corstone-1000 need to see NVM XIP raw flash
as a block storage device with read only capability.
Here NVM flash devices are devices with addressable
memory (e.g: QSPI NOR flash).
The NVM XIP block storage emulation provides the following features:
- Emulate NVM XIP raw flash as a block storage device with read only capability
- Being generic by design and can be used by any platform
- Device tree node
- Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them
- A generic NVMXIP block driver allowing to read from the XIP flash
- A generic NVMXIP Uclass driver for binding the block device
- A generic NVMXIP QSPI driver
- Implemented on top of memory-mapped IO (using readq macro)
- Enabling NVMXIP in sandbox64
- A sandbox test case
- Enabling NVMXIP in Corstone1000 platform as a use case
For more details please refer to doc/develop/driver-model/nvmxip.rst
The device associated with this driver is the parent of the blk#<id> device
nvmxip_qspi can be reused by other platforms. If the platform
has custom settings to apply before using the flash, then the platform
can provide its own parent driver belonging to UCLASS_NVMXIP and reuse
nvmxip-blk driver. The custom driver can be implemented like nvmxip_qspi in
addition to the platform custom settings.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
For more details please refer to doc/develop/driver-model/nvmxip_qspi.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Tom Rini [Thu, 27 Apr 2023 20:33:58 +0000 (16:33 -0400)]
Merge branch '2023-04-27-IDE-code-cleanups'
To quote the author:
This code was converted to driver model a long time again but it was a
pretty rough conversion. It introduced a few minor bugs, e.g. the device
capacity is incorrect and some flags are lost (such as lba48).
This series tidies up the code and fixes these bugs. This involves quite
a bit of refactoring, so it is done one patch at a time for easier
review.
Simon Glass [Tue, 25 Apr 2023 16:54:54 +0000 (10:54 -0600)]
ide: Simplify expressions and hex values
The code has quite a few unnecessary brackets and comparisons to zero,
etc. Fix these up as well as some upper-case hex values and use of 0x in
printf() strings.
Simon Glass [Tue, 25 Apr 2023 16:54:51 +0000 (10:54 -0600)]
ide: Correct LBA setting
Fix a longstanding bug where the LBA is calculated as the size of the
media instead of the number of blocks. This was perhaps not noticed
earlier since it prints the correct value first, before setting the wrong
value.
Drop the unnecessary blksz variable while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 68e6f221ed0 ("block: ide: Fix block read/write with driver model")
Simon Glass [Tue, 25 Apr 2023 16:54:48 +0000 (10:54 -0600)]
ide: Make ide_ident() return an error code
Update ide_ident() to indicate whether it finds a device or not. Use
that to decide whether to create a block device for it, rather than
looking DEV_TYPE_UNKNOWN.
Simon Glass [Tue, 25 Apr 2023 16:54:44 +0000 (10:54 -0600)]
ide: Move setting of vendor strings into ide_probe()
The current implementation adds this information in the block device's
probe() function, which is called in the blk_probe_or_unbind() in
ide_probe().
It is simpler to do this in ide_probe() itself, since the effect is the
same. This helps to consolidate use of ide_dev_desc[] which we would like
to remove.
Simon Glass [Tue, 25 Apr 2023 16:54:41 +0000 (10:54 -0600)]
ide: Avoid preprocessor for CONFIG_LBA48
Use IS_ENABLED() instead for all conditions. Add the 'lba48' flag into
struct blk_desc always, since it uses very little space. Use a bool so
the meaning is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Simon Glass [Tue, 25 Apr 2023 16:54:39 +0000 (10:54 -0600)]
ide: Simplify success condition
Change the if() to remove extra brackets and check for the positive case
first, i.e. when a device is found. Exit the loop in that case, with the
retry logic in the 'else' part.
Simon Glass [Tue, 25 Apr 2023 16:54:38 +0000 (10:54 -0600)]
ide: Refactor confusing loop code
This code is hard to follow as it uses #ifdef in a strange way. Adjust
it to avoid the preprocessor. Drop the special return for the non-ATAPI
case since we can rely on tries becoming 0 and exiting the loop.
Simon Glass [Tue, 25 Apr 2023 16:54:37 +0000 (10:54 -0600)]
ide: Change the retries variable
Use a 'tries' variable which starts at the number of tries we want to do,
rather than a 'retries' one that stops at either 1 or 2. This will make it
easier to refactor the code to avoid the horrible #ifdefs
Simon Glass [Tue, 25 Apr 2023 16:54:35 +0000 (10:54 -0600)]
ide: Correct use of ATAPI
The use of atapi_read() was incorrect dropped. Fix this so that it will
be used when needed. Use a udevice for the first argument of atapi_read()
so it is consistent with ide_read().
This requires much of the ATAPI code to be brought out from behind the
existing #ifdef. It will still be removed by the compiler if it is not
needed.
Add an atapi flag to struct blk_desc so the information can be retained.
Fixes: 145df842b44 ("dm: ide: Add support for driver-model block devices") Fixes: d0075059e4d ("ide: Drop non-DM code for BLK") Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 25 Apr 2023 16:54:30 +0000 (10:54 -0600)]
ide: Move ide_init() into probing
At present the code does ide_init() as a separate operation, then calls
device_probe() to copy over the information. We can call ide_init() from
probe just as easily.
The only difference is that using 'ide init' twice will do nothing.
However it already fails to copy over the new data in that case, so the
effect is the same. For now, unbind the block devices and remove the IDE
device, which causes the bus to be probed again. Later patches will fix
this up fully, so that all blk_desc data is copied across.
Since ide_reset() is only called from ide_init(), there is no need to init
the ide_dev_desc[] array. This is already done at the end of ide_init() so
drop this code.
The call to uclass_first_device() is now within the probe() function of
the same device, so does nothing. Drop it.
Simon Glass [Mon, 24 Apr 2023 01:49:52 +0000 (13:49 +1200)]
rockchip: Use the same boot_targets for all boards
It doesn't really matter if we mention things which are not present. For
example, if 'nvme' is included but the board does not support it, it just
continues with the next item in the list.
It is simpler to use the same target list for all boards, so drop the
different one for rk3399.
bootstd: Use blk uclass device numbers to set efi bootdev
When loading a file from a block device, efiload_read_file
was using the seq_num of the device (e.g "35" of virtio_blk#35)
instead of the block device id (e.g what you get from running
the corresponding device scan command, like "virtio 0")
This cause EFI booting from these devices to fail as an
invalid device number is passed to blk_get_device_part_str:
Scanning bootdev 'virtio-blk#35.bootdev':
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
setting bootdev virtio, 35, efi/boot/bootaa64.efi, 00000000beef9a40, 170800
efi_dp_from_name calling blk_get_device_part_str
dev=virtio devnr=35 path=efi/boot/bootaa64.efi
blk_get_device_part_str (virtio,35)
blk_get_device_by_str (virtio, 35)
** Bad device specification virtio 35 **
Using default device tree: dtb/qemu-arm.dtb
No device tree available
0 efi ready virtio 1 virtio-blk#35.bootdev.par efi/boot/bootaa64.efi
** Booting bootflow 'virtio-blk#35.bootdev.part_1' with efi
blk_get_device_part_str (virtio,0:1)
blk_get_device_by_str (virtio, 0)
No UEFI binary known at beef9a40 (image buf=00000000beef9a40,addr=0000000000000000)
Boot failed (err=-22)
Signed-off-by: Mathew McBride <matt@traverse.com.au> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 24 Apr 2023 01:49:49 +0000 (13:49 +1200)]
bootstd: Adjust code ordering to work around compiler quirk
At present when debugging is off, bootdev_find_in_blk() sometimes fails
to find a valid bootflow, e.g. with virtio. Accessing the 'blk' variable
later in the function seems to correct it.
Move the 'ret' check before the debug statement and set the block device
again aftewards, to work around this.
Simon Glass [Mon, 24 Apr 2023 01:49:47 +0000 (13:49 +1200)]
bootstd: Report missing labels only when asked
Use the -l flag to indicate whether to report missing uclasses.
Also try to be more helpful when no devices are found. For example, when
we see something 'scsi0' requested and nothing was found, this indicates
that there are no SCSI devices, so show a suitable message.
Move messages out of the low-level functions so that silent operation
is possible.
This means they are never reported unless BOOTSTD_FULL is enabled, since
the -l flag cannot otherwise be set.
Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 24 Apr 2023 01:49:46 +0000 (13:49 +1200)]
bootstd: Support booting EFI where multiple options exist
The current EFI implementation has a strange quirk where it watches
loaded files and uses the last-loaded file to determine the device that
is being booted from.
This is confusing with bootstd, where multiple options may exist. Even
loading a device tree will cause it to go wrong. There is no API for
passing this information, since the only entry into booting an EFI image
is the 'bootefi' command.
To work around this, call efi_set_bootdev() for EFI images, if possible,
just before booting.
- A few TI, mpc8379erdb and vexpress64 updates, some arm64 core updates,
test cleanups, Xen cleanups, assorted code and Kconfig cleanups (many
in preparation for using clang on ARM), psci pre-reloc fixes, enable
PCI bus mastering for ATA devices, and a gpio-uclass bugfix
gpio-uclass: fix off-by-one in gpio_request_list_by_name_nodev()
By the time we jump to the err label, count represents the number of
gpios we've successfully requested. So by subtracting one, we fail to
free the most recently requested.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log