From: Oliver Graute Date: Mon, 31 May 2021 13:50:40 +0000 (+0200) Subject: imx: support for conga-QMX8 board X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=fe133eb192a8a55813a4dc5ec72ecf45ba74f65e;p=u-boot.git imx: support for conga-QMX8 board Add i.MX8QM qmx8 congatec board support U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute Cc: Stefano Babic Cc: Fabio Estevam Cc: Peng Fan Cc: Simon Glass Cc: Ye Li Cc: uboot-imx --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index d29844e765..8889d5b1ca 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -842,6 +842,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ dtb-$(CONFIG_ARCH_IMX8) += \ fsl-imx8qm-apalis.dtb \ fsl-imx8qm-mek.dtb \ + imx8qm-cgtqmx8.dtb \ imx8qm-rom7720-a1.dtb \ fsl-imx8qxp-ai_ml.dtb \ fsl-imx8qxp-colibri.dtb \ diff --git a/arch/arm/dts/imx8qm-cgtqmx8.dts b/arch/arm/dts/imx8qm-cgtqmx8.dts new file mode 100644 index 0000000000..555c357f6f --- /dev/null +++ b/arch/arm/dts/imx8qm-cgtqmx8.dts @@ -0,0 +1,404 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Copyright 2017 NXP + * Copyright 2017 congatec AG + * Copyright (C) 2019 Oliver Graute + */ + +/dts-v1/; + +/* First 128KB is for PSCI ATF. */ +/memreserve/ 0x80000000 0x00020000; + +#include "fsl-imx8qm.dtsi" + +/ { + model = "Congatec QMX8 Qseven series"; + compatible = "fsl,imx8qm-qmx8", "fsl,imx8qm"; + + chosen { + bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200"; + stdout-path = &lpuart0; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usdhc2_vmmc: usdhc2_vmmc { + compatible = "regulator-fixed"; + regulator-name = "sw-3p3-sd1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3000>; + }; + + reg_usdhc3_vmmc: usdhc3_vmmc { + compatible = "regulator-fixed"; + regulator-name = "sw-3p3-sd2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii"; + phy-handle = <ðphy0>; + fsl,magic-packet; + fsl,rgmii_txc_dly; + fsl,rgmii_rxc_dly; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + at803x,eee-disabled; + at803x,vddio-1p8v; + }; + }; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio5 { + status = "okay"; +}; + +&i2c0 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c0>; + clock-frequency = <100000>; + status = "okay"; + + rtc_ext: m41t62@68 { + compatible = "st,m41t62"; + reg = <0x68>; + }; +}; + +&i2c1 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c1>; + status = "okay"; + + wm8904: wm8904@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + + clocks = <&clk IMX8QM_AUD_MCLKOUT0>; + clock-names = "mclk"; + wlf,shared-lrclk; + /* power-domains = <&pd_mclk_out0>; */ + + assigned-clocks = <&clk IMX8QM_AUD_PLL0_DIV>, + <&clk IMX8QM_AUD_ACM_AUD_PLL_CLK0_DIV>, + <&clk IMX8QM_AUD_ACM_AUD_REC_CLK0_DIV>, + <&clk IMX8QM_AUD_MCLKOUT0>; + + assigned-clock-rates = <786432000>, <49152000>, <24576000>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx8qm-qmx8 { + + pinctrl_hog: hoggrp{ + fsl,pins = < + SC_P_M40_GPIO0_01_LSIO_GPIO0_IO09 0x00000021 + SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04 0x00000021 + SC_P_M40_GPIO0_00_LSIO_GPIO0_IO08 0x00000021 + SC_P_ESAI1_SCKT_LSIO_GPIO2_IO07 0x00000021 + SC_P_SPDIF0_TX_LSIO_GPIO2_IO15 0x00000021 + SC_P_FLEXCAN1_RX_LSIO_GPIO3_IO31 0x00000021 + SC_P_ESAI1_TX0_LSIO_GPIO2_IO08 0x00000021 + SC_P_FLEXCAN1_TX_LSIO_GPIO4_IO00 0x00000021 + SC_P_ESAI1_TX1_LSIO_GPIO2_IO09 0x00000021 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + SC_P_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + SC_P_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 + SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 + SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 + SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 + SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 + SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 + SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 + SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 + SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 + SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 + SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 + SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 + >; + }; + + pinctrl_lpi2c0: lpi2c0grp { + fsl,pins = < + SC_P_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0xc600004c + SC_P_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0xc600004c + >; + }; + + pinctrl_lpi2c1: lpi2c1grp { + fsl,pins = < + SC_P_GPT0_CLK_DMA_I2C1_SCL 0xc600004c + SC_P_GPT0_CAPTURE_DMA_I2C1_SDA 0xc600004c + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + SC_P_UART0_RX_DMA_UART0_RX 0x06000020 + SC_P_UART0_TX_DMA_UART0_TX 0x06000020 + >; + }; + + pinctrl_lpuart1: lpuart1grp { + fsl,pins = < + SC_P_UART1_RX_DMA_UART1_RX 0x06000020 + SC_P_UART1_TX_DMA_UART1_TX 0x06000020 + SC_P_UART1_CTS_B_DMA_UART1_CTS_B 0x06000020 + SC_P_UART1_RTS_B_DMA_UART1_RTS_B 0x06000020 + >; + }; + + pinctrl_lpuart3: lpuart3grp { + fsl,pins = < + SC_P_M41_GPIO0_00_DMA_UART3_RX 0x06000020 + SC_P_M41_GPIO0_01_DMA_UART3_TX 0x06000020 + >; + }; + + pinctrl_mlb: mlbgrp { + fsl,pins = < + SC_P_MLB_SIG_CONN_MLB_SIG 0x21 + SC_P_MLB_CLK_CONN_MLB_CLK 0x21 + SC_P_MLB_DATA_CONN_MLB_DATA 0x21 + >; + }; + + pinctrl_isl29023: isl29023grp { + fsl,pins = < + SC_P_ADC_IN2_LSIO_GPIO3_IO20 0x00000021 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000040 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000040 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21 0x00000021 + SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021 + SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07 0x00000021 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc3_gpio: usdhc3grpgpio { + fsl,pins = < + SC_P_USDHC2_RESET_B_LSIO_GPIO4_IO09 0x00000021 + SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020 + >; + }; + }; +}; + +&lpuart0 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + status = "okay"; +}; + +&lpuart1 { /* Q7 connector */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart1>; + status = "okay"; +}; + +&pd_dma_lpuart0 { + debug_console; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; + vmmc-supply = <®_usdhc2_vmmc>; + fsl,tuning-start-tap = <20>; + fsl,tuning-step= <2>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>; + bus-width = <4>; + cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc3_vmmc>; + fsl,tuning-start-tap = <20>; + fsl,tuning-step= <2>; + status = "okay"; +}; diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig index 4e76612d05..71221d8d06 100644 --- a/arch/arm/mach-imx/imx8/Kconfig +++ b/arch/arm/mach-imx/imx8/Kconfig @@ -86,6 +86,12 @@ config TARGET_IMX8QM_MEK select BOARD_LATE_INIT select IMX8QM +config TARGET_CONGA_QMX8 + bool "Support congatec conga-QMX8 board" + select BOARD_LATE_INIT + select SUPPORT_SPL + select IMX8QM + config TARGET_IMX8QM_ROM7720_A1 bool "Support i.MX8QM ROM-7720-A1" select BOARD_LATE_INIT @@ -101,6 +107,7 @@ endchoice source "board/freescale/imx8qm_mek/Kconfig" source "board/freescale/imx8qxp_mek/Kconfig" +source "board/congatec/cgtqmx8/Kconfig" source "board/advantech/imx8qm_rom7720_a1/Kconfig" source "board/toradex/apalis-imx8/Kconfig" source "board/toradex/colibri-imx8x/Kconfig" diff --git a/board/congatec/cgtqmx8/Kconfig b/board/congatec/cgtqmx8/Kconfig new file mode 100644 index 0000000000..7273039261 --- /dev/null +++ b/board/congatec/cgtqmx8/Kconfig @@ -0,0 +1,14 @@ +if TARGET_CONGA_QMX8 + +config SYS_BOARD + default "cgtqmx8" + +config SYS_VENDOR + default "congatec" + +config SYS_CONFIG_NAME + default "cgtqmx8" + +source "board/congatec/common/Kconfig" + +endif diff --git a/board/congatec/cgtqmx8/MAINTAINERS b/board/congatec/cgtqmx8/MAINTAINERS new file mode 100644 index 0000000000..53bc0f93b7 --- /dev/null +++ b/board/congatec/cgtqmx8/MAINTAINERS @@ -0,0 +1,7 @@ +i.MX8QM CGTQMX8 BOARD +M: Oliver Graute +S: Maintained +F: board/congatec/cgtqmx8/ +F: arch/arm/dts/imx8qm-cgtqmx8.dts +F: include/configs/cgtqmx8.h +F: configs/cgtqmx8_defconfig diff --git a/board/congatec/cgtqmx8/Makefile b/board/congatec/cgtqmx8/Makefile new file mode 100644 index 0000000000..4b59dbb6bc --- /dev/null +++ b/board/congatec/cgtqmx8/Makefile @@ -0,0 +1,11 @@ +# +# Copyright 2017 NXP +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += cgtqmx8.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif diff --git a/board/congatec/cgtqmx8/cgtqmx8.c b/board/congatec/cgtqmx8/cgtqmx8.c new file mode 100644 index 0000000000..fb0cf09138 --- /dev/null +++ b/board/congatec/cgtqmx8/cgtqmx8.c @@ -0,0 +1,460 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 congatec AG + * Copyright (C) 2019 Oliver Graute + */ +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define ESDHC_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ESDHC_CLK_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ENET_INPUT_PAD_CTRL ((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ENET_NORMAL_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define FSPI_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define I2C_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +static iomux_cfg_t uart0_pads[] = { + SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL), + SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +void board_late_mmc_env_init(void); +void init_clk_usdhc(u32 index); +int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg); + +static void setup_iomux_uart(void) +{ + imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads)); +} + +int board_early_init_f(void) +{ + /* sc_ipc_t ipcHndl = 0; */ + sc_err_t scierr = 0; + + /* When start u-boot in XEN VM, directly return */ + /* if (IS_ENABLED(CONFIG_XEN)) */ + /* return 0; */ + + /* ipcHndl = gd->arch.ipc_channel_handle; */ + + /* Power up UART0, this is very early while power domain is not working */ + scierr = sc_pm_set_resource_power_mode(-1, SC_R_UART_0, SC_PM_PW_MODE_ON); + if (scierr != SC_ERR_NONE) + return 0; + + /* Set UART0 clock root to 80 MHz */ + sc_pm_clock_rate_t rate = 80000000; + + scierr = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate); + if (scierr != SC_ERR_NONE) + return 0; + + /* Enable UART0 clock root */ + scierr = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false); + if (scierr != SC_ERR_NONE) + return 0; + + setup_iomux_uart(); + + return 0; +} + +#if IS_ENABLED(CONFIG_FSL_ESDHC_IMX) + +#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 22) +#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 12) + +static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { + {USDHC1_BASE_ADDR, 0, 8}, + {USDHC2_BASE_ADDR, 0, 4}, + {USDHC3_BASE_ADDR, 0, 4}, +}; + +static iomux_cfg_t emmc0[] = { + SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +static iomux_cfg_t usdhc1_sd[] = { + SC_P_USDHC1_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_USDHC1_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA6 | MUX_MODE_ALT(2) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA7 | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +static iomux_cfg_t usdhc2_sd[] = { + SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_WP | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +int board_mmc_init(struct bd_info *bis) +{ + int i, ret; + struct power_domain pd; + + /* + * According to the board_mmc_init() the following map is done: + * (U-Boot device node) (Physical Port) + * mmc0 (onboard eMMC) USDHC1 + * mmc1 (external SD card) USDHC2 + * mmc2 (onboard µSD) USDHC3 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + /* onboard eMMC */ + if (!imx8_power_domain_lookup_name("conn_sdhc0", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0)); + init_clk_usdhc(0); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; + case 1: + /* external SD card */ + if (!imx8_power_domain_lookup_name("conn_sdhc1", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(usdhc1_sd, ARRAY_SIZE(usdhc1_sd)); + init_clk_usdhc(1); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + gpio_request(USDHC1_CD_GPIO, "sd1_cd"); + gpio_direction_input(USDHC1_CD_GPIO); + break; + case 2: + /* onboard µSD */ + if (!imx8_power_domain_lookup_name("conn_sdhc2", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd)); + init_clk_usdhc(2); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + gpio_request(USDHC2_CD_GPIO, "sd2_cd"); + gpio_direction_input(USDHC2_CD_GPIO); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) than supported by the board\n", i + 1); + return 0; + } + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + + return 0; +} + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC1_BASE_ADDR: + ret = 1; + break; + case USDHC2_BASE_ADDR: + ret = !gpio_get_value(USDHC1_CD_GPIO); + break; + case USDHC3_BASE_ADDR: + ret = !gpio_get_value(USDHC2_CD_GPIO); + break; + } + + return ret; +} + +#endif /* CONFIG_FSL_ESDHC_IMX */ + +#if (IS_ENABLED(CONFIG_FEC_MXC)) + +#include + +static iomux_cfg_t pad_enet0[] = { + SC_P_ENET0_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD0 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD1 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD2 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD3 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXC | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD0 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD1 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD2 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD3 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_MDC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_MDIO | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), +}; + +static void setup_iomux_fec(void) +{ + imx8_iomux_setup_multiple_pads(pad_enet0, ARRAY_SIZE(pad_enet0)); +} + +static void enet_device_phy_reset(void) +{ + gpio_set_value(FEC0_RESET, 0); + udelay(50); + gpio_set_value(FEC0_RESET, 1); + + /* The board has a long delay for this reset to become stable */ + mdelay(200); +} + +int board_eth_init(struct bd_info *bis) +{ + setup_iomux_fec(); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); + + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +static int setup_fec(void) +{ + /* Reset ENET PHY */ + enet_device_phy_reset(); + + return 0; +} +#endif + +#ifdef CONFIG_MXC_GPIO + +#define LVDS_ENABLE IMX_GPIO_NR(1, 6) +#define BKL_ENABLE IMX_GPIO_NR(1, 7) + +static iomux_cfg_t board_gpios[] = { + SC_P_LVDS0_I2C0_SCL | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), + SC_P_LVDS0_I2C0_SDA | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), + SC_P_ESAI1_FST | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), +}; + +static void board_gpio_init(void) +{ + imx8_iomux_setup_multiple_pads(board_gpios, ARRAY_SIZE(board_gpios)); + + /* enable LVDS */ + gpio_request(LVDS_ENABLE, "lvds_enable"); + gpio_direction_output(LVDS_ENABLE, 1); + + /* enable backlight */ + gpio_request(BKL_ENABLE, "bkl_enable"); + gpio_direction_output(BKL_ENABLE, 1); + + /* ethernet reset */ + gpio_request(FEC0_RESET, "enet0_reset"); + gpio_direction_output(FEC0_RESET, 1); +} +#endif + +int checkboard(void) +{ + puts("Board: conga-QMX8\n"); + + build_info(); + print_bootinfo(); + + return 0; +} + +int board_init(void) +{ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + +#ifdef CONFIG_MXC_GPIO + board_gpio_init(); +#endif + +#if (IS_ENABLED(CONFIG_FEC_MXC)) + setup_fec(); +#endif + + return 0; +} + +void detail_board_ddr_info(void) +{ + puts("\nDDR "); +} + +/* + * Board specific reset that is system reset. + */ +void reset_cpu(ulong addr) +{ + /* TODO */ +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, struct bd_info *bd) +{ + return 0; +} +#endif + +int board_mmc_get_env_dev(int devno) +{ + /* Use EMMC */ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + + return devno; +} + +int mmc_map_to_kernel_blk(int dev_no) +{ + /* Use EMMC */ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + + return dev_no; +} + +extern u32 _end_ofs; +int board_late_init(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + env_set("board_name", "QMX8"); + env_set("board_rev", "iMX8QM"); +#endif + + env_set("sec_boot", "no"); +#ifdef CONFIG_AHAB_BOOT + env_set("sec_boot", "yes"); +#endif + +#ifdef CONFIG_ENV_IS_IN_MMC + board_late_mmc_env_init(); +#endif + +#ifdef IMX_LOAD_HDMI_FIMRWARE + char *end_of_uboot; + char command[256]; + + end_of_uboot = (char *)(ulong)(CONFIG_SYS_TEXT_BASE + _end_ofs + + fdt_totalsize(gd->fdt_blob)); + end_of_uboot += 9; + + /* load hdmitxfw.bin and hdmirxfw.bin*/ + memcpy(IMX_HDMI_FIRMWARE_LOAD_ADDR, end_of_uboot, + IMX_HDMITX_FIRMWARE_SIZE + IMX_HDMIRX_FIRMWARE_SIZE); + + sprintf(command, "hdp load 0x%x", IMX_HDMI_FIRMWARE_LOAD_ADDR); + run_command(command, 0); + + sprintf(command, "hdprx load 0x%x", + IMX_HDMI_FIRMWARE_LOAD_ADDR + IMX_HDMITX_FIRMWARE_SIZE); + run_command(command, 0); +#endif + + return 0; +} + +#ifdef CONFIG_FSL_FASTBOOT +#ifdef CONFIG_ANDROID_RECOVERY +int is_recovery_key_pressing(void) +{ + return 0; /*TODO*/ +} +#endif /*CONFIG_ANDROID_RECOVERY*/ +#endif /*CONFIG_FSL_FASTBOOT*/ + +/* Only Enable USB3 resources currently */ +int board_usb_init(int index, enum usb_init_type init) +{ + return 0; +} diff --git a/board/congatec/cgtqmx8/imximage.cfg b/board/congatec/cgtqmx8/imximage.cfg new file mode 100644 index 0000000000..e324c7ca37 --- /dev/null +++ b/board/congatec/cgtqmx8/imximage.cfg @@ -0,0 +1,21 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#define __ASSEMBLY__ + +/* Boot from SD, sector size 0x400 */ +BOOT_FROM SD 0x400 +/* SoC type IMX8QM */ +SOC_TYPE IMX8QM +/* Append seco container image */ +APPEND mx8qm-ahab-container.img +/* Create the 2nd container */ +CONTAINER +/* Add scfw image with exec attribute */ +IMAGE SCU mx8qm-val-scfw-tcm.bin +/* Add ATF image with exec attribute */ +IMAGE A35 bl31.bin 0x80000000 +/* Add U-Boot image with load attribute */ +DATA A35 u-boot-dtb.bin 0x80020000 diff --git a/board/congatec/cgtqmx8/spl.c b/board/congatec/cgtqmx8/spl.c new file mode 100644 index 0000000000..2a5d4c1bcd --- /dev/null +++ b/board/congatec/cgtqmx8/spl.c @@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void spl_board_init(void) +{ + struct udevice *dev; + int offset; + + uclass_find_first_device(UCLASS_MISC, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1, "nxp,imx8-pd"); + while (offset != -FDT_ERR_NOTFOUND) { + lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset), + NULL, true); + offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset, + "nxp,imx8-pd"); + } + + uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + arch_cpu_init(); + + board_early_init_f(); + + timer_init(); + + preloader_console_init(); + + puts("Normal Boot\n"); +} + +#if (IS_ENABLED(CONFIG_SPL_LOAD_FIT)) +int board_fit_config_name_match(const char *name) +{ + /* Just empty function now - can't decide what to choose */ + debug("%s: %s\n", __func__, name); + + return 0; +} +#endif + +void board_init_f(ulong dummy) +{ + /* Clear global data */ + memset((void *)gd, 0, sizeof(gd_t)); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + board_init_r(NULL, 0); +} diff --git a/board/congatec/common/Kconfig b/board/congatec/common/Kconfig new file mode 100644 index 0000000000..5c205bd830 --- /dev/null +++ b/board/congatec/common/Kconfig @@ -0,0 +1,48 @@ +if !ARCH_IMX8M && !ARCH_IMX8 + +config CHAIN_OF_TRUST + depends on !FIT_SIGNATURE && SECURE_BOOT + imply CMD_BLOB + imply CMD_HASH if ARM + select FSL_CAAM + select SPL_BOARD_INIT if (ARM && SPL) + select SHA_HW_ACCEL + select SHA_PROG_HW_ACCEL + select ENV_IS_NOWHERE + select CMD_EXT4 if ARM + select CMD_EXT4_WRITE if ARM + bool + default y + +config CMD_ESBC_VALIDATE + bool "Enable the 'esbc_validate' and 'esbc_halt' commands" + default y if CHAIN_OF_TRUST + help + This option enables two commands used for secure booting: + + esbc_validate - validate signature using RSA verification + esbc_halt - put the core in spin loop (Secure Boot Only) + +endif + +config VOL_MONITOR_LTC3882_READ + depends on VID + bool "Enable the LTC3882 voltage monitor read" + default n + help + This option enables LTC3882 voltage monitor read + functionality. It is used by common VID driver. + +config VOL_MONITOR_LTC3882_SET + depends on VID + bool "Enable the LTC3882 voltage monitor set" + default n + help + This option enables LTC3882 voltage monitor set + functionality. It is used by common VID driver. + +config USB_TCPC + bool "USB Typec port controller simple driver" + default n + help + Enable USB type-c port controller (TCPC) driver diff --git a/board/congatec/common/Makefile b/board/congatec/common/Makefile new file mode 100644 index 0000000000..d4ddfbf971 --- /dev/null +++ b/board/congatec/common/Makefile @@ -0,0 +1,23 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL +# necessary to create built-in.o +obj- := __dummy__.o +else + +obj-y += mmc.o + +endif diff --git a/board/congatec/common/mmc.c b/board/congatec/common/mmc.c new file mode 100644 index 0000000000..bb7a3d4a9a --- /dev/null +++ b/board/congatec/common/mmc.c @@ -0,0 +1,49 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Copyright 2018 NXP + * + */ +#include +#include +#include +#include +#include +#include +#include + +static int check_mmc_autodetect(void) +{ + char *autodetect_str = env_get("mmcautodetect"); + + if ((autodetect_str) && (strcmp(autodetect_str, "yes") == 0)) + return 1; + + return 0; +} + +/* This should be defined for each board */ +__weak int mmc_map_to_kernel_blk(int dev_no) +{ + return dev_no; +} + +void board_late_mmc_env_init(void) +{ + char cmd[32]; + char mmcblk[32]; + u32 dev_no = mmc_get_env_dev(); + + if (!check_mmc_autodetect()) + return; + + env_set_ulong("mmcdev", dev_no); + + /* Set mmcblk env */ + sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", + mmc_map_to_kernel_blk(dev_no)); + env_set("mmcroot", mmcblk); + + sprintf(cmd, "mmc dev %d", dev_no); + run_command(cmd, 0); +} diff --git a/configs/cgtqmx8_defconfig b/configs/cgtqmx8_defconfig new file mode 100644 index 0000000000..238e421601 --- /dev/null +++ b/configs/cgtqmx8_defconfig @@ -0,0 +1,86 @@ +CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y +CONFIG_ARCH_IMX8=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_TARGET_CONGA_QMX8=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/congatec/cgtqmx8/imximage.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_IMX_BOOTAUX=y +CONFIG_LOG=y +CONFIG_SPL_BOARD_INIT=y +CONFIG_HUSH_PARSER=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_CMD_CPU=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_CLK=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FUSE=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx8qm-cgtqmx8" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_ENV_OFFSET=0x400000 +CONFIG_SPL_DM=y +CONFIG_SPL_CLK=y +CONFIG_CLK_IMX8=y +CONFIG_CPU=y +CONFIG_DM_GPIO=y +CONFIG_MXC_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_MISC=y +CONFIG_DM_MMC=y +CONFIG_FSL_USDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_ADDR_ENABLE=y +CONFIG_PHY_ATHEROS=y +CONFIG_DM_ETH=y +CONFIG_PHY_GIGE=y +CONFIG_FEC_MXC_SHARE_MDIO=y +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX8=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_SPL_DM_REGULATOR_GPIO=y +CONFIG_DM_SERIAL=y +CONFIG_FSL_LPUART=y +CONFIG_SPL_TINY_MEMSET=y +# CONFIG_EFI_LOADER is not set +CONFIG_SYS_MMCSD_FS_BOOT_PARTITION=0 +CONFIG_SYS_MMC_ENV_PART=0 +CONFIG_SYS_MMC_ENV_DEV=1 diff --git a/doc/board/congatec/cgtqmx8.rst b/doc/board/congatec/cgtqmx8.rst new file mode 100644 index 0000000000..bccdef2f16 --- /dev/null +++ b/doc/board/congatec/cgtqmx8.rst @@ -0,0 +1,70 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for the Congatec conga-QMX8 board +======================================== + +Quick Start +----------- + +- Build the ARM Trusted firmware binary +- Get scfw_tcm.bin and ahab-container.img +- Get imx-mkimage +- Build U-Boot +- Build imx-mkimage +- Flash the binary into the SD card +- Boot + +Get and Build the ARM Trusted firmware +-------------------------------------- + +.. code-block:: bash + + $ git clone https://source.codeaurora.org/external/imx/imx-atf + $ cd imx-atf/ + $ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga + $ make PLAT=imx8qm bl31 + +Get scfw_tcm.bin and ahab-container.img +--------------------------------------- + +.. code-block:: bash + + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin + $ chmod +x imx-sc-firmware-1.1.bin + $ ./imx-sc-firmware-1.1.bin + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin + $ chmod +x firmware-imx-8.0.bin + $ ./firmware-imx-8.0.bin + +Or use this to avoid running random scripts from the internet, +but note that you must agree to the license the script displays: + +.. code-block:: bash + + $ dd if=imx-sc-firmware-1.1.bin of=imx-sc-firmware-1.1.tar.bz2 bs=37185 skip=1 + $ tar -xf imx-sc-firmware-1.1.tar.bz2 + $ cp imx-sc-firmware-1.1/mx8qx-val-scfw-tcm.bin $(builddir) + + $ dd if=firmware-imx-8.0.bin of=firmware-imx-8.0.tar.bz2 bs=37180 skip=1 + $ tar -xf firmware-imx-8.0.tar.bz2 + $ cp firmware-imx-8.0/firmware/seco/mx8qm-ahab-container.img $(builddir) + +Build U-Boot +------------ + +.. code-block:: bash + + $ export ATF_LOAD_ADDR=0x80000000 + $ export BL33_LOAD_ADDR=0x80020000 + $ make cgtqmx8_defconfig + $ make u-boot.bin + $ make flash.bin + +Flash the binary into the SD card +--------------------------------- + +Burn the flash.bin binary to SD card offset 32KB: + +.. code-block:: bash + + $ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync diff --git a/doc/board/congatec/index.rst b/doc/board/congatec/index.rst new file mode 100644 index 0000000000..cc57b36b2e --- /dev/null +++ b/doc/board/congatec/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Congatec +======== + +.. toctree:: + :maxdepth: 2 + + cgtqmx8.rst diff --git a/doc/board/index.rst b/doc/board/index.rst index a70d2de19d..747511f7dd 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -11,6 +11,7 @@ Board-specific doc AndesTech/index amlogic/index atmel/index + congatec/index coreboot/index emulation/index freescale/index diff --git a/include/configs/cgtqmx8.h b/include/configs/cgtqmx8.h new file mode 100644 index 0000000000..15c50279ad --- /dev/null +++ b/include/configs/cgtqmx8.h @@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2017-2018 NXP + * Copyright 2018 congatec AG + * + */ + +#ifndef __CGTQMX8_H +#define __CGTQMX8_H + +#include +#include + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_TEXT_BASE 0x0 +#define CONFIG_SPL_MAX_SIZE (124 * 1024) +#define CONFIG_SYS_MONITOR_LEN (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x800 + +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x013E000 +#define CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define CONFIG_SERIAL_LPUART_BASE 0x5a060000 +#define CONFIG_MALLOC_F_ADDR 0x00120000 + +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE + +#define CONFIG_OF_EMBED +#endif + +#define CONFIG_REMAKE_ELF + +#define CONFIG_BOARD_EARLY_INIT_F + +/* Flat Device Tree Definitions */ +#define CONFIG_OF_BOARD_SETUP + +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define USDHC1_BASE_ADDR 0x5B010000 +#define USDHC2_BASE_ADDR 0x5B020000 +#define USDHC3_BASE_ADDR 0x5B030000 +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +/* Boot M4 */ +#define M4_BOOT_ENV \ + "m4_0_image=m4_0.bin\0" \ + "m4_1_image=m4_1.bin\0" \ + "loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \ + "loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \ + "m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \ + "m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \ + +#ifdef CONFIG_NAND_BOOT +#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) " +#else +#define MFG_NAND_PARTITION "" +#endif +#define FEC0_RESET IMX_GPIO_NR(2, 5) +#define FEC0_PDOMAIN "conn_enet0" + +#define CONFIG_MFG_ENV_SETTINGS \ + "mfgtool_args=setenv bootargs console=${console},${baudrate} " \ + "rdinit=/linuxrc " \ + "g_mass_storage.stall=0 g_mass_storage.removable=1 " \ + "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\ + "g_mass_storage.iSerialNumber=\"\" "\ + MFG_NAND_PARTITION \ + "clk_ignore_unused "\ + "\0" \ + "initrd_addr=0x83800000\0" \ + "bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \ + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_MFG_ENV_SETTINGS \ + M4_BOOT_ENV \ + "script=boot.scr\0" \ + "image=Image\0" \ + "panel=NULL\0" \ + "console=ttyLP0\0" \ + "fdt_addr=0x83000000\0" \ + "boot_fdt=try\0" \ + "fdt_file=imx8qm-cgt-qmx8.dtb\0" \ + "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \ + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ + "mmcautodetect=yes\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} earlycon\0 " \ + "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "else " \ + "echo wait for boot; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp rw earlycon\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "else " \ + "booti; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else booti ${loadaddr} - ${fdt_addr}; fi" + +/* Link Definitions */ +#define CONFIG_LOADADDR 0x80280000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 + +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 + +#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */ +#define CONFIG_SYS_FSL_USDHC_NUM 3 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024) + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define PHYS_SDRAM_1 0x80000000 +#define PHYS_SDRAM_2 0x880000000 +#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */ +#define PHYS_SDRAM_2_SIZE 0x100000000 /* 4 GB */ + +/* Serial */ +#define CONFIG_BAUDRATE 115200 + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ + +/* Networking */ +#define CONFIG_FEC_MXC_PHYADDR -1 +#define CONFIG_FEC_XCV_TYPE RGMII +#define FEC_QUIRK_ENET_MAC + +#endif /* __CGTQMX8_H */