From: Teresa Remmet Date: Wed, 6 Oct 2021 09:56:52 +0000 (+0200) Subject: board: phytec: phycore-imx8mm: Add SPI-NOR flash support X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=f38b1da8bbef76505f31bb9cd545d833c8499561;p=u-boot.git board: phytec: phycore-imx8mm: Add SPI-NOR flash support Adds SPI-NOR flash support to erase, read and write in bootloader. Signed-off-by: Teresa Remmet --- diff --git a/arch/arm/dts/phycore-imx8mm.dts b/arch/arm/dts/phycore-imx8mm.dts index a4332619e5..e57dfd368d 100644 --- a/arch/arm/dts/phycore-imx8mm.dts +++ b/arch/arm/dts/phycore-imx8mm.dts @@ -54,6 +54,23 @@ }; }; +/* SPI nor flash */ +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi0>; + status = "okay"; + + flash0: norflash@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; +}; + /* i2c eeprom */ &i2c1 { clock-frequency = <400000>; @@ -140,6 +157,17 @@ >; }; + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + >; + }; + pinctrl_i2c1: i2c1grp { fsl,pins = < MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 diff --git a/configs/phycore-imx8mm_defconfig b/configs/phycore-imx8mm_defconfig index 91360b7d1a..6cb2d36855 100644 --- a/configs/phycore-imx8mm_defconfig +++ b/configs/phycore-imx8mm_defconfig @@ -29,6 +29,7 @@ CONFIG_SPL_BOARD_INIT=y CONFIG_SPL_SEPARATE_BSS=y CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_SPL_WATCHDOG=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="u-boot=> " @@ -44,6 +45,7 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_SF_TEST=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y @@ -78,6 +80,20 @@ CONFIG_MMC_UHS_SUPPORT=y CONFIG_MMC_HS400_ES_SUPPORT=y CONFIG_MMC_HS400_SUPPORT=y CONFIG_FSL_ESDHC_IMX=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=3 +CONFIG_SF_DEFAULT_MODE=0x0 +CONFIG_SF_DEFAULT_SPEED=80000000 +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH_WINBOND=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_SPI_FLASH_MTD=y CONFIG_PHYLIB=y CONFIG_PHY_TI_DP83867=y CONFIG_DM_ETH=y @@ -91,6 +107,9 @@ CONFIG_DM_REGULATOR=y CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_GPIO=y CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_NXP_FSPI=y CONFIG_SYSRESET=y CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y