From: Andre Przywara <andre.przywara@arm.com>
Date: Mon, 27 Apr 2020 18:17:59 +0000 (+0100)
Subject: uart: pl011: Add proper DM clock support
X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=e3e2d662a273d5ac67998f390529966a8d8c8a3b;p=u-boot.git

uart: pl011: Add proper DM clock support

Even though the PL011 UART driver claims to be DM compliant, it does not
really a good job with parsing DT nodes. U-Boot seems to adhere to a
non-standard binding, either requiring to have a "skip-init" property in
the node, or to have an extra "clock" property holding the base
*frequency* value for the baud rate generator.
DTs in the U-Boot tree seem to have been hacked to match this
requirement.

The official binding does not mention any of these properties, instead
recommends a standard "clocks" property to point to the baud base clock.

Some boards use simple "fixed-clock" providers, which U-Boot readily
supports, so let's add some simple DM clock code to the PL011 driver to
learn the rate of the first clock, as described by the official binding.

These clock nodes seem to be not ready very early in the boot process,
so provide a fallback value, by re-using the already existing
CONFIG_PL011_CLOCK variable.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add <clock_legacy.h> for get_bus_freq() for layerscape
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---

diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c
index 2a5f256184..6e5d81ce34 100644
--- a/drivers/serial/serial_pl01x.c
+++ b/drivers/serial/serial_pl01x.c
@@ -11,7 +11,10 @@
 /* Simple U-Boot driver for the PrimeCell PL010/PL011 UARTs */
 
 #include <common.h>
+/* For get_bus_freq() */
+#include <clock_legacy.h>
 #include <dm.h>
+#include <clk.h>
 #include <errno.h>
 #include <watchdog.h>
 #include <asm/io.h>
@@ -149,21 +152,24 @@ static int pl01x_generic_setbrg(struct pl01x_regs *regs, enum pl01x_type type,
 		unsigned int remainder;
 		unsigned int fraction;
 
-		/*
-		* Set baud rate
-		*
-		* IBRD = UART_CLK / (16 * BAUD_RATE)
-		* FBRD = RND((64 * MOD(UART_CLK,(16 * BAUD_RATE)))
-		*		/ (16 * BAUD_RATE))
-		*/
-		temp = 16 * baudrate;
-		divider = clock / temp;
-		remainder = clock % temp;
-		temp = (8 * remainder) / baudrate;
-		fraction = (temp >> 1) + (temp & 1);
-
-		writel(divider, &regs->pl011_ibrd);
-		writel(fraction, &regs->pl011_fbrd);
+		/* Without a valid clock rate we cannot set up the baudrate. */
+		if (clock) {
+			/*
+			 * Set baud rate
+			 *
+			 * IBRD = UART_CLK / (16 * BAUD_RATE)
+			 * FBRD = RND((64 * MOD(UART_CLK,(16 * BAUD_RATE)))
+			 *		/ (16 * BAUD_RATE))
+			 */
+			temp = 16 * baudrate;
+			divider = clock / temp;
+			remainder = clock % temp;
+			temp = (8 * remainder) / baudrate;
+			fraction = (temp >> 1) + (temp & 1);
+
+			writel(divider, &regs->pl011_ibrd);
+			writel(fraction, &regs->pl011_fbrd);
+		}
 
 		pl011_set_line_control(regs);
 		/* Finally, enable the UART */
@@ -337,17 +343,28 @@ static const struct udevice_id pl01x_serial_id[] ={
 	{}
 };
 
+#ifndef CONFIG_PL011_CLOCK
+#define CONFIG_PL011_CLOCK 0
+#endif
+
 int pl01x_serial_ofdata_to_platdata(struct udevice *dev)
 {
 	struct pl01x_serial_platdata *plat = dev_get_platdata(dev);
+	struct clk clk;
 	fdt_addr_t addr;
+	int ret;
 
 	addr = devfdt_get_addr(dev);
 	if (addr == FDT_ADDR_T_NONE)
 		return -EINVAL;
 
 	plat->base = addr;
-	plat->clock = dev_read_u32_default(dev, "clock", 1);
+	plat->clock = dev_read_u32_default(dev, "clock", CONFIG_PL011_CLOCK);
+	ret = clk_get_by_index(dev, 0, &clk);
+	if (!ret) {
+		clk_enable(&clk);
+		plat->clock = clk_get_rate(&clk);
+	}
 	plat->type = dev_get_driver_data(dev);
 	plat->skip_init = dev_read_bool(dev, "skip-init");