From: Tom Rini Date: Sat, 15 May 2021 01:34:21 +0000 (-0400) Subject: ppc: Remove MPC8555CDS boards X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=98898601b46920904e63419fa38dd16a3e3b740e;p=u-boot.git ppc: Remove MPC8555CDS boards These boards have not been converted to CONFIG_DM_PCI by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the only ARCH_MPC8555 platform left, remove that support as well. Cc: Priyanka Jain Signed-off-by: Tom Rini --- diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index 0b13856952..891db4e378 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -49,11 +49,6 @@ config TARGET_MPC8548CDS select ARCH_MPC8548 select FSL_VIA -config TARGET_MPC8555CDS - bool "Support MPC8555CDS" - select ARCH_MPC8555 - select FSL_VIA - config TARGET_MPC8568MDS bool "Support MPC8568MDS" select ARCH_MPC8568 @@ -388,14 +383,6 @@ config ARCH_MPC8548 select SYS_PPC_E500_USE_DEBUG_TLB imply CMD_REGINFO -config ARCH_MPC8555 - bool - select FSL_LAW - select SYS_FSL_HAS_DDR1 - select SYS_FSL_HAS_SEC - select SYS_FSL_SEC_BE - select SYS_FSL_SEC_COMPAT_2 - config ARCH_MPC8560 bool select FSL_LAW @@ -948,7 +935,6 @@ config SYS_CCSRBAR_DEFAULT ARCH_MPC8540 || \ ARCH_MPC8544 || \ ARCH_MPC8548 || \ - ARCH_MPC8555 || \ ARCH_MPC8560 || \ ARCH_MPC8568 || \ ARCH_MPC8572 || \ @@ -1179,7 +1165,6 @@ config SYS_FSL_NUM_LAWS ARCH_MPC8548 || \ ARCH_MPC8568 default 8 if ARCH_MPC8540 || \ - ARCH_MPC8555 || \ ARCH_MPC8560 help Number of local access windows. This is fixed per SoC. @@ -1253,7 +1238,7 @@ config SYS_FSL_LBC_CLK_DIV int "Divider of platform clock" depends on FSL_ELBC || ARCH_MPC8540 || \ ARCH_MPC8548 || \ - ARCH_MPC8555 || ARCH_MPC8560 || \ + ARCH_MPC8560 || \ ARCH_MPC8568 default 2 if ARCH_P2041 || \ @@ -1272,7 +1257,6 @@ config FSL_VIA source "board/emulation/qemu-ppce500/Kconfig" source "board/freescale/corenet_ds/Kconfig" source "board/freescale/mpc8548cds/Kconfig" -source "board/freescale/mpc8555cds/Kconfig" source "board/freescale/mpc8568mds/Kconfig" source "board/freescale/p1010rdb/Kconfig" source "board/freescale/p1_p2_rdb_pc/Kconfig" diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index e8126c98f8..610a8ec43f 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -301,8 +301,7 @@ int checkcpu (void) int do_reset(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) { /* Everything after the first generation of PQ3 parts has RSTCR */ -#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8555) || \ - defined(CONFIG_ARCH_MPC8560) +#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560) unsigned long val, msr; /* diff --git a/arch/powerpc/cpu/mpc85xx/pci.c b/arch/powerpc/cpu/mpc85xx/pci.c index 559730181e..b7835c0fee 100644 --- a/arch/powerpc/cpu/mpc85xx/pci.c +++ b/arch/powerpc/cpu/mpc85xx/pci.c @@ -120,29 +120,6 @@ pci_mpc85xx_init(struct pci_controller *board_hose) pci_register_hose(hose); -#if defined(CONFIG_TARGET_MPC8555CDS) - /* - * This is a SW workaround for an apparent HW problem - * in the PCI controller on the MPC85555/41 CDS boards. - * The first config cycle must be to a valid, known - * device on the PCI bus in order to trick the PCI - * controller state machine into a known valid state. - * Without this, the first config cycle has the chance - * of hanging the controller permanently, just leaving - * it in a semi-working state, or leaving it working. - * - * Pick on the Tundra, Device 17, to get it right. - */ - { - u8 header_type; - - pci_hose_read_config_byte(hose, - PCI_BDF(0,BRIDGE_ID,0), - PCI_HEADER_TYPE, - &header_type); - } -#endif - hose->last_busno = pci_hose_scan(hose); #ifdef CONFIG_MPC85XX_PCI2 diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index 90c9fe1af5..26067dd713 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -607,8 +607,7 @@ int get_clocks(void) * for that SOC. This information is taken from application note * AN2919. */ -#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560) || \ - defined(CONFIG_ARCH_MPC8555) +#if defined(CONFIG_ARCH_MPC8540) || defined(CONFIG_ARCH_MPC8560) gd->arch.i2c1_clk = sys_info.freq_systembus; #elif defined(CONFIG_ARCH_MPC8544) /* diff --git a/arch/powerpc/include/asm/cpm_85xx.h b/arch/powerpc/include/asm/cpm_85xx.h index e6f1fab5fb..d42469c6e0 100644 --- a/arch/powerpc/include/asm/cpm_85xx.h +++ b/arch/powerpc/include/asm/cpm_85xx.h @@ -77,13 +77,8 @@ */ #define CPM_DATAONLY_BASE ((uint)128) #define CPM_DP_NOSPACE ((uint)0x7FFFFFFF) -#if defined(CONFIG_ARCH_MPC8555) -#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000) -#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE) -#else /* MPC8540, MPC8560 */ #define CPM_FCC_SPECIAL_BASE ((uint)0x0000B000) #define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE) -#endif /* The number of pages of host memory we allocate for CPM. This is * done early in kernel initialization to get physically contiguous diff --git a/arch/powerpc/include/asm/fsl_lbc.h b/arch/powerpc/include/asm/fsl_lbc.h index ae17608276..3b26451928 100644 --- a/arch/powerpc/include/asm/fsl_lbc.h +++ b/arch/powerpc/include/asm/fsl_lbc.h @@ -325,7 +325,7 @@ void lbc_sdram_init(void); #define LCRR_CLKDIV 0x0000001F #define LCRR_CLKDIV_SHIFT 0 #if defined(CONFIG_MPC83xx) || defined(CONFIG_ARCH_MPC8540) || \ - defined(CONFIG_ARCH_MPC8555) || defined(CONFIG_ARCH_MPC8560) + defined(CONFIG_ARCH_MPC8560) #define LCRR_CLKDIV_2 0x00000002 #define LCRR_CLKDIV_4 0x00000004 #define LCRR_CLKDIV_8 0x00000008 diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index b6770c4cf4..1411b3f38b 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -124,8 +124,7 @@ typedef struct ccsr_i2c { } ccsr_i2c_t; #if defined(CONFIG_ARCH_MPC8540) || \ - defined(CONFIG_ARCH_MPC8548) || \ - defined(CONFIG_ARCH_MPC8555) + defined(CONFIG_ARCH_MPC8548) /* DUART Registers */ typedef struct ccsr_duart { u8 res1[1280]; diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 5d18567332..7862a791ac 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -44,7 +44,6 @@ endif obj-$(CONFIG_FSL_DCU_SII9022A) += dcu_sii9022a.o obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o -obj-$(CONFIG_TARGET_MPC8555CDS) += cds_pci_ft.o obj-$(CONFIG_TARGET_MPC8536DS) += ics307_clk.o obj-$(CONFIG_TARGET_P1022DS) += ics307_clk.o diff --git a/board/freescale/mpc8555cds/Kconfig b/board/freescale/mpc8555cds/Kconfig deleted file mode 100644 index 04bd572212..0000000000 --- a/board/freescale/mpc8555cds/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_MPC8555CDS - -config SYS_BOARD - default "mpc8555cds" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "MPC8555CDS" - -endif diff --git a/board/freescale/mpc8555cds/MAINTAINERS b/board/freescale/mpc8555cds/MAINTAINERS deleted file mode 100644 index 8f32febd91..0000000000 --- a/board/freescale/mpc8555cds/MAINTAINERS +++ /dev/null @@ -1,7 +0,0 @@ -MPC8555CDS BOARD -M: Priyanka Jain -S: Maintained -F: board/freescale/mpc8555cds/ -F: include/configs/MPC8555CDS.h -F: configs/MPC8555CDS_defconfig -F: configs/MPC8555CDS_legacy_defconfig diff --git a/board/freescale/mpc8555cds/Makefile b/board/freescale/mpc8555cds/Makefile deleted file mode 100644 index f121c2fa6b..0000000000 --- a/board/freescale/mpc8555cds/Makefile +++ /dev/null @@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2004 Freescale Semiconductor. -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. - -obj-y += mpc8555cds.o -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/mpc8555cds/ddr.c b/board/freescale/mpc8555cds/ddr.c deleted file mode 100644 index 05c56a85d2..0000000000 --- a/board/freescale/mpc8555cds/ddr.c +++ /dev/null @@ -1,53 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2008 Freescale Semiconductor, Inc. - */ - -#include - -#include -#include - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - /* - * Factors to consider for clock adjust: - * - number of chips on bus - * - position of slot - * - DDR1 vs. DDR2? - * - ??? - * - * This needs to be determined on a board-by-board basis. - * 0110 3/4 cycle late - * 0111 7/8 cycle late - */ - popts->clk_adjust = 6; - - /* - * Factors to consider for CPO: - * - frequency - * - ddr1 vs. ddr2 - */ - popts->cpo_override = 0; - - /* - * Factors to consider for write data delay: - * - number of DIMMs - * - * 1 = 1/4 clock delay - * 2 = 1/2 clock delay - * 3 = 3/4 clock delay - * 4 = 1 clock delay - * 5 = 5/4 clock delay - * 6 = 3/2 clock delay - */ - popts->write_data_delay = 3; - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; -} diff --git a/board/freescale/mpc8555cds/law.c b/board/freescale/mpc8555cds/law.c deleted file mode 100644 index 69f151b615..0000000000 --- a/board/freescale/mpc8555cds/law.c +++ /dev/null @@ -1,41 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include -#include - -/* - * LAW(Local Access Window) configuration: - * - * 0x0000_0000 0x7fff_ffff DDR 2G - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M - * 0xe000_0000 0xe000_ffff CCSR 1M - * 0xe200_0000 0xe20f_ffff PCI1 IO 1M - * 0xe210_0000 0xe21f_ffff PCI2 IO 1M - * 0xf000_0000 0xf7ff_ffff SDRAM 128M - * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M - * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M - * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M - * - * Notes: - * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. - * If flash is 8M at default position (last 8M), no LAW needed. - */ - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI), - SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), - SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_PCI), - SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_PCI_2), - /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ - SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC), -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c deleted file mode 100644 index 3bb8e769c8..0000000000 --- a/board/freescale/mpc8555cds/mpc8555cds.c +++ /dev/null @@ -1,430 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../common/cadmus.h" -#include "../common/eeprom.h" -#include "../common/via.h" - -#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) -extern void ddr_enable_ecc(unsigned int dram_size); -#endif - -void local_bus_init(void); - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */ - /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */ - /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */ - /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */ - /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */ - /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */ - /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */ - /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */ - /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */ - /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */ - /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ - /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ - /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ - /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ - /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */ - /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ - /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ - /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */ - /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ - /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */ - /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */ - /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */ - /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */ - /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ - /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */ - /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */ - /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */ - /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ - /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ - /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ - /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */ - /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */ - /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */ - /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -int checkboard (void) -{ - volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - char buf[32]; - - /* PCI slot in USER bits CSR[6:7] by convention. */ - uint pci_slot = get_pci_slot (); - - uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */ - uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */ - uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */ - uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */ - - uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */ - - uint cpu_board_rev = get_cpu_board_revision (); - - printf ("Board: CDS Version 0x%02x, PCI Slot %d\n", - get_board_version (), pci_slot); - - printf ("CPU Board Revision %d.%d (0x%04x)\n", - MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev), - MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev); - - printf("PCI1: %d bit, %s MHz, %s\n", - (pci1_32) ? 32 : 64, - strmhz(buf, pci1_speed), - pci1_clk_sel ? "sync" : "async"); - - if (pci_dual) { - printf("PCI2: 32 bit, 66 MHz, %s\n", - pci2_clk_sel ? "sync" : "async"); - } else { - printf("PCI2: disabled\n"); - } - - /* - * Initialize local bus. - */ - local_bus_init (); - - return 0; -} - -/* - * Initialize Local Bus - */ -void -local_bus_init(void) -{ - volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; - - uint clkdiv; - uint lbc_hz; - sys_info_t sysinfo; - uint temp_lbcdll; - - /* - * Errata LBC11. - * Fix Local Bus clock glitch when DLL is enabled. - * - * If localbus freq is < 66MHz, DLL bypass mode must be used. - * If localbus freq is > 133MHz, DLL can be safely enabled. - * Between 66 and 133, the DLL is enabled with an override workaround. - */ - - get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & LCRR_CLKDIV; - lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv; - - if (lbc_hz < 66) { - lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */ - - } else if (lbc_hz >= 133) { - lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ - - } else { - lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ - udelay(200); - - /* - * Sample LBC DLL ctrl reg, upshift it to set the - * override bits. - */ - temp_lbcdll = gur->lbcdllcr; - gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000); - asm("sync;isync;msync"); - } -} - -/* - * Initialize SDRAM memory on the Local Bus. - */ -void lbc_sdram_init(void) -{ -#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM) - - uint idx; - volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; - uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE; - uint cpu_board_rev; - uint lsdmr_common; - - puts("LBC SDRAM: "); - print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, - "\n "); - - /* - * Setup SDRAM Base and Option Registers - */ - set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); - set_lbc_br(2, CONFIG_SYS_BR2_PRELIM); - lbc->lbcr = CONFIG_SYS_LBC_LBCR; - asm("msync"); - - lbc->lsrt = CONFIG_SYS_LBC_LSRT; - lbc->mrtpr = CONFIG_SYS_LBC_MRTPR; - asm("msync"); - - /* - * Determine which address lines to use baed on CPU board rev. - */ - cpu_board_rev = get_cpu_board_revision(); - lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON; - if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) { - lsdmr_common |= LSDMR_BSMA1617; - } else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) { - lsdmr_common |= LSDMR_BSMA1516; - } else { - /* - * Assume something unable to identify itself is - * really old, and likely has lines 16/17 mapped. - */ - lsdmr_common |= LSDMR_BSMA1617; - } - - /* - * Issue PRECHARGE ALL command. - */ - lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL; - asm("sync;msync"); - *sdram_addr = 0xff; - ppcDcbf((unsigned long) sdram_addr); - udelay(100); - - /* - * Issue 8 AUTO REFRESH commands. - */ - for (idx = 0; idx < 8; idx++) { - lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH; - asm("sync;msync"); - *sdram_addr = 0xff; - ppcDcbf((unsigned long) sdram_addr); - udelay(100); - } - - /* - * Issue 8 MODE-set command. - */ - lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW; - asm("sync;msync"); - *sdram_addr = 0xff; - ppcDcbf((unsigned long) sdram_addr); - udelay(100); - - /* - * Issue NORMAL OP command. - */ - lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL; - asm("sync;msync"); - *sdram_addr = 0xff; - ppcDcbf((unsigned long) sdram_addr); - udelay(200); /* Overkill. Must wait > 200 bus cycles */ - -#endif /* enable SDRAM init */ -} - -#ifdef CONFIG_PCI -/* For some reason the Tundra PCI bridge shows up on itself as a - * different device. Work around that by refusing to configure it - */ -void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { } - -static struct pci_config_table pci_mpc85xxcds_config_table[] = { - {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}}, - {0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}}, - {0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1, - mpc85xx_config_via_usbide, {0,0,0}}, - {0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2, - mpc85xx_config_via_usb, {0,0,0}}, - {0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3, - mpc85xx_config_via_usb2, {0,0,0}}, - {0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5, - mpc85xx_config_via_power, {0,0,0}}, - {0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6, - mpc85xx_config_via_ac97, {0,0,0}}, - {}, -}; - - -static struct pci_controller hose[] = { - { - config_table: pci_mpc85xxcds_config_table, - }, -#ifdef CONFIG_MPC85XX_PCI2 - {}, -#endif -}; - -#endif - -void -pci_init_board(void) -{ -#ifdef CONFIG_PCI - pci_mpc85xx_init(hose); -#endif -} - -#if defined(CONFIG_OF_BOARD_SETUP) -void -ft_pci_setup(void *blob, struct bd_info *bd) -{ - int node, tmp[2]; - const char *path; - - node = fdt_path_offset(blob, "/aliases"); - tmp[0] = 0; - if (node >= 0) { -#ifdef CONFIG_PCI1 - path = fdt_getprop(blob, node, "pci0", NULL); - if (path) { - tmp[1] = hose[0].last_busno - hose[0].first_busno; - do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); - } -#endif -#ifdef CONFIG_MPC85XX_PCI2 - path = fdt_getprop(blob, node, "pci1", NULL); - if (path) { - tmp[1] = hose[1].last_busno - hose[1].first_busno; - do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); - } -#endif - } -} -#endif diff --git a/board/freescale/mpc8555cds/tlb.c b/board/freescale/mpc8555cds/tlb.c deleted file mode 100644 index 4a18f05af0..0000000000 --- a/board/freescale/mpc8555cds/tlb.c +++ /dev/null @@ -1,95 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* - * TLB 0: 16M Non-cacheable, guarded - * 0xff000000 16M FLASH - * Out of reset this entry is only 4K. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_16M, 1), - - /* - * TLB 1: 256M Non-cacheable, guarded - * 0x80000000 256M PCI1 MEM First half - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 2: 256M Non-cacheable, guarded - * 0x90000000 256M PCI1 MEM Second half - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT + 0x10000000, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 3: 256M Non-cacheable, guarded - * 0xa0000000 256M PCI2 MEM First half - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_VIRT, CONFIG_SYS_PCI2_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 4: 256M Non-cacheable, guarded - * 0xb0000000 256M PCI2 MEM Second half - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_VIRT + 0x10000000, CONFIG_SYS_PCI2_MEM_PHYS + 0x10000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 5: 64M Non-cacheable, guarded - * 0xe000_0000 1M CCSRBAR - * 0xe200_0000 16M PCI1 IO - * 0xe300_0000 16M PCI2 IO - */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_64M, 1), - - /* - * TLB 6: 64M Cacheable, non-guarded - * 0xf000_0000 64M LBC SDRAM - */ - SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 6, BOOKE_PAGESZ_64M, 1), - - /* - * TLB 7: 1M Non-cacheable, guarded - * 0xf8000000 1M CADMUS registers - */ - SET_TLB_ENTRY(1, CADMUS_BASE_ADDR, CADMUS_BASE_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 7, BOOKE_PAGESZ_1M, 1), -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/MPC8555CDS_defconfig b/configs/MPC8555CDS_defconfig deleted file mode 100644 index e7a5ca00b9..0000000000 --- a/configs/MPC8555CDS_defconfig +++ /dev/null @@ -1,40 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xfff80000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_MPC85xx=y -# CONFIG_CMD_ERRATA is not set -CONFIG_TARGET_MPC8555CDS=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -# CONFIG_MISC_INIT_R is not set -CONFIG_HUSH_PARSER=y -CONFIG_CMD_REGINFO=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_PCI=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -# CONFIG_CMD_HASH is not set -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xFFFC0000 -# CONFIG_MMC is not set -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_PHY_ATHEROS=y -CONFIG_PHY_BROADCOM=y -CONFIG_PHY_DAVICOM=y -CONFIG_PHY_LXT=y -CONFIG_PHY_MARVELL=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_SMSC=y -CONFIG_PHY_VITESSE=y -CONFIG_MII=y -CONFIG_TSEC_ENET=y -CONFIG_CONS_INDEX=2 -CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/MPC8555CDS_legacy_defconfig b/configs/MPC8555CDS_legacy_defconfig deleted file mode 100644 index 5780138f85..0000000000 --- a/configs/MPC8555CDS_legacy_defconfig +++ /dev/null @@ -1,41 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xfff80000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_MPC85xx=y -# CONFIG_CMD_ERRATA is not set -CONFIG_TARGET_MPC8555CDS=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="LEGACY" -CONFIG_BOOTDELAY=10 -# CONFIG_MISC_INIT_R is not set -CONFIG_HUSH_PARSER=y -CONFIG_CMD_REGINFO=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_PCI=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -# CONFIG_CMD_HASH is not set -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xFFFC0000 -# CONFIG_MMC is not set -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_PHY_ATHEROS=y -CONFIG_PHY_BROADCOM=y -CONFIG_PHY_DAVICOM=y -CONFIG_PHY_LXT=y -CONFIG_PHY_MARVELL=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_SMSC=y -CONFIG_PHY_VITESSE=y -CONFIG_MII=y -CONFIG_TSEC_ENET=y -CONFIG_CONS_INDEX=2 -CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/drivers/ddr/fsl/ctrl_regs.c b/drivers/ddr/fsl/ctrl_regs.c index b80034478e..b5122d1a1c 100644 --- a/drivers/ddr/fsl/ctrl_regs.c +++ b/drivers/ddr/fsl/ctrl_regs.c @@ -1863,25 +1863,13 @@ static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr) static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) { - unsigned int clk_adjust; /* Clock adjust */ - unsigned int ss_en = 0; /* Source synchronous enable */ - -#if defined(CONFIG_ARCH_MPC8555) - /* Per FSL Application Note: AN2805 */ - ss_en = 1; -#endif - if (fsl_ddr_get_version(0) >= 0x40701) { + if (fsl_ddr_get_version(0) >= 0x40701) /* clk_adjust in 5-bits on T-series and LS-series */ - clk_adjust = (popts->clk_adjust & 0x1F) << 22; - } else { + ddr->ddr_sdram_clk_cntl = (popts->clk_adjust & 0x1F) << 22; + else /* clk_adjust in 4-bits on earlier MPC85xx and P-series */ - clk_adjust = (popts->clk_adjust & 0xF) << 23; - } + ddr->ddr_sdram_clk_cntl = (popts->clk_adjust & 0xF) << 23; - ddr->ddr_sdram_clk_cntl = (0 - | ((ss_en & 0x1) << 31) - | clk_adjust - ); debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl); } diff --git a/drivers/ddr/fsl/mpc85xx_ddr_gen1.c b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c index c642a5b1ee..9c2ddeaf93 100644 --- a/drivers/ddr/fsl/mpc85xx_ddr_gen1.c +++ b/drivers/ddr/fsl/mpc85xx_ddr_gen1.c @@ -48,9 +48,6 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2); out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode); out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval); -#if defined(CONFIG_ARCH_MPC8555) - out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl); -#endif /* * 200 painful micro-seconds must elapse between diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h deleted file mode 100644 index 79e309c95c..0000000000 --- a/include/configs/MPC8555CDS.h +++ /dev/null @@ -1,380 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - */ - -/* - * mpc8555cds board configuration file - * - * Please refer to doc/README.mpc85xxcds for more info. - * - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_CPM2 1 /* has CPM2 */ - -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -#ifndef __ASSEMBLY__ -extern unsigned long get_clock_freq(void); -#endif -#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_SPD - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* Make sure required options are set */ -#ifndef CONFIG_SPD_EEPROM -#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") -#endif - -/* - * Local Bus Definitions - */ - -/* - * FLASH on the Local Bus - * Two banks, 8M each, using the CFI driver. - * Boot from BR0/OR0 bank at 0xff00_0000 - * Alternate BR1/OR1 bank at 0xff80_0000 - * - * BR0, BR1: - * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 - * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 - * Port Size = 16 bits = BRx[19:20] = 10 - * Use GPCM = BRx[24:26] = 000 - * Valid = BRx[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 - * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 - * - * OR0, OR1: - * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 - * Reserved ORx[17:18] = 11, confusion here? - * CSNT = ORx[20] = 1 - * ACS = half cycle delay = ORx[21:22] = 11 - * SCY = 6 = ORx[24:27] = 0110 - * TRLX = use relaxed timing = ORx[29] = 1 - * EAD = use external address latch delay = OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx - */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ - -#define CONFIG_SYS_BR0_PRELIM 0xff801001 -#define CONFIG_SYS_BR1_PRELIM 0xff001001 - -#define CONFIG_SYS_OR0_PRELIM 0xff806e65 -#define CONFIG_SYS_OR1_PRELIM 0xff806e65 - -#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 - * - * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into - * FIXME: the top 17 bits of BR2. - */ - -#define CONFIG_SYS_BR2_PRELIM 0xf0001861 - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_OR2_PRELIM 0xfc006901 - -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ -#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ - -/* - * Common settings for all Local Bus SDRAM commands. - * At run time, either BSMA1516 (for CPU 1.1) - * or BSMA1617 (for CPU 1.0) (old) - * is OR'ed in too. - */ -#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ - | LSDMR_PRETOACT7 \ - | LSDMR_ACTTORW7 \ - | LSDMR_BL8 \ - | LSDMR_WRC4 \ - | LSDMR_CL3 \ - | LSDMR_RFEN \ - ) - -/* - * The CADMUS registers are connected to CS3 on CDS. - * The new memory map places CADMUS at 0xf8000000. - * - * For BR3, need: - * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 - * port-size = 8-bits = BR[19:20] = 01 - * no parity checking = BR[21:22] = 00 - * GPMC for MSEL = BR[24:26] = 000 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 - * - * For OR3, need: - * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 - * disable buffer ctrl OR[19] = 0 - * CSNT OR[20] = 1 - * ACS OR[21:22] = 11 - * XACS OR[23] = 1 - * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe - * SETA OR[28] = 0 - * TRLX OR[29] = 1 - * EHTR OR[30] = 1 - * EAD extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 - */ - -#define CONFIG_FSL_CADMUS - -#define CADMUS_BASE_ADDR 0xf8000000 -#define CONFIG_SYS_BR3_PRELIM 0xf8000801 -#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_CCID -#define CONFIG_SYS_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 -#define CONFIG_SYS_PCI2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ - -#ifdef CONFIG_LEGACY -#define BRIDGE_ID 17 -#define VIA_ID 2 -#else -#define BRIDGE_ID 28 -#define VIA_ID 4 -#endif - -#if defined(CONFIG_PCI) - -#define CONFIG_MPC85XX_PCI2 - - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#endif - -#define CONFIG_IPADDR 192.168.1.253 - -#define CONFIG_HOSTNAME "unknown" -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_BOOTFILE "your.uImage" - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS1\0" \ - "ramdiskaddr=600000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=your.fdt.dtb\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "bootm $loadaddr $ramdiskaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */