From: Tony Dinh Date: Mon, 24 Jan 2022 06:17:12 +0000 (-0800) Subject: arm: kirkwood: Pogoplug-V4 : Add board implementation files X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=7301ed9d68be3e6740aba558c4d70f3339b41600;p=u-boot.git arm: kirkwood: Pogoplug-V4 : Add board implementation files Add board header, defconfig, and implementation files for Pogoplug V4. Signed-off-by: Tony Dinh Reviewed-by: Stefan Roese Reviewed-by: Pali Rohár --- diff --git a/board/cloudengines/pogo_v4/MAINTAINERS b/board/cloudengines/pogo_v4/MAINTAINERS new file mode 100644 index 0000000000..35fd7858b7 --- /dev/null +++ b/board/cloudengines/pogo_v4/MAINTAINERS @@ -0,0 +1,6 @@ +POGO_V4 BOARD +M: Tony Dinh +S: Maintained +F: board/cloudengines/pogo_v4/ +F: include/configs/pogo_v4.h +F: configs/pogo_v4_defconfig diff --git a/board/cloudengines/pogo_v4/Makefile b/board/cloudengines/pogo_v4/Makefile new file mode 100644 index 0000000000..511bf5ff7e --- /dev/null +++ b/board/cloudengines/pogo_v4/Makefile @@ -0,0 +1,10 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2014-2021 Tony Dinh +# +# Based on +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# + +obj-y := pogo_v4.o diff --git a/board/cloudengines/pogo_v4/kwbimage.cfg b/board/cloudengines/pogo_v4/kwbimage.cfg new file mode 100644 index 0000000000..f6294fe313 --- /dev/null +++ b/board/cloudengines/pogo_v4/kwbimage.cfg @@ -0,0 +1,148 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2012 +# David Purdy +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar marvell.com> + +# Boot Media configurations (DONE) +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V (SHOULD BE SAME) +DATA 0xffd100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=3 @ 200MHz (need CL=3 @ 200MHz?) +DATA 0xffd01400 0x43000618 # DDR Configuration register +# bit13-0: 0x200 (200 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xffd01404 0x34143000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xffd01408 0x11012227 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xffd0140c 0x00000819 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xffd01410 0x00000001 # DDR Address Control (changed to Dockstar vals) +# bit1-0: 00, Cs0width=x16 +# bit3-2: 10, Cs0size=512Mb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xffd01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xffd01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xffd0141c 0x00000632 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 (<===== change to CL=3 ?) +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xffd01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xffd01424 0x0000F07F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 0 , no sample stage +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) (DONE) +# bit3-0: 2, ODT0Rd, MODT[0] asserted during read from DRAM CS1 +# bit7-4: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1 +# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xffd01498 0x00000000 # DDR ODT Control (High) (DONE) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xffd0149c 0x0000e803 # CPU ODT Control (DONE) +DATA 0xffd01480 0x00000001 # DDR Initialization Control (DONE) +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/cloudengines/pogo_v4/pogo_v4.c b/board/cloudengines/pogo_v4/pogo_v4.c new file mode 100644 index 0000000000..61ce0d59c7 --- /dev/null +++ b/board/cloudengines/pogo_v4/pogo_v4.c @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2014-2022 Tony Dinh + * + * Based on + * Copyright (C) 2012 David Purdy + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +/* GPIO configuration */ +#define POGO_V4_OE_LOW (~(0)) +#define POGO_V4_OE_HIGH (~(0)) +#define POGO_V4_OE_VAL_LOW BIT(29) +#define POGO_V4_OE_VAL_HIGH 0 + +/* button */ +#define BTN_EJECT 29 + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(POGO_V4_OE_VAL_LOW, + POGO_V4_OE_VAL_HIGH, + POGO_V4_OE_LOW, POGO_V4_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_SATA1_ACTn, + MPP21_SATA0_ACTn, + MPP22_GPIO, /* Green LED */ + MPP23_GPIO, + MPP24_GPIO, /* Red LED */ + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, + MPP29_GPIO, /* Eject button */ + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GPIO, + MPP34_GPIO, + MPP35_GPIO, /* FR6192 has only 36 GPIOs */ + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + + return 0; +} + +int board_eth_init(struct bd_info *bis) +{ + return cpu_eth_init(bis); +} + +int board_late_init(void) +{ + /* Do late init to ensure successful enumeration of XHCI devices */ + pci_init(); + return 0; +} + +int board_init(void) +{ + /* Boot parameters address */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + return 0; +} + +#if CONFIG_IS_ENABLED(BOOTSTAGE) +#define GREEN_LED BIT(22) +#define RED_LED BIT(24) +#define BOTH_LEDS (GREEN_LED | RED_LED) +#define NEITHER_LED 0 + +static void set_leds(u32 leds, u32 blinking) +{ + struct kwgpio_registers *r; + u32 oe; + u32 bl; + + r = (struct kwgpio_registers *)MVEBU_GPIO0_BASE; + oe = readl(&r->oe) | BOTH_LEDS; + writel(oe & ~leds, &r->oe); /* active low */ + bl = readl(&r->blink_en) & ~BOTH_LEDS; + writel(bl | blinking, &r->blink_en); +} + +void show_boot_progress(int val) +{ + switch (val) { + case BOOTSTAGE_ID_RUN_OS: /* booting Linux */ + set_leds(BOTH_LEDS, NEITHER_LED); + break; + case BOOTSTAGE_ID_NET_ETH_START: /* Ethernet initialization */ + set_leds(GREEN_LED, GREEN_LED); + break; + default: + if (val < 0) /* error */ + set_leds(RED_LED, RED_LED); + break; + } +} +#endif diff --git a/configs/pogo_v4_defconfig b/configs/pogo_v4_defconfig new file mode 100644 index 0000000000..5490067b9e --- /dev/null +++ b/configs/pogo_v4_defconfig @@ -0,0 +1,79 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_DCACHE_OFF=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_SYS_THUMB_BUILD=y +CONFIG_ARCH_KIRKWOOD=y +CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_v4/kwbimage.cfg" +CONFIG_SYS_TEXT_BASE=0x600000 +CONFIG_TARGET_POGO_V4=y +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_OFFSET=0xC0000 +CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogoplug-series-4" +CONFIG_IDENT_STRING="\nPogoplug V4" +CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_BOOTSTAGE=y +CONFIG_SHOW_BOOT_PROGRESS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="setenv bootargs ${bootargs_console}; run bootcmd_usb; bootm 0x00800000 0x01100000 0x2c00000" +CONFIG_USE_PREBOOT=y +CONFIG_BOARD_LATE_INIT=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="Pogo_V4> " +CONFIG_CMD_BOOTZ=y +# CONFIG_BOOTM_PLAN9 is not set +# CONFIG_BOOTM_RTEMS is not set +# CONFIG_BOOTM_VXWORKS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_NAND=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SATA=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_SNTP=y +CONFIG_CMD_DNS=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_JFFS2=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nand0=orion_nand" +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)" +CONFIG_CMD_UBI=y +CONFIG_ISO_PARTITION=y +CONFIG_EFI_PARTITION=y +CONFIG_PARTITION_TYPE_GUID=y +CONFIG_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_NAND=y +CONFIG_VERSION_VARIABLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_NETCONSOLE=y +CONFIG_DM=y +CONFIG_SATA_MV=y +CONFIG_KIRKWOOD_GPIO=y +# CONFIG_MMC_HW_PARTITIONING is not set +CONFIG_MVEBU_MMC=y +CONFIG_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_DM_ETH=y +CONFIG_MVGBE=y +CONFIG_MII=y +CONFIG_PCI=y +CONFIG_PCI_MVEBU=y +CONFIG_DM_RTC=y +CONFIG_RTC_EMULATION=y +CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_JFFS2_LZO=y +CONFIG_JFFS2_NAND=y diff --git a/include/configs/pogo_v4.h b/include/configs/pogo_v4.h new file mode 100644 index 0000000000..568a93623d --- /dev/null +++ b/include/configs/pogo_v4.h @@ -0,0 +1,56 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2014-2022 Tony Dinh + * + * Based on + * Copyright (C) 2012 + * David Purdy + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + */ + +#ifndef _CONFIG_POGO_V4_H +#define _CONFIG_POGO_V4_H + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "dtb_file=/boot/dts/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"\ + "mtdids=nand0=orion_nand\0"\ + "bootargs_console=console=ttyS0,115200\0" \ + "bootcmd_usb=usb start; load usb 0:1 0x00800000 /boot/uImage; " \ + "load usb 0:1 0x01100000 /boot/uInitrd; " \ + "load usb 0:1 0x2c00000 $dtb_file\0" + +/* + * Ethernet Driver configuration + */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +#define CONFIG_PHY_BASE_ADR 0 +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ +#endif + +/* + * SATA Driver configuration + */ +#define CONFIG_SYS_SATA_MAX_DEVICE 1 + +/* + * Support large disk for SATA and USB + */ +#define CONFIG_SYS_64BIT_LBA +#define CONFIG_LBA48 + +#endif /* _CONFIG_POGO_V4_H */