From: Adrian Alonso Date: Thu, 6 Aug 2015 20:43:17 +0000 (-0500) Subject: imx: usb: ehci-mx6: add usb support for imx7d soc X-Git-Url: http://git.dujemihanovic.xyz/login.html?a=commitdiff_plain;h=35554fc9a194802a43d50b16e92f4efc7f72bd94;p=u-boot.git imx: usb: ehci-mx6: add usb support for imx7d soc Extend ehci-mx6 usb driver to support imx7d usb Signed-off-by: Adrian Alonso --- diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 7f07d7734a..f70f38c9e8 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -37,6 +37,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o obj-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o obj-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o +obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx6.o obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index 1f5b0560db..54f868420d 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -45,7 +45,10 @@ #define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000 #define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040 - +#define USBNC_OFFSET 0x200 +#define USBNC_PHYSTATUS_ID_DIG (1 << 4) /* otg_id status */ +#define USBNC_PHYCFG2_ACAENB (1 << 4) /* otg_id detection enable */ +#define UCTRL_PM (1 << 9) /* OTG Power Mask */ #define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */ #define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */ @@ -53,6 +56,7 @@ #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */ #define UCMD_RESET (1 << 1) /* controller reset */ +#if defined(CONFIG_MX6) static const unsigned phy_bases[] = { USB_PHY0_BASE_ADDR, USB_PHY1_BASE_ADDR, @@ -153,6 +157,23 @@ static int usb_phy_enable(int index, struct usb_ehci *ehci) return 0; } +int usb_phy_mode(int port) +{ + void __iomem *phy_reg; + void __iomem *phy_ctrl; + u32 val; + + phy_reg = (void __iomem *)phy_bases[port]; + phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); + + val = readl(phy_ctrl); + + if (val & USBPHY_CTRL_OTG_ID) + return USB_INIT_DEVICE; + else + return USB_INIT_HOST; +} + /* Base address for this IP block is 0x02184800 */ struct usbnc_regs { u32 ctrl[4]; /* otg/host1-3 */ @@ -161,12 +182,57 @@ struct usbnc_regs { u32 otg_phy_ctrl_0; u32 uh1_phy_ctrl_0; }; +#elif defined(CONFIG_MX7) +struct usbnc_regs { + u32 ctrl1; + u32 ctrl2; + u32 reserve1[10]; + u32 phy_cfg1; + u32 phy_cfg2; + u32 phy_status; + u32 reserve2[4]; + u32 adp_cfg1; + u32 adp_cfg2; + u32 adp_status; +}; + +static void usb_power_config(int index) +{ + struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + (0x10000 * index) + USBNC_OFFSET); + void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2); + + /* Enable usb_otg_id detection */ + setbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB); +} + +int usb_phy_mode(int port) +{ + struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + (0x10000 * port) + USBNC_OFFSET); + void __iomem *status = (void __iomem *)(&usbnc->phy_status); + u32 val; + + val = readl(status); + + if (val & USBNC_PHYSTATUS_ID_DIG) + return USB_INIT_DEVICE; + else + return USB_INIT_HOST; +} +#endif static void usb_oc_config(int index) { +#if defined(CONFIG_MX6) struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET); void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); +#elif defined(CONFIG_MX7) + struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + (0x10000 * index) + USBNC_OFFSET); + void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1); +#endif #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2 /* mx6qarm2 seems to required a different setting*/ @@ -175,24 +241,11 @@ static void usb_oc_config(int index) setbits_le32(ctrl, UCTRL_OVER_CUR_POL); #endif +#if defined(CONFIG_MX6) setbits_le32(ctrl, UCTRL_OVER_CUR_DIS); -} - -int usb_phy_mode(int port) -{ - void __iomem *phy_reg; - void __iomem *phy_ctrl; - u32 val; - - phy_reg = (void __iomem *)phy_bases[port]; - phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); - - val = readl(phy_ctrl); - - if (val & USBPHY_CTRL_OTG_ID) - return USB_INIT_DEVICE; - else - return USB_INIT_HOST; +#elif defined(CONFIG_MX7) + setbits_le32(ctrl, UCTRL_OVER_CUR_DIS | UCTRL_PM); +#endif } /** @@ -245,8 +298,13 @@ int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { enum usb_init_type type; +#if defined(CONFIG_MX6) + u32 controller_spacing = 0x200; +#elif defined(CONFIG_MX7) + u32 controller_spacing = 0x10000; +#endif struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR + - (0x200 * index)); + (controller_spacing * index)); if (index > 3) return -EINVAL; @@ -258,8 +316,11 @@ int ehci_hcd_init(int index, enum usb_init_type init, usb_power_config(index); usb_oc_config(index); + +#if defined(CONFIG_MX6) usb_internal_phy_clock_gate(index, 1); usb_phy_enable(index, ehci); +#endif type = board_usb_phy_mode(index); *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); @@ -272,6 +333,7 @@ int ehci_hcd_init(int index, enum usb_init_type init, return -ENODEV; if (type == USB_INIT_DEVICE) return 0; + setbits_le32(&ehci->usbmode, CM_HOST); writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc); setbits_le32(&ehci->portsc, USB_EN);