/*
* Virtual <-> DMA view memory address translations
* Again, these are *only* valid on the kernel direct mapped RAM
- * memory. Use of these is *depreciated*.
+ * memory. Use of these is *deprecated*.
*/
#define virt_to_bus(x) (__virt_to_bus((unsigned long)(x)))
#define bus_to_virt(x) ((void *)(__bus_to_virt((unsigned long)(x))))
#endif
/*
- * We should really eliminate virt_to_bus() here - it's depreciated.
+ * We should really eliminate virt_to_bus() here - it's deprecated.
*/
#define page_to_bus(page) (virt_to_bus(page_address(page)))
/* describes where the compressed ramdisk image lives (virtual address) */
/*
* this one accidentally used virtual addresses - as such,
- * its depreciated.
+ * it's deprecated.
*/
#define ATAG_INITRD 0x54410005
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
fsl_ddr_get_spd(spd[i], i, CONFIG_DIMM_SLOTS_PER_CTLR);
- puts("SPD data of all dimms (zero vaule is omitted)...\n");
+ puts("SPD data of all dimms (zero value is omitted)...\n");
puts("Byte (hex) ");
k = 1;
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
}
}
printf("DDR registers dump for all controllers "
- "(zero vaule is omitted)...\n");
+ "(zero value is omitted)...\n");
puts("Offset (hex) ");
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
printf(" Base + 0x%04x", (u32)ddr[i] & 0xFFFF);
#ifdef CONFIG_SPL_OS_BOOT
/*
- * Do board specific preperation before SPL
+ * Do board specific preparation before SPL
* Linux boot
*/
void spl_board_prepare_for_linux(void)
#ifdef CONFIG_SPL_OS_BOOT
/*
- * Do board specific preperation before SPL
+ * Do board specific preparation before SPL
* Linux boot
*/
void spl_board_prepare_for_linux(void)
*
* The "environment" is stored on external storage as a list of '\0'
* terminated "name=value" strings. The end of the list is marked by
- * a double '\0'. The environment is preceeded by a 32 bit CRC over
+ * a double '\0'. The environment is preceded by a 32 bit CRC over
* the data part and, in case of redundant environment, a byte of
* flags.
*
* With "-c" and size is NOT given, then the export command will
* format the data as currently used for the persistent storage,
* i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
- * prepend a valid CRC32 checksum and, in case of resundant
+ * prepend a valid CRC32 checksum and, in case of redundant
* environment, a "current" redundancy flag. If size is given, this
* value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
* checksum and redundancy flag will be inserted.
* terminating '\0' byte) will be written; here the optional size
* argument will be used to make sure not to overflow the user
* provided buffer; the command will abort if the size is not
- * sufficient. Any remainign space will be '\0' padded.
+ * sufficient. Any remaining space will be '\0' padded.
*
* On successful return, the variable "filesize" will be set.
* Note that filesize includes the trailing/terminating '\0' byte(s).
*
- * Usage szenario: create a text snapshot/backup of the current settings:
+ * Usage scenario: create a text snapshot/backup of the current settings:
*
* => env export -t 100000
* => era ${backup_addr} +${filesize}
/*
* env import [-d] [-t [-r] | -b | -c] addr [size]
* -d: delete existing environment before importing;
- * otherwise overwrite / append to existion definitions
+ * otherwise overwrite / append to existing definitions
* -t: assume text format; either "size" must be given or the
* text data must be '\0' terminated
* -r: handle CRLF like LF, that means exported variables with
{
#ifdef CONFIG_SYS_GENERIC_GLOBAL_DATA
/*
- * For some archtectures, global data is initialized and used before
+ * For some architectures, global data is initialized and used before
* calling this function. The data should be preserved. For others,
* CONFIG_SYS_GENERIC_GLOBAL_DATA should be defined and use the stack
* here to host global data until relocation.
/*
* Clear global data before it is accessed at debug print
* in initcall_run_list. Otherwise the debug print probably
- * get the wrong vaule of gd->have_console.
+ * get the wrong value of gd->have_console.
*/
zero_global_data();
#endif
return 0;
}
-/* Emport the environment and generate CRC for it. */
+/* Export the environment and generate CRC for it. */
int env_export(env_t *env_out)
{
char *res;
* to the 256 byte-"opcodes" found on the 8086. The table which
* dispatches this is found in the files optab.[ch].
*
-* Each opcode proc has a comment preceeding it which gives it's table
+* Each opcode proc has a comment preceding it which gives it's table
* address. Several opcodes are missing (undefined) in the table.
*
* Each proc includes information for decoding (DECODE_PRINTF and
/*!
* CAAM page allocation:
* Allocates a partition from secure memory, with the id
- * equal to partion_num. This will de-allocate the page
+ * equal to partition_num. This will de-allocate the page
* if it is already allocated. The partition will have
* full access permissions. The permissions are set before,
* running a job descriptor. A memory page of secure RAM
}
if (mem_mask != 0) {
- /* motib redundent in KW28 */
+ /* motib redundant in KW28 */
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type,
if_id,
CS_ENABLE_REG, 0, 0x8));
* current transfer) have got the time to arrived before
* netloop calls eth_halt
*/
- printf ("About preceeding transfer (eth%d):\n"
+ printf ("About preceding transfer (eth%d):\n"
"- Sent packet number %d\n"
"- Received packet number %d\n"
"- Handled packet number %d\n",
priv = dev_get_priv(bus);
- /* processor special prepartion work */
+ /* processor special preparation work */
cpu_dspi_claim_bus(bus->seq, slave_plat->cs);
/* configure transfer mode */
* shifts the remaining entries to the front. Replacing an entry is a
* combination of deleting the old value and adding the new one.
*
- * The environment is preceeded by a 32 bit CRC over the data part.
+ * The environment is preceded by a 32 bit CRC over the data part.
*
- **************************************************************************
- */
+ *************************************************************************/
#if defined(CONFIG_ENV_IS_IN_FLASH)
# ifndef CONFIG_ENV_ADDR
* 2 data record with 24-bit address
* 3 data record with 32-bit address
* 4 symbol record (LSI extension)
- * 5 number of data records in preceeding block
+ * 5 number of data records in preceding block
* 6 unused
* 7 ending record for S3 records
* 8 ending record for S2 records
*
* If the separator character is different from NUL, then any
* separator characters and backslash characters in the values will
- * be escaped by a preceeding backslash in output. This is needed for
+ * be escaped by a preceding backslash in output. This is needed for
* example to enable multi-line values, especially when the output
* shall later be parsed (for example, for re-import).
*
}
}
-# check for case / default statements not preceeded by break/fallthrough/switch
+# check for case / default statements not preceded by break/fallthrough/switch
if ($line =~ /^.\s*(?:case\s+(?:$Ident|$Constant)\s*|default):/) {
my $has_break = 0;
my $has_statement = 0;
}
if (!$has_break && $has_statement) {
WARN("MISSING_BREAK",
- "Possible switch case/default not preceeded by break or fallthrough comment\n" . $herecurr);
+ "Possible switch case/default not preceded by break or fallthrough comment\n" . $herecurr);
}
}
* The output of this function may or may not be a valid FDT. To ensure it
* is, these disp->flags must be set:
*
- * FDT_REG_SUPERNODES: ensures that subnodes are preceeded by their
+ * FDT_REG_SUPERNODES: ensures that subnodes are preceded by their
* parents. Without this option, fragments of subnode data may be
* output without the supernodes above them. This is useful for
* hashing but cannot produce a valid FDT.
projects / u-boot.git / commitdiff