bool "Support kmcent2"
select VENDOR_KM
-config TARGET_XPEDITE520X
- bool "Support xpedite520x"
- select ARCH_MPC8548
-
-config TARGET_XPEDITE537X
- bool "Support xpedite537x"
- select ARCH_MPC8572
-# Use DDR3 controller with DDR2 DIMMs on this board
- select SYS_FSL_DDRC_GEN3
-
-config TARGET_XPEDITE550X
- bool "Support xpedite550x"
- select ARCH_P2020
-
config TARGET_UCP1020
bool "Support uCP1020"
select ARCH_P1020
select FSL_LAW
select SYS_FSL_HAS_DDR1
-config ARCH_MPC8572
- bool
- select FSL_LAW
- select SYS_FSL_ERRATUM_A004508
- select SYS_FSL_ERRATUM_A005125
- select SYS_FSL_ERRATUM_DDR_115
- select SYS_FSL_ERRATUM_DDR111_DDR134
- select FSL_PCIE_RESET
- select SYS_FSL_HAS_DDR2
- select SYS_FSL_HAS_DDR3
- select SYS_FSL_HAS_SEC
- select SYS_FSL_SEC_BE
- select SYS_FSL_SEC_COMPAT_2
- select SYS_PPC_E500_USE_DEBUG_TLB
- select FSL_ELBC
- imply CMD_NAND
-
config ARCH_P1010
bool
select FSL_LAW
ARCH_T2080
default 2 if ARCH_B4420 || \
ARCH_BSC9132 || \
- ARCH_MPC8572 || \
ARCH_P1020 || \
ARCH_P1021 || \
ARCH_P1023 || \
ARCH_MPC8544 || \
ARCH_MPC8548 || \
ARCH_MPC8560 || \
- ARCH_MPC8572 || \
ARCH_P1010 || \
ARCH_P1011 || \
ARCH_P1020 || \
ARCH_BSC9132 || \
ARCH_C29X || \
ARCH_MPC8536 || \
- ARCH_MPC8572 || \
ARCH_P1010 || \
ARCH_P1011 || \
ARCH_P1020 || \
depends on SYS_PPC_E500_USE_DEBUG_TLB
default 0 if ARCH_MPC8544 || ARCH_MPC8548
default 1 if ARCH_MPC8536
- default 2 if ARCH_MPC8572 || \
- ARCH_P1011 || \
+ default 2 if ARCH_P1011 || \
ARCH_P1020 || \
ARCH_P1021 || \
ARCH_P1024 || \
source "board/freescale/t4rdb/Kconfig"
source "board/keymile/Kconfig"
source "board/socrates/Kconfig"
-source "board/xes/xpedite520x/Kconfig"
-source "board/xes/xpedite537x/Kconfig"
-source "board/xes/xpedite550x/Kconfig"
source "board/Arcturus/ucp1020/Kconfig"
endmenu
obj-$(CONFIG_ARCH_MPC8536) += mpc8536_serdes.o
obj-$(CONFIG_ARCH_MPC8544) += mpc8544_serdes.o
obj-$(CONFIG_ARCH_MPC8548) += mpc8548_serdes.o
-obj-$(CONFIG_ARCH_MPC8572) += mpc8572_serdes.o
obj-$(CONFIG_ARCH_P1010) += p1010_serdes.o
obj-$(CONFIG_ARCH_P1011) += p1021_serdes.o
obj-$(CONFIG_ARCH_P1020) += p1021_serdes.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Freescale Semiconductor, Inc.
- */
-
-#include <config.h>
-#include <common.h>
-#include <log.h>
-#include <asm/io.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-
-#define SRDS1_MAX_LANES 8
-
-static u32 serdes1_prtcl_map;
-
-static u8 serdes1_cfg_tbl[][SRDS1_MAX_LANES] = {
- [0x2] = {PCIE1, PCIE1, PCIE1, PCIE1, NONE, NONE, NONE, NONE},
- [0x3] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2},
- [0x6] = {NONE, NONE, NONE, NONE, SRIO1, SRIO1, SRIO1, SRIO1},
- [0x7] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE3, PCIE3},
- [0xb] = {PCIE1, PCIE1, PCIE1, PCIE1, SRIO1, SRIO1, SRIO1, SRIO1},
- [0xc] = {PCIE1, PCIE1, PCIE1, PCIE1, SRIO1, SRIO1, SRIO1, SRIO1},
- [0xd] = {NONE, NONE, NONE, NONE, SRIO1, SRIO1, SRIO1, SRIO1},
- [0xe] = {NONE, NONE, NONE, NONE, SRIO1, SRIO1, SRIO1, SRIO1},
- [0xf] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1},
-};
-
-int is_serdes_configured(enum srds_prtcl prtcl)
-{
- if (!(serdes1_prtcl_map & (1 << NONE)))
- fsl_serdes_init();
-
- return (1 << prtcl) & serdes1_prtcl_map;
-}
-
-void fsl_serdes_init(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 pordevsr = in_be32(&gur->pordevsr);
- u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
- MPC85xx_PORDEVSR_IO_SEL_SHIFT;
- int lane;
-
- if (serdes1_prtcl_map & (1 << NONE))
- return;
-
- debug("PORDEVSR[IO_SEL_SRDS] = %x\n", srds_cfg);
-
- if (srds_cfg >= ARRAY_SIZE(serdes1_cfg_tbl)) {
- printf("Invalid PORDEVSR[IO_SEL_SRDS] = %d\n", srds_cfg);
- return;
- }
-
- for (lane = 0; lane < SRDS1_MAX_LANES; lane++) {
- enum srds_prtcl lane_prtcl = serdes1_cfg_tbl[srds_cfg][lane];
- serdes1_prtcl_map |= (1 << lane_prtcl);
- }
-
- if (!(pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
- serdes1_prtcl_map |= (1 << SGMII_TSEC1);
-
- if (!(pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
- serdes1_prtcl_map |= (1 << SGMII_TSEC2);
-
- if (!(pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
- serdes1_prtcl_map |= (1 << SGMII_TSEC3);
-
- if (!(pordevsr & MPC85xx_PORDEVSR_SGMII4_DIS))
- serdes1_prtcl_map |= (1 << SGMII_TSEC4);
-
- /* Set the first bit to indicate serdes has been initialized */
- serdes1_prtcl_map |= (1 << NONE);
-}
select ARCH_MPC8641
select BOARD_EARLY_INIT_F
-config TARGET_XPEDITE517X
- bool "Support xpedite517x"
- select ARCH_MPC8641
-
endchoice
config ARCH_MPC8610
If not sure, do not change.
source "board/sbc8641d/Kconfig"
-source "board/xes/xpedite517x/Kconfig"
endmenu
#if defined(CONFIG_ARCH_BSC9131) || defined(CONFIG_ARCH_BSC9132)
LAW_TRGT_IF_OCN_DSP = 0x03,
#else
-#if !defined(CONFIG_ARCH_MPC8572) && !defined(CONFIG_ARCH_P2020)
+#if !defined(CONFIG_ARCH_P2020)
LAW_TRGT_IF_PCIE_3 = 0x03,
#endif
#endif
#define LAW_TRGT_IF_PCIE_1 LAW_TRGT_IF_PCI
#endif
-#if defined(CONFIG_ARCH_MPC8572) || defined(CONFIG_ARCH_P2020)
+#if defined(CONFIG_ARCH_P2020)
#define LAW_TRGT_IF_PCIE_3 LAW_TRGT_IF_PCI
#endif
#endif /* CONFIG_FSL_CORENET */
#define CONFIG_SYS_MPC85xx_PCIX2_OFFSET 0x9000
#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0xa000
#define CONFIG_SYS_MPC85xx_PCIE2_OFFSET 0x9000
-#if defined(CONFIG_ARCH_MPC8572) || defined(CONFIG_ARCH_P2020)
+#if defined(CONFIG_ARCH_P2020)
#define CONFIG_SYS_MPC85xx_PCIE3_OFFSET 0x8000
#else
#define CONFIG_SYS_MPC85xx_PCIE3_OFFSET 0xb000
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
obj-$(CONFIG_FSL_PCI_INIT) += fsl_8xxx_pci.o
-obj-$(CONFIG_ARCH_MPC8572) += fsl_8xxx_clk.o
obj-$(CONFIG_MPC86xx) += fsl_8xxx_clk.o
obj-$(CONFIG_ARCH_P2020) += fsl_8xxx_clk.o
obj-$(CONFIG_MPC85xx) += fsl_8xxx_misc.o board.o
+++ /dev/null
-if TARGET_XPEDITE517X
-
-config SYS_BOARD
- default "xpedite517x"
-
-config SYS_VENDOR
- default "xes"
-
-config SYS_CONFIG_NAME
- default "xpedite517x"
-
-endif
+++ /dev/null
-XPEDITE517X BOARD
-M: Peter Tyser <ptyser@xes-inc.com>
-S: Maintained
-F: board/xes/xpedite517x/
-F: include/configs/xpedite517x.h
-F: configs/xpedite517x_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2001
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += xpedite517x.o
-obj-y += ddr.o
-obj-y += law.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <log.h>
-
-void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
-{
- i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
- sizeof(ddr2_spd_eeprom_t));
-}
-
-/*
- * There are four board-specific SDRAM timing parameters which must be
- * calculated based on the particular PCB artwork. These are:
- * 1.) CPO (Read Capture Delay)
- * - TIMING_CFG_2 register
- * Source: Calculation based on board trace lengths and
- * chip-specific internal delays.
- * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
- * - TIMING_CFG_2 register
- * Source: Calculation based on board trace lengths.
- * Unless clock and DQ lanes are very different
- * lengths (>2"), this should be set to the nominal value
- * of 1/2 clock delay.
- * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
- * - DDR_SDRAM_CLK_CNTL register
- * Source: Signal Integrity Simulations
- * 4.) 2T Timing on Addr/Ctl
- * - TIMING_CFG_2 register
- * Source: Signal Integrity Simulations
- * Usually only needed with heavy load/very high speed (>DDR2-800)
- *
- * PCB routing on the XPedite5170 is nearly identical to the XPedite5370
- * so we use the XPedite5370 settings as a basis for the XPedite5170.
- */
-
-typedef struct board_memctl_options {
- uint16_t datarate_mhz_low;
- uint16_t datarate_mhz_high;
- uint8_t clk_adjust;
- uint8_t cpo_override;
- uint8_t write_data_delay;
-} board_memctl_options_t;
-
-static struct board_memctl_options bopts_ctrl[][2] = {
- {
- /* Controller 0 */
- {
- /* DDR2 600/667 */
- .datarate_mhz_low = 500,
- .datarate_mhz_high = 750,
- .clk_adjust = 5,
- .cpo_override = 8,
- .write_data_delay = 2,
- },
- {
- /* DDR2 800 */
- .datarate_mhz_low = 750,
- .datarate_mhz_high = 850,
- .clk_adjust = 5,
- .cpo_override = 9,
- .write_data_delay = 2,
- },
- },
- {
- /* Controller 1 */
- {
- /* DDR2 600/667 */
- .datarate_mhz_low = 500,
- .datarate_mhz_high = 750,
- .clk_adjust = 5,
- .cpo_override = 7,
- .write_data_delay = 2,
- },
- {
- /* DDR2 800 */
- .datarate_mhz_low = 750,
- .datarate_mhz_high = 850,
- .clk_adjust = 5,
- .cpo_override = 8,
- .write_data_delay = 2,
- },
- },
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
- sys_info_t sysinfo;
- int i;
- unsigned int datarate;
-
- get_sys_info(&sysinfo);
- datarate = get_ddr_freq(0) / 1000000;
-
- for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
- if ((bopts[i].datarate_mhz_low <= datarate) &&
- (bopts[i].datarate_mhz_high >= datarate)) {
- debug("controller %d:\n", ctrl_num);
- debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
- debug(" cpo = %d\n", bopts[i].cpo_override);
- debug(" write_data_delay = %d\n",
- bopts[i].write_data_delay);
- popts->clk_adjust = bopts[i].clk_adjust;
- popts->cpo_override = bopts[i].cpo_override;
- popts->write_data_delay = bopts[i].write_data_delay;
- }
- }
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * Notes:
- * CCSRBAR don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-#ifdef CONFIG_SYS_NAND_BASE
- /* NAND LAW covers 2 NAND flashes */
- SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_512K, LAW_TRGT_IF_LBC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009 Extreme Engineering Solutions, Inc.
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/global_data.h>
-#include <asm/processor.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <fdt_support.h>
-#include <pca953x.h>
-#include "../common/fsl_8xxx_misc.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_PCI)
-extern void ft_board_pci_setup(void *blob, struct bd_info *bd);
-#endif
-
-/*
- * Print out which flash was booted from and if booting from the 2nd flash,
- * swap flash chip selects to maintain consistent flash numbering/addresses.
- */
-static void flash_cs_fixup(void)
-{
- int flash_sel;
-
- /*
- * Print boot dev and swap flash flash chip selects if booted from 2nd
- * flash. Swapping chip selects presents user with a common memory
- * map regardless of which flash was booted from.
- */
- flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
- CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
- printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1);
-
- if (flash_sel) {
- set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
- set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
-
- set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
- set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
- }
-}
-
-int board_early_init_r(void)
-{
- /* Initialize PCA9557 devices */
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0);
-
- flash_cs_fixup();
-
- return 0;
-}
-
-int dram_init(void)
-{
- phys_size_t dram_size = fsl_ddr_sdram();
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /* Initialize and enable DDR ECC */
- ddr_enable_ecc(dram_size);
-#endif
-
- gd->ram_size = dram_size;
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-#ifdef CONFIG_PCI
- ft_board_pci_setup(blob, bd);
-#endif
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif
+++ /dev/null
-if TARGET_XPEDITE520X
-
-config SYS_BOARD
- default "xpedite520x"
-
-config SYS_VENDOR
- default "xes"
-
-config SYS_CONFIG_NAME
- default "xpedite520x"
-
-endif
+++ /dev/null
-XPEDITE520X BOARD
-M: Peter Tyser <ptyser@xes-inc.com>
-S: Maintained
-F: board/xes/xpedite520x/
-F: include/configs/xpedite520x.h
-F: configs/xpedite520x_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2008 Extreme Engineering Solutions, Inc.
-# Copyright 2004 Freescale Semiconductor.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += xpedite520x.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
-{
- i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
-
- /* We use soldered memory, but use an SPD EEPROM to describe it.
- * The SPD has an unspecified dimm type, but the DDR2 initialization
- * code requires a specific type to be specified. This sets the type
- * as a standard unregistered SO-DIMM. */
- if (spd->dimm_type == 0) {
- spd->dimm_type = 0x4;
- ((uchar *)spd)[63] += 0x4;
- }
-}
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 7;
-
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
- */
- popts->cpo_override = 9;
-
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
- */
- popts->write_data_delay = 3;
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
- /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
- SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* W**G* - NOR flashes */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
- /* *I*G* - NAND flash */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1M, 1),
-
-#if CONFIG_PCI1
- /* *I*G* - PCI MEM */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-#endif
-
-#if CONFIG_PCI2
- /* *I*G* - PCI MEM */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_PHYS, CONFIG_SYS_PCI2_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-#endif
-
-#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2)
- /* *I*G* - PCI IO */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_IO_PHYS, CONFIG_SYS_PCI1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_16M, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2004, 2007 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <asm/io.h>
-#include <asm/cache.h>
-#include <asm/mmu.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pca953x.h>
-
-extern void ft_board_pci_setup(void *blob, struct bd_info *bd);
-
-static void flash_cs_fixup(void)
-{
- int flash_sel;
-
- /*
- * Print boot dev and swap flash flash chip selects if booted from 2nd
- * flash. Swapping chip selects presents user with a common memory
- * map regardless of which flash was booted from.
- */
- flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
- CONFIG_SYS_PCA953X_FLASH_PASS_CS));
- printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1);
-
- if (flash_sel) {
- set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
- set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
-
- set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
- set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
- }
-}
-
-int board_early_init_r(void)
-{
- /* Initialize PCA9557 devices */
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
-
- /*
- * Remap NOR flash region to caching-inhibited
- * so that flash can be erased/programmed properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* Invalidate existing TLB entry for NOR flash */
- disable_tlb(0);
- set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1);
-
- flash_cs_fixup();
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-#ifdef CONFIG_PCI
- ft_board_pci_setup(blob, bd);
-#endif
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif
+++ /dev/null
-if TARGET_XPEDITE537X
-
-config SYS_BOARD
- default "xpedite537x"
-
-config SYS_VENDOR
- default "xes"
-
-config SYS_CONFIG_NAME
- default "xpedite537x"
-
-endif
+++ /dev/null
-XPEDITE537X BOARD
-M: Peter Tyser <ptyser@xes-inc.com>
-S: Maintained
-F: board/xes/xpedite537x/
-F: include/configs/xpedite537x.h
-F: configs/xpedite537x_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2008 Extreme Engineering Solutions, Inc.
-# Copyright 2007 Freescale Semiconductor, Inc.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += xpedite537x.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <log.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
-{
- i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
- sizeof(ddr2_spd_eeprom_t));
-}
-
-/*
- * There are four board-specific SDRAM timing parameters which must be
- * calculated based on the particular PCB artwork. These are:
- * 1.) CPO (Read Capture Delay)
- * - TIMING_CFG_2 register
- * Source: Calculation based on board trace lengths and
- * chip-specific internal delays.
- * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
- * - TIMING_CFG_2 register
- * Source: Calculation based on board trace lengths.
- * Unless clock and DQ lanes are very different
- * lengths (>2"), this should be set to the nominal value
- * of 1/2 clock delay.
- * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
- * - DDR_SDRAM_CLK_CNTL register
- * Source: Signal Integrity Simulations
- * 4.) 2T Timing on Addr/Ctl
- * - TIMING_CFG_2 register
- * Source: Signal Integrity Simulations
- * Usually only needed with heavy load/very high speed (>DDR2-800)
- *
- * ====== XPedite5370 DDR2-600 read delay calculations ======
- *
- * See Freescale's App Note AN2583 as refrence. This document also
- * contains the chip-specific delays for 8548E, 8572, etc.
- *
- * For MPC8572E
- * Minimum chip delay (Ch 0): 1.372ns
- * Maximum chip delay (Ch 0): 2.914ns
- * Minimum chip delay (Ch 1): 1.220ns
- * Maximum chip delay (Ch 1): 2.595ns
- *
- * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps
- *
- * Minimum delay calc (Ch 0):
- * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
- * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps
- * = 3808ps
- * = 3.808ns
- *
- * Maximum delay calc (Ch 0):
- * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
- * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps
- * = 6240ps
- * = 6.240ns
- *
- * Minimum delay calc (Ch 1):
- * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
- * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps
- * = 3288ps
- * = 3.288ns
- *
- * Maximum delay calc (Ch 1):
- * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
- * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps
- * = 5536ps
- * = 5.536ns
- *
- * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target)
- * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
- * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target)
- * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7)
- *
- *
- * ====== XPedite5370 DDR2-800 read delay calculations ======
- *
- * See Freescale's App Note AN2583 as refrence. This document also
- * contains the chip-specific delays for 8548E, 8572, etc.
- *
- * For MPC8572E
- * Minimum chip delay (Ch 0): 1.372ns
- * Maximum chip delay (Ch 0): 2.914ns
- * Minimum chip delay (Ch 1): 1.220ns
- * Maximum chip delay (Ch 1): 2.595ns
- *
- * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps
- *
- * Minimum delay calc (Ch 0):
- * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
- * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps
- * = 3341ps
- * = 3.341ns
- *
- * Maximum delay calc (Ch 0):
- * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
- * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps
- * = 5673ps
- * = 5.673ns
- *
- * Minimum delay calc (Ch 1):
- * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
- * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps
- * = 2822ps
- * = 2.822ns
- *
- * Maximum delay calc (Ch 1):
- * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
- * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps
- * = 4968ps
- * = 4.968ns
- *
- * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target)
- * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9)
- * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target)
- * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
- *
- * Write latency (WR_DATA_DELAY) is calculated by doing the following:
- *
- * The DDR SDRAM specification requires DQS be received no sooner than
- * 75% of an SDRAM clock period—and no later than 125% of a clock
- * period—from the capturing clock edge of the command/address at the
- * SDRAM.
- *
- * Based on the above tracelengths, the following are calculated:
- * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns
- * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns
- * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns
- * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns
- *
- * Difference in arrival time CLK vs. DQS:
- * Ch. 0 0.072ns
- * Ch. 1 0.138ns
- *
- * Both of these values are much less than 25% of the clock
- * period at DDR2-600 or DDR2-800, so no additional delay is needed over
- * the 1/2 cycle which normally aligns the first DQS transition
- * exactly WL (CAS latency minus one cycle) after the CAS strobe.
- * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's
- * terminology corresponds to exactly one clock period delay after
- * the CAS strobe. (due to the fact that the "delay" is referenced
- * from the *falling* edge of the CLK, just after the rising edge
- * which the CAS strobe is latched on.
- */
-
-typedef struct board_memctl_options {
- uint16_t datarate_mhz_low;
- uint16_t datarate_mhz_high;
- uint8_t clk_adjust;
- uint8_t cpo_override;
- uint8_t write_data_delay;
-} board_memctl_options_t;
-
-static struct board_memctl_options bopts_ctrl[][2] = {
- {
- /* Controller 0 */
- {
- /* DDR2 600/667 */
- .datarate_mhz_low = 500,
- .datarate_mhz_high = 750,
- .clk_adjust = 5,
- .cpo_override = 8,
- .write_data_delay = 2,
- },
- {
- /* DDR2 800 */
- .datarate_mhz_low = 750,
- .datarate_mhz_high = 850,
- .clk_adjust = 5,
- .cpo_override = 9,
- .write_data_delay = 2,
- },
- },
- {
- /* Controller 1 */
- {
- /* DDR2 600/667 */
- .datarate_mhz_low = 500,
- .datarate_mhz_high = 750,
- .clk_adjust = 5,
- .cpo_override = 7,
- .write_data_delay = 2,
- },
- {
- /* DDR2 800 */
- .datarate_mhz_low = 750,
- .datarate_mhz_high = 850,
- .clk_adjust = 5,
- .cpo_override = 8,
- .write_data_delay = 2,
- },
- },
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
- sys_info_t sysinfo;
- int i;
- unsigned int datarate;
-
- get_sys_info(&sysinfo);
- datarate = sysinfo.freq_ddrbus / 1000 / 1000;
-
- for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
- if ((bopts[i].datarate_mhz_low <= datarate) &&
- (bopts[i].datarate_mhz_high >= datarate)) {
- debug("controller %d:\n", ctrl_num);
- debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
- debug(" cpo = %d\n", bopts[i].cpo_override);
- debug(" write_data_delay = %d\n",
- bopts[i].write_data_delay);
- popts->clk_adjust = bopts[i].clk_adjust;
- popts->cpo_override = bopts[i].cpo_override;
- popts->write_data_delay = bopts[i].write_data_delay;
- }
- }
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* W**G* - NOR flashes */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
- /* *I*G* - NAND flash */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1M, 1),
-
- /* **M** - Boot page for secondary processors */
- SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 3, BOOKE_PAGESZ_4K, 1),
-
-#ifdef CONFIG_PCIE1
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_1G, 1),
-#endif
-
-#ifdef CONFIG_PCIE2
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-#endif
-
-#ifdef CONFIG_PCIE3
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256M, 1),
-#endif
-
-#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_64M, 1),
-#endif
-
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <asm/io.h>
-#include <asm/cache.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pca953x.h>
-
-extern void ft_board_pci_setup(void *blob, struct bd_info *bd);
-
-static void flash_cs_fixup(void)
-{
- int flash_sel;
-
- /*
- * Print boot dev and swap flash flash chip selects if booted from 2nd
- * flash. Swapping chip selects presents user with a common memory
- * map regardless of which flash was booted from.
- */
- flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
- CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
- printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1);
-
- if (flash_sel) {
- set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
- set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
-
- set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
- set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
- }
-}
-
-int board_early_init_r(void)
-{
- /* Initialize PCA9557 devices */
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0);
-
- /*
- * Remap NOR flash region to caching-inhibited
- * so that flash can be erased/programmed properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* Invalidate existing TLB entry for NOR flash */
- disable_tlb(0);
- set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1);
-
- flash_cs_fixup();
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-#ifdef CONFIG_PCI
- ft_board_pci_setup(blob, bd);
-#endif
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif
+++ /dev/null
-if TARGET_XPEDITE550X
-
-config SYS_BOARD
- default "xpedite550x"
-
-config SYS_VENDOR
- default "xes"
-
-config SYS_CONFIG_NAME
- default "xpedite550x"
-
-endif
+++ /dev/null
-XPEDITE550X BOARD
-M: Peter Tyser <ptyser@xes-inc.com>
-S: Maintained
-F: board/xes/xpedite550x/
-F: include/configs/xpedite550x.h
-F: configs/xpedite550x_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2007-2008 Freescale Semiconductor, Inc.
-
-obj-y += xpedite550x.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address)
-{
- i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
- sizeof(ddr3_spd_eeprom_t));
-}
-
-/*
- * There are traditionally three board-specific SDRAM timing parameters
- * which must be calculated based on the particular PCB artwork. These are:
- * 1.) CPO (Read Capture Delay)
- * - TIMING_CFG_2 register
- * Source: Calculation based on board trace lengths and
- * chip-specific internal delays.
- * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
- * - DDR_SDRAM_CLK_CNTL register
- * Source: Signal Integrity Simulations
- * 3.) 2T Timing on Addr/Ctl
- * - TIMING_CFG_2 register
- * Source: Signal Integrity Simulations
- * Usually only needed with heavy load/very high speed (>DDR2-800)
- *
- * ====== XPedite550x DDR3-800 read delay calculations ======
- *
- * The P2020 processor provides an autoleveling option. Setting CPO to
- * 0x1f enables this auto configuration.
- */
-
-typedef struct {
- unsigned short datarate_mhz_low;
- unsigned short datarate_mhz_high;
- unsigned char clk_adjust;
- unsigned char cpo;
-} board_specific_parameters_t;
-
-const board_specific_parameters_t board_specific_parameters[][20] = {
- {
- /* Controller 0 */
- {
- /* DDR3-600/667 */
- .datarate_mhz_low = 500,
- .datarate_mhz_high = 750,
- .clk_adjust = 5,
- .cpo = 31,
- },
- {
- /* DDR3-800 */
- .datarate_mhz_low = 750,
- .datarate_mhz_high = 850,
- .clk_adjust = 5,
- .cpo = 31,
- },
- },
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- const board_specific_parameters_t *pbsp =
- &(board_specific_parameters[ctrl_num][0]);
- u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
- sizeof(board_specific_parameters[0][0]);
- u32 i;
- ulong ddr_freq;
-
- /*
- * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
- * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
- * there are two dimms in the controller, set odt_rd_cfg to 3 and
- * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
- */
- for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
- if (i&1) { /* odd CS */
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 0;
- } else { /* even CS */
- if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 4;
- } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
- popts->cs_local_opts[i].odt_rd_cfg = 3;
- popts->cs_local_opts[i].odt_wr_cfg = 3;
- }
- }
- }
-
- /*
- * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
- * freqency and n_banks specified in board_specific_parameters table.
- */
- ddr_freq = get_ddr_freq(0) / 1000000;
-
- for (i = 0; i < num_params; i++) {
- if (ddr_freq >= pbsp->datarate_mhz_low &&
- ddr_freq <= pbsp->datarate_mhz_high) {
- popts->clk_adjust = pbsp->clk_adjust;
- popts->cpo_override = pbsp->cpo;
- popts->twot_en = 0;
- break;
- }
- pbsp++;
- }
-
- if (i == num_params) {
- printf("Warning: board specific timing not found "
- "for data rate %lu MT/s!\n", ddr_freq);
- }
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-
- /*
- * Enable on-die termination.
- * From the Micron Technical Node TN-41-04, RTT_Nom should typically
- * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR
- * is handled in the Freescale DDR3 driver. Set RTT_Nom here.
- */
- popts->rtt_override = 1;
- popts->rtt_override_value = 3;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* W**G* - NOR flashes */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
- /* *I*G* - NAND flash */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1M, 1),
-
- /* **M** - Boot page for secondary processors */
- SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 3, BOOKE_PAGESZ_4K, 1),
-
-#ifdef CONFIG_PCIE1
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_1G, 1),
-#endif
-
-#ifdef CONFIG_PCIE2
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-#endif
-
-#ifdef CONFIG_PCIE3
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256M, 1),
-#endif
-
-#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
- /* *I*G* - PCIe */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_64M, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Extreme Engineering Solutions, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <asm/io.h>
-#include <asm/cache.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pca953x.h>
-
-extern void ft_board_pci_setup(void *blob, struct bd_info *bd);
-
-static void flash_cs_fixup(void)
-{
- int flash_sel;
-
- /*
- * Print boot dev and swap flash flash chip selects if booted from 2nd
- * flash. Swapping chip selects presents user with a common memory
- * map regardless of which flash was booted from.
- */
- flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
- CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
- printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1);
-
- if (flash_sel) {
- set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
- set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
-
- set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
- set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
- }
-}
-
-int board_early_init_r(void)
-{
- /* Initialize PCA9557 devices */
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0);
- pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0);
-
- /*
- * Remap NOR flash region to caching-inhibited
- * so that flash can be erased/programmed properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* Invalidate existing TLB entry for NOR flash */
- disable_tlb(0);
- set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256M, 1);
-
- flash_cs_fixup();
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-#ifdef CONFIG_PCI
- ft_board_pci_setup(blob, bd);
-#endif
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff00000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC86xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_XPEDITE517X=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_IRQ=y
-CONFIG_ENV_ADDR=0xFFF80000
-CONFIG_CMD_PCA953X=y
-CONFIG_DS4510=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_PANIC_HANG=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_XPEDITE520X=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_JFFS2=y
-# CONFIG_CMD_IRQ is not set
-CONFIG_ENV_ADDR=0xFFF40000
-CONFIG_CMD_PCA953X=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_PANIC_HANG=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_XPEDITE537X=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_JFFS2=y
-# CONFIG_CMD_IRQ is not set
-CONFIG_ENV_ADDR=0xFFF40000
-CONFIG_SYS_FSL_DDR2=y
-CONFIG_CMD_PCA953X=y
-CONFIG_DS4510=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_PANIC_HANG=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_XPEDITE550X=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_JFFS2=y
-# CONFIG_CMD_IRQ is not set
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFF40000
-CONFIG_CMD_PCA953X=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_PANIC_HANG=y
-CONFIG_OF_LIBFDT=y
ARCH_T4240
default 2 if ARCH_B4860 || \
ARCH_BSC9132 || \
- ARCH_MPC8572 || \
ARCH_MPC8641 || \
ARCH_P4080 || \
ARCH_P5040 || \
default y if M548x || M547x || M5282
default y if MCF532x || MCF52x2
default y if MPC86xx || MPC83xx
- default y if ARCH_MPC8572 || ARCH_MPC8548 || ARCH_MPC8641
+ default y if ARCH_MPC8548 || ARCH_MPC8641
default y if SH && !CPU_SH4
help
Define this if you have a flash device which you want to use for the
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2009 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-/*
- * xpedite517x board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_BOARD_NAME "XPedite5170"
-#define CONFIG_SYS_FORM_3U_VPX 1
-#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
-#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
-#define CONFIG_ALTIVEC 1
-
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CONFIG_PCIE1 1 /* PCIE controller 1 */
-#define CONFIG_PCIE2 1 /* PCIE controller 2 */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */
-#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */
-#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
-
-/*
- * virtual address to be used for temporary mappings. There
- * should be 128k free at this VA.
- */
-#define CONFIG_SYS_SCRATCH_VA 0xe0000000
-
-#ifndef __ASSEMBLY__
-#include <linux/stringify.h>
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */
-
-/*
- * L2CR setup
- */
-#define CONFIG_SYS_L2
-#define L2_INIT 0
-#define L2_ENABLE (L2CR_L2E)
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
-
-/*
- * Diagnostics
- */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\
- CONFIG_SYS_POST_I2C)
-/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
-#define I2C_ADDR_IGNORE_LIST {0x50}
-
-/*
- * Memory map
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
- * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable
- * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
- * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
- * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable
- * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
- * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
- * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
- * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
- */
-
-#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3)
-
-/*
- * NAND flash configuration
- */
-#define CONFIG_SYS_NAND_BASE 0xef800000
-#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
-#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define CONFIG_NAND_ACTL
-#define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */
-#define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */
-#define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */
-#define CONFIG_SYS_NAND_ACTL_DELAY 25
-#define CONFIG_JFFS2_NAND
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xf8000000
-#define CONFIG_SYS_FLASH_BASE2 0xf0000000
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \
- {0xf7f00000, 0xc0000} }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
-
-/*
- * Chip select configuration
- */
-/* NOR Flash 0 on CS0 */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
- BR_PS_16 |\
- BR_V)
-#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\
- OR_GPCM_CSNT |\
- OR_GPCM_XACS |\
- OR_GPCM_ACS_DIV2 |\
- OR_GPCM_SCY_8 |\
- OR_GPCM_TRLX |\
- OR_GPCM_EHTR |\
- OR_GPCM_EAD)
-
-/* NOR Flash 1 on CS1 */
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\
- BR_PS_16 |\
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\
- BR_PS_8 |\
- BR_V)
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\
- OR_GPCM_BCTLD |\
- OR_GPCM_CSNT |\
- OR_GPCM_ACS_DIV4 |\
- OR_GPCM_SCY_4 |\
- OR_GPCM_TRLX |\
- OR_GPCM_EHTR)
-
-/* Optional NAND flash on CS3 */
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\
- BR_PS_8 |\
- BR_V)
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-
-/*
- * Use L1 as initial stack
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 100000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 100000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/* PEX8518 slave I2C interface */
-#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
-
-/* I2C DS1631 temperature sensor */
-#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
-
-/* I2C EEPROM - AT24C128B */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/* GPIO */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
-#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
-#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
-#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
-#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
-#define CONFIG_SYS_I2C_PCA9553_ADDR 0x62
-
-/*
- * PU = pulled high, PD = pulled low
- * I = input, O = output, IO = input/output
- */
-/* PCA9557 @ 0x18*/
-#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
-#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */
-
-/* PCA9557 @ 0x1c*/
-#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */
-#define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */
-#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */
-#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */
-#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */
-#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */
-#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */
-#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */
-
-/* PCA9557 @ 0x1e*/
-#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */
-#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */
-
-/* PCA9557 @ 0x1f */
-#define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */
-#define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */
-#define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */
-#define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-/* PCIE1 - PEX8518 */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-/* PCIE2 - VPX P1 */
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */
-
-/*
- * Networking options
- */
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define CONFIG_HAS_ETH0
-
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_PHY_ADDR 2
-#define TSEC2_PHYIDX 0
-#define CONFIG_HAS_ETH1
-
-/*
- * BAT mappings
- */
-#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
-#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\
- BATU_BL_1M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
-#endif
-
-/*
- * BAT0 2G Cacheable, non-guarded
- * 0x0000_0000 2G DDR
- */
-#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
-
-/*
- * BAT1 1G Cache-inhibited, guarded
- * 0x8000_0000 1G PCI-Express 1 Memory
- */
-#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\
- BATU_BL_1G |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
-
-/*
- * BAT2 512M Cache-inhibited, guarded
- * 0xc000_0000 512M PCI-Express 2 Memory
- */
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\
- BATU_BL_512M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
-
-/*
- * BAT3 1M Cache-inhibited, guarded
- * 0xe000_0000 1M CCSR
- */
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\
- BATU_BL_1M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
-
-/*
- * BAT4 32M Cache-inhibited, guarded
- * 0xe200_0000 16M PCI-Express 1 I/O
- * 0xe300_0000 16M PCI-Express 2 I/0
- */
-#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\
- BATU_BL_32M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
-
-/*
- * BAT5 128K Cacheable, non-guarded
- * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory)
- */
-#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\
- BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\
- BATU_BL_128K |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
-#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
-
-/*
- * BAT6 256M Cache-inhibited, guarded
- * 0xf000_0000 256M FLASH
- */
-#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\
- BATU_BL_256M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\
- BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
-
-/* Map the last 1M of flash where we're running from reset */
-#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\
- BATU_BL_1M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
- BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
-
-/*
- * BAT7 64M Cache-inhibited, guarded
- * 0xe800_0000 64K NAND FLASH
- * 0xe804_0000 128K DUART Registers
- */
-#define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\
- BATU_BL_512K |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\
- BATL_PP_RW |\
- BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
-#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-
-/*
- * Flash memory map:
- * fffc0000 - ffffffff Pri FDT (256KB)
- * fff80000 - fffbffff Pri U-Boot Environment (256 KB)
- * fff00000 - fff7ffff Pri U-Boot (512 KB)
- * fef00000 - ffefffff Pri OS image (16MB)
- * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
- *
- * f7fc0000 - f7ffffff Sec FDT (256KB)
- * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB)
- * f7f00000 - f7f7ffff Sec U-Boot (512 KB)
- * f6f00000 - f7efffff Sec OS image (16MB)
- * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
- */
-#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff00000)
-#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f00000)
-#define CONFIG_FDT1_ENV_ADDR __stringify(0xfffc0000)
-#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7fc0000)
-#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
-
-#define CONFIG_PROG_UBOOT1 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_UBOOT2 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_BOOT_OS_NET \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "if test -n $fdtaddr; then " \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "bootm $osaddr - $fdtaddr; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi; " \
- "else; " \
- "bootm $osaddr; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS1 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS2 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT1 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT2 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=yes\0" \
- "download_cmd=tftp\0" \
- "console_args=console=ttyS0,115200\0" \
- "root_args=root=/dev/nfs rw\0" \
- "misc_args=ip=on\0" \
- "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
- "bootfile=/home/user/file\0" \
- "osfile=/home/user/board.uImage\0" \
- "fdtfile=/home/user/board.dtb\0" \
- "ubootfile=/home/user/u-boot.bin\0" \
- "fdtaddr=0x1e00000\0" \
- "osaddr=0x1000000\0" \
- "loadaddr=0x1000000\0" \
- "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
- "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
- "prog_os1="CONFIG_PROG_OS1"\0" \
- "prog_os2="CONFIG_PROG_OS2"\0" \
- "prog_fdt1="CONFIG_PROG_FDT1"\0" \
- "prog_fdt2="CONFIG_PROG_FDT2"\0" \
- "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
- "bootcmd_flash1=run set_bootargs; " \
- "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
- "bootcmd_flash2=run set_bootargs; " \
- "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
- "bootcmd=run bootcmd_flash1\0"
-#endif /* __CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2004-2008 Freescale Semiconductor, Inc.
- */
-
-/*
- * xpedite520x board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_BOARD_NAME "XPedite5200"
-#define CONFIG_SYS_FORM_PMC_XMC 1
-
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CONFIG_PCI1 1 /* PCI controller 1 */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#define SPD_EEPROM_ADDRESS 0x54
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_SYS_CLK_FREQ 66666666
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_CCSRBAR 0xef000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/*
- * Diagnostics
- */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_I2C)
-#define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_PCA953X_ADDR0, \
- CONFIG_SYS_I2C_PCA953X_ADDR1, \
- CONFIG_SYS_I2C_RTC_ADDR}
-
-/*
- * Memory map
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable
- * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
- * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable
- * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
- * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
- * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable
- * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable
- */
-
-#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
-
-/*
- * NAND flash configuration
- */
-#define CONFIG_SYS_NAND_BASE 0xef800000
-#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_ACTL
-#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */
-#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */
-#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */
-#define CONFIG_SYS_NAND_ACTL_DELAY 25
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xfc000000
-#define CONFIG_SYS_FLASH_BASE2 0xf8000000
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
- {0xfbf40000, 0xc0000} }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-/*
- * Chip select configuration
- */
-/* NOR Flash 0 on CS0 */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \
- OR_GPCM_ACS_DIV4 | \
- OR_GPCM_SCY_8)
-
-/* NOR Flash 1 on CS1 */
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
- BR_PS_8 | \
- BR_V)
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
- OR_GPCM_BCTLD | \
- OR_GPCM_CSNT | \
- OR_GPCM_ACS_DIV4 | \
- OR_GPCM_SCY_4 | \
- OR_GPCM_TRLX | \
- OR_GPCM_EHTR)
-
-/* NAND flash on CS3 */
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
- BR_PS_8 | \
- BR_V)
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-
-/*
- * Use L1 as initial stack
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/* I2C EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/* GPIO */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
-#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19
-#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
-
-/* PCA957 @ 0x18 */
-#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01
-#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02
-#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04
-#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08
-#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10
-#define CONFIG_SYS_PCA953X_NVM_WP 0x20
-#define CONFIG_SYS_PCA953X_MONARCH 0x40
-#define CONFIG_SYS_PCA953X_EREADY 0x80
-
-/* PCA957 @ 0x19 */
-#define CONFIG_SYS_PCA953X_P14_IO0 0x01
-#define CONFIG_SYS_PCA953X_P14_IO1 0x02
-#define CONFIG_SYS_PCA953X_P14_IO2 0x04
-#define CONFIG_SYS_PCA953X_P14_IO3 0x08
-#define CONFIG_SYS_PCA953X_P14_IO4 0x10
-#define CONFIG_SYS_PCA953X_P14_IO5 0x20
-#define CONFIG_SYS_PCA953X_P14_IO6 0x40
-#define CONFIG_SYS_PCA953X_P14_IO7 0x80
-
-/* 12-bit ADC used to measure CPU diode */
-#define CONFIG_SYS_I2C_MAX1237_ADDR 0x34
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */
-#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */
-
-/*
- * Networking options
- */
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC1_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define CONFIG_HAS_ETH0
-
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define TSEC2_FLAGS TSEC_GIGABIT
-#define TSEC2_PHY_ADDR 2
-#define TSEC2_PHYIDX 0
-#define CONFIG_HAS_ETH1
-
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-#define TSEC3_FLAGS TSEC_GIGABIT
-#define TSEC3_PHY_ADDR 3
-#define TSEC3_PHYIDX 0
-#define CONFIG_HAS_ETH2
-
-#define CONFIG_TSEC4 1
-#define CONFIG_TSEC4_NAME "eTSEC4"
-#define TSEC4_FLAGS TSEC_GIGABIT
-#define TSEC4_PHY_ADDR 4
-#define TSEC4_PHYIDX 0
-#define CONFIG_HAS_ETH3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
-#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
-#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-
-/*
- * Flash memory map:
- * fff80000 - ffffffff Pri U-Boot (512 KB)
- * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
- * fff00000 - fff3ffff Pri FDT (256KB)
- * fef00000 - ffefffff Pri OS image (16MB)
- * fc000000 - feefffff Pri OS Use/Filesystem (47MB)
- *
- * fbf80000 - fbffffff Sec U-Boot (512 KB)
- * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB)
- * fbf00000 - fbf3ffff Sec FDT (256KB)
- * faf00000 - fbefffff Sec OS image (16MB)
- * f8000000 - faefffff Sec OS Use/Filesystem (47MB)
- */
-#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000)
-#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000)
-#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000)
-
-#define CONFIG_PROG_UBOOT1 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_UBOOT2 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_BOOT_OS_NET \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "if test -n $fdtaddr; then " \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "bootm $osaddr - $fdtaddr; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi; " \
- "else; " \
- "bootm $osaddr; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS1 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS2 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT1 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT2 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=yes\0" \
- "download_cmd=tftp\0" \
- "console_args=console=ttyS0,115200\0" \
- "root_args=root=/dev/nfs rw\0" \
- "misc_args=ip=on\0" \
- "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
- "bootfile=/home/user/file\0" \
- "osfile=/home/user/board.uImage\0" \
- "fdtfile=/home/user/board.dtb\0" \
- "ubootfile=/home/user/u-boot.bin\0" \
- "fdtaddr=0x1e00000\0" \
- "osaddr=0x1000000\0" \
- "loadaddr=0x1000000\0" \
- "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
- "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
- "prog_os1="CONFIG_PROG_OS1"\0" \
- "prog_os2="CONFIG_PROG_OS2"\0" \
- "prog_fdt1="CONFIG_PROG_FDT1"\0" \
- "prog_fdt2="CONFIG_PROG_FDT2"\0" \
- "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
- "bootcmd_flash1=run set_bootargs; " \
- "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
- "bootcmd_flash2=run set_bootargs; " \
- "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
- "bootcmd=run bootcmd_flash1\0"
-#endif /* __CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-/*
- * xpedite537x board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_BOARD_NAME "XPedite5370"
-#define CONFIG_SYS_FORM_3U_VPX 1
-
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CONFIG_PCIE1 1 /* PCIE controller 1 */
-#define CONFIG_PCIE2 1 /* PCIE controller 2 */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-/*
- * Multicore config
- */
-#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
-#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */
-#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */
-#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#ifndef __ASSEMBLY__
-#include <linux/stringify.h>
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-extern unsigned long get_board_ddr_clk(unsigned long dummy);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_CCSRBAR 0xef000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/*
- * Diagnostics
- */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_I2C)
-/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
-#define I2C_ADDR_IGNORE_LIST {0x50}
-
-/*
- * Memory map
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
- * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable
- * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
- * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
- * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable
- * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
- * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
- * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
- * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
- * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
- */
-
-#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
-
-/*
- * NAND flash configuration
- */
-#define CONFIG_SYS_NAND_BASE 0xef800000
-#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
- CONFIG_SYS_NAND_BASE2}
-#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define CONFIG_NAND_FSL_ELBC
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xf8000000
-#define CONFIG_SYS_FLASH_BASE2 0xf0000000
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
- {0xf7f40000, 0xc0000} }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-/*
- * Chip select configuration
- */
-/* NOR Flash 0 on CS0 */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
- OR_GPCM_CSNT | \
- OR_GPCM_XACS | \
- OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_8 | \
- OR_GPCM_TRLX | \
- OR_GPCM_EHTR | \
- OR_GPCM_EAD)
-
-/* NOR Flash 1 on CS1 */
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
- (2<<BR_DECC_SHIFT) | \
- BR_PS_8 | \
- BR_MS_FCM | \
- BR_V)
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
- OR_FCM_PGS | \
- OR_FCM_CSCT | \
- OR_FCM_CST | \
- OR_FCM_CHT | \
- OR_FCM_SCY_1 | \
- OR_FCM_TRLX | \
- OR_FCM_EHTR)
-
-/* NAND flash on CS3 */
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
- (2<<BR_DECC_SHIFT) | \
- BR_PS_8 | \
- BR_MS_FCM | \
- BR_V)
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-
-/*
- * Use L1 as initial stack
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-
-/* PEX8518 slave I2C interface */
-#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
-
-/* I2C DS1631 temperature sensor */
-#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
-
-/* I2C EEPROM - AT24C128B */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/* GPIO */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
-#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
-#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
-#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
-#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
-
-/*
- * PU = pulled high, PD = pulled low
- * I = input, O = output, IO = input/output
- */
-/* PCA9557 @ 0x18*/
-#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
-#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */
-#define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */
-#define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */
-
-/* PCA9557 @ 0x1c*/
-#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */
-#define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */
-#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */
-#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */
-#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */
-#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */
-#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */
-#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */
-
-/* PCA9557 @ 0x1e*/
-#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */
-#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
-
-/* PCA9557 @ 0x1f */
-#define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */
-#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-/* PCIE1 - VPX P1 */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-/* PCIE2 - PEX8518 */
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */
-
-/*
- * Networking options
- */
-#define CONFIG_TSEC_TBI
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_ETHPRIME "eTSEC2"
-
-/*
- * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
- * 1000mbps SGMII link
- */
-#define CONFIG_TSEC_TBICR_SETTINGS ( \
- TBICR_PHY_RESET \
- | TBICR_FULL_DUPLEX \
- | TBICR_SPEED1_SET \
- )
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define CONFIG_HAS_ETH0
-
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_PHY_ADDR 2
-#define TSEC2_PHYIDX 0
-#define CONFIG_HAS_ETH1
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
-#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-
-/*
- * Flash memory map:
- * fff80000 - ffffffff Pri U-Boot (512 KB)
- * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
- * fff00000 - fff3ffff Pri FDT (256KB)
- * fef00000 - ffefffff Pri OS image (16MB)
- * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
- *
- * f7f80000 - f7ffffff Sec U-Boot (512 KB)
- * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
- * f7f00000 - f7f3ffff Sec FDT (256KB)
- * f6f00000 - f7efffff Sec OS image (16MB)
- * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
- */
-#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
-#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
-#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
-
-#define CONFIG_PROG_UBOOT1 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_UBOOT2 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_BOOT_OS_NET \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "if test -n $fdtaddr; then " \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "bootm $osaddr - $fdtaddr; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi; " \
- "else; " \
- "bootm $osaddr; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS1 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS2 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT1 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT2 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=yes\0" \
- "download_cmd=tftp\0" \
- "console_args=console=ttyS0,115200\0" \
- "root_args=root=/dev/nfs rw\0" \
- "misc_args=ip=on\0" \
- "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
- "bootfile=/home/user/file\0" \
- "osfile=/home/user/board.uImage\0" \
- "fdtfile=/home/user/board.dtb\0" \
- "ubootfile=/home/user/u-boot.bin\0" \
- "fdtaddr=0x1e00000\0" \
- "osaddr=0x1000000\0" \
- "loadaddr=0x1000000\0" \
- "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
- "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
- "prog_os1="CONFIG_PROG_OS1"\0" \
- "prog_os2="CONFIG_PROG_OS2"\0" \
- "prog_fdt1="CONFIG_PROG_FDT1"\0" \
- "prog_fdt2="CONFIG_PROG_FDT2"\0" \
- "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
- "bootcmd_flash1=run set_bootargs; " \
- "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
- "bootcmd_flash2=run set_bootargs; " \
- "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
- "bootcmd=run bootcmd_flash1\0"
-#endif /* __CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2010 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-/*
- * xpedite550x board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_BOARD_NAME "XPedite5500"
-#define CONFIG_SYS_FORM_PMC_XMC 1
-#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
-
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CONFIG_PCIE1 1 /* PCIE controller 1 (PEX8112 or XMC) */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-/*
- * Multicore config
- */
-#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
-#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#define SPD_EEPROM_ADDRESS 0x54
-#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#ifndef __ASSEMBLY__
-#include <linux/stringify.h>
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-extern unsigned long get_board_ddr_clk(unsigned long dummy);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_CCSRBAR 0xef000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/*
- * Diagnostics
- */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_I2C)
-#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_LM75_ADDR, \
- CONFIG_SYS_I2C_LM90_ADDR, \
- CONFIG_SYS_I2C_PCA953X_ADDR0, \
- CONFIG_SYS_I2C_PCA953X_ADDR2, \
- CONFIG_SYS_I2C_PCA953X_ADDR3, \
- CONFIG_SYS_I2C_RTC_ADDR}
-
-/*
- * Memory map
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
- * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
- * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
- * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
- * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
- * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
- * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
- * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
- */
-
-#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
-
-/*
- * NAND flash configuration
- */
-#define CONFIG_SYS_NAND_BASE 0xef800000
-#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
- CONFIG_SYS_NAND_BASE2}
-#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define CONFIG_NAND_FSL_ELBC
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xf8000000
-#define CONFIG_SYS_FLASH_BASE2 0xf0000000
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
- {0xf7f40000, 0xc0000} }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-/*
- * Chip select configuration
- */
-/* NOR Flash 0 on CS0 */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
- OR_GPCM_CSNT | \
- OR_GPCM_XACS | \
- OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_8 | \
- OR_GPCM_TRLX | \
- OR_GPCM_EHTR | \
- OR_GPCM_EAD)
-
-/* NOR Flash 1 on CS1 */
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
- BR_PS_16 | \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
- (2<<BR_DECC_SHIFT) | \
- BR_PS_8 | \
- BR_MS_FCM | \
- BR_V)
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
- OR_FCM_PGS | \
- OR_FCM_CSCT | \
- OR_FCM_CST | \
- OR_FCM_CHT | \
- OR_FCM_SCY_1 | \
- OR_FCM_TRLX | \
- OR_FCM_EHTR)
-
-/* NAND flash on CS3 */
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
- (2<<BR_DECC_SHIFT) | \
- BR_PS_8 | \
- BR_MS_FCM | \
- BR_V)
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-
-/*
- * Use L1 as initial stack
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/* I2C DS7505 temperature sensor */
-#define CONFIG_SYS_I2C_LM75_ADDR 0x48
-
-/* I2C ADT7461 temperature sensor */
-#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
-
-/* I2C EEPROM - AT24C128B */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/* GPIO */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
-#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
-#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
-#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
-#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
-
-/*
- * GPIO pin definitions, PU = pulled high, PD = pulled low
- */
-/* PCA9557 @ 0x18*/
-#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
-#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
-#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
-#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
-
-/* PCA9557 @ 0x1e*/
-#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
-#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
-#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
-#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
-#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
-#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
-#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
-
-/* PCA9557 @ 0x1f */
-#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
-#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 1 - PEX8112 or XMC, depending on build option */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-/*
- * Networking options
- */
-#define CONFIG_TSEC_TBI
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_ETHPRIME "eTSEC2"
-
-/*
- * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
- * 1000mbps SGMII link
- */
-#define CONFIG_TSEC_TBICR_SETTINGS ( \
- TBICR_PHY_RESET \
- | TBICR_FULL_DUPLEX \
- | TBICR_SPEED1_SET \
- )
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define CONFIG_HAS_ETH0
-
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_PHY_ADDR 2
-#define TSEC2_PHYIDX 0
-#define CONFIG_HAS_ETH1
-
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_PHY_ADDR 3
-#define TSEC3_PHYIDX 0
-#define CONFIG_HAS_ETH2
-
-/*
- * USB
- */
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
-#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-
-/*
- * Flash memory map:
- * fff80000 - ffffffff Pri U-Boot (512 KB)
- * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
- * fff00000 - fff3ffff Pri FDT (256KB)
- * fef00000 - ffefffff Pri OS image (16MB)
- * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
- *
- * f7f80000 - f7ffffff Sec U-Boot (512 KB)
- * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
- * f7f00000 - f7f3ffff Sec FDT (256KB)
- * f6f00000 - f7efffff Sec OS image (16MB)
- * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
- */
-#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
-#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
-#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
-
-#define CONFIG_PROG_UBOOT1 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_UBOOT2 \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_BOOT_OS_NET \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "if test -n $fdtaddr; then " \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "bootm $osaddr - $fdtaddr; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi; " \
- "else; " \
- "bootm $osaddr; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS1 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS2 \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT1 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT2 \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=yes\0" \
- "download_cmd=tftp\0" \
- "console_args=console=ttyS0,115200\0" \
- "root_args=root=/dev/nfs rw\0" \
- "misc_args=ip=on\0" \
- "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
- "bootfile=/home/user/file\0" \
- "osfile=/home/user/board.uImage\0" \
- "fdtfile=/home/user/board.dtb\0" \
- "ubootfile=/home/user/u-boot.bin\0" \
- "fdtaddr=0x1e00000\0" \
- "osaddr=0x1000000\0" \
- "loadaddr=0x1000000\0" \
- "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
- "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
- "prog_os1="CONFIG_PROG_OS1"\0" \
- "prog_os2="CONFIG_PROG_OS2"\0" \
- "prog_fdt1="CONFIG_PROG_FDT1"\0" \
- "prog_fdt2="CONFIG_PROG_FDT2"\0" \
- "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
- "bootcmd_flash1=run set_bootargs; " \
- "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
- "bootcmd_flash2=run set_bootargs; " \
- "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
- "bootcmd=run bootcmd_flash1\0"
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff