+++ /dev/null
-/*
- * Copyright (C) 2006 Embedded Planet, LLC.
- *
- * Support for Embedded Planet EP82xxM boards.
- * Tested on EP82xxM (MPC8270).
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8260.h>
-#include <ioports.h>
-#include <asm/m8260_pci.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#endif
-#include <miiphy.h>
-#include <linux/compiler.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-#define CONFIG_SYS_FCC2 1
-#define CONFIG_SYS_FCC3 1
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 0, 0, 0, 0, 1 }, /* PA31 */
- /* PA30 */ { 0, 0, 0, 0, 0, 1 }, /* PA30 */
- /* PA29 */ { 0, 0, 0, 0, 0, 1 }, /* PA29 */
- /* PA28 */ { 0, 0, 0, 0, 0, 1 }, /* PA28 */
- /* PA27 */ { 0, 0, 0, 0, 0, 1 }, /* PA27 */
- /* PA26 */ { 0, 0, 0, 0, 0, 1 }, /* PA26 */
- /* PA25 */ { 0, 0, 0, 0, 0, 1 }, /* PA25 */
- /* PA24 */ { 0, 0, 0, 0, 0, 1 }, /* PA24 */
- /* PA23 */ { 0, 0, 0, 0, 0, 1 }, /* PA23 */
- /* PA22 */ { 0, 0, 0, 0, 0, 0 }, /* PA22 */
- /* PA21 */ { 0, 0, 0, 0, 0, 1 }, /* PA21 */
- /* PA20 */ { 0, 0, 0, 0, 0, 1 }, /* PA20 */
- /* PA19 */ { 0, 0, 0, 0, 0, 1 }, /* PA19 */
- /* PA18 */ { 0, 0, 0, 0, 0, 1 }, /* PA18 */
- /* PA17 */ { 0, 0, 0, 0, 0, 1 }, /* PA17 */
- /* PA16 */ { 0, 0, 0, 0, 0, 1 }, /* PA16 */
- /* PA15 */ { 0, 0, 0, 0, 0, 1 }, /* PA15 */
- /* PA14 */ { 0, 0, 0, 0, 0, 1 }, /* PA14 */
- /* PA13 */ { 0, 0, 0, 0, 0, 1 }, /* PA13 */
- /* PA12 */ { 0, 0, 0, 0, 0, 1 }, /* PA12 */
- /* PA11 */ { 0, 0, 0, 0, 0, 1 }, /* PA11 */
- /* PA10 */ { 0, 0, 0, 0, 0, 1 }, /* PA10 */
- /* PA9 */ { 1, 1, 0, 1, 0, 1 }, /* SMC2 TxD */
- /* PA8 */ { 1, 1, 0, 0, 0, 1 }, /* SMC2 RxD */
- /* PA7 */ { 0, 0, 0, 0, 0, 1 }, /* PA7 */
- /* PA6 */ { 0, 0, 0, 0, 0, 1 }, /* PA6 */
- /* PA5 */ { 0, 0, 0, 0, 0, 1 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 0, 0, 1 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 0, 0, 1 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 0, 0, 1 }, /* PA2 */
- /* PA1 */ { 0, 0, 0, 0, 0, 1 }, /* PA1 */
- /* PA0 */ { 0, 0, 0, 0, 0, 1 } /* PA0 */
- },
-
- /* Port B */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { CONFIG_SYS_FCC2, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
- /* PB16 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
- /* PB15 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
- /* PB14 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
- /* PB13 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:COL */
- /* PB12 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
- /* PB11 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB10 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB9 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB8 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */
- /* PB6 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB5 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB4 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */
- /* PC29 */ { 1, 1, 1, 0, 0, 0 }, /* SCC1 CTS# */
- /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */
- /* PC27 */ { CONFIG_SYS_FCC3, 1, 0, 1, 0, 0 }, /* FCC3: TXD[0] */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* PC23 */
- /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* PC22 */
- /* PC21 */ { 0, 0, 0, 0, 0, 0 }, /* PC21 */
- /* PC20 */ { 0, 0, 0, 0, 0, 0 }, /* PC20 */
- /* PC19 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* RxClk (CLK13) */
- /* PC18 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* TxClk (CLK14) */
- /* PC17 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* RxClk (CLK15) */
- /* PC16 */ { CONFIG_SYS_FCC3, 1, 0, 0, 0, 0 }, /* TxClk (CLK16) */
- /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 CD# */
- /* PC13 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 CTS# */
- /* PC12 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 CD# */
- /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */
- /* PC10 */ { 1, 1, 0, 0, 0, 0 }, /* SCC3 CD# */
- /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* PC9 */
- /* PC8 */ { 1, 1, 1, 0, 0, 0 }, /* SCC3 CTS# */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RXD */
- /* PD30 */ { 1, 1, 1, 1, 0, 1 }, /* SCC1 TXD */
- /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 RTS# */
- /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RXD */
- /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 TXD */
- /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 RTS# */
- /* PD25 */ { 1, 1, 0, 0, 0, 0 }, /* SCC3 RXD */
- /* PD24 */ { 1, 1, 0, 1, 0, 0 }, /* SCC3 TXD */
- /* PD23 */ { 1, 1, 0, 1, 0, 0 }, /* SCC3 RTS# */
- /* PD22 */ { 0, 0, 0, 0, 0, 1 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 0, 0, 1 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 0, 0, 1 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 0, 0, 1 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 1 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 1 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 1 }, /* PD16 */
- /* PD15 */ { 1, 1, 1, 0, 1, 1 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 1 }, /* I2C SCL */
- /* PD13 */ { 0, 0, 0, 0, 0, 1 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 1 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 1 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 1 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 1 }, /* SMC1 TxD */
- /* PD8 */ { 1, 1, 0, 0, 0, 1 }, /* SMC1 RxD */
- /* PD7 */ { 1, 1, 0, 0, 0, 1 }, /* SMC1 SMSYN */
- /* PD6 */ { 0, 0, 0, 0, 0, 1 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 1 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 1 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- }
-};
-
-#ifdef CONFIG_PCI
-typedef struct pci_ic_s {
- unsigned long pci_int_stat;
- unsigned long pci_int_mask;
-}pci_ic_t;
-#endif
-
-int board_early_init_f (void)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
-
- bcsr[4] |= 0x30; /* Turn the LEDs off */
-
-#if defined(CONFIG_CONS_ON_SMC) || defined(CONFIG_KGDB_ON_SMC)
- bcsr[6] |= 0x10;
-#endif
-#if defined(CONFIG_CONS_ON_SCC) || defined(CONFIG_KGDB_ON_SCC)
- bcsr[7] |= 0x10;
-#endif
-
-#if CONFIG_SYS_FCC3
- bcsr[8] |= 0xC0;
-#endif /* CONFIG_SYS_FCC3 */
-#if CONFIG_SYS_FCC2
- bcsr[8] |= 0x30;
-#endif /* CONFIG_SYS_FCC2 */
-
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- /* Size in MB of SDRAM populated on board*/
- long int msize = 256;
-
-#ifndef CONFIG_SYS_RAMBOOT
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- uint psdmr = CONFIG_SYS_PSDMR;
- int i;
-
- unsigned char *ramptr1 = (unsigned char *)0x00000110;
- __maybe_unused unsigned char ramtmp;
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
-udelay(400);
-
- /* Initialise 60x bus SDRAM */
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_or1 = CONFIG_SYS_SDRAM_OR;
- memctl->memc_br1 = CONFIG_SYS_SDRAM_BR;
- memctl->memc_psdmr = psdmr;
-
-udelay(400);
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; /* Precharge all banks */
- ramtmp = *ramptr1;
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; /* CBR refresh */
- for (i = 0; i < 8; i++) {
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; /* CBR refresh */
- }
- ramtmp = *ramptr1;
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; /* Mode Register write */
- *ramptr1 = 0xFF;
- memctl->memc_psdmr = psdmr | PSDMR_RFEN; /* Refresh enable */
-#endif /* !CONFIG_SYS_RAMBOOT */
-
- /* Return total 60x bus SDRAM size */
- return msize * 1024 * 1024;
-}
-
-int checkboard(void)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
-
- puts("Board: ");
- switch (bcsr[0]) {
- case 0x0A:
- printf("EP82xxM 1.0 CPLD revision %d\n", bcsr[1]);
- break;
- default:
- printf("unknown: ID=%02X\n", bcsr[0]);
- }
-
- return 0;
-}
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-extern void pci_mpc8250_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc8250_init(&hose);
-}
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2006 Embedded Planet, LLC.
- *
- * U-Boot configuration for Embedded Planet EP82xxM boards.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CPU_ID_STR "MPC8270"
-
-#define CONFIG_EP82XXM /* Embedded Planet EP82xxM H 1.0 board */
- /* 256MB SDRAM / 64MB FLASH */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
-
-#define CONFIG_SYS_BCSR 0xFA000000
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-
-#define CONFIG_ETHER_ON_FCC2
-#define CONFIG_ETHER_ON_FCC3
-
-#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK16)
-#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-
-#define CONFIG_SYS_CPMFCR_RAMTYPE 0
-#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
-
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 0 /* Not used - implemented in BCSR */
-
-#define MDIO_ACTIVE (*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
-#define MDIO_TRISTATE (*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
-#define MDIO_READ (*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
-
-#define MDIO(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
- else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE
-
-#define MDC(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
- else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD
-
-#define MIIDELAY udelay(1)
-
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_VXWORKS_MAC_PTR 0x4300 /* Pass Ethernet MAC to VxWorks */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DIAG
-
-
-#define CONFIG_ETHADDR 00:10:EC:00:88:65
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:10:EC:80:88:65
-#define CONFIG_IPADDR 10.0.0.245
-#define CONFIG_HOSTNAME EP82xxM
-#define CONFIG_SERVERIP 10.0.0.26
-#define CONFIG_GATEWAYIP 10.0.0.1
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_ENV_IN_OWN_SECT 1
-#define CONFIG_AUTO_COMPLETE 1
-#define CONFIG_EXTRA_ENV_SETTINGS "ethprime=FCC3"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "ep82xxm=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-/*
- * Define here the location of the environment variables (FLASH or EEPROM).
- * Note: DENX encourages to use redundant environment in FLASH.
- */
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#else
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0xFC000000
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector in flinfo */
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-/* EEPROM Configuration */
-#define CONFIG_SYS_EEPROM_SIZE 0x1000
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
-#define CONFIG_ENV_OFFSET 0x0
-#endif /* CONFIG_ENV_IS_IN_EEPROM */
-
-/* RTC Configuration */
-#define CONFIG_RTC_M41T11 1 /* uses a M41T81 */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_M41T11_BASE_YEAR 1900
-
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS {0}
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000
-#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_PCI_BOOTDELAY 0
-
-/* PCI Memory map (if different from default map */
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
-#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \
- PICMR_PREFETCH_EN)
-
-/*
- * These are the windows that allow the CPU to access PCI address space.
- * All three PCI master windows, which allow the CPU to access PCI
- * prefetch, non prefetch, and IO space (see below), must all fit within
- * these windows.
- */
-
-/*
- * Master window that allows the CPU to access PCI Memory (prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
-
-/*
- * Master window that allows the CPU to access PCI Memory (non-prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE)
-
-/*
- * Master window that allows the CPU to access PCI IO space.
- * This window will be setup with the first set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF6000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x02000000 /* 64MB */
-#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_32MB | POCMR_ENABLE | POCMR_PCI_IO)
-
-
-/* PCIBR0 - for PCI IO*/
-#define CONFIG_SYS_PCI_MSTR0_LOCAL CONFIG_SYS_PCI_MSTR_IO_LOCAL /* Local base */
-#define CONFIG_SYS_PCIMSK0_MASK ~(CONFIG_SYS_PCI_MSTR_IO_SIZE - 1U) /* Size of window */
-/* PCIBR1 - prefetch and non-prefetch regions joined together */
-#define CONFIG_SYS_PCI_MSTR1_LOCAL CONFIG_SYS_PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCIMSK1_MASK ~(CONFIG_SYS_PCI_MSTR_MEM_SIZE + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE - 1U)
-
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP
-
-#if defined(CONFIG_CMD_JFFS2)
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0
-#define CONFIG_SYS_JFFS2_LAST_SECTOR 62
-#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
-#define CONFIG_SYS_JFFS_CUSTOM_PART
-#endif
-
-#if defined(CONFIG_CMD_I2C)
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 256KB for Monitor */
-
-#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER 0 /*0x1C800641*/ /* Not used - provided by CPLD */
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL 0
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x02610000
-#define CONFIG_SYS_SYPCR 0xFFFF0689
-#define CONFIG_SYS_BCR 0x8080E000
-#define CONFIG_SYS_SCCR 0x00000001
-
-#define CONFIG_SYS_RMR 0
-#define CONFIG_SYS_TMCNTSC 0x000000C3
-#define CONFIG_SYS_PISCR 0x00000083
-#define CONFIG_SYS_RCCR 0
-
-#define CONFIG_SYS_MPTPR 0x0A00
-#define CONFIG_SYS_PSDMR 0xC432246E
-#define CONFIG_SYS_PSRT 0x32
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00000041)
-#define CONFIG_SYS_SDRAM_OR 0xF0002900
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00001801)
-#define CONFIG_SYS_OR0_PRELIM 0xFC000882
-#define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_BCSR | 0x00001001)
-#define CONFIG_SYS_OR4_PRELIM 0xFFF00050
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff