Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
#define AHB_GATE_OFFSET_HDMI 11
#define AHB_GATE_OFFSET_LCD1 5
#define AHB_GATE_OFFSET_LCD0 4
+#define AHB_GATE_OFFSET_TVE1 3
+#define AHB_GATE_OFFSET_TVE0 2
#define CCM_AHB_GATE_GPS (0x1 << 26)
#define CCM_AHB_GATE_SDRAM (0x1 << 14)
#endif
};
+/*
+ * This is based on the A10s User Manual, and the A10s only supports
+ * composite video and not vga like the A10 / A20 does, still other
+ * than the removed vga out capability the tvencoder seems to be the same.
+ * "unknown#" registers are registers which are used in the A10 kernel code,
+ * but not documented in the A10s User Manual.
+ */
+struct sunxi_tve_reg {
+ u32 gctrl; /* 0x000 */
+ u32 cfg0; /* 0x004 */
+ u32 dac_cfg0; /* 0x008 */
+ u32 filter; /* 0x00c */
+ u32 chroma_freq; /* 0x010 */
+ u32 porch_num; /* 0x014 */
+ u32 unknown0; /* 0x018 */
+ u32 line_num; /* 0x01c */
+ u32 blank_black_level; /* 0x020 */
+ u32 unknown1; /* 0x024, seems to be 1 byte per dac */
+ u8 res0[0x08]; /* 0x028 */
+ u32 auto_detect_en; /* 0x030 */
+ u32 auto_detect_int_status; /* 0x034 */
+ u32 auto_detect_status; /* 0x038 */
+ u32 auto_detect_debounce; /* 0x03c */
+ u32 csc_reg0; /* 0x040 */
+ u32 csc_reg1; /* 0x044 */
+ u32 csc_reg2; /* 0x048 */
+ u32 csc_reg3; /* 0x04c */
+ u8 res1[0xb0]; /* 0x050 */
+ u32 color_burst; /* 0x100 */
+ u32 vsync_num; /* 0x104 */
+ u32 notch_freq; /* 0x108 */
+ u32 cbr_level; /* 0x10c */
+ u32 burst_phase; /* 0x110 */
+ u32 burst_width; /* 0x114 */
+ u8 res2[0x04]; /* 0x118 */
+ u32 sync_vbi_level; /* 0x11c */
+ u32 white_level; /* 0x120 */
+ u32 active_num; /* 0x124 */
+ u32 chroma_bw_gain; /* 0x128 */
+ u32 notch_width; /* 0x12c */
+ u32 resync_num; /* 0x130 */
+ u32 slave_para; /* 0x134 */
+ u32 cfg1; /* 0x138 */
+ u32 cfg2; /* 0x13c */
+};
+
/*
* DE-BE register constants.
*/
#define SUNXI_HMDI_DDC_LINE_CTRL_SCL_ENABLE (1 << 8)
#define SUNXI_HMDI_DDC_LINE_CTRL_SDA_ENABLE (1 << 9)
+/*
+ * TVE register constants.
+ */
+#define SUNXI_TVE_GCTRL_ENABLE (1 << 0)
+/*
+ * Select input 0 to disable dac, 1 - 4 to feed dac from tve0, 5 - 8 to feed
+ * dac from tve1. When using tve1 the mux value must be written to both tve0's
+ * and tve1's gctrl reg.
+ */
+#define SUNXI_TVE_GCTRL_DAC_INPUT_MASK(dac) (0xf << (((dac) + 1) * 4))
+#define SUNXI_TVE_GCTRL_DAC_INPUT(dac, sel) ((sel) << (((dac) + 1) * 4))
+#define SUNXI_TVE_GCTRL_CFG0_VGA 0x20000000
+#define SUNXI_TVE_GCTRL_DAC_CFG0_VGA 0x403e1ac7
+#define SUNXI_TVE_GCTRL_UNKNOWN1_VGA 0x00000000
+#define SUNXI_TVE_AUTO_DETECT_EN_DET_EN(dac) (1 << ((dac) + 0))
+#define SUNXI_TVE_AUTO_DETECT_EN_INT_EN(dac) (1 << ((dac) + 16))
+#define SUNXI_TVE_AUTO_DETECT_INT_STATUS(dac) (1 << ((dac) + 0))
+#define SUNXI_TVE_AUTO_DETECT_STATUS_SHIFT(dac) ((dac) * 8)
+#define SUNXI_TVE_AUTO_DETECT_STATUS_MASK(dac) (3 << ((dac) * 8))
+#define SUNXI_TVE_AUTO_DETECT_STATUS_NONE 0
+#define SUNXI_TVE_AUTO_DETECT_STATUS_CONNECTED 1
+#define SUNXI_TVE_AUTO_DETECT_STATUS_SHORT_GND 3
+#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_SHIFT(d) ((d) * 8)
+#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_MASK(d) (0xf << ((d) * 8))
+#define SUNXI_TVE_CSC_REG0_ENABLE (1 << 31)
+#define SUNXI_TVE_CSC_REG0 0x08440832
+#define SUNXI_TVE_CSC_REG1 0x3b6dace1
+#define SUNXI_TVE_CSC_REG2 0x0e1d13dc
+#define SUNXI_TVE_CSC_REG3 0x00108080
+
int sunxi_simplefb_setup(void *blob);
#endif /* _SUNXI_DISPLAY_H */
---help---
Say Y here to add support for outputting video over HDMI.
+config VIDEO_VGA
+ boolean "VGA output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting video over VGA.
+
config VIDEO_VGA_VIA_LCD
boolean "VGA via LCD controller support"
- depends on VIDEO
+ depends on VIDEO && MACH_SUN5I
default n
---help---
Say Y here to add support for external DACs connected to the parallel
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8),USB_EHCI"
CONFIG_FDTFILE="sun7i-a20-olinuxino-micro.dtb"
CONFIG_MMC_SUNXI_SLOT_EXTRA=3
+CONFIG_VIDEO_VGA=y
+S:CONFIG_MMC0_CD_PIN="PH1"
+S:CONFIG_MMC3_CD_PIN="PH11"
+S:CONFIG_ARM=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(12),USB_EHCI"
CONFIG_FDTFILE="sun7i-a20-cubietruck.dtb"
+CONFIG_VIDEO_VGA=y
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_SUNXI=y
+S:CONFIG_MACH_SUN7I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,MACPWR=SUNXI_GPH(15),AHCI,USB_EHCI"
CONFIG_FDTFILE="sun4i-a10-a1000.dtb"
+CONFIG_VIDEO_VGA=y
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_SUNXI=y
+S:CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,MACPWR=SUNXI_GPH(15),AHCI,USB_EHCI"
CONFIG_FDTFILE="sun4i-a10-a1000.dtb"
+CONFIG_VIDEO_VGA=y
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_SUNXI=y
+S:CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,USB_EHCI"
CONFIG_FDTFILE="sun7i-a20-m3.dtb"
+CONFIG_VIDEO_VGA=y
+S:CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+S:CONFIG_MMC0_CD_PIN="PH1"
+S:CONFIG_ARM=y
writel(0, &lcdc->tcon0_io_tristate);
}
-#ifdef CONFIG_VIDEO_HDMI
-
+#if defined CONFIG_VIDEO_HDMI || defined CONFIG_VIDEO_VGA
static void sunxi_lcdc_tcon1_mode_set(const struct ctfb_res_modes *mode,
int *clk_div, int *clk_double,
bool use_portd_hvsync)
}
sunxi_lcdc_pll_set(1, mode->pixclock_khz, clk_div, clk_double);
}
+#endif /* CONFIG_VIDEO_HDMI || defined CONFIG_VIDEO_VGA */
+
+#ifdef CONFIG_VIDEO_HDMI
static void sunxi_hdmi_setup_info_frames(const struct ctfb_res_modes *mode)
{
#endif /* CONFIG_VIDEO_HDMI */
+#ifdef CONFIG_VIDEO_VGA
+
+static void sunxi_vga_mode_set(void)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ struct sunxi_tve_reg * const tve =
+ (struct sunxi_tve_reg *)SUNXI_TVE0_BASE;
+
+ /* Clock on */
+ setbits_le32(&ccm->ahb_gate1, 1 << AHB_GATE_OFFSET_TVE0);
+
+ /* Set TVE in VGA mode */
+ writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(2, 3), &tve->gctrl);
+ writel(SUNXI_TVE_GCTRL_CFG0_VGA, &tve->cfg0);
+ writel(SUNXI_TVE_GCTRL_DAC_CFG0_VGA, &tve->dac_cfg0);
+ writel(SUNXI_TVE_GCTRL_UNKNOWN1_VGA, &tve->unknown1);
+}
+
+static void sunxi_vga_enable(void)
+{
+ struct sunxi_tve_reg * const tve =
+ (struct sunxi_tve_reg *)SUNXI_TVE0_BASE;
+
+ setbits_le32(&tve->gctrl, SUNXI_TVE_GCTRL_ENABLE);
+}
+
+#endif /* CONFIG_VIDEO_VGA */
+
static void sunxi_drc_init(void)
{
#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
static void sunxi_mode_set(const struct ctfb_res_modes *mode,
unsigned int address)
{
+ int __maybe_unused clk_div, clk_double;
+
switch (sunxi_display.monitor) {
case sunxi_monitor_none:
break;
case sunxi_monitor_dvi:
- case sunxi_monitor_hdmi: {
+ case sunxi_monitor_hdmi:
#ifdef CONFIG_VIDEO_HDMI
- int clk_div, clk_double;
sunxi_composer_mode_set(mode, address);
sunxi_lcdc_tcon1_mode_set(mode, &clk_div, &clk_double, 0);
sunxi_hdmi_mode_set(mode, clk_div, clk_double);
sunxi_lcdc_enable();
sunxi_hdmi_enable();
#endif
- }
break;
case sunxi_monitor_lcd:
sunxi_lcdc_panel_enable();
sunxi_lcdc_backlight_enable();
break;
case sunxi_monitor_vga:
-#ifdef CONFIG_VIDEO_VGA_VIA_LCD
+#ifdef CONFIG_VIDEO_VGA
+ sunxi_composer_mode_set(mode, address);
+ sunxi_lcdc_tcon1_mode_set(mode, &clk_div, &clk_double, 1);
+ sunxi_vga_mode_set();
+ sunxi_composer_enable();
+ sunxi_lcdc_enable();
+ sunxi_vga_enable();
+#elif defined CONFIG_VIDEO_VGA_VIA_LCD
sunxi_composer_mode_set(mode, address);
sunxi_lcdc_tcon0_mode_set(mode);
sunxi_composer_enable();
if (lcd_mode[0]) {
sunxi_display.monitor = sunxi_monitor_lcd;
} else {
-#ifdef CONFIG_VIDEO_VGA_VIA_LCD
+#if defined CONFIG_VIDEO_VGA_VIA_LCD || defined CONFIG_VIDEO_VGA
sunxi_display.monitor = sunxi_monitor_vga;
#else
sunxi_display.monitor = sunxi_monitor_none;
sunxi_display.monitor = sunxi_monitor_none;
return NULL;
case sunxi_monitor_vga:
-#ifdef CONFIG_VIDEO_VGA_VIA_LCD
+#if defined CONFIG_VIDEO_VGA_VIA_LCD || defined CONFIG_VIDEO_VGA
sunxi_display.depth = 18;
break;
#else
pipeline = "de_be0-lcd0";
break;
case sunxi_monitor_vga:
+#ifdef CONFIG_VIDEO_VGA
+ pipeline = "de_be0-lcd0-tve0";
+#elif defined CONFIG_VIDEO_VGA_VIA_LCD
pipeline = "de_be0-lcd0";
+#endif
break;
}
projects / u-boot.git / commitdiff