+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2004, 2011 Freescale Semiconductor.
- */
-
-#include <common.h>
-#include <init.h>
-#include <pci.h>
-#include <vsprintf.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <fsl_ddr_sdram.h>
-#include <ioports.h>
-#include <spd_sdram.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-
-#include "../common/cadmus.h"
-#include "../common/eeprom.h"
-#include "../common/via.h"
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
-void local_bus_init(void);
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
- /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
- /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
- /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
- /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
- /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
- /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
- /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
- /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
- /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
- /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
- /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
- /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
- /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
- /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
- /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
- /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
- /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
- /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
- /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
- /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
- /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
- /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
- /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
- /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
- /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
- /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
- /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
- /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
- /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
- /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
- /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
- /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
- /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */
- /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */
- /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
- /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
- /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
- /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
- /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
- /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
- /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- }
-};
-
-int checkboard (void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- char buf[32];
-
- /* PCI slot in USER bits CSR[6:7] by convention. */
- uint pci_slot = get_pci_slot ();
-
- uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */
- uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */
- uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
- uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
-
- uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */
-
- uint cpu_board_rev = get_cpu_board_revision ();
-
- printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
- get_board_version (), pci_slot);
-
- printf ("CPU Board Revision %d.%d (0x%04x)\n",
- MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
- MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
-
- printf("PCI1: %d bit, %s MHz, %s\n",
- (pci1_32) ? 32 : 64,
- strmhz(buf, pci1_speed),
- pci1_clk_sel ? "sync" : "async");
-
- if (pci_dual) {
- printf("PCI2: 32 bit, 66 MHz, %s\n",
- pci2_clk_sel ? "sync" : "async");
- } else {
- printf("PCI2: disabled\n");
- }
-
- /*
- * Initialize local bus.
- */
- local_bus_init ();
-
- return 0;
-}
-
-/*
- * Initialize Local Bus
- */
-void
-local_bus_init(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
- uint clkdiv;
- uint lbc_hz;
- sys_info_t sysinfo;
- uint temp_lbcdll;
-
- /*
- * Errata LBC11.
- * Fix Local Bus clock glitch when DLL is enabled.
- *
- * If localbus freq is < 66MHz, DLL bypass mode must be used.
- * If localbus freq is > 133MHz, DLL can be safely enabled.
- * Between 66 and 133, the DLL is enabled with an override workaround.
- */
-
- get_sys_info(&sysinfo);
- clkdiv = lbc->lcrr & LCRR_CLKDIV;
- lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;
-
- if (lbc_hz < 66) {
- lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */
-
- } else if (lbc_hz >= 133) {
- lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
-
- } else {
- lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
- udelay(200);
-
- /*
- * Sample LBC DLL ctrl reg, upshift it to set the
- * override bits.
- */
- temp_lbcdll = gur->lbcdllcr;
- gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
- asm("sync;isync;msync");
- }
-}
-
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-void lbc_sdram_init(void)
-{
-#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
-
- uint idx;
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
- uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
- uint cpu_board_rev;
- uint lsdmr_common;
-
- puts("LBC SDRAM: ");
- print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
- "\n ");
-
- /*
- * Setup SDRAM Base and Option Registers
- */
- set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
- set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
- lbc->lbcr = CONFIG_SYS_LBC_LBCR;
- asm("msync");
-
- lbc->lsrt = CONFIG_SYS_LBC_LSRT;
- lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
- asm("msync");
-
- /*
- * Determine which address lines to use baed on CPU board rev.
- */
- cpu_board_rev = get_cpu_board_revision();
- lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
- if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
- lsdmr_common |= LSDMR_BSMA1617;
- } else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
- lsdmr_common |= LSDMR_BSMA1516;
- } else {
- /*
- * Assume something unable to identify itself is
- * really old, and likely has lines 16/17 mapped.
- */
- lsdmr_common |= LSDMR_BSMA1617;
- }
-
- /*
- * Issue PRECHARGE ALL command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
-
- /*
- * Issue 8 AUTO REFRESH commands.
- */
- for (idx = 0; idx < 8; idx++) {
- lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
- }
-
- /*
- * Issue 8 MODE-set command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
-
- /*
- * Issue NORMAL OP command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(200); /* Overkill. Must wait > 200 bus cycles */
-
-#endif /* enable SDRAM init */
-}
-
-#ifdef CONFIG_PCI
-/* For some reason the Tundra PCI bridge shows up on itself as a
- * different device. Work around that by refusing to configure it
- */
-void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { }
-
-static struct pci_config_table pci_mpc85xxcds_config_table[] = {
- {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
- {0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}},
- {0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1,
- mpc85xx_config_via_usbide, {0,0,0}},
- {0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2,
- mpc85xx_config_via_usb, {0,0,0}},
- {0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3,
- mpc85xx_config_via_usb2, {0,0,0}},
- {0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5,
- mpc85xx_config_via_power, {0,0,0}},
- {0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6,
- mpc85xx_config_via_ac97, {0,0,0}},
- {},
-};
-
-
-static struct pci_controller hose[] = {
- {
- config_table: pci_mpc85xxcds_config_table,
- },
-#ifdef CONFIG_MPC85XX_PCI2
- {},
-#endif
-};
-
-#endif
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
- pci_mpc85xx_init(hose);
-#endif
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void
-ft_pci_setup(void *blob, struct bd_info *bd)
-{
- int node, tmp[2];
- const char *path;
-
- node = fdt_path_offset(blob, "/aliases");
- tmp[0] = 0;
- if (node >= 0) {
-#ifdef CONFIG_PCI1
- path = fdt_getprop(blob, node, "pci0", NULL);
- if (path) {
- tmp[1] = hose[0].last_busno - hose[0].first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
-#ifdef CONFIG_MPC85XX_PCI2
- path = fdt_getprop(blob, node, "pci1", NULL);
- if (path) {
- tmp[1] = hose[1].last_busno - hose[1].first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
- }
-}
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2004, 2011 Freescale Semiconductor.
- */
-
-/*
- * mpc8555cds board configuration file
- *
- * Please refer to doc/README.mpc85xxcds for more info.
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_CPM2 1 /* has CPM2 */
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_SYS_CCSRBAR 0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
-#endif
-
-/*
- * Local Bus Definitions
- */
-
-/*
- * FLASH on the Local Bus
- * Two banks, 8M each, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff00_0000
- * Alternate BR1/OR1 bank at 0xff80_0000
- *
- * BR0, BR1:
- * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
- * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
- * Port Size = 16 bits = BRx[19:20] = 10
- * Use GPCM = BRx[24:26] = 000
- * Valid = BRx[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
- *
- * OR0, OR1:
- * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
- * Reserved ORx[17:18] = 11, confusion here?
- * CSNT = ORx[20] = 1
- * ACS = half cycle delay = ORx[21:22] = 11
- * SCY = 6 = ORx[24:27] = 0110
- * TRLX = use relaxed timing = ORx[29] = 1
- * EAD = use external address latch delay = OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
- */
-
-#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */
-
-#define CONFIG_SYS_BR0_PRELIM 0xff801001
-#define CONFIG_SYS_BR1_PRELIM 0xff001001
-
-#define CONFIG_SYS_OR0_PRELIM 0xff806e65
-#define CONFIG_SYS_OR1_PRELIM 0xff806e65
-
-#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE}
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- * port-size = 32-bits = BR2[19:20] = 11
- * no parity checking = BR2[21:22] = 00
- * SDRAM for MSEL = BR2[24:26] = 011
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
- *
- * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
- * FIXME: the top 17 bits of BR2.
- */
-
-#define CONFIG_SYS_BR2_PRELIM 0xf0001861
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- * 64MB mask for AM, OR2[0:7] = 1111 1100
- * XAM, OR2[17:18] = 11
- * 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
- * EAD set for extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
- */
-
-#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-
-#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
-
-/*
- * Common settings for all Local Bus SDRAM commands.
- * At run time, either BSMA1516 (for CPU 1.1)
- * or BSMA1617 (for CPU 1.0) (old)
- * is OR'ed in too.
- */
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
- | LSDMR_PRETOACT7 \
- | LSDMR_ACTTORW7 \
- | LSDMR_BL8 \
- | LSDMR_WRC4 \
- | LSDMR_CL3 \
- | LSDMR_RFEN \
- )
-
-/*
- * The CADMUS registers are connected to CS3 on CDS.
- * The new memory map places CADMUS at 0xf8000000.
- *
- * For BR3, need:
- * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
- * port-size = 8-bits = BR[19:20] = 01
- * no parity checking = BR[21:22] = 00
- * GPMC for MSEL = BR[24:26] = 000
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
- *
- * For OR3, need:
- * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
- * disable buffer ctrl OR[19] = 0
- * CSNT OR[20] = 1
- * ACS OR[21:22] = 11
- * XACS OR[23] = 1
- * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
- * SETA OR[28] = 0
- * TRLX OR[29] = 1
- * EHTR OR[30] = 1
- * EAD extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
- */
-
-#define CONFIG_FSL_CADMUS
-
-#define CADMUS_BASE_ADDR 0xf8000000
-#define CONFIG_SYS_BR3_PRELIM 0xf8000801
-#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_CCID
-#define CONFIG_SYS_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
-#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000
-#define CONFIG_SYS_PCI2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000
-#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
-
-#ifdef CONFIG_LEGACY
-#define BRIDGE_ID 17
-#define VIA_ID 2
-#else
-#define BRIDGE_ID 28
-#define VIA_ID 4
-#endif
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_MPC85XX_PCI2
-
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_IPADDR 192.168.1.253
-
-#define CONFIG_HOSTNAME "unknown"
-#define CONFIG_ROOTPATH "/nfsroot"
-#define CONFIG_BOOTFILE "your.uImage"
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS1\0" \
- "ramdiskaddr=600000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=your.fdt.dtb\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff