CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
commit
71ba2cb0d678 ("board: stm32mp1: correct CONFIG_IS_ENABLED usage for LED")
commit
a5ada25e4213 ("rockchip: clk: fix wrong CONFIG_IS_ENABLED handling")
commit
5daf6e56d36c ("common: console: Fix duplicated CONFIG in silent env callback")
commit
48bfc31b6484 ("MIPS: bootm: Fix broken boot_env_legacy codepath")
Fix all files found by `git grep "CONFIG_IS_ENABLED(CONFIG"` by running
':%s/CONFIG_IS_ENABLED(CONFIG_\(\w+\))/CONFIG_IS_ENABLED(\1)/g' in vim.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
static int rk3399_pmuclk_bind(struct udevice *dev)
{
-#if CONFIG_IS_ENABLED(CONFIG_RESET_ROCKCHIP)
+#if CONFIG_IS_ENABLED(RESET_ROCKCHIP)
int ret;
ret = offsetof(struct rk3399_pmucru, pmucru_softrst_con[0]);
fspi_writel(f, FSPI_LCKER_LOCK, f->iobase + FSPI_LCKCR);
}
-#if CONFIG_IS_ENABLED(CONFIG_CLK)
+#if CONFIG_IS_ENABLED(CLK)
static int nxp_fspi_clk_prep_enable(struct nxp_fspi *f)
{
int ret;
int ret, i;
u32 reg;
-#if CONFIG_IS_ENABLED(CONFIG_CLK)
+#if CONFIG_IS_ENABLED(CLK)
/* disable and unprepare clock to avoid glitch pass to controller */
nxp_fspi_clk_disable_unprep(f);
static int nxp_fspi_set_speed(struct udevice *bus, uint speed)
{
-#if CONFIG_IS_ENABLED(CONFIG_CLK)
+#if CONFIG_IS_ENABLED(CLK)
struct nxp_fspi *f = dev_get_priv(bus);
int ret;
static int nxp_fspi_ofdata_to_platdata(struct udevice *bus)
{
struct nxp_fspi *f = dev_get_priv(bus);
-#if CONFIG_IS_ENABLED(CONFIG_CLK)
+#if CONFIG_IS_ENABLED(CLK)
int ret;
#endif
f->ahb_addr = map_physmem(ahb_addr, ahb_size, MAP_NOCACHE);
f->memmap_phy_size = ahb_size;
-#if CONFIG_IS_ENABLED(CONFIG_CLK)
+#if CONFIG_IS_ENABLED(CLK)
ret = clk_get_by_name(bus, "fspi_en", &f->clk_en);
if (ret) {
dev_err(bus, "failed to get fspi_en clock\n");
if (!force && !gd->arch.arbiter_event_address)
return 0;
- if (CONFIG_IS_ENABLED(CONFIG_DISPLAY_AER_FULL)) {
+ if (CONFIG_IS_ENABLED(DISPLAY_AER_FULL)) {
res = snprintf(buf, size,
"Arbiter Event Status:\n"
" %s: 0x%08lX\n"
"Master ID", mstr_id, master[mstr_id],
"Transfer Size", tsize_val, tsize_bytes,
"Transfer Type", ttype, transfer[ttype]);
- } else if (CONFIG_IS_ENABLED(CONFIG_DISPLAY_AER_BRIEF)) {
+ } else if (CONFIG_IS_ENABLED(DISPLAY_AER_BRIEF)) {
res = snprintf(buf, size,
"Arbiter Event Status: AEATR=0x%08lX, AEADR=0x%08lX\n",
gd->arch.arbiter_event_attributes,
* TODO(mario.six@gdsys.cc): Move this into a dedicated
* arbiter driver
*/
- if (CONFIG_IS_ENABLED(CONFIG_DISPLAY_AER_FULL) ||
- CONFIG_IS_ENABLED(CONFIG_DISPLAY_AER_BRIEF)) {
+ if (CONFIG_IS_ENABLED(DISPLAY_AER_FULL) ||
+ CONFIG_IS_ENABLED(DISPLAY_AER_BRIEF)) {
/*
* If there was a bus monitor reset event, we force the arbiter
* event to be printed