#define NUM_OPPS 6
extern void enable_dmm_clocks(void);
+extern void enable_emif_clocks(void);
extern const struct dpll_params dpll_core_opp100;
extern struct dpll_params dpll_mpu_opp100;
unsigned int ddrckectrl;
};
+#ifdef CONFIG_TI816X
+void config_ddr(const struct ddr_data *data, const struct cmd_control *ctrl,
+ const struct emif_regs *regs,
+ const struct dmm_lisa_map_regs *lisa_regs, int nrs);
+#else
void config_ddr(unsigned int pll, const struct ctrl_ioregs *ioregs,
const struct ddr_data *data, const struct cmd_control *ctrl,
const struct emif_regs *regs, int nr);
+#endif
void emif_get_ext_phy_ctrl_const_regs(const u32 **regs, u32 *size);
#endif /* _DDR_DEFS_H */
obj-$(CONFIG_TI816X) += clock_ti816x.o
obj-y += sys_info.o
obj-y += ddr.o
+ifeq ($(CONFIG_TI816X)$(CONFIG_SKIP_LOWLEVEL_INIT),)
obj-y += emif4.o
+endif
+obj-$(CONFIG_TI816X) += ti816x_emif4.o
obj-y += board.o
obj-y += mux.o
DECLARE_GLOBAL_DATA_PTR;
+int dram_init(void)
+{
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+ sdram_init();
+#endif
+
+ /* dram_init must store complete ramsize in gd->ram_size */
+ gd->ram_size = get_ram_size(
+ (void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_MAX_RAM_BANK_SIZE);
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = gd->ram_size;
+
+ return 0;
+}
+
#if !CONFIG_IS_ENABLED(OF_CONTROL)
static const struct ns16550_platdata am33xx_serial[] = {
{ .base = CONFIG_SYS_NS16550_COM1, .reg_shift = 2,
#define MAIN_MDIV7 0x4
/* DDR PLL */
-#if defined(CONFIG_TI816X_DDR_PLL_400) /* 400 MHz */
-#define DDR_N 59
-#define DDR_P 0x1
-#define DDR_MDIV1 0x4
-#define DDR_INTFREQ2 0x8
-#define DDR_FRACFREQ2 0xD99999
-#define DDR_MDIV2 0x1E
-#define DDR_INTFREQ3 0x8
-#define DDR_FRACFREQ3 0x0
-#define DDR_MDIV3 0x4
-#define DDR_INTFREQ4 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ4 0x0
-#define DDR_MDIV4 0x4
-#define DDR_INTFREQ5 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ5 0x0
-#define DDR_MDIV5 0x4
-#elif defined(CONFIG_TI816X_DDR_PLL_531) /* 531 MHz */
-#define DDR_N 59
-#define DDR_P 0x1
-#define DDR_MDIV1 0x3
-#define DDR_INTFREQ2 0x8
-#define DDR_FRACFREQ2 0xD99999
-#define DDR_MDIV2 0x1E
-#define DDR_INTFREQ3 0x8
-#define DDR_FRACFREQ3 0x0
-#define DDR_MDIV3 0x4
-#define DDR_INTFREQ4 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ4 0x0
-#define DDR_MDIV4 0x4
-#define DDR_INTFREQ5 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ5 0x0
-#define DDR_MDIV5 0x4
-#elif defined(CONFIG_TI816X_DDR_PLL_675) /* 675 MHz */
-#define DDR_N 50
-#define DDR_P 0x1
-#define DDR_MDIV1 0x2
-#define DDR_INTFREQ2 0x9
-#define DDR_FRACFREQ2 0x0
-#define DDR_MDIV2 0x19
-#define DDR_INTFREQ3 0x13
-#define DDR_FRACFREQ3 0x800000
-#define DDR_MDIV3 0x2
-#define DDR_INTFREQ4 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ4 0x0
-#define DDR_MDIV4 0x4
-#define DDR_INTFREQ5 0xE /* Expansion DDR clk */
-#define DDR_FRACFREQ5 0x0
-#define DDR_MDIV5 0x4
-#elif defined(CONFIG_TI816X_DDR_PLL_796) /* 796 MHz */
#define DDR_N 59
#define DDR_P 0x1
#define DDR_MDIV1 0x2
#define DDR_INTFREQ5 0xE /* Expansion DDR clk */
#define DDR_FRACFREQ5 0x0
#define DDR_MDIV5 0x4
-#endif
#define CONTROL_STATUS (CTRL_BASE + 0x40)
#define DDR_RCD (CTRL_BASE + 0x070C)
#define CM_TIMER1_CLKSEL (PRCM_BASE + 0x390)
-#define DMM_PAT_BASE_ADDR (DMM_BASE + 0x420)
#define CM_ALWON_CUST_EFUSE_CLKCTRL (PRCM_BASE + 0x1628)
#define INTCPS_SYSCONFIG 0x48200010
void enable_dmm_clocks(void)
{
+ writel(PRCM_MOD_EN, &cmdef->dmmclkctrl);
+ /* Wait for dmm to be fully functional, including OCP */
+ while (((readl(&cmdef->dmmclkctrl) >> 17) & 0x3) != 0)
+ ;
+}
+
+void enable_emif_clocks(void)
+{
+ writel(PRCM_MOD_EN, &cmdef->fwclkctrl);
writel(PRCM_MOD_EN, &cmdef->l3fastclkstctrl);
writel(PRCM_MOD_EN, &cmdef->emif0clkctrl);
writel(PRCM_MOD_EN, &cmdef->emif1clkctrl);
/* Wait for emif1 to be fully functional, including OCP */
while (((readl(&cmdef->emif1clkctrl) >> 17) & 0x3) != 0)
;
-
- writel(PRCM_MOD_EN, &cmdef->dmmclkctrl);
- /* Wait for dmm to be fully functional, including OCP */
- while (((readl(&cmdef->dmmclkctrl) >> 17) & 0x3) != 0)
- ;
-
- /* Enable Tiled Access */
- writel(0x80000000, DMM_PAT_BASE_ADDR);
}
/* assume delay is aprox at least 1us */
*/
void config_sdram(const struct emif_regs *regs, int nr)
{
+#ifdef CONFIG_TI816X
+ writel(regs->sdram_config, &emif_reg[nr]->emif_sdram_config);
+ writel(regs->emif_ddr_phy_ctlr_1, &emif_reg[nr]->emif_ddr_phy_ctrl_1);
+ writel(regs->emif_ddr_phy_ctlr_1, &emif_reg[nr]->emif_ddr_phy_ctrl_1_shdw);
+ writel(0x0000613B, &emif_reg[nr]->emif_sdram_ref_ctrl); /* initially a large refresh period */
+ writel(0x1000613B, &emif_reg[nr]->emif_sdram_ref_ctrl); /* trigger initialization */
+ writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl);
+#else
if (regs->zq_config) {
writel(regs->zq_config, &emif_reg[nr]->emif_zq_config);
writel(regs->sdram_config, &cstat->secure_emif_sdram_config);
/* Write REG_COS_COUNT_1, REG_COS_COUNT_2, and REG_PR_OLD_COUNT. */
if (regs->ocp_config)
writel(regs->ocp_config, &emif_reg[nr]->emif_l3_config);
+#endif
}
/**
#include <asm/io.h>
#include <asm/emif.h>
-DECLARE_GLOBAL_DATA_PTR;
-
-int dram_init(void)
-{
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- sdram_init();
-#endif
-
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size(
- (void *)CONFIG_SYS_SDRAM_BASE,
- CONFIG_MAX_RAM_BANK_SIZE);
- return 0;
-}
-
-int dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- gd->bd->bi_dram[0].size = gd->ram_size;
-
- return 0;
-}
-
-
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-#ifdef CONFIG_TI81XX
-static struct dmm_lisa_map_regs *hw_lisa_map_regs =
- (struct dmm_lisa_map_regs *)DMM_BASE;
-#endif
-#ifndef CONFIG_TI816X
static struct vtp_reg *vtpreg[2] = {
(struct vtp_reg *)VTP0_CTRL_ADDR,
(struct vtp_reg *)VTP1_CTRL_ADDR};
-#endif
#ifdef CONFIG_AM33XX
static struct ddr_ctrl *ddrctrl = (struct ddr_ctrl *)DDR_CTRL_ADDR;
#endif
(struct cm_device_inst *)CM_DEVICE_INST;
#endif
-#ifdef CONFIG_TI81XX
+#ifdef CONFIG_TI814X
void config_dmm(const struct dmm_lisa_map_regs *regs)
{
+ struct dmm_lisa_map_regs *hw_lisa_map_regs =
+ (struct dmm_lisa_map_regs *)DMM_BASE;
+
enable_dmm_clocks();
writel(0, &hw_lisa_map_regs->dmm_lisa_map_3);
}
#endif
-#ifndef CONFIG_TI816X
static void config_vtp(int nr)
{
writel(readl(&vtpreg[nr]->vtp0ctrlreg) | VTP_CTRL_ENABLE,
VTP_CTRL_READY)
;
}
-#endif
void __weak ddr_pll_config(unsigned int ddrpll_m)
{
const struct emif_regs *regs, int nr)
{
ddr_pll_config(pll);
-#ifndef CONFIG_TI816X
config_vtp(nr);
-#endif
config_cmd_ctrl(ctrl, nr);
config_ddr_data(data, nr);
else
config_sdram(regs, nr);
}
-#endif
--- /dev/null
+/*
+ * ti816x_emif4.c
+ *
+ * TI816x emif4 configuration file
+ *
+ * Copyright (C) 2017, Konsulko Group
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+
+/*********************************************************************
+ * Init DDR3 on TI816X EVM
+ *********************************************************************/
+static void ddr_init_settings(const struct cmd_control *ctrl, int emif)
+{
+ /*
+ * setup use_rank_delays to 1. This is only necessary when
+ * multiple ranks are in use. Though the EVM does not have
+ * multiple ranks, this is a good value to set.
+ */
+ writel(1, DDRPHY_CONFIG_BASE + 0x134); // DATA0_REG_PHY_USE_RANK0_DELAYS
+ writel(1, DDRPHY_CONFIG_BASE + 0x1d8); // DATA1_REG_PHY_USE_RANK0_DELAYS
+ writel(1, DDRPHY_CONFIG_BASE + 0x27c); // DATA2_REG_PHY_USE_RANK0_DELAYS
+ writel(1, DDRPHY_CONFIG_BASE + 0x320); // DATA3_REG_PHY_USE_RANK0_DELAYS
+
+ config_cmd_ctrl(ctrl, emif);
+
+ /* for ddr3 this needs to be set to 1 */
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x0F8); /* init mode */
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x104);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x19C);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x1A8);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x240);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x24C);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x2E4);
+ writel(0x1, DDRPHY_CONFIG_BASE + 0x2F0);
+
+ /*
+ * This represents the initial value for the leveling process. The
+ * value is a ratio - so 0x100 represents one cycle. The real delay
+ * is determined through the leveling process.
+ *
+ * During the leveling process, 0x20 is subtracted from the value, so
+ * we have added that to the value we want to set. We also set the
+ * values such that byte3 completes leveling after byte2 and byte1
+ * after byte0.
+ */
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x0F0); /* data0 writelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x0F4); /* */
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x194); /* data1 writelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x198); /* */
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x238); /* data2 writelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x23c); /* */
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x2dc); /* data3 writelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x2e0); /* */
+
+
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x0FC); /* data0 gatelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x100);
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x1A0); /* data1 gatelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x1A4);
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x244); /* data2 gatelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x248);
+ writel((0x20 << 10) | 0x20, DDRPHY_CONFIG_BASE + 0x2E8); /* data3 gatelvl init ratio */
+ writel(0x0, DDRPHY_CONFIG_BASE + 0x2EC);
+
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x00C); /* cmd0 io config - output impedance of pad */
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x010); /* cmd0 io clk config - output impedance of pad */
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x040); /* cmd1 io config - output impedance of pad */
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x044); /* cmd1 io clk config - output impedance of pad */
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x074); /* cmd2 io config - output impedance of pad */
+ writel(0x5, DDRPHY_CONFIG_BASE + 0x078); /* cmd2 io clk config - output impedance of pad */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x0A8); /* data0 io config - output impedance of pad */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x0AC); /* data0 io clk config - output impedance of pad */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x14C); /* data1 io config - output impedance of pa */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x150); /* data1 io clk config - output impedance of pad */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x1F0); /* data2 io config - output impedance of pa */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x1F4); /* data2 io clk config - output impedance of pad */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x294); /* data3 io config - output impedance of pa */
+ writel(0x4, DDRPHY_CONFIG_BASE + 0x298); /* data3 io clk config - output impedance of pad */
+}
+
+static void ddr3_sw_levelling(const struct ddr_data *data, int emif)
+{
+ /* Set the correct value to DDR_VTP_CTRL_0 */
+ writel(0x6, (DDRPHY_CONFIG_BASE + 0x358));
+
+ writel(data->datafwsratio0, (DDRPHY_CONFIG_BASE + 0x108));
+ writel(data->datafwsratio0, (DDRPHY_CONFIG_BASE + 0x1AC));
+ writel(data->datafwsratio0, (DDRPHY_CONFIG_BASE + 0x250));
+ writel(data->datafwsratio0, (DDRPHY_CONFIG_BASE + 0x2F4));
+
+ writel(data->datawdsratio0, (DDRPHY_CONFIG_BASE + 0x0DC));
+ writel(data->datawdsratio0, (DDRPHY_CONFIG_BASE + 0x180));
+ writel(data->datawdsratio0, (DDRPHY_CONFIG_BASE + 0x224));
+ writel(data->datawdsratio0, (DDRPHY_CONFIG_BASE + 0x2C8));
+
+ writel(data->datawrsratio0, (DDRPHY_CONFIG_BASE + 0x120));
+ writel(data->datawrsratio0, (DDRPHY_CONFIG_BASE + 0x1C4));
+ writel(data->datawrsratio0, (DDRPHY_CONFIG_BASE + 0x268));
+ writel(data->datawrsratio0, (DDRPHY_CONFIG_BASE + 0x30C));
+
+ writel(data->datardsratio0, (DDRPHY_CONFIG_BASE + 0x0C8));
+ writel(data->datardsratio0, (DDRPHY_CONFIG_BASE + 0x16C));
+ writel(data->datardsratio0, (DDRPHY_CONFIG_BASE + 0x210));
+ writel(data->datardsratio0, (DDRPHY_CONFIG_BASE + 0x2B4));
+}
+
+static struct dmm_lisa_map_regs *hw_lisa_map_regs =
+ (struct dmm_lisa_map_regs *)DMM_BASE;
+
+#define DMM_PAT_BASE_ADDR (DMM_BASE + 0x420)
+void config_dmm(const struct dmm_lisa_map_regs *regs)
+{
+ writel(0, &hw_lisa_map_regs->dmm_lisa_map_3);
+ writel(0, &hw_lisa_map_regs->dmm_lisa_map_2);
+ writel(0, &hw_lisa_map_regs->dmm_lisa_map_1);
+ writel(0, &hw_lisa_map_regs->dmm_lisa_map_0);
+
+ writel(regs->dmm_lisa_map_3, &hw_lisa_map_regs->dmm_lisa_map_3);
+ writel(regs->dmm_lisa_map_2, &hw_lisa_map_regs->dmm_lisa_map_2);
+ writel(regs->dmm_lisa_map_1, &hw_lisa_map_regs->dmm_lisa_map_1);
+ writel(regs->dmm_lisa_map_0, &hw_lisa_map_regs->dmm_lisa_map_0);
+
+ /* Enable Tiled Access */
+ writel(0x80000000, DMM_PAT_BASE_ADDR);
+}
+
+void config_ddr(const struct ddr_data *data, const struct cmd_control *ctrl,
+ const struct emif_regs *regs,
+ const struct dmm_lisa_map_regs *lisa_regs, int nrs)
+{
+ int i;
+
+ enable_emif_clocks();
+
+ for (i = 0; i < nrs; i++)
+ ddr_init_settings(ctrl, i);
+
+ enable_dmm_clocks();
+
+ /* Program the DMM to for non-interleaved configuration */
+ config_dmm(lisa_regs);
+
+ /* Program EMIF CFG Registers */
+ for (i = 0; i < nrs; i++) {
+ set_sdram_timings(regs, i);
+ config_sdram(regs, i);
+ }
+
+ udelay(1000);
+ for (i = 0; i < nrs; i++)
+ ddr3_sw_levelling(data, i);
+
+ udelay(50000); /* Some delay needed */
+}
{ -1 },
};
-const struct dmm_lisa_map_regs evm_lisa_map_regs = {
- .dmm_lisa_map_0 = 0x00000000,
- .dmm_lisa_map_1 = 0x00000000,
- .dmm_lisa_map_2 = 0x80640300,
- .dmm_lisa_map_3 = 0xC0640320,
-};
-
-/*
- * DDR2 related definitions
- */
-#ifdef CONFIG_TI816X_EVM_DDR2
-static struct ddr_data ddr2_data = {
- .datardsratio0 = ((0x40<<10) | (0x40<<0)),
- .datawdsratio0 = ((0x4A<<10) | (0x4A<<0)),
- .datawiratio0 = ((0x0<<10) | (0x0<<0)),
- .datagiratio0 = ((0x0<<10) | (0x0<<0)),
- .datafwsratio0 = ((0x13A<<10) | (0x13A<<0)),
- .datawrsratio0 = ((0x8A<<10) | (0x8A<<0)),
-};
-
-static struct cmd_control ddr2_ctrl = {
- .cmd0csratio = 0x80,
- .cmd0iclkout = 0x00,
-
- .cmd1csratio = 0x80,
- .cmd1iclkout = 0x00,
-
- .cmd2csratio = 0x80,
- .cmd2iclkout = 0x00,
-
-};
-
-static struct emif_regs ddr2_emif0_regs = {
- .sdram_config = 0x43801A3A,
- .ref_ctrl = 0x10000C30,
- .sdram_tim1 = 0x0AAB15E2,
- .sdram_tim2 = 0x423631D2,
- .sdram_tim3 = 0x0080032F,
- .emif_ddr_phy_ctlr_1 = 0x0, /* depend on cpu rev, set later */
-};
+void set_uart_mux_conf(void) {}
-static struct emif_regs ddr2_emif1_regs = {
- .sdram_config = 0x43801A3A,
- .ref_ctrl = 0x10000C30,
- .sdram_tim1 = 0x0AAB15E2,
- .sdram_tim2 = 0x423631D2,
- .sdram_tim3 = 0x0080032F,
- .emif_ddr_phy_ctlr_1 = 0x0, /* depend on cpu rev, set later */
-};
-#endif
+void set_mux_conf_regs(void)
+{
+ configure_module_pin_mux(mmc_pin_mux);
+}
/*
- * DDR3 related definitions
+ * EMIF Paramters. Refer the EMIF register documentation and the
+ * memory datasheet for details. This is for 796 MHz.
*/
-
-#if defined(CONFIG_TI816X_DDR_PLL_400)
-#define RD_DQS 0x03B
-#define WR_DQS 0x0A6
-#define RD_DQS_GATE 0x12A
-#define EMIF_SDCFG 0x62A41032
-#define EMIF_SDREF 0x10000C30
-#define EMIF_TIM1 0x0CCCE524
-#define EMIF_TIM2 0x30308023
-#define EMIF_TIM3 0x009F82CF
-#define EMIF_PHYCFG 0x0000010B
-#elif defined(CONFIG_TI816X_DDR_PLL_531)
-#define RD_DQS 0x039
-#define WR_DQS 0x0B4
-#define RD_DQS_GATE 0x13D
-#define EMIF_SDCFG 0x62A51832
-#define EMIF_SDREF 0x1000102E
-#define EMIF_TIM1 0x0EF136AC
-#define EMIF_TIM2 0x30408063
-#define EMIF_TIM3 0x009F83AF
-#define EMIF_PHYCFG 0x0000010C
-#elif defined(CONFIG_TI816X_DDR_PLL_675)
-#define RD_DQS 0x039
-#define WR_DQS 0x091
-#define RD_DQS_GATE 0x196
-#define EMIF_SDCFG 0x62A63032
-#define EMIF_SDREF 0x10001491
-#define EMIF_TIM1 0x13358875
-#define EMIF_TIM2 0x5051806C
-#define EMIF_TIM3 0x009F84AF
-#define EMIF_PHYCFG 0x0000010F
-#elif defined(CONFIG_TI816X_DDR_PLL_796)
-#define RD_DQS 0x035
-#define WR_DQS 0x093
-#define RD_DQS_GATE 0x1B3
-#define EMIF_SDCFG 0x62A73832
-#define EMIF_SDREF 0x10001841
-#define EMIF_TIM1 0x1779C9FE
-#define EMIF_TIM2 0x50608074
-#define EMIF_TIM3 0x009F857F
-#define EMIF_PHYCFG 0x00000110
-#endif
-
-static struct ddr_data ddr3_data = {
- .datardsratio0 = ((RD_DQS<<10) | (RD_DQS<<0)),
- .datawdsratio0 = ((WR_DQS<<10) | (WR_DQS<<0)),
- .datawiratio0 = ((0x20<<10) | 0x20<<0),
- .datagiratio0 = ((0x20<<10) | 0x20<<0),
- .datafwsratio0 = ((RD_DQS_GATE<<10) | (RD_DQS_GATE<<0)),
- .datawrsratio0 = (((WR_DQS+0x40)<<10) | ((WR_DQS+0x40)<<0)),
+#define EMIF_TIM1 0x1779C9FE
+#define EMIF_TIM2 0x50608074
+#define EMIF_TIM3 0x009F857F
+#define EMIF_SDREF 0x10001841
+#define EMIF_SDCFG 0x62A73832
+#define EMIF_PHYCFG 0x00000110
+static const struct emif_regs ddr3_emif_regs = {
+ .sdram_config = EMIF_SDCFG,
+ .ref_ctrl = EMIF_SDREF,
+ .sdram_tim1 = EMIF_TIM1,
+ .sdram_tim2 = EMIF_TIM2,
+ .sdram_tim3 = EMIF_TIM3,
+ .emif_ddr_phy_ctlr_1 = EMIF_PHYCFG,
};
static const struct cmd_control ddr3_ctrl = {
.cmd0csratio = 0x100,
.cmd0iclkout = 0x001,
-
.cmd1csratio = 0x100,
.cmd1iclkout = 0x001,
-
.cmd2csratio = 0x100,
.cmd2iclkout = 0x001,
};
-static const struct emif_regs ddr3_emif0_regs = {
- .sdram_config = EMIF_SDCFG,
- .ref_ctrl = EMIF_SDREF,
- .sdram_tim1 = EMIF_TIM1,
- .sdram_tim2 = EMIF_TIM2,
- .sdram_tim3 = EMIF_TIM3,
- .emif_ddr_phy_ctlr_1 = EMIF_PHYCFG,
+/* These values are obtained from the CCS app */
+#define RD_DQS_GATE (0x1B3)
+#define RD_DQS (0x35)
+#define WR_DQS (0x93)
+static struct ddr_data ddr3_data = {
+ .datardsratio0 = ((RD_DQS<<10) | (RD_DQS<<0)),
+ .datawdsratio0 = ((WR_DQS<<10) | (WR_DQS<<0)),
+ .datawiratio0 = ((0x20<<10) | 0x20<<0),
+ .datagiratio0 = ((0x20<<10) | 0x20<<0),
+ .datafwsratio0 = ((RD_DQS_GATE<<10) | (RD_DQS_GATE<<0)),
+ .datawrsratio0 = (((WR_DQS+0x40)<<10) | ((WR_DQS+0x40)<<0)),
};
-static const struct emif_regs ddr3_emif1_regs = {
- .sdram_config = EMIF_SDCFG,
- .ref_ctrl = EMIF_SDREF,
- .sdram_tim1 = EMIF_TIM1,
- .sdram_tim2 = EMIF_TIM2,
- .sdram_tim3 = EMIF_TIM3,
- .emif_ddr_phy_ctlr_1 = EMIF_PHYCFG,
+static const struct dmm_lisa_map_regs evm_lisa_map_regs = {
+ .dmm_lisa_map_0 = 0x00000000,
+ .dmm_lisa_map_1 = 0x00000000,
+ .dmm_lisa_map_2 = 0x80640300,
+ .dmm_lisa_map_3 = 0xC0640320,
};
-void set_uart_mux_conf(void) {}
-
-void set_mux_conf_regs(void)
-{
- configure_module_pin_mux(mmc_pin_mux);
-}
-
void sdram_init(void)
{
- config_dmm(&evm_lisa_map_regs);
-
-#ifdef CONFIG_TI816X_EVM_DDR2
- if (CONFIG_TI816X_USE_EMIF0) {
- ddr2_emif0_regs.emif_ddr_phy_ctlr_1 =
- (get_cpu_rev() == 0x1 ? 0x0000010B : 0x0000030B);
- config_ddr(0, NULL, &ddr2_data, &ddr2_ctrl, &ddr2_emif0_regs,
- 0);
- }
-
- if (CONFIG_TI816X_USE_EMIF1) {
- ddr2_emif1_regs.emif_ddr_phy_ctlr_1 =
- (get_cpu_rev() == 0x1 ? 0x0000010B : 0x0000030B);
- config_ddr(1, NULL, &ddr2_data, &ddr2_ctrl, &ddr2_emif1_regs,
- 1);
- }
-#endif
-
-#ifdef CONFIG_TI816X_EVM_DDR3
- if (CONFIG_TI816X_USE_EMIF0)
- config_ddr(0, NULL, &ddr3_data, &ddr3_ctrl, &ddr3_emif0_regs,
- 0);
-
- if (CONFIG_TI816X_USE_EMIF1)
- config_ddr(1, NULL, &ddr3_data, &ddr3_ctrl, &ddr3_emif1_regs,
- 1);
-#endif
+ /*
+ * Pass in our DDR3 config information and that we have 2 EMIFs to
+ * configure.
+ */
+ config_ddr(&ddr3_data, &ddr3_ctrl, &ddr3_emif_regs,
+ &evm_lisa_map_regs, 2);
}
#endif /* CONFIG_SPL_BUILD */
#define CONFIG_CMD_ASKENV
-/*
- * Only one of the following two options (DDR3/DDR2) should be enabled
- * CONFIG_TI816X_EVM_DDR2
- * CONFIG_TI816X_EVM_DDR3
- */
-#define CONFIG_TI816X_EVM_DDR3
-
-/*
- * Supported values: 400, 531, 675 or 796 MHz
- */
-#define CONFIG_TI816X_DDR_PLL_796
-
-#define CONFIG_TI816X_USE_EMIF0 1
-#define CONFIG_TI816X_USE_EMIF1 1
-
#define CONFIG_NR_DRAM_BANKS 2 /* we have 2 banks of DRAM */
#define PHYS_DRAM_1 0x80000000 /* DRAM Bank #1 */
#define PHYS_DRAM_1_SIZE 0x40000000 /* 1 GB */
CONFIG_THUNDERX
CONFIG_TI814X
CONFIG_TI816X
-CONFIG_TI816X_DDR_PLL_796
-CONFIG_TI816X_EVM_DDR2
-CONFIG_TI816X_EVM_DDR3
-CONFIG_TI816X_USE_EMIF0
-CONFIG_TI816X_USE_EMIF1
CONFIG_TI81XX
CONFIG_TIMESTAMP
CONFIG_TIZEN
projects / u-boot.git / commitdiff