bool "Support suvd3"
select VENDOR_KM
-config TARGET_KMVECT1
- bool "Support kmvect1"
- select VENDOR_KM
-
config TARGET_KMTEGR1
bool "Support kmtegr1"
select VENDOR_KM
/* if an offset is defined, add it */
process_mac(valbuf, page2, CONFIG_PIGGY_MAC_ADRESS_OFFSET, true);
env_set((char *)"ethaddr", (char *)valbuf);
-#ifdef CONFIG_KMVECT1
-/* KMVECT1 has two ethernet interfaces */
- process_mac(valbuf, page2, 1, true);
- env_set((char *)"eth1addr", (char *)valbuf);
-#endif
#else
/* KMTEGR1 has a special setup. eth0 has no connection to the outside and
* gets an locally administred MAC address, eth1 is the debug interface and
endif
-if TARGET_KMVECT1
-
-config SYS_BOARD
- default "km83xx"
-
-config SYS_VENDOR
- default "keymile"
-
-config SYS_CONFIG_NAME
- default "kmvect1"
-
-config BOARD_SPECIFIC_OPTIONS # dummy
- def_bool y
- select ARCH_MPC8309
- imply CMD_CRAMFS
- imply FS_CRAMFS
-
-endif
-
if TARGET_KMTEGR1
config SYS_BOARD
F: configs/kmtepr2_defconfig
F: include/configs/suvd3.h
F: configs/kmtegr1_defconfig
-F: configs/kmvect1_defconfig
F: configs/suvd3_defconfig
F: configs/tuge1_defconfig
F: configs/tuxx1_defconfig
return in_8(&base->bprth) & PIGGY_PRESENT;
}
-#if defined(CONFIG_KMVECT1)
-int ethernet_present(void)
-{
- /* ethernet port connected to simple switch without piggy */
- return 1;
-}
-#else
int ethernet_present(void)
{
return piggy_present();
}
-#endif
-
int board_early_init_r(void)
{
return 0;
}
-#if defined(CONFIG_KMVECT1)
-#include <mv88e6352.h>
-/* Marvell MV88E6122 switch configuration */
-static struct mv88e_sw_reg extsw_conf[] = {
- /* port 1, FRONT_MDI, autoneg */
- { PORT(1), PORT_PHY, NO_SPEED_FOR },
- { PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- { PHY(1), PHY_1000_CTRL, NO_ADV },
- { PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN },
- { PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
- FULL_DUPLEX },
- /* port 2, unused */
- { PORT(2), PORT_CTRL, PORT_DIS },
- { PHY(2), PHY_CTRL, PHY_PWR_DOWN },
- { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
- /* port 3, BP_MII (CPU), PHY mode, 100BASE */
- { PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */
- { PORT(4), PORT_STATUS, NO_PHY_DETECT },
- { PORT(4), PORT_PHY, SPEED_1000_FOR },
- { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */
- { PORT(5), PORT_STATUS, NO_PHY_DETECT },
- { PORT(5), PORT_PHY, SPEED_1000_FOR },
- { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
- /*
- * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
- * acc . MV-S300889-00D.pdf , clause 4.5
- */
- { PORT(5), 0x1A, 0xADB1 },
- /* port 6, unused, this port has no phy */
- { PORT(6), PORT_CTRL, PORT_DIS },
- /*
- * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
- * acc . MV-S300889-00D.pdf , clause 4.5
- */
- { PORT(5), 0x1A, 0xADB1 },
-};
-#endif
-
int last_stage_init(void)
{
-#if defined(CONFIG_KMVECT1)
- struct km_bec_fpga __iomem *base =
- (struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE;
- u8 tmp_reg;
-
- /* Release mv88e6122 from reset */
- tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */
- out_8(&base->res1[0], tmp_reg); /* GP28 as output */
- tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */
- out_8(&base->gprt3, tmp_reg);
-
- /* configure MV88E6122 switch */
- char *name = "UEC2";
-
- if (miiphy_set_current_dev(name))
- return 0;
-
- mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
- ARRAY_SIZE(extsw_conf));
-
- mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
-
- if (piggy_present()) {
- env_set("ethact", "UEC2");
- env_set("netdev", "eth1");
- puts("using PIGGY for network boot\n");
- } else {
- env_set("netdev", "eth0");
- puts("using frontport for network boot\n");
- }
-#endif
-
#if defined(CONFIG_TARGET_KMCOGE5NE)
struct bfticu_iomap *base =
(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xF0000000
-CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_KMVECT1=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_QUICC_MULT_FACTOR_3=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_INHIBITED=y
-CONFIG_BAT0_ICACHE_GUARDED=y
-CONFIG_BAT0_DCACHE_INHIBITED=y
-CONFIG_BAT0_DCACHE_GUARDED=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_4_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="KMBEC_FPGA"
-CONFIG_BAT2_BASE=0xE8000000
-CONFIG_BAT2_LENGTH_128_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="FLASH"
-CONFIG_BAT3_BASE=0xF0000000
-CONFIG_BAT3_LENGTH_256_MBYTES=y
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT3_DCACHE_INHIBITED=y
-CONFIG_BAT3_DCACHE_GUARDED=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="STACK_IN_DCACHE"
-CONFIG_BAT4_BASE=0xE6000000
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="APP1"
-CONFIG_BAT5_BASE=0xA0000000
-CONFIG_BAT5_LENGTH_256_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="APP2"
-CONFIG_BAT6_BASE=0xB0000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_DCACHE_INHIBITED=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xF0000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_256_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xE8000000
-CONFIG_LBLAW1_NAME="KMBEC_FPGA"
-CONFIG_LBLAW1_LENGTH_128_MBYTES=y
-CONFIG_LBLAW2=y
-CONFIG_LBLAW2_BASE=0xA0000000
-CONFIG_LBLAW2_NAME="APP1"
-CONFIG_LBLAW2_LENGTH_256_MBYTES=y
-CONFIG_LBLAW3=y
-CONFIG_LBLAW3_BASE=0xB0000000
-CONFIG_LBLAW3_NAME="APP2"
-CONFIG_LBLAW3_LENGTH_256_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xF0000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_256_MBYTES=y
-CONFIG_OR0_SCY_5=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="KMBEC_FPGA"
-CONFIG_BR1_OR1_BASE=0xE8000000
-CONFIG_OR1_AM_128_MBYTES=y
-CONFIG_OR1_SCY_2=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_OR1_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR1_TRLX_RELAXED=y
-CONFIG_OR1_EAD_EXTRA=y
-CONFIG_ELBC_BR2_OR2=y
-CONFIG_BR2_OR2_NAME="APP1"
-CONFIG_BR2_OR2_BASE=0xA0000000
-CONFIG_BR2_PORTSIZE_16BIT=y
-CONFIG_BR2_MACHINE_UPMA=y
-CONFIG_OR2_AM_256_MBYTES=y
-CONFIG_ELBC_BR3_OR3=y
-CONFIG_BR3_OR3_NAME="APP2"
-CONFIG_BR3_OR3_BASE=0xB0000000
-CONFIG_BR3_PORTSIZE_16BIT=y
-CONFIG_OR3_AM_256_MBYTES=y
-CONFIG_OR3_SCY_3=y
-CONFIG_OR3_CSNT_EARLIER=y
-CONFIG_OR3_ACS_QUARTER_CYCLE_EARLIER=y
-CONFIG_OR3_TRLX_RELAXED=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_ACR_APARK_MASTER=y
-CONFIG_ACR_PARKM_USB_I2C1_BOOT=y
-CONFIG_LCRR_EADC_1=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="KMVECT1"
-CONFIG_MISC_INIT_R=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=boot"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);"
-CONFIG_CMD_DIAG=y
-CONFIG_CMD_UBI=y
-# CONFIG_CMD_UBIFS is not set
-CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_BOOTCOUNT_BOOTLIMIT=3
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_DEVICE=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MV88E6352_SWITCH=y
-# CONFIG_PCI is not set
-CONFIG_QE=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- * Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * (C) Copyright 2010
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-
-#define CONFIG_HOSTNAME "kmvect1"
-#define CONFIG_KM_BOARD_NAME "kmvect1"
-/* at end of uboot partition, before env */
-#define CONFIG_SYS_QE_FW_ADDR 0xF00B0000
-
-/* include common defines/options for all Keymile boards */
-#include "km/keymile-common.h"
-#include "km/km-powerpc.h"
-#include "km/km-mpc83xx.h"
-#include "km/km-mpc8309.h"
-
-#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
- 0x0000c000 | \
- MxMR_WLFx_2X)
-
-/* ethernet port connected to simple switch 88e6122 (UEC0) */
-#define CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
-
-#define CONFIG_FIXED_PHY 0xFFFFFFFF
-#define CONFIG_SYS_FIXED_PHY_ADDR 0x1E /* unused address */
-#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
- {devnum, speed, duplex}
-#define CONFIG_SYS_FIXED_PHY_PORTS \
- CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL)
-
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-
-#endif /* __CONFIG_H */
CONFIG_KMLION1
CONFIG_KMP204X
CONFIG_KMTEGR1
-CONFIG_KMVECT1
CONFIG_KM_BOARD_EXTRA_ENV
CONFIG_KM_BOARD_NAME
CONFIG_KM_COGE5UN
projects / u-boot.git / commitdiff