Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
#define DCR_DDR4 (4 << 0)
#define DCR_DDR8BANK BIT(3)
+/*
+ * The delay parameters allow to allegedly specify delay times of some
+ * unknown unit for each individual bit trace in each of the four data bytes
+ * the 32-bit wide access consists of. Also three control signals can be
+ * adjusted individually.
+ */
+#define NR_OF_BYTE_LANES (32 / BITS_PER_BYTE)
+/* The eight data lines (DQn) plus DM, DQS, DQS/DM/DQ Output Enable and DQSN */
+#define WR_LINES_PER_BYTE_LANE (BITS_PER_BYTE + 4)
+/*
+ * The eight data lines (DQn) plus DM, DQS, DQS/DM/DQ Output Enable, DQSN,
+ * Termination and Power down
+ */
+#define RD_LINES_PER_BYTE_LANE (BITS_PER_BYTE + 6)
+struct dram_para {
+ u32 clk;
+ enum sunxi_dram_type type;
+ u8 cols;
+ u8 rows;
+ u8 ranks;
+ const u8 dx_read_delays[NR_OF_BYTE_LANES][RD_LINES_PER_BYTE_LANE];
+ const u8 dx_write_delays[NR_OF_BYTE_LANES][WR_LINES_PER_BYTE_LANE];
+};
+
+
static inline int ns_to_t(int nanoseconds)
{
const unsigned int ctrl_freq = CONFIG_DRAM_CLK / 2;
return DIV_ROUND_UP(ctrl_freq * nanoseconds, 1000);
}
+void mctl_set_timing_params(struct dram_para *para);
+
#endif /* _SUNXI_DRAM_SUN50I_H6_H */
This allows both the SPL and the U-Boot proper to be entered in
either mode and switch to AArch64 if needed.
-if SUNXI_DRAM_DW
+if SUNXI_DRAM_DW || DRAM_SUN50I_H6
config SUNXI_DRAM_DDR3
bool
This option is the LPDDR3 timing used by the stock boot0 by
Allwinner.
+config SUNXI_DRAM_H6_LPDDR3
+ bool "LPDDR3 DRAM chips on the H6 DRAM controller"
+ select SUNXI_DRAM_LPDDR3
+ depends on DRAM_SUN50I_H6
+ ---help---
+ This option is the LPDDR3 timing used by the stock boot0 by
+ Allwinner.
+
config SUNXI_DRAM_DDR2_V3S
bool "DDR2 found in V3s chip"
select SUNXI_DRAM_DDR2
obj-$(CONFIG_SUNXI_DRAM_DW) += dram_sunxi_dw.o
obj-$(CONFIG_SUNXI_DRAM_DW) += dram_timings/
obj-$(CONFIG_DRAM_SUN50I_H6) += dram_sun50i_h6.o
+obj-$(CONFIG_DRAM_SUN50I_H6) += dram_timings/
endif
* similar PHY is ZynqMP.
*/
-/*
- * The delay parameters below allow to allegedly specify delay times of some
- * unknown unit for each individual bit trace in each of the four data bytes
- * the 32-bit wide access consists of. Also three control signals can be
- * adjusted individually.
- */
-#define NR_OF_BYTE_LANES (32 / BITS_PER_BYTE)
-/* The eight data lines (DQn) plus DM, DQS, DQS/DM/DQ Output Enable and DQSN */
-#define WR_LINES_PER_BYTE_LANE (BITS_PER_BYTE + 4)
-/*
- * The eight data lines (DQn) plus DM, DQS, DQS/DM/DQ Output Enable, DQSN,
- * Termination and Power down
- */
-#define RD_LINES_PER_BYTE_LANE (BITS_PER_BYTE + 6)
-struct dram_para {
- u32 clk;
- enum sunxi_dram_type type;
- u8 cols;
- u8 rows;
- u8 ranks;
- const u8 dx_read_delays[NR_OF_BYTE_LANES][RD_LINES_PER_BYTE_LANE];
- const u8 dx_write_delays[NR_OF_BYTE_LANES][WR_LINES_PER_BYTE_LANE];
-};
-
static void mctl_sys_init(struct dram_para *para);
static void mctl_com_init(struct dram_para *para);
-static void mctl_set_timing_lpddr3(struct dram_para *para);
static void mctl_channel_init(struct dram_para *para);
static void mctl_core_init(struct dram_para *para)
mctl_com_init(para);
switch (para->type) {
case SUNXI_DRAM_TYPE_LPDDR3:
- mctl_set_timing_lpddr3(para);
+ mctl_set_timing_params(para);
break;
default:
panic("Unsupported DRAM type!");
MBUS_CONF(HDCP2, true, HIGH, 2, 100, 64, 32);
}
-static u32 mr_lpddr3[12] = {
- 0x00000000, 0x00000043, 0x0000001a, 0x00000001,
- 0x00000000, 0x00000000, 0x00000048, 0x00000000,
- 0x00000000, 0x00000000, 0x00000000, 0x00000003,
-};
-
-/* TODO: flexible timing */
-static void mctl_set_timing_lpddr3(struct dram_para *para)
-{
- struct sunxi_mctl_ctl_reg * const mctl_ctl =
- (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
- struct sunxi_mctl_phy_reg * const mctl_phy =
- (struct sunxi_mctl_phy_reg *)SUNXI_DRAM_PHY0_BASE;
- int i;
-
- u8 tccd = 2;
- u8 tfaw = max(ns_to_t(50), 4);
- u8 trrd = max(ns_to_t(10), 2);
- u8 trcd = max(ns_to_t(24), 2);
- u8 trc = ns_to_t(70);
- u8 txp = max(ns_to_t(8), 2);
- u8 twtr = max(ns_to_t(8), 2);
- u8 trtp = max(ns_to_t(8), 2);
- u8 twr = max(ns_to_t(15), 2);
- u8 trp = ns_to_t(18);
- u8 tras = ns_to_t(42);
- u8 twtr_sa = ns_to_t(5);
- u8 tcksrea = ns_to_t(11);
- u16 trefi = ns_to_t(3900) / 32;
- u16 trfc = ns_to_t(210);
- u16 txsr = ns_to_t(220);
-
- if (CONFIG_DRAM_CLK % 400 == 0) {
- /* Round up these parameters */
- twtr_sa++;
- tcksrea++;
- }
-
- u8 tmrw = 5;
- u8 tmrd = 5;
- u8 tmod = 12;
- u8 tcke = 3;
- u8 tcksrx = 5;
- u8 tcksre = 5;
- u8 tckesr = 5;
- u8 trasmax = CONFIG_DRAM_CLK / 60;
- u8 txs = 4;
- u8 txsdll = 4;
- u8 txsabort = 4;
- u8 txsfast = 4;
-
- u8 tcl = 5; /* CL 10 */
- u8 tcwl = 3; /* CWL 6 */
- u8 t_rdata_en = twtr_sa + 8;
-
- u32 tdinit0 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */
- u32 tdinit1 = (100 * CONFIG_DRAM_CLK) / 1000 + 1; /* 100ns */
- u32 tdinit2 = (11 * CONFIG_DRAM_CLK) + 1; /* 11us */
- u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */
-
- u8 twtp = tcwl + 4 + twr + 1;
- /*
- * The code below for twr2rd and trd2wr follows the IP core's
- * document from ZynqMP and i.MX7. The BSP has both number
- * substracted by 2.
- */
- u8 twr2rd = tcwl + 4 + 1 + twtr;
- u8 trd2wr = tcl + 4 + (tcksrea >> 1) - tcwl + 1;
-
- /* set mode registers */
- for (i = 0; i < ARRAY_SIZE(mr_lpddr3); i++)
- writel(mr_lpddr3[i], &mctl_phy->mr[i]);
-
- /* set DRAM timing */
- writel((twtp << 24) | (tfaw << 16) | (trasmax << 8) | tras,
- &mctl_ctl->dramtmg[0]);
- writel((txp << 16) | (trtp << 8) | trc, &mctl_ctl->dramtmg[1]);
- writel((tcwl << 24) | (tcl << 16) | (trd2wr << 8) | twr2rd,
- &mctl_ctl->dramtmg[2]);
- writel((tmrw << 20) | (tmrd << 12) | tmod, &mctl_ctl->dramtmg[3]);
- writel((trcd << 24) | (tccd << 16) | (trrd << 8) | trp,
- &mctl_ctl->dramtmg[4]);
- writel((tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | tcke,
- &mctl_ctl->dramtmg[5]);
- /* Value suggested by ZynqMP manual and used by libdram */
- writel((txp + 2) | 0x02020000, &mctl_ctl->dramtmg[6]);
- writel((txsfast << 24) | (txsabort << 16) | (txsdll << 8) | txs,
- &mctl_ctl->dramtmg[8]);
- writel(txsr, &mctl_ctl->dramtmg[14]);
-
- clrsetbits_le32(&mctl_ctl->init[0], (3 << 30), (1 << 30));
- writel(0, &mctl_ctl->dfimisc);
- clrsetbits_le32(&mctl_ctl->rankctl, 0xff0, 0x660);
-
- /*
- * Set timing registers of the PHY.
- * Note: the PHY is clocked 2x from the DRAM frequency.
- */
- writel((trrd << 25) | (tras << 17) | (trp << 9) | (trtp << 1),
- &mctl_phy->dtpr[0]);
- writel((tfaw << 17) | 0x28000400 | (tmrd << 1), &mctl_phy->dtpr[1]);
- writel(((txs << 6) - 1) | (tcke << 17), &mctl_phy->dtpr[2]);
- writel(((txsdll << 22) - (0x1 << 16)) | twtr_sa | (tcksrea << 8),
- &mctl_phy->dtpr[3]);
- writel((txp << 1) | (trfc << 17) | 0x800, &mctl_phy->dtpr[4]);
- writel((trc << 17) | (trcd << 9) | (twtr << 1), &mctl_phy->dtpr[5]);
- writel(0x0505, &mctl_phy->dtpr[6]);
-
- /* Configure DFI timing */
- writel(tcl | 0x2000200 | (t_rdata_en << 16) | 0x808000,
- &mctl_ctl->dfitmg0);
- writel(0x040201, &mctl_ctl->dfitmg1);
-
- /* Configure PHY timing */
- writel(tdinit0 | (tdinit1 << 20), &mctl_phy->ptr[3]);
- writel(tdinit2 | (tdinit3 << 18), &mctl_phy->ptr[4]);
-
- /* set refresh timing */
- writel((trefi << 16) | trfc, &mctl_ctl->rfshtmg);
-}
-
static void mctl_sys_init(struct dram_para *para)
{
struct sunxi_ccm_reg * const ccm =
(struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
struct dram_para para = {
.clk = CONFIG_DRAM_CLK,
+#ifdef CONFIG_SUNXI_DRAM_H6_LPDDR3
.type = SUNXI_DRAM_TYPE_LPDDR3,
.ranks = 2,
.cols = 11,
.rows = 14,
.dx_read_delays = SUN50I_H6_DX_READ_DELAYS,
.dx_write_delays = SUN50I_H6_DX_WRITE_DELAYS,
+#endif
};
unsigned long size;
obj-$(CONFIG_SUNXI_DRAM_DDR3_1333) += ddr3_1333.o
obj-$(CONFIG_SUNXI_DRAM_LPDDR3_STOCK) += lpddr3_stock.o
obj-$(CONFIG_SUNXI_DRAM_DDR2_V3S) += ddr2_v3s.o
+obj-$(CONFIG_SUNXI_DRAM_H6_LPDDR3) += h6_lpddr3.o
--- /dev/null
+/*
+ * sun50i H6 LPDDR3 timings
+ *
+ * (C) Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/dram.h>
+#include <asm/arch/cpu.h>
+
+static u32 mr_lpddr3[12] = {
+ 0x00000000, 0x00000043, 0x0000001a, 0x00000001,
+ 0x00000000, 0x00000000, 0x00000048, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000003,
+};
+
+/* TODO: flexible timing */
+void mctl_set_timing_params(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ struct sunxi_mctl_phy_reg * const mctl_phy =
+ (struct sunxi_mctl_phy_reg *)SUNXI_DRAM_PHY0_BASE;
+ int i;
+
+ u8 tccd = 2;
+ u8 tfaw = max(ns_to_t(50), 4);
+ u8 trrd = max(ns_to_t(10), 2);
+ u8 trcd = max(ns_to_t(24), 2);
+ u8 trc = ns_to_t(70);
+ u8 txp = max(ns_to_t(8), 2);
+ u8 twtr = max(ns_to_t(8), 2);
+ u8 trtp = max(ns_to_t(8), 2);
+ u8 twr = max(ns_to_t(15), 2);
+ u8 trp = ns_to_t(18);
+ u8 tras = ns_to_t(42);
+ u8 twtr_sa = ns_to_t(5);
+ u8 tcksrea = ns_to_t(11);
+ u16 trefi = ns_to_t(3900) / 32;
+ u16 trfc = ns_to_t(210);
+ u16 txsr = ns_to_t(220);
+
+ if (CONFIG_DRAM_CLK % 400 == 0) {
+ /* Round up these parameters */
+ twtr_sa++;
+ tcksrea++;
+ }
+
+ u8 tmrw = 5;
+ u8 tmrd = 5;
+ u8 tmod = 12;
+ u8 tcke = 3;
+ u8 tcksrx = 5;
+ u8 tcksre = 5;
+ u8 tckesr = 5;
+ u8 trasmax = CONFIG_DRAM_CLK / 60;
+ u8 txs = 4;
+ u8 txsdll = 4;
+ u8 txsabort = 4;
+ u8 txsfast = 4;
+
+ u8 tcl = 5; /* CL 10 */
+ u8 tcwl = 3; /* CWL 6 */
+ u8 t_rdata_en = twtr_sa + 8;
+
+ u32 tdinit0 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */
+ u32 tdinit1 = (100 * CONFIG_DRAM_CLK) / 1000 + 1; /* 100ns */
+ u32 tdinit2 = (11 * CONFIG_DRAM_CLK) + 1; /* 11us */
+ u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */
+
+ u8 twtp = tcwl + 4 + twr + 1;
+ /*
+ * The code below for twr2rd and trd2wr follows the IP core's
+ * document from ZynqMP and i.MX7. The BSP has both number
+ * substracted by 2.
+ */
+ u8 twr2rd = tcwl + 4 + 1 + twtr;
+ u8 trd2wr = tcl + 4 + (tcksrea >> 1) - tcwl + 1;
+
+ /* set mode registers */
+ for (i = 0; i < ARRAY_SIZE(mr_lpddr3); i++)
+ writel(mr_lpddr3[i], &mctl_phy->mr[i]);
+
+ /* set DRAM timing */
+ writel((twtp << 24) | (tfaw << 16) | (trasmax << 8) | tras,
+ &mctl_ctl->dramtmg[0]);
+ writel((txp << 16) | (trtp << 8) | trc, &mctl_ctl->dramtmg[1]);
+ writel((tcwl << 24) | (tcl << 16) | (trd2wr << 8) | twr2rd,
+ &mctl_ctl->dramtmg[2]);
+ writel((tmrw << 20) | (tmrd << 12) | tmod, &mctl_ctl->dramtmg[3]);
+ writel((trcd << 24) | (tccd << 16) | (trrd << 8) | trp,
+ &mctl_ctl->dramtmg[4]);
+ writel((tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | tcke,
+ &mctl_ctl->dramtmg[5]);
+ /* Value suggested by ZynqMP manual and used by libdram */
+ writel((txp + 2) | 0x02020000, &mctl_ctl->dramtmg[6]);
+ writel((txsfast << 24) | (txsabort << 16) | (txsdll << 8) | txs,
+ &mctl_ctl->dramtmg[8]);
+ writel(txsr, &mctl_ctl->dramtmg[14]);
+
+ clrsetbits_le32(&mctl_ctl->init[0], (3 << 30), (1 << 30));
+ writel(0, &mctl_ctl->dfimisc);
+ clrsetbits_le32(&mctl_ctl->rankctl, 0xff0, 0x660);
+
+ /*
+ * Set timing registers of the PHY.
+ * Note: the PHY is clocked 2x from the DRAM frequency.
+ */
+ writel((trrd << 25) | (tras << 17) | (trp << 9) | (trtp << 1),
+ &mctl_phy->dtpr[0]);
+ writel((tfaw << 17) | 0x28000400 | (tmrd << 1), &mctl_phy->dtpr[1]);
+ writel(((txs << 6) - 1) | (tcke << 17), &mctl_phy->dtpr[2]);
+ writel(((txsdll << 22) - (0x1 << 16)) | twtr_sa | (tcksrea << 8),
+ &mctl_phy->dtpr[3]);
+ writel((txp << 1) | (trfc << 17) | 0x800, &mctl_phy->dtpr[4]);
+ writel((trc << 17) | (trcd << 9) | (twtr << 1), &mctl_phy->dtpr[5]);
+ writel(0x0505, &mctl_phy->dtpr[6]);
+
+ /* Configure DFI timing */
+ writel(tcl | 0x2000200 | (t_rdata_en << 16) | 0x808000,
+ &mctl_ctl->dfitmg0);
+ writel(0x040201, &mctl_ctl->dfitmg1);
+
+ /* Configure PHY timing */
+ writel(tdinit0 | (tdinit1 << 20), &mctl_phy->ptr[3]);
+ writel(tdinit2 | (tdinit3 << 18), &mctl_phy->ptr[4]);
+
+ /* set refresh timing */
+ writel((trefi << 16) | trfc, &mctl_ctl->rfshtmg);
+}
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC0_CD_PIN="PF6"
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
# CONFIG_PSCI_RESET is not set
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC0_CD_PIN="PF6"
# CONFIG_PSCI_RESET is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC0_CD_PIN="PF6"
# CONFIG_PSCI_RESET is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC0_CD_PIN="PF6"
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
# CONFIG_PSCI_RESET is not set
projects / u-boot.git / commitdiff