--- /dev/null
+/*
+ * (C) 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Support for the ANX9804 bridge chip, which can take pixel data coming
+ * from a parallel LCD interface and translate it on the flight into a DP
+ * interface for driving eDP TFT displays.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include "anx9804.h"
+
+#define BIT(x) (1 << (x))
+
+/* Registers at i2c address 0x38 */
+
+#define ANX9804_HDCP_CONTROL_0_REG 0x01
+
+#define ANX9804_SYS_CTRL2_REG 0x81
+#define ANX9804_SYS_CTRL2_CHA_STA 0x04
+
+#define ANX9804_SYS_CTRL3_REG 0x82
+#define ANX9804_SYS_CTRL3_VALID_CTRL BIT(0)
+#define ANX9804_SYS_CTRL3_F_VALID BIT(1)
+#define ANX9804_SYS_CTRL3_HPD_CTRL BIT(4)
+#define ANX9804_SYS_CTRL3_F_HPD BIT(5)
+
+#define ANX9804_LINK_BW_SET_REG 0xa0
+#define ANX9804_LANE_COUNT_SET_REG 0xa1
+#define ANX9804_TRAINING_PTN_SET_REG 0xa2
+#define ANX9804_TRAINING_LANE0_SET_REG 0xa3
+#define ANX9804_TRAINING_LANE1_SET_REG 0xa4
+#define ANX9804_TRAINING_LANE2_SET_REG 0xa5
+#define ANX9804_TRAINING_LANE3_SET_REG 0xa6
+
+#define ANX9804_LINK_TRAINING_CTRL_REG 0xa8
+#define ANX9804_LINK_TRAINING_CTRL_EN BIT(0)
+
+#define ANX9804_LINK_DEBUG_REG 0xb8
+#define ANX9804_PLL_CTRL_REG 0xc7
+#define ANX9804_ANALOG_POWER_DOWN_REG 0xc8
+
+/* Registers at i2c address 0x39 */
+
+#define ANX9804_DEV_IDH_REG 0x03
+
+#define ANX9804_POWERD_CTRL_REG 0x05
+#define ANX9804_POWERD_AUDIO BIT(4)
+
+#define ANX9804_RST_CTRL_REG 0x06
+
+#define ANX9804_RST_CTRL2_REG 0x07
+#define ANX9804_RST_CTRL2_AUX BIT(2)
+#define ANX9804_RST_CTRL2_AC_MODE BIT(6)
+
+#define ANX9804_VID_CTRL1_REG 0x08
+#define ANX9804_VID_CTRL1_VID_EN BIT(7)
+#define ANX9804_VID_CTRL1_EDGE BIT(0)
+
+#define ANX9804_VID_CTRL2_REG 0x09
+#define ANX9804_ANALOG_DEBUG_REG1 0xdc
+#define ANX9804_ANALOG_DEBUG_REG3 0xde
+#define ANX9804_PLL_FILTER_CTRL1 0xdf
+#define ANX9804_PLL_FILTER_CTRL3 0xe1
+#define ANX9804_PLL_FILTER_CTRL 0xe2
+#define ANX9804_PLL_CTRL3 0xe6
+
+/**
+ * anx9804_init() - Init anx9804 parallel lcd to edp bridge chip
+ *
+ * This function will init an anx9804 parallel lcd to dp bridge chip
+ * using the passed in parameters.
+ *
+ * @i2c_bus: Number of the i2c bus to which the anx9804 is connected.
+ * @lanes: Number of displayport lanes to use
+ * @data_rate: Register value for the bandwidth reg 0x06: 1.62G, 0x0a: 2.7G
+ * @bpp: Bits per pixel, must be 18 or 24
+ */
+void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp)
+{
+ unsigned int orig_i2c_bus = i2c_get_bus_num();
+ u8 c, colordepth;
+ int i;
+
+ i2c_set_bus_num(i2c_bus);
+
+ if (bpp == 18)
+ colordepth = 0x00; /* 6 bit */
+ else
+ colordepth = 0x10; /* 8 bit */
+
+ /* Reset */
+ i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 1);
+ mdelay(100);
+ i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 0);
+
+ /* Write 0 to the powerdown reg (powerup everything) */
+ i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, 0);
+
+ c = i2c_reg_read(0x39, ANX9804_DEV_IDH_REG);
+ if (c != 0x98) {
+ printf("Error anx9804 chipid mismatch\n");
+ i2c_set_bus_num(orig_i2c_bus);
+ return;
+ }
+
+ for (i = 0; i < 100; i++) {
+ c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
+ i2c_reg_write(0x38, ANX9804_SYS_CTRL2_REG, c);
+ c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
+ if ((c & ANX9804_SYS_CTRL2_CHA_STA) == 0)
+ break;
+
+ mdelay(5);
+ }
+ if (i == 100)
+ printf("Error anx9804 clock is not stable\n");
+
+ i2c_reg_write(0x39, ANX9804_VID_CTRL2_REG, colordepth);
+
+ /* Set a bunch of analog related register values */
+ i2c_reg_write(0x38, ANX9804_PLL_CTRL_REG, 0x07);
+ i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL3, 0x19);
+ i2c_reg_write(0x39, ANX9804_PLL_CTRL3, 0xd9);
+ i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE);
+ i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG1, 0xf0);
+ i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG3, 0x99);
+ i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL1, 0x7b);
+ i2c_reg_write(0x38, ANX9804_LINK_DEBUG_REG, 0x30);
+ i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL, 0x06);
+
+ /* Force HPD */
+ i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
+ ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL);
+
+ /* Power up and configure lanes */
+ i2c_reg_write(0x38, ANX9804_ANALOG_POWER_DOWN_REG, 0x00);
+ i2c_reg_write(0x38, ANX9804_TRAINING_LANE0_SET_REG, 0x00);
+ i2c_reg_write(0x38, ANX9804_TRAINING_LANE1_SET_REG, 0x00);
+ i2c_reg_write(0x38, ANX9804_TRAINING_LANE2_SET_REG, 0x00);
+ i2c_reg_write(0x38, ANX9804_TRAINING_LANE3_SET_REG, 0x00);
+
+ /* Reset AUX CH */
+ i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
+ ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX);
+ i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
+ ANX9804_RST_CTRL2_AC_MODE);
+
+ /* Powerdown audio and some other unused bits */
+ i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO);
+ i2c_reg_write(0x38, ANX9804_HDCP_CONTROL_0_REG, 0x00);
+ i2c_reg_write(0x38, 0xa7, 0x00);
+
+ /* Set data-rate / lanes */
+ i2c_reg_write(0x38, ANX9804_LINK_BW_SET_REG, data_rate);
+ i2c_reg_write(0x38, ANX9804_LANE_COUNT_SET_REG, lanes);
+
+ /* Link training */
+ i2c_reg_write(0x38, ANX9804_LINK_TRAINING_CTRL_REG,
+ ANX9804_LINK_TRAINING_CTRL_EN);
+ mdelay(5);
+ for (i = 0; i < 100; i++) {
+ c = i2c_reg_read(0x38, ANX9804_LINK_TRAINING_CTRL_REG);
+ if ((c & 0x01) == 0)
+ break;
+
+ mdelay(5);
+ }
+ if(i == 100) {
+ printf("Error anx9804 link training timeout\n");
+ i2c_set_bus_num(orig_i2c_bus);
+ return;
+ }
+
+ /* Enable */
+ i2c_reg_write(0x39, ANX9804_VID_CTRL1_REG,
+ ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE);
+ /* Force stream valid */
+ i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
+ ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL |
+ ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL);
+
+ i2c_set_bus_num(orig_i2c_bus);
+}
projects / u-boot.git / commitdiff