]> git.dujemihanovic.xyz Git - u-boot.git/commitdiff
ARM: mvebu: add additional information to board_add_ram_info()
authorJoshua Scott <joshua.scott@alliedtelesis.co.nz>
Mon, 4 Sep 2017 05:38:32 +0000 (17:38 +1200)
committerStefan Roese <sr@denx.de>
Tue, 26 Sep 2017 04:51:50 +0000 (06:51 +0200)
Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is

  SoC:   MV88F6820-A0 at 1600 MHz
  DRAM:  2 GiB (800 MHz, 32-bit, ECC not enabled)

Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
arch/arm/mach-mvebu/dram.c

index e3f304c36683bb67aceffc0f6bd9474fad195830..55e9ad726a88618a57d09bcd91216dde3dcaf539 100644 (file)
@@ -216,6 +216,35 @@ static int ecc_enabled(void)
 
        return 0;
 }
+
+/* Return the width of the DRAM bus, or 0 for unknown. */
+static int bus_width(void)
+{
+       int full_width = 0;
+
+       if (reg_read(REG_SDRAM_CONFIG_ADDR) & (1 << REG_SDRAM_CONFIG_WIDTH_OFFS))
+               full_width = 1;
+
+       switch (mvebu_soc_family()) {
+       case MVEBU_SOC_AXP:
+           return full_width ? 64 : 32;
+           break;
+       case MVEBU_SOC_A375:
+       case MVEBU_SOC_A38X:
+       case MVEBU_SOC_MSYS:
+           return full_width ? 32 : 16;
+       default:
+           return 0;
+       }
+}
+
+static int cycle_mode(void)
+{
+       int val = reg_read(REG_DUNIT_CTRL_LOW_ADDR);
+
+       return (val >> REG_DUNIT_CTRL_LOW_2T_OFFS) & REG_DUNIT_CTRL_LOW_2T_MASK;
+}
+
 #else
 static void dram_ecc_scrubbing(void)
 {
@@ -295,10 +324,26 @@ int dram_init_banksize(void)
 void board_add_ram_info(int use_default)
 {
        struct sar_freq_modes sar_freq;
+       int mode;
+       int width;
 
        get_sar_freq(&sar_freq);
        printf(" (%d MHz, ", sar_freq.d_clk);
 
+       width = bus_width();
+       if (width)
+               printf("%d-bit, ", width);
+
+       mode = cycle_mode();
+       /* Mode 0 = Single cycle
+        * Mode 1 = Two cycles   (2T)
+        * Mode 2 = Three cycles (3T)
+        */
+       if (mode == 1)
+               printf("2T, ");
+       if (mode == 2)
+               printf("3T, ");
+
        if (ecc_enabled())
                printf("ECC");
        else