#include <asm/immap_83xx.h>
#define NUM_OF_PINS 32
-void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign)
+
+/** qe_cfg_iopin configure one io pin setting
+ *
+ * @par_io: pointer to parallel I/O base
+ * @port: io pin port
+ * @pin: io pin number which get configured
+ * @dir: direction of io pin 2 bits valid
+ * 00 = pin disabled
+ * 01 = output
+ * 10 = input
+ * 11 = pin is I/O
+ * @open_drain: is pin open drain
+ * @assign: pin assignment registers select the function of the pin
+ */
+static void qe_cfg_iopin(qepio83xx_t *par_io, u8 port, u8 pin, int dir,
+ int open_drain, int assign)
{
- u32 2bit_mask;
- u32 2bit_dir;
- u32 2bit_assign;
- u32 1bit_mask;
- u32 tmp_val;
- immap_t *im;
- qepio83xx_t *par_io;
- int offset;
+ u32 dbit_mask;
+ u32 dbit_dir;
+ u32 dbit_asgn;
+ u32 bit_mask;
+ u32 tmp_val;
+ int offset;
- im = (immap_t *)CONFIG_SYS_IMMR;
- par_io = (qepio83xx_t *)&im->qepio;
offset = (NUM_OF_PINS - (pin % (NUM_OF_PINS / 2) + 1) * 2);
/* Calculate pin location and 2bit mask and dir */
- 2bit_mask = (u32)(0x3 << offset);
- 2bit_dir = (u32)(dir << offset);
+ dbit_mask = (u32)(0x3 << offset);
+ dbit_dir = (u32)(dir << offset);
/* Setup the direction */
tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
in_be32(&par_io->ioport[port].dir1);
if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io->ioport[port].dir2, ~2bit_mask & tmp_val);
- out_be32(&par_io->ioport[port].dir2, 2bit_dir | tmp_val);
+ out_be32(&par_io->ioport[port].dir2, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].dir2, dbit_dir | tmp_val);
} else {
- out_be32(&par_io->ioport[port].dir1, ~2bit_mask & tmp_val);
- out_be32(&par_io->ioport[port].dir1, 2bit_dir | tmp_val);
+ out_be32(&par_io->ioport[port].dir1, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].dir1, dbit_dir | tmp_val);
}
/* Calculate pin location for 1bit mask */
- 1bit_mask = (u32)(1 << (NUM_OF_PINS - (pin + 1)));
+ bit_mask = (u32)(1 << (NUM_OF_PINS - (pin + 1)));
/* Setup the open drain */
tmp_val = in_be32(&par_io->ioport[port].podr);
if (open_drain)
- out_be32(&par_io->ioport[port].podr, 1bit_mask | tmp_val);
+ out_be32(&par_io->ioport[port].podr, bit_mask | tmp_val);
else
- out_be32(&par_io->ioport[port].podr, ~1bit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].podr, ~bit_mask & tmp_val);
/* Setup the assignment */
tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
in_be32(&par_io->ioport[port].ppar2) :
in_be32(&par_io->ioport[port].ppar1);
- 2bit_assign = (u32)(assign << offset);
+ dbit_asgn = (u32)(assign << offset);
/* Clear and set 2 bits mask */
if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io->ioport[port].ppar2, ~2bit_mask & tmp_val);
- out_be32(&par_io->ioport[port].ppar2, 2bit_assign | tmp_val);
+ out_be32(&par_io->ioport[port].ppar2, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].ppar2, dbit_asgn | tmp_val);
} else {
- out_be32(&par_io->ioport[port].ppar1, ~2bit_mask & tmp_val);
- out_be32(&par_io->ioport[port].ppar1, 2bit_assign | tmp_val);
+ out_be32(&par_io->ioport[port].ppar1, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].ppar1, dbit_asgn | tmp_val);
}
}
+
+#if !defined(CONFIG_PINCTRL)
+/** qe_config_iopin configure one io pin setting
+ *
+ * @port: io pin port
+ * @pin: io pin number which get configured
+ * @dir: direction of io pin 2 bits valid
+ * 00 = pin disabled
+ * 01 = output
+ * 10 = input
+ * 11 = pin is I/O
+ * @open_drain: is pin open drain
+ * @assign: pin assignment registers select the function of the pin
+ */
+void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ qepio83xx_t *par_io = (qepio83xx_t *)&im->qepio;
+
+ qe_cfg_iopin(par_io, port, pin, dir, open_drain, assign);
+}
+#endif
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *
+ * Dave Liu <daveliu@freescale.com>
+ * based on source code of Shlomi Gridish
+ */
+
+#include <common.h>
+#include <linux/errno.h>
+#include <asm/io.h>
+#include <asm/immap_83xx.h>
+
+#if defined(CONFIG_PINCTRL)
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <dm/pinctrl.h>
+#include <linux/ioport.h>
+
+/**
+ * struct qe_io_platdata
+ *
+ * @base: Base register address
+ * @num_par_io_ports number of io ports
+ */
+struct qe_io_platdata {
+ qepio83xx_t *base;
+ u32 num_io_ports;
+};
+#endif
+
+#define NUM_OF_PINS 32
+
+/** qe_cfg_iopin configure one io pin setting
+ *
+ * @par_io: pointer to parallel I/O base
+ * @port: io pin port
+ * @pin: io pin number which get configured
+ * @dir: direction of io pin 2 bits valid
+ * 00 = pin disabled
+ * 01 = output
+ * 10 = input
+ * 11 = pin is I/O
+ * @open_drain: is pin open drain
+ * @assign: pin assignment registers select the function of the pin
+ */
+static void qe_cfg_iopin(qepio83xx_t *par_io, u8 port, u8 pin, int dir,
+ int open_drain, int assign)
+{
+ u32 dbit_mask;
+ u32 dbit_dir;
+ u32 dbit_asgn;
+ u32 bit_mask;
+ u32 tmp_val;
+ int offset;
+
+ offset = (NUM_OF_PINS - (pin % (NUM_OF_PINS / 2) + 1) * 2);
+
+ /* Calculate pin location and 2bit mask and dir */
+ dbit_mask = (u32)(0x3 << offset);
+ dbit_dir = (u32)(dir << offset);
+
+ /* Setup the direction */
+ tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
+ in_be32(&par_io->ioport[port].dir2) :
+ in_be32(&par_io->ioport[port].dir1);
+
+ if (pin > (NUM_OF_PINS / 2) - 1) {
+ out_be32(&par_io->ioport[port].dir2, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].dir2, dbit_dir | tmp_val);
+ } else {
+ out_be32(&par_io->ioport[port].dir1, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].dir1, dbit_dir | tmp_val);
+ }
+
+ /* Calculate pin location for 1bit mask */
+ bit_mask = (u32)(1 << (NUM_OF_PINS - (pin + 1)));
+
+ /* Setup the open drain */
+ tmp_val = in_be32(&par_io->ioport[port].podr);
+ if (open_drain)
+ out_be32(&par_io->ioport[port].podr, bit_mask | tmp_val);
+ else
+ out_be32(&par_io->ioport[port].podr, ~bit_mask & tmp_val);
+
+ /* Setup the assignment */
+ tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
+ in_be32(&par_io->ioport[port].ppar2) :
+ in_be32(&par_io->ioport[port].ppar1);
+ dbit_asgn = (u32)(assign << offset);
+
+ /* Clear and set 2 bits mask */
+ if (pin > (NUM_OF_PINS / 2) - 1) {
+ out_be32(&par_io->ioport[port].ppar2, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].ppar2, dbit_asgn | tmp_val);
+ } else {
+ out_be32(&par_io->ioport[port].ppar1, ~dbit_mask & tmp_val);
+ out_be32(&par_io->ioport[port].ppar1, dbit_asgn | tmp_val);
+ }
+}
+
+#if !defined(CONFIG_PINCTRL)
+/** qe_config_iopin configure one io pin setting
+ *
+ * @port: io pin port
+ * @pin: io pin number which get configured
+ * @dir: direction of io pin 2 bits valid
+ * 00 = pin disabled
+ * 01 = output
+ * 10 = input
+ * 11 = pin is I/O
+ * @open_drain: is pin open drain
+ * @assign: pin assignment registers select the function of the pin
+ */
+void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ qepio83xx_t *par_io = (qepio83xx_t *)&im->qepio;
+
+ qe_cfg_iopin(par_io, port, pin, dir, open_drain, assign);
+}
+#else
+static int qe_io_ofdata_to_platdata(struct udevice *dev)
+{
+ struct qe_io_platdata *plat = dev->platdata;
+ fdt_addr_t addr;
+
+ addr = dev_read_addr(dev);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ plat->base = (qepio83xx_t *)addr;
+ if (dev_read_u32(dev, "num-ports", &plat->num_io_ports))
+ return -EINVAL;
+
+ return 0;
+}
+
+/**
+ * par_io_of_config_node config
+ * @dev: pointer to pinctrl device
+ * @pio: ofnode of pinconfig property
+ */
+static int par_io_of_config_node(struct udevice *dev, ofnode pio)
+{
+ struct qe_io_platdata *plat = dev->platdata;
+ qepio83xx_t *par_io = plat->base;
+ const unsigned int *pio_map;
+ int pio_map_len;
+
+ pio_map = ofnode_get_property(pio, "pio-map", &pio_map_len);
+ if (!pio_map)
+ return -ENOENT;
+
+ pio_map_len /= sizeof(unsigned int);
+ if ((pio_map_len % 6) != 0) {
+ dev_err(dev, "%s: pio-map format wrong!\n", __func__);
+ return -EINVAL;
+ }
+
+ while (pio_map_len > 0) {
+ /*
+ * column pio_map[5] from linux (has_irq) not
+ * supported in u-boot yet.
+ */
+ qe_cfg_iopin(par_io, (u8)pio_map[0], (u8)pio_map[1],
+ (int)pio_map[2], (int)pio_map[3],
+ (int)pio_map[4]);
+ pio_map += 6;
+ pio_map_len -= 6;
+ }
+ return 0;
+}
+
+int par_io_of_config(struct udevice *dev)
+{
+ u32 phandle;
+ ofnode pio;
+ int err;
+
+ err = ofnode_read_u32(dev_ofnode(dev), "pio-handle", &phandle);
+ if (err) {
+ dev_err(dev, "%s: pio-handle not available\n", __func__);
+ return err;
+ }
+
+ pio = ofnode_get_by_phandle(phandle);
+ if (!ofnode_valid(pio)) {
+ dev_err(dev, "%s: unable to find node\n", __func__);
+ return -EINVAL;
+ }
+
+ /* To Do: find pinctrl device and pass it */
+ return par_io_of_config_node(NULL, pio);
+}
+
+/*
+ * This is not nice!
+ * pinsettings should work with "pinctrl-" properties.
+ * Unfortunately on mpc83xx powerpc linux device trees
+ * devices handle this with "pio-handle" properties ...
+ *
+ * Even worser, old board code inits all par_io
+ * pins in one step, if U-Boot uses the device
+ * or not. So init all par_io definitions here too
+ * as linux does this also.
+ */
+static void config_qe_ioports(struct udevice *dev)
+{
+ ofnode ofn;
+
+ for (ofn = dev_read_first_subnode(dev); ofnode_valid(ofn);
+ ofn = dev_read_next_subnode(ofn)) {
+ /*
+ * ignore errors here, as may the subnode
+ * has no pio-handle
+ */
+ par_io_of_config_node(dev, ofn);
+ }
+}
+
+static int par_io_pinctrl_probe(struct udevice *dev)
+{
+ config_qe_ioports(dev);
+
+ return 0;
+}
+
+static int par_io_pinctrl_set_state(struct udevice *dev, struct udevice *config)
+{
+ return 0;
+}
+
+const struct pinctrl_ops par_io_pinctrl_ops = {
+ .set_state = par_io_pinctrl_set_state,
+};
+
+static const struct udevice_id par_io_pinctrl_match[] = {
+ { .compatible = "fsl,mpc8360-par_io"},
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(par_io_pinctrl) = {
+ .name = "par-io-pinctrl",
+ .id = UCLASS_PINCTRL,
+ .of_match = of_match_ptr(par_io_pinctrl_match),
+ .probe = par_io_pinctrl_probe,
+ .ofdata_to_platdata = qe_io_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct qe_io_platdata),
+ .ops = &par_io_pinctrl_ops,
+#if CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)
+ .flags = DM_FLAG_PRE_RELOC,
+#endif
+};
+#endif
projects / u-boot.git / commitdiff