arm: mvebu: a38x: Adjust UTMI PHY parameters

When running USB compliance tests on our Armada-385 hardware platforms
we have seen some eye mask violations. Marvell's internal documentation
says: Based on silicon test results, it is recommended to change the
impedance calibration threshold setting to 0x6 prior to calibration.

Port changes from Marvell's u-boot fork[1] to address this.

[1] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/a6221551

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
index d4480622c89c82a7a39c2e9e91cc40a2f30ff154..2454730e6d860e59e75f13de65a090638b2dd907 100644 (file)
--- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
+++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
@@ -672,12 +672,29 @@ struct op_params usb2_power_up_params[] = {
        {0xc200c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0},
        /* Phy0 register 3  - TX Channel control 0 */
        {0xc400c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0},
-       /* check PLLCAL_DONE is set and IMPCAL_DONE is set */
+       /* Decrease the amplitude of the low speed eye to meet the spec */
+       {0xc000c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0},
+       {0xc200c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0},
+       {0xc400c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0},
+       /* Change the High speed impedance threshold */
+       {0xc0008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
+       {0xc2008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
+       {0xc4008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
+       /* Change the squelch level of the receiver to meet the receiver electrical measurements (squelch and receiver sensitivity tests) */
+       {0xc0014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0},
+       {0xc2014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0},
+       {0xc4014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0},
+       /* Check PLLCAL_DONE is set and IMPCAL_DONE is set */
        {0xc0008, 0x0 /*NA*/, 0x80800000, {0x80800000}, 1, 1000},
-       /* check REG_SQCAL_DONE  is set */
+       /* Check REG_SQCAL_DONE  is set */
        {0xc0018, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000},
-       /* check PLL_READY  is set */
-       {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000}
+       /* Check PLL_READY  is set */
+       {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000},
+       /* Start calibrate of high seed impedance */
+       {0xc0008, 0x0 /*NA*/, 0x2000, {0x2000}, 0, 0},
+       {0x0, 0x0 /*NA*/, 0x0, {0x0}, 10, 0},
+       /* De-assert  the calibration signal */
+       {0xc0008, 0x0 /*NA*/, 0x2000, {0x0}, 0, 0},
 };
 
 /*