From affcba728b90428f38e6ea6b945935146c8f3dcb Mon Sep 17 00:00:00 2001 From: Ashok Reddy Soma Date: Fri, 9 Jul 2021 05:53:40 -0600 Subject: [PATCH] mmc: zynq_sdhci: Allow configuring zero Tap values Allow configuring ITAP and OTAP values with zero to avoid failures in some cases (one of them is SD boot mode). Legacy, SDR12 modes require to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104 modes ITAP value is zero. In SD boot mode firmware configures the SD ITAP and OTAP values and in this case u-boot has to re-configure required tap values(including zero) based on the operating mode. Signed-off-by: Ashok Reddy Soma Reviewed-by: Jaehoon Chung Signed-off-by: Michal Simek --- drivers/mmc/zynq_sdhci.c | 16 ++++------------ 1 file changed, 4 insertions(+), 12 deletions(-) diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c index 5bad5cb9e7..f65a87a4e1 100644 --- a/drivers/mmc/zynq_sdhci.c +++ b/drivers/mmc/zynq_sdhci.c @@ -198,9 +198,7 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct sdhci_host *host, * ZynqMP does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ - if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300 || - timing == MMC_TIMING_LEGACY || - timing == MMC_TIMING_UHS_SDR12 || !degrees) + if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { @@ -253,9 +251,7 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct sdhci_host *host, * ZynqMP does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ - if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300 || - timing == MMC_TIMING_LEGACY || - timing == MMC_TIMING_UHS_SDR12 || !degrees) + if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { @@ -307,9 +303,7 @@ static int sdhci_versal_sdcardclk_set_phase(struct sdhci_host *host, * Versal does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ - if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300 || - timing == MMC_TIMING_LEGACY || - timing == MMC_TIMING_UHS_SDR12 || !degrees) + if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { @@ -370,9 +364,7 @@ static int sdhci_versal_sampleclk_set_phase(struct sdhci_host *host, * Versal does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ - if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300 || - timing == MMC_TIMING_LEGACY || - timing == MMC_TIMING_UHS_SDR12 || !degrees) + if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { -- 2.39.5