Marek Vasut [Thu, 3 Jan 2019 20:19:24 +0000 (21:19 +0100)]
mmc: Add support for downgrading HS200/HS400 to HS mode
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
omap3: igep00x0: Remove USB support due DM_USB deadline
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar] Signed-off-by: Tom Rini <trini@konsulko.com>
Shawn Guo [Tue, 18 Dec 2018 09:52:06 +0000 (17:52 +0800)]
poplar: add DWC2 OTG gadget support
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Booting an image currently sets the environment variable "fdtaddr"
by calling into 'cmd/fdt.c'. As a result, linking U-Boot fails if
CMD_FDT is not enabled.
Fix this by adding 'if (CONFIG_IS_ENABLED(CMD_FDT))' to the two
places where 'set_working_fdt_addr()' is called.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Fabio Estevam [Sat, 29 Dec 2018 12:02:24 +0000 (10:02 -0200)]
imx8mq_evk_defconfig: Move file system options to Kconfig
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
Alex Elder [Tue, 18 Dec 2018 03:08:18 +0000 (11:08 +0800)]
poplar: save environment at a different offset
Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC
than before. This puts it immediately prior to the space we are
reserving offset 0x200000-0x400000 for UEFI to save its persistent
data. Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the
sector size, like CONFIG_ENV_OFFSET is.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tom Rini [Fri, 11 Jan 2019 14:54:44 +0000 (09:54 -0500)]
Revert "fs: fat: assign rootdir sector when accessing root directory"
This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16. Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.
As reported by Alex Kiernan the above optimization introduces a
regression in the below use case where:
1. Device has defined 'u-boot,dm-spl' property (@ eMMC DTS node)
2. The device downloads its MLO/SPL via UART (not eMMC - the eMMC pinmux
pins are NOT probed/configured in MLO/SPL).
3. The loaded via UART MLO/SPL wants to load Linux from eMMC. In this case
the DM core and pinctrl uclass checks 'u-boot,dm-spl' and don't
configure pins (as it thinks that those were initialized in MLO/SPL).
As we are very close to release - please revert this commit.
Reported-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
dm: usb: gadget: Fix boot breakage on sunxi platforms
Fixes commit 013116243950 ("dm: usb: create a new UCLASS ID for USB gadget
devices")
The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.
Reported-by: Priit Laes <plaes@plaes.org> Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Priit Laes <plaes@plaes.org> Acked-by: Jagan Teki <jagan@openedev.com>
dm: usb: udc: Use SEQ_ALIAS to index the USB gadget ports
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)
To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).
If no alias is provided, then the index falls back to the order in which
the bindings took place.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reported-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Peng Fan [Sat, 15 Dec 2018 12:19:58 +0000 (12:19 +0000)]
tools: imx8image: set dcd_skip to true
To B0[+] chips, dcd_skip needs to be true. For A0 chip, it needs
to be false, however A0 chip is no longer being supported anymore.
Considering we are moving code from imx-mkimage to uboot mkimage,
to make sure we not introduce some surprise, we still keep dcd_skip
code there.
Peng Fan [Sat, 15 Dec 2018 12:19:46 +0000 (12:19 +0000)]
clk: imx8: fix build warning
When build clk driver in spl, met the warning:
"
drivers/clk/imx/clk-imx8.c:21:25: warning: ‘imx8_clk_names’ defined but not used [-Wunused-variable]
static struct imx8_clks imx8_clk_names[] = {
^~~~~~~~~~~~~~
"
Soeren Moch [Sat, 5 Jan 2019 08:31:18 +0000 (09:31 +0100)]
board: tbs2910: Remove FIT support in defconfig to reduce u-boot size
The current defconfig build generates a u-boot.imx file that is too large
for the available space on a eMMC/SD card. Installing this file overwrites
the u-boot environment. So disable the unused FIT support to reduce the
size of the u-boot binary.
Chris Spencer [Thu, 20 Dec 2018 09:25:24 +0000 (09:25 +0000)]
imx: Add Makefile dependency for mkimage_fit_atf.sh
The mkimage_fit_atf.sh SPL FIT generator script requires
u-boot-nodtb.bin, but this was not enforced by the Makefile. This could
cause the generator script to be executed before u-boot-nodtb.bin has
been created.
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Stefan Agner [Tue, 4 Dec 2018 10:10:21 +0000 (11:10 +0100)]
ARM: vf610: ddrmc: do not write CR79 by default
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Stefan Agner [Tue, 4 Dec 2018 10:10:18 +0000 (11:10 +0100)]
toradex: colibri_vf: fix memory initialization
Commit 3f353ceccbbb ("vf610: refactor DDRMC code") changed on-die
termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static
read/write leveling which has not been tested with this board. This
commit reverts both changes and makes sure that memory gets
initialized as it has been done before the mentioned commit.
Fixes: 3f353ceccbbb ("vf610: refactor DDRMC code") Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Stefan Agner [Fri, 14 Dec 2018 14:26:00 +0000 (15:26 +0100)]
ARM: vf610: ddrmc: program Dummy DDRBYTE1/2
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Patrice Chotard [Fri, 4 Jan 2019 09:55:06 +0000 (10:55 +0100)]
gpio: stm32f7: Fix SPL code size
In order to keep SPL code size below the 32Kb limit,
put under CONFIG_SPL_BUILD flag all unused code in SPL.
This is needed for stm32f7xx board which are using SPL.
Patrice Chotard [Fri, 4 Jan 2019 09:55:05 +0000 (10:55 +0100)]
gpio: stm32f7: Fix gpio bank hole management
In case "gpio-ranges" property is not present in device tree,
use default value for gpio_count and gpio_range.
This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a"
command didn't return any pin status due to the fact that both stm32 F7
and H7 board DT doesn't use the gpio-ranges property.
Sam Protsenko [Fri, 4 Jan 2019 20:09:08 +0000 (22:09 +0200)]
arm: ti: boot: Remove legacy Android partitions
Remove unused Android partitions:
- efs, crypto, cache: we don't use it anymore (images are not built
in AOSP
- ipu1, ipu2: IPU firmware is now a part of vendor image and doesn't
reside as a separate partition
While at it, rename "reserved" partition to "uboot-env", as it's
actually stores U-Boot environment.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Ye Li [Fri, 4 Jan 2019 09:34:24 +0000 (09:34 +0000)]
env: sata: Add missed env location for SATA boot
The env location label ENVL_ESATA is missed in location tables, so
when we configure the ENV in SATA, u-boot fails to get correct env
location and cause boot hang in board_f.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 4 Jan 2019 09:24:14 +0000 (09:24 +0000)]
arm: Round the dma_alloc_coherent memory size to cache line aligned
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
igep003x: MAINTAINER: Remove myself as maintainer and add Javier
I can't continue maintaining the board because I don't have access to the
hardware anymore, so remove myself from the entry and add Javier who has
volunteered to help and maintain the board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Javier Martínez Canillas <javier@dowhile0.org>
Tom Rini [Thu, 27 Dec 2018 14:22:55 +0000 (09:22 -0500)]
Add a github template telling people to not use pull requests there
On our mirror account on github we have gotten a handful of pull
requests. At this time github does not allow you to disable pull
requests on a project. The generally suggested work-around is to add a
pull request template that tells people to not use that workflow. Add
one here that points to the wiki page on submitted patches.
Andre Przywara [Mon, 17 Dec 2018 10:05:45 +0000 (10:05 +0000)]
mmc: bring back partition init for non-DM MMC drivers
Commit d0851c893706 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Soeren Moch <smoch@web.de>
Andre Przywara [Mon, 17 Dec 2018 10:05:44 +0000 (10:05 +0000)]
sunxi: drop default SPL_LIBDISK_SUPPORT enablement
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 8 Jan 2019 03:57:56 +0000 (22:57 -0500)]
Makefile: Correct logic for DM_SCSI + unconverted drivers check
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_DM_SCSI by itself, as that is not a bug.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com> Fixes: ea9d7c17fc4c ("dm: MIGRATION: Add migration plan for CONFIG_SATA") Signed-off-by: Tom Rini <trini@konsulko.com>
Philipp Tomsich [Fri, 4 Jan 2019 18:09:08 +0000 (19:09 +0100)]
rockchip: rk3399: fix missing braces in full pinctrl
Braces around the error-case for rk3399_pinctrl_set_pin_pupd lead to
an unconditional (and unintended) return from the function without it
ever setting pin-configurations.
Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 3 Jan 2019 13:39:44 +0000 (08:39 -0500)]
Merge tag 'for-master-20190103' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for 2019.1:
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
rockchip: rk3399: Add Kconfig option for full pinctrl driver
This patch adds a Kconfig option to enable the full pinctrl driver
for the RK3399. This flag needs to be enabed in order to get the
features of the full pinctrl driver compiled in (i.e. a .set_state()
callback).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The current pinctrl driver for the RK3399 has a range of qulity issues.
E.g. it only implements the .set_state_simple() callback, it
does not parse the available pinctrl information from the DTS
(instead uses hardcoded values), is not flexible enough to cover
devices without 'interrupt' field in the DTS (e.g. PWM),
is not written generic enough to make code reusable among other
rockchip SoCs...
This patch addresses these issues by reimplementing the whole driver
from scratch using the .set_state() callback.
The new implementation covers all featurese of the old code
(i.e. it supports pinmuxing and pullup/pulldown configuration).
This patch has been tested on a RK3399-Q7 SoM (Puma).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Fri, 28 Dec 2018 01:56:48 +0000 (09:56 +0800)]
rockchip: sdram-common: fix wrong size for 4GB in 32bit SoC
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-By: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log